Easy VPN not able to access the local network

Hi guys,.

little hope can help me, I'll give you a run down on the config.

I have a border router that is a no. 2851 connected to the No. 2851 is a switch cisco 3750 running Routing inter - vlan with four VLANS.

I have easy VPN server on the edge router No. 2851 I am able to connect remotely from a client vpn cisco with a problem but I can't access the local network on the server, I tried everything with no luck.

I have a cisco VPN client installed on a 64-bit windows system 7 and I also tried with windows xp 32-bit system and still no luck.

Please I need help I need to get this race to end of trading today.

I will be copying and pasting the edge router config please if someone get review and see if the config is good.

You need to change your ACL PAT of standard to extend and to deny traffic to be translated to the Pool of VPN:

access-list 120 deny ip 10.10.10.0 0.0.0.3 10.10.50.0 0.0.0.255

access-list 120 deny ip 192.168.XX.0 0.0.0.255 10.10.50.0 0.0.0.255

access-list 120 deny ip 172.16.XX.0 0.0.0.255 10.10.50.0 0.0.0.255

access-list 120 deny ip 172.1X.20.0 0.0.0.255 10.10.50.0 0.0.0.255

access-list 120 deny ip 192.168.XX.0 0.0.0.255 10.10.50.0 0.0.0.255

access-list 120 allow ip 10.10.10.0 0.0.0.3 all

IP access-list 120 permit 192.168.XX.0 0.0.0.255 any

IP access-list 120 permit 172.16.XX.0 0.0.0.255 aniy

IP access-list 120 permit 172.1X.20.0 0.0.0.255 any

IP access-list 120 permit 192.168.XX.0 0.0.0.255 any

overload of IP nat inside source list 120 interface Dialer0

no nat ip within the source of the list 1 overload interface Dialer0

clear the ip nat trans *.

Hope that helps.

Tags: Cisco Security

Similar Questions

  • ASA 5505 IPSEC VPN connected but cannot access the local network

    ASA: 8.2.5

    ASDM: 6.4.5

    LAN: 10.1.0.0/22

    Pool VPN: 172.16.10.0/24

    Hi, we purcahsed a new ASA 5505 and try to configure IPSEC VPN via ASDM; I simply run the wizards, installation vpnpool, split tunnelling, etc.

    I can connect to the ASA using the cisco VPN client and internet works fine on the local PC, but it can not access the local network (can not impossible. ping remote desktop). I tried the same thing on our Production ASA(those have both Remote VPN and Site-to-site VPN working), the new profile, I created worked very well.

    Here is my setup, wrong set up anything?

    ASA Version 8.2 (5)

    !

    hostname asatest

    domain XXX.com

    activate 8Fw1QFqthX2n4uD3 encrypted password

    g9NiG6oUPjkYrHNt encrypted passwd

    names of

    !

    interface Ethernet0/0

    switchport access vlan 2

    !

    interface Ethernet0/1

    !

    interface Ethernet0/2

    !

    interface Ethernet0/3

    !

    interface Ethernet0/4

    !

    interface Ethernet0/5

    !

    interface Ethernet0/6

    !

    interface Ethernet0/7

    !

    interface Vlan1

    nameif inside

    security-level 100

    IP 10.1.1.253 255.255.252.0

    !

    interface Vlan2

    nameif outside

    security-level 0

    address IP XXX.XXX.XXX.XXX 255.255.255.240

    !

    passive FTP mode

    clock timezone PST - 8

    clock summer-time recurring PDT

    DNS server-group DefaultDNS

    domain vff.com

    vpntest_splitTunnelAcl list standard access allowed 10.1.0.0 255.255.252.0

    access extensive list ip 10.1.0.0 inside_nat0_outbound allow 255.255.252.0 172.16.10.0 255.255.255.0

    pager lines 24

    Enable logging

    timestamp of the record

    logging trap warnings

    asdm of logging of information

    logging - the id of the device hostname

    host of logging inside the 10.1.1.230

    Within 1500 MTU

    Outside 1500 MTU

    IP local pool 172.16.10.1 - 172.16.10.254 mask 255.255.255.0 vpnpool

    no failover

    ICMP unreachable rate-limit 1 burst-size 1

    don't allow no asdm history

    ARP timeout 14400

    Global 1 interface (outside)

