EA6500 v2 as Access Point

Similar Questions

• EA6500-double WUMC710-WRT310N as Access Point

  After getting a Smart TV for my basement last year, I was unable to get a proper my WRT310N wireless signal.  I had the WRT310N on the second floor with my desktop PC.  Wifi should reach the basement, but not good enough to stream hi-def movies.  To remedy this, I bought a router of EA6500 and the WUMC710 bridge to replace the WRT310N.  I put the EA6500 on the ground floor, the bridge in the basement and I was using Powerline to access my PC upstairs.  I become disillusioned by the stability of the signal by current bearer of the PC upstairs, so I bought another WUMC710 to my floor.  This configuration is therefore works very well, EA6500 ground floor with of two WUMC710, one upstairs and one in the basement.  The only problem I have left is a wifi dead spot in the master bedroom.  I not was too concerned about the place of the dead since we do not use wifi in the bedroom very often, but I recently heard that it is possible to use my old router, the WRT10N, as an access point to extend my range of wifi.  I followed some instructions of the internet to get the WRT310N set up as access point (disable DHCP, configure phrase password and security, the same as on the EA6500 router).  I then used the power lines through a signal ethernet of the EA6500, the son of AC, in the House of the masters of whetre the other carrier current module online is now connected.  I then connected the WRT310N to this Powerline online and the WiFi in the room was now nice and sharp.  Note that this WRT310N is out now wifi in the main room, while in the corridor on the other side of the second story sits the WUMC710 bridge, which is connected to the EA6500 via wifi. At some point during the day wifi stop working throughout the House.  My suspicion is that the WUMC710 passed the EA6500 wifi signal and picked up the WRT310N wifi.  The only way I could get wifi back working again was to unplug the WRT310N access point.  Is there a way to put bridges (WUMC710) so that they will only connect to the EA6500 and NOT the WRT310N?

  Hello. Given that both routers are set up with the same wireless name and password, your WUMC710 will connect to one of them. If you wish, you can configure - your WRT310N with other wireless name and password so that your bridge will connect with EA6500. This should help.

• My Airport Time Capsule can act as a WIRELESS access point

  Hello.

  I brought a Time Capsule with my Mac Pro. It worked well since yesterday.

  I have set up the time Capsule as a WIFI, bypass at my local network access point. There is a router (cable) works at home.

  It's my Mac Pro AirPort Utility and my iPhone, my Time Capsule is displayed with an exclamation point saying "device not found". I can't connect to the disk on this subject by afp share, or smb. Time Machine function is gone too. He failed trying to connect to the share drive from another computer connected to the time Capsule by cable network.

  But at the same time, WiFi works well.

  I tried to recycle energy. Sharing disk will be available. But if I start the Time Machine backup, it will not be a few seconds.

  Any idea?

  Thank you.

  There are several posts here related the issue.

  Luckily, you have set up your new Time Capsule for Back to My Mac (BTMM)?

  If so, the 'temporary' solution is to delete/disable the option of the CCMM, as follows:

  • Run the AirPort Utility.
  • Select the base and then station, select change.
  • On the tab of the Base Station, go back to the section of my Mac at the bottom of the window.
  • If you have entries here, select it and click then the minus sign "-" button to remove it.
  • Click on update and allow the base station restart.

  If you have not enabled CCMM, we have other options for you to try.

• Do I need an additional access point to use my iPod touch for audio books? It's using iOS 9.3

  Do I need an additional access point to use my iPod touch to listen to audio books.  The iPod is on iOS 9.3 and my iMac on OS 10.11.4.  I can get the books from the library using the OverDrive Media Console software, then by moving the iTunes audio book using 'add to library '.  Then, it presents itself in music and can be downloaded from there to the iPod.  The audio book also appear in the section music from iPod.  The problem is, most of the time, no list of book sections appear on the iPod and the iPod plays sections in random order instead of sequentially.  I can't find anything in the guide of the user on audio books.

  Can you import into your application iBooks on Mac and then sync it with your iPod?

  See chapter iBooks of:

  http://help.Apple.com/iPod-touch/9/#/iphbaeb5b5cb

• Stor.E access point stops working after a few seconds

  Bought a Stor.E wireless adapter and followed the instructions but after turn on the unit by connecting to USB power usage provides cables, access point WIFI disconnects after 4 or around seconds.
  1. I connect to usb power
  2. the indicator flashes in green and stays on
  3. wireless light turns green and stay on, turns off after a few seconds

  Managed to connect using the mobile app several times, while its sequel, but given that the WIFI point disconnects, can't use it.

  Any thoughts?

  1. I connect to usb power

  Stor.e wireless adapter must be connected to the power supply and the other end to the external HARD drive.

  

  Then, you can use the application to access the wireless content.

• Time Capsule bridge and access point?

  Hello

  I have a question about the network wireless of my TC. Our provider has installed a new router. These router can not work as bridge, telephone and TV are also connected to this router. Because 2 wifi networks do not work, I wonder what is the best set-up for the network? The Capsule is connected to the router by ethernet. It is configured as a gateway. Before I used the TC to connect to internet. Now, I have disabled the wi - fi function and use the ISP connection. It looks good, only backups are a little slow now.