    NAT (inside) 0-list of access inside_nat0_outbound

    NAT (inside) 1 0.0.0.0 0.0.0.0

    Route outside 0.0.0.0 0.0.0.0 XXX.XXX.XXX.XXX 1

    Timeout xlate 03:00

    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

    timeout tcp-proxy-reassembly 0:01:00

    Floating conn timeout 0:00:00

    dynamic-access-policy-registration DfltAccessPolicy

    AAA-server protocol nt AD

    AAA-server host 10.1.1.108 AD (inside)

    NT-auth-domain controller 10.1.1.108

    Enable http server

    http 10.1.0.0 255.255.252.0 inside

    No snmp server location

    No snmp Server contact

    Server enable SNMP traps snmp authentication linkup, linkdown cold start

    Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

    Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

    Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

    Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

    Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

    Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

    life crypto ipsec security association seconds 28800

    Crypto ipsec kilobytes of life - safety 4608000 association

    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

    Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

    outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

    outside_map interface card crypto outside

    crypto ISAKMP allow outside

    crypto ISAKMP policy 10

    preshared authentication

    3des encryption

    sha hash

    Group 2

    life 86400

    Telnet timeout 5

    SSH 10.1.0.0 255.255.252.0 inside

    SSH timeout 20

    Console timeout 0

    dhcpd outside auto_config

    !

    a basic threat threat detection

    Statistics-list of access threat detection

    no statistical threat detection tcp-interception

    WebVPN

    internal group vpntest strategy

    Group vpntest policy attributes

    value of 10.1.1.108 WINS server

    Server DNS 10.1.1.108 value

    Protocol-tunnel-VPN IPSec l2tp ipsec

    disable the password-storage

    disable the IP-comp

    Re-xauth disable

    disable the PFS

    IPSec-udp disable

    IPSec-udp-port 10000

    Split-tunnel-policy tunnelspecified

    value of Split-tunnel-network-list vpntest_splitTunnelAcl

    value by default-domain XXX.com

    disable the split-tunnel-all dns

    Dungeon-client-config backup servers

    the address value vpnpool pools

    admin WeiepwREwT66BhE9 encrypted privilege 15 password username

    username user5 encrypted password privilege 5 yIWniWfceAUz1sUb

    the encrypted password privilege 3 umNHhJnO7McrLxNQ util_3 username

    tunnel-group vpntest type remote access

    tunnel-group vpntest General attributes

    address vpnpool pool

    authentication-server-group AD

    authentication-server-group (inside) AD

    Group Policy - by default-vpntest

    band-Kingdom

    vpntest group tunnel ipsec-attributes

    pre-shared-key BEKey123456

    NOCHECK Peer-id-validate

    !

    !

    privilege level 3 mode exec cmd command perfmon

    privilege level 3 mode exec cmd ping command

    mode privileged exec command cmd level 3

    logging of the privilege level 3 mode exec cmd commands

    privilege level 3 exec command failover mode cmd

    privilege level 3 mode exec command packet cmd - draw

    privilege show import at the level 5 exec mode command

    privilege level 5 see fashion exec running-config command

    order of privilege show level 3 exec mode reload

    privilege level 3 exec mode control fashion show

    privilege see the level 3 exec firewall command mode

    privilege see the level 3 exec mode command ASP.

    processor mode privileged exec command to see the level 3

    privilege command shell see the level 3 exec mode

    privilege show level 3 exec command clock mode

    privilege exec mode level 3 dns-hosts command show

    privilege see the level 3 exec command access-list mode

    logging of orders privilege see the level 3 exec mode

    privilege, level 3 see the exec command mode vlan

    privilege show level 3 exec command ip mode

    privilege, level 3 see fashion exec command ipv6

    privilege, level 3 see the exec command failover mode

    privilege, level 3 see fashion exec command asdm

    exec mode privilege see the level 3 command arp

    command routing privilege see the level 3 exec mode

    privilege, level 3 see fashion exec command ospf

    privilege, level 3 see the exec command in aaa-server mode

    AAA mode privileged exec command to see the level 3

    privilege, level 3 see fashion exec command eigrp

    privilege see the level 3 exec mode command crypto

    privilege, level 3 see fashion exec command vpn-sessiondb

    privilege level 3 exec mode command ssh show

    privilege, level 3 see fashion exec command dhcpd

    privilege, level 3 see the vpnclient command exec mode

    privilege, level 3 see fashion exec command vpn

    privilege level see the 3 blocks from exec mode command

    privilege, level 3 see fashion exec command wccp

    privilege see the level 3 exec command mode dynamic filters

    privilege, level 3 see the exec command in webvpn mode

    privilege control module see the level 3 exec mode

    privilege, level 3 see fashion exec command uauth

    privilege see the level 3 exec command compression mode

    level 3 for the show privilege mode configure the command interface

    level 3 for the show privilege mode set clock command

    level 3 for the show privilege mode configure the access-list command

    level 3 for the show privilege mode set up the registration of the order

    level 3 for the show privilege mode configure ip command

    level 3 for the show privilege mode configure command failover

    level 5 mode see the privilege set up command asdm

    level 3 for the show privilege mode configure arp command

    level 3 for the show privilege mode configure the command routing

    level 3 for the show privilege mode configure aaa-order server

    level mode 3 privilege see the command configure aaa

    level 3 for the show privilege mode configure command crypto

    level 3 for the show privilege mode configure ssh command

    level 3 for the show privilege mode configure command dhcpd

    level 5 mode see the privilege set privilege to command

    privilege level clear 3 mode exec command dns host

    logging of the privilege clear level 3 exec mode commands

    clear level 3 arp command mode privileged exec

    AAA-server of privilege clear level 3 exec mode command

    privilege clear level 3 exec mode command crypto

    privilege clear level 3 exec command mode dynamic filters

    level 3 for the privilege cmd mode configure command failover

    clear level 3 privilege mode set the logging of command

    privilege mode clear level 3 Configure arp command

    clear level 3 privilege mode configure command crypto

    clear level 3 privilege mode configure aaa-order server

    context of prompt hostname

    no remote anonymous reporting call

    Cryptochecksum:447bbbc60fc01e9f83b32b1e0304c6b4

    : end

    Captures we can see packets going from the pool to the internal LAN, but we do not reply back packages.

    The routing must be such that for 172.16.10.0/24 packages should reach the inside interface of the ASA.

    On client machines or your internal LAN switch, you need to add route for 172.16.10.0/24 pointing to the inside interface of the ASA.

  • remote VPN and vpn site to site vpn remote users unable to access the local network

    As per below config remote vpn and vpn site to site vpn remote users unable to access the local network please suggest me a required config

    The local 192.168.215.4 not able ping server IP this server connectivity remote vpn works fine but not able to ping to the local network vpn users.

    ASA Version 8.2 (2)
    !
    host name
    domain kunchevrolet
    activate r8xwsBuKsSP7kABz encrypted password
    r8xwsBuKsSP7kABz encrypted passwd
    names of
    !
    interface Ethernet0/0
    nameif outside
    security-level 0
    PPPoE client vpdn group dataone
    IP address pppoe
    !
    interface Ethernet0/1
    nameif inside
    security-level 50
    IP 192.168.215.2 255.255.255.0
    !
    interface Ethernet0/2
    nameif Internet
    security-level 0
    IP address dhcp setroute
    !
    interface Ethernet0/3
    Shutdown
    No nameif
    no level of security
    no ip address
    !
    interface Management0/0
    Shutdown
    No nameif
    no level of security
    no ip address
    management only
    !
    passive FTP mode
    clock timezone IST 5 30
    DNS server-group DefaultDNS
    domain kunchevrolet
    permit same-security-traffic intra-interface
    object-group network GM-DC-VPN-Gateway
    object-group, net-LAN
    access extensive list ip 192.168.215.0 sptnl allow 255.255.255.0 192.168.2.0 255.255.255.0
    192.168.215.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.2.0 255.255.255.0
    tunnel of splitting allowed access list standard 192.168.215.0 255.255.255.0
    pager lines 24
    Enable logging
    asdm of logging of information
    Outside 1500 MTU
    Within 1500 MTU
    MTU 1500 Internet
    IP local pool VPN_Users 192.168.2.1 - 192.168.2.250 mask 255.255.255.0
    ICMP unreachable rate-limit 1 burst-size 1
    enable ASDM history
    ARP timeout 14400
    NAT-control
    Global 1 interface (outside)
    NAT (inside) 1 0.0.0.0 0.0.0.0
    Route outside 0.0.0.0 0.0.0.0 59.90.214.1 1
    Timeout xlate 03:00
    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    dynamic-access-policy-registration DfltAccessPolicy
    the ssh LOCAL console AAA authentication
    AAA authentication LOCAL telnet console
    AAA authentication http LOCAL console
    AAA authentication enable LOCAL console
    LOCAL AAA authentication serial console
    Enable http server
    x.x.x.x 255.255.255.252 out http
    http 192.168.215.0 255.255.255.252 inside
    http 192.168.215.0 255.255.255.0 inside
    No snmp server location
    No snmp Server contact
    Server enable SNMP traps snmp authentication linkup, linkdown cold start
    Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT
    life crypto ipsec security association seconds 28800
    Crypto ipsec kilobytes of life - safety 4608000 association
    Crypto-map dynamic dynmap 65500 transform-set RIGHT
    card crypto 10 VPN ipsec-isakmp dynamic dynmap
    card crypto VPN outside interface
    card crypto 10 ASA-01 set peer 221.135.138.130
    card crypto 10 ASA - 01 the transform-set RIGHT value
    crypto ISAKMP allow outside
    crypto ISAKMP policy 10
    preshared authentication
    3des encryption
    sha hash
    Group 2
    life 86400
    crypto ISAKMP policy 65535
    preshared authentication
    the Encryption
    sha hash
    Group 2
    lifetime 28800
    Telnet 192.168.215.0 255.255.255.0 inside
    Telnet timeout 5
    SSH 0.0.0.0 0.0.0.0 outdoors
    SSH timeout 5
    Console timeout 0
    management-access inside
    VPDN group dataone request dialout pppoe
    VPDN group dataone localname bb4027654187_scdrid
    VPDN group dataone ppp authentication chap
    VPDN username bb4027654187_scdrid password * local store
    interface for identifying DHCP-client Internet customer
    dhcpd dns 218.248.255.141 218.248.245.1
    !
    dhcpd address 192.168.215.11 - 192.168.215.254 inside
    dhcpd allow inside
    !
    a basic threat threat detection
    Statistics-list of access threat detection
    no statistical threat detection tcp-interception
    Des-sha1 encryption SSL
    WebVPN
    allow outside
    tunnel-group-list activate
    internal kun group policy
    kun group policy attributes
    VPN - connections 8
    Protocol-tunnel-VPN IPSec
    Split-tunnel-policy tunnelspecified
    Split-tunnel-network-list value split tunnel
    kunchevrolet value by default-field
    test P4ttSyrm33SV8TYp encrypted password username
    username kunauto password bSHrKTGl8PUbvus / encrypted privilege 15
    username kunauto attributes
    Strategy Group-VPN-kun
    Protocol-tunnel-VPN IPSec
    tunnel-group vpngroup type remote access
    tunnel-group vpngroup General attributes
    address pool VPN_Users
    Group Policy - by default-kun
    tunnel-group vpngroup webvpn-attributes
    the vpngroup group alias activation
    vpngroup group tunnel ipsec-attributes
    pre-shared key *.
    type tunnel-group test remote access
    tunnel-group x.x.x.x type ipsec-l2l
    tunnel-group ipsec-attributes x.x.x.x
    pre-shared key *.
    !
    class-map inspection_default
    match default-inspection-traffic
    !
    !
    type of policy-card inspect dns preset_dns_map
    parameters
    maximum message length automatic of customer
    message-length maximum 512
    Policy-map global_policy
    class inspection_default
    inspect the preset_dns_map dns
    inspect the ftp
    inspect h323 h225
    inspect the h323 ras
    Review the ip options
    inspect the netbios
    inspect the rsh
    inspect the rtsp
    inspect the skinny
    inspect esmtp
    inspect sqlnet
    inspect sunrpc
    inspect the tftp
    inspect the sip
    inspect xdmcp
    inspect the icmp
    !
    global service-policy global_policy
    context of prompt hostname
    call-home
    Profile of CiscoTAC-1
    no active account
    http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
    email address of destination [email protected] / * /
    destination-mode http transport
    Subscribe to alert-group diagnosis
    Subscribe to alert-group environment
    Subscribe to alert-group monthly periodic inventory
    monthly periodicals to subscribe to alert-group configuration
    daily periodic subscribe to alert-group telemetry
    Cryptochecksum:0d2497e1280e41ab3875e77c6b184cf8
    : end
    kunauto #.

    Hello

    Looking at the configuration, there is an access list this nat exemption: -.

    192.168.215.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.2.0 255.255.255.0

    But it is not applied in the States of nat.