  -What is the best configuration for the TC in an existing network? So that I can put it off the wireless of the TC or the ISP router: can I use the TC-wifi (create a new network) or wifi existing ISP router to connect with wireless devices?

  -Do I lose speed when I'm with 2 devices on my network: TC as the ISP as a router and Access Point.

  (I always thought that 1 unit for router and access point is the best configuration.)

  -Are faster backup copies using the TC wireless or it does not matter when I backup on the wireless ISP?

  Some maybe stupid questions, but thanks in advance. Greetings.

  Because 2 wifi networks do not work

  Many people think that this is the case... but this isn't so.

  You can use several wireless networks... all attached to the same router. There is enough bandwidth available in the channels wireless for the operation of 3 different wireless networks nearby each other... and using 5 GHz adds much more.

  The Capsule is connected to the router by ethernet. It is configured as a gateway. Before I used the TC to connect to internet. Now, I have disabled the wi - fi function and use the ISP connection. It looks good, only backups are a little slow now.

  The configuration of TC in bridge is correct.

  Do not turn off the TC wireless... Provide a different name for the ISP wireless router and connect your computer... then you can get internet and make backups on the TC without overloading the ISP router wireless.

  -What is the best configuration for the TC in an existing network? If I disable the wireless of the TC or the ISP router:

  Turn on Wi - Fi in both.

  A physical configuration, it is recommended to have say separation of 1 M (3 feet) between the ISP router and the TC to a min. But it would be even better to have the TC at near the Mac who performs backups TM and related to the ISP router with ethernet.

• Use WAN connected airport Time Capsule as a wireless access point

  I had to replace a failed 4 Gen Time Capsule. I tried to install a new Gen 5 airport TimeCapsule via WAN and set up the airport to act as a wireless access point. It is installed in an area of my house with wireless coverage. In the network of AirPort Utility Mode section, I chose "extend a wireless network. The TC is restarted, I get an error message cannot find the intended wireless network.

  What I lack?

  "Extend a wireless network" is a parameter that is only used if the time Capsule need to connect to another router from Apple with the help of a Wi-Fi connection.

  You use Ethernet to connect, you must use the parameter to "create a wireless network. Use the same wireless network name and the same password as your "primary" router

• Satellite P875 - 32L - is unable to reconnect to the last connected WIFI access point

  I have a problem to reconnect to the last connected WLAN provider, with my Satellite P875 32 L.
  WLAN is switched on and shows all the neighbors access points, but it fails to whoever I logged before the reboot, or before you go to the rescue of the list.

  I'm going in service options for WLAN, sometiimes up to 5 times, then it undermines meet usually.
  It's well annoying.

  I have had this with the other 30 satellite of P870 too, but something so this behavior have disappeared. So there must be a solution.

  Hello

  You're talking about your private Wlan at home?
  If you had the same problem using another laptop too, it could be possible that this isn't a problem with the network s laptop wireless card or Wlan configuration but with the WLan router.

  You should definitely reset/reboot the rooter.
  In addition, check the settings of the IP router and or mac address filtering.
  Change also the type of encryption and Wlan channel.

  You have to try different combination turn off just to test the WiFi encryption and check if the laptop would connect to the Wlan open correctly.
  But the Wlan encryption must always be defined in order to avoid improper use of the Wlan access point.

• Problem with access point or wireless adapter

  Hello world

  tried to connect to my WiFi, but the convenience store detects that the problem with access point or wireless adapter.
  The drivers are up-to-date and functioning normally. There were discussions on BIOS but I don't know if I would be able to complete the task without bricking your laptop.

  Is there any online support?

  Hi smert

  Your message is not really useful.
  Why? Because no one knows all the details of the laptop, wireless network card system...
  So please would you be kind enough to provide more details.

  But despite the missing information, I recommend:
  (1) reset your router WLan
  (2) check the connection to the WiFi unsecured. (of course for testing purposes)
  (3) check the different (WPA/WPA2 AES, TKIP) encryption

• Latest drivers Atheros does not help with hotspot WiFi (or access point)?

  I updated the drivers from v7.7.0.288.0. It's the latest and probably the last pilot found in archive of drivers for the A200 support.

  I set up my WiFi Atheros in usual manner of Vista. The steps are described in most PC portals for the creation of an access point WiFi in Windows Vista.

  1 Control Panel
  2 network connections and sharing
  3. ad-hoc creation, the SSID, password etc.
  4. share the internet connection button.
  5 allow to other users on the network to use my internet
  6 access point is created and Windows indicates that the signal is "Excellent".

  Everything is simple and straightforward but my Android smartphones don't detect access point.
  So what is the fault?

  Driver details dated 03/09/2009 in the Page of Support Toshiba informed that the update of the wireless Lan driver is to 'connect to your wireless access Point or to another PC wireless using your wireless network card.