    Send the following command to the nat exemption to apply: -.

    NAT (inside) 0 access-list sheep

    Kind regards

    Dinesh Moudgil

    P.S. Please mark this message as 'Responded' If you find this information useful so that it brings goodness to other users of the community

  • Time machine is unable to perform a backup. Not able to access the sparsebundle. Problem occurred first on snow leopard OS. Followed Dragon upgrade to El Capitan. Only difference has error code of 109 changed to null. What about someone?

    Time machine is unable to perform a backup. Not able to access the sparsebundle. First of all, there is problem with the Snow Leopard operating system. Dragon followed in the upgrade to El Capitan. Only difference was error code 109 changed to 'null '. What about someone?

    We need some info.

    You can access from the finder Time Capsule? If this isn't the case, then Time Machine will not work.

    You upgrade the computer snow to El Capo and keep the same name?

    If you want to backup, it is best to start again... clean the new backup any attempt to add a previous backup failed.

    I recommend that you actually erase the TC... do a complete factory reset and start again.

    The previous backup if necessary can be archived on a USB drive connected to the TC assuming that Airport utility can still access it. Airport utility accesses the TC?

    With update installs all sorts of things can go wrong... so tell me more if you can not get anywhere.

  • I'm not able to access the help and support on my xp based computer.

    I have Windows XP Home Edition. I deleted some old programs using Add / Remove button in the control settings.  Also installed an antivirus program.  I noticed that the I help support button is unresponsive and I'm not able to access the system restore.  How can I solve this problem?

    Hello

    1. have you made changes on the computer recently?
    2. what happens when you run the system restore?

    Method 1.
    Let us first start the sfc scan and check if there are any file system corruption.
    a. to do this, click Start, click programs, accessories principally made, right click Guest and then click Run as administrator. If you are prompted for an administrator password or a confirmation, type the password, or click on allow.
    b. type the following command and press ENTER:
    sfc/scannow
    The sfc/scannow command. analyzes all protected system files and replaces incorrect versions with appropriate Microsoft versions.
     
    More information on SFC scan found in this document:
    Description of Windows XP and Windows Server 2003 System File Checker (Sfc.exe)
    http://support.Microsoft.com/kb/310747

    Method 2.
    If the problem persists, then create a new user profile and then copy your current users assigning to this profile. For more information, see:
    How to create and configure user accounts in Windows XP
    http://support.Microsoft.com/kb/279783

    How to copy data from a corrupted to a new profile in Windows XP user profile
    http://support.Microsoft.com/kb/811151

    How to recover damaged Windows XP user profile
    http://support.Microsoft.com/kb/555473

    I hope this helps.

  • Not able to access the Console of the OAM?

    Hi all

    I am facing this problem while I try to connect to the console of the OAM, when the managed server is started I am not able to access the Console of the OAM, but when I stopped the managed server, I am able to access the Console of the OAM. Please guide me on this.

    I need documentation on how exactly the work of the Console of the OAM.

    Thank you

    SJ

    Hi Laura,

    Thanks for giving your valuable time, I was able to understand the question. LoadBalancer settings pointing to another machine where I had not installed OAM.

  • I am not able to access the ranking for the last registered course. I could access it earlier and can verify the points of my colleagues. Please solve this problem.

    I am not able to access the ranking for the last registered course. I could access it earlier and can verify the points of my colleagues. Please solve this problem.

    Hello

    It seems that the "Gamification" has not been activated because learners can win and compare points with their colleagues based on rules defined by the 'administrator ' in the Gamification.

    You can check with the administrator of your side on the Gamification has been activated or not.

    Kind regards

    Ajit

  • Not able to access the photos in PSE12.

    Not able to access the photos in PSE12. Click on the photo and it goes to research. Sometimes, I get a message that the device is disconnected.

    Moved to post in the Photoshop Elements forum.

  • Not able to access the parent instance variable in outside of the methods in child

    Hello

    I don't get why I am not able to access the instance variable parent class apart from the example of the child class methods.
    class Parent
    {
         int a;
    }
    
    class Child extends Parent
    {
         a = 1; // Here i am getting a compilation error that Syntax error on token "a", VariableDeclaratorId expected after this token
         
         void someMethod()
         {
              a = 1;  // Here i am not getting any compilation error while accessing parent class variable
         }
    }
    Can someone let me know the exact reason for this, and what about the talks of error?

    Thank you
    Uday

    Published by: Udaya Shankara Gandhi on June 13, 2012 03:30

    You can only put assignments or expressions inside the methods, of the builders or the initializors class, or when you declare a variable.
    It has nothing to the child which stretches from Parent.

    class Parent {
        int a = 1;
    
        { a = 1; }
    
        public Parent() {
            a = 1;
        }
    
       public void method() {
           a = 1;
       }
    }
    
  • Not able to access the application

    Hi all

    I faced a critical question in the production server. I have an admin and a managed server. The managed server is used by my teammates. Today try to restart the authentintion and also the server is restarted.

    The application deployed on the managed server is also active but when I access the application I confronted th error. "

    Error 500 - Internal Server Error

    Of RFC 2068 Hypertext Transfer Protocol - HTTP/1.1:


    10.5.1 500 internal Server Error

    The server encountered an unexpected condition which prevented him from meeting the demand.



    Application is in Active state. Before restarting the server, I can able to access the application, but now I'm not able to access.

    Please give the solution so that it is the production server. Please urgent


    My Log file:

    < 21 January 2016 17:42:39 IST > < error > < oracle.wcps.client.PersonalizationFilter > < WCS-59515 > < unexpected customer of an exception.

    javax.servlet.ServletException: java.lang.NoSuchMethodError: oracle/adf/view/rich/context/AdfFacesContext.getEndUserMonitoringServices (Ljava/util/list);

    at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.java:342)

    at weblogic.servlet.internal.TailFilter.doFilter(TailFilter.java:26)

    at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)

    at oracle.portlet.client.adapter.adf.ADFPortletFilter.doFilter(ADFPortletFilter.java:32)

    at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)

    at oracle.webcenter.framework.events.dispatcher.EventDispatcherFilter.doFilter(EventDispatcherFilter.java:44)

    at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)

    at oracle.adf.model.servlet.ADFBindingFilter.doFilter(ADFBindingFilter.java:211)

    at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)

    at oracle.adfinternal.view.faces.webapp.rich.RegistrationFilter.doFilter(RegistrationFilter.java:133)

    to org.apache.myfaces.trinidadinternal.webapp.TrinidadFilterImpl$ FilterListChain.doFilter (TrinidadFilterImpl.java:478)

    at oracle.adfinternal.view.faces.activedata.AdsFilter.doFilter(AdsFilter.java:60)

    to org.apache.myfaces.trinidadinternal.webapp.TrinidadFilterImpl$ FilterListChain.doFilter (TrinidadFilterImpl.java:478)

    at org.apache.myfaces.trinidadinternal.webapp.TrinidadFilterImpl._doFilterImpl(TrinidadFilterImpl.java:303)

    at org.apache.myfaces.trinidadinternal.webapp.TrinidadFilterImpl.doFilter(TrinidadFilterImpl.java:208)

    at org.apache.myfaces.trinidad.webapp.TrinidadFilter.doFilter(TrinidadFilter.java:92)

    at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)

    at oracle.wcps.client.PersonalizationFilter.doFilter(PersonalizationFilter.java:75)

    at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)

    at oracle.webcenter.content.integration.servlets.ContentServletFilter.doFilter(ContentServletFilter.java:168)

    at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)

    at oracle.webcenter.lifecycle.filter.LifecycleLockFilter.doFilter(LifecycleLockFilter.java:151)

    at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)

    at oracle.adf.library.webapp.LibraryFilter.doFilter(LibraryFilter.java:180)

    at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)

    to oracle.security.jps.ee.http.JpsAbsFilter$ 1.run(JpsAbsFilter.java:138)

    at java.security.AccessController.doPrivileged(AccessController.java:310)

    at oracle.security.jps.util.JpsSubject.doAsPrivileged(JpsSubject.java:324)

    at oracle.security.jps.ee.util.JpsPlatformUtil.runJaasMode(JpsPlatformUtil.java:464)

    at oracle.security.jps.ee.http.JpsAbsFilter.runJaasMode(JpsAbsFilter.java:121)

    at oracle.security.jps.ee.http.JpsAbsFilter.doFilter(JpsAbsFilter.java:211)

    at oracle.security.jps.ee.http.JpsFilter.doFilter(JpsFilter.java:71)

    at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)

    at oracle.dms.servlet.DMSServletFilter.doFilter(DMSServletFilter.java:163