  [driver | http://www.toshiba.eu/innovation/download_driver_details.jsp?service=EU&selCategory = 8 & selFamily = 192 & selSeries = 236 & selProduct = 725 & STAS hortMod = 518 & language = 13 & selOS = 26 & selType = 97 & yearup load = & monthupload = & dayupload = & useDate = null & mode = al lMachines & search = & action = search & macId = & country = all & selectedLanguage = 13 & type = 97 & page = 1 & ID = 54134 & DISO = 26 & driverLanguage = 42]

  COMPUTER geeks report that my Atheros AR5007EG is able to create the gateway under Win7. I think in the same way, it should work with Windows Vista SP2.

  http://www.itgeekdiary.com/Windows-7-as-an-Wi-Fi-access-point/

  I tried other portals Windows but all of them describe the same steps by creating ad hoc to access Windows Vista point.

  Any help is appreciated.

  Kind regards.

  Thanks for the comments!

• SA50-122 / intel BG2200 - no found Access Point

  Hi all

  I have a Satellite SA50-122 with a processor intel BG2200 access WLAN chipset. When I started the book the first time clean windows software WLAN does not detect any access point. After you have installed the latest available suite intel (Intel® PRO/Wireless 2200BG Network Connection - 9.0.2.0) this has worked excelent!

  (Note: intel sw now WLAN Management)

  But now, after a few weeks, it no longer works...

  I tried to do a repair installation, have uninstalled the intel SW, installed the latest version (9.0.2.1) again and again, but without success!

  :-(

  Someone there simular problems and have some tips on what caused it?

  Thanks in advance,
  Peter

  Hi taschenwolf

  It s nice that you have solved the problem.
  I'm sure that this info helps our community.

  Best regards

• Can I use my Satellite P10 as Access Point?

  Satellite P10 wireless access point

  Please can someone help?
  I have a laptop wireless by Satellite P10, can anyone tell me is it possible to set up the laptop to share my Internet remotely even if its WiFi, so it can be picked up by my Sony PSP. Then my cell phone would act as a wireless internet access point.
  As I do not have a router, don t know if it is possible this way any ideas?
  Thank you Michael.

  Hi Michael

  Well, I m not sure if it of possible the Sony PSP to connect to the laptop and if it works, but I found several useful information how to create make it the network connection wireless home in Windows XP without a router. Please check this links.

  http://www.Microsoft.com/windowsxp/using/networking/expert/bowman_02april08.mspx

  http://www.annoyances.org/exec/show/ics_xp.

  Good luck

  Good bye

• How can I get my name from the access point?

  Since I bought a modem Arris 228 G and spent my 2 wireless, printers Canon WIFI unable to connect at Optimum!

  Canon said to contact my router creator (Apple Airport Extreme) for the name of the access point get return wireless, WI - FI printers.

  Help, please.

  W.W.

  (Mac Pro 10.6.8)

  The name of the access point is simply the name of the wireless network that provides AirPort Extreme.

  You can see the name of your wireless network by clicking on the WiFi icon at the top of the screen of your Mac and by checking that the name appears.

  

  There will be a check mark next to your wireless network name.. which is also known as a wireless access point.

  It would be the same name that you had before... unless you have changed some settings on the AirPort Extreme.

• WiFi HP ENVY 4500 with several Access Points - same SSIS Configuration

  Hello

  We just got a HP ENVY 4500.  I have a main homenetwork with a wifi Modem/Router and an old router acting as an Access Point to the floor to extend coverage.

  Both have the same SSID and password and are set to different channels.

  My HP ENVY 4500 fails to connect when the Access Point is lit.

  It will connect with it.

  Once connected, I can turn on the PA and all is well.

  The two router an AP using WPA-PSK/WPA2-PSK encriptación

  The router (that it connects to) should have a better sgnal when both are on, so I do not understand why they need the AP to be turned off to connect.

  Any thoughts people?

  Eserim

  I think he has always had problems with several access points.  Try this, what ever AP is closest to the printer, set it to channel 1.  Then try channel 11.  Try now.

• Cannot connect by Satellite L300 wireless access point

  I have a new laptop L300 & I can't connect to the laptop to my wireless access point. I have an another mobile E-sytems with the same hardware Realtek RTL8187B & it connects without problems.

  The machine has the free two month Mcafee subscription & I have disabled all the protection incase that was causing the problem. I updated the driver for the wireless card & the bios on the Toshiba site, but nothing is.

  Can someone shed light on this problem because the laptop is only two weeks old?

  Thank you...

  Hello

  To connect the laptop to the WLan, it must ensure that everything is enabled and configured correctly.
  You should check these points:

  -activated the WLan with the WLan switch and the FN + F8
  -don t use any 3rd party config tools WLan if you use the WLan configuration options own Vista
  -for the first test WLan disable the security settings of the Wlan router
  -configure settings to laptop as good SSID and search for your wireless local area network
  -After that the laptop is connected to the WLan router, you can turn back the security settings (encryption, mac address filtering, firewall, etc.)

  Welcome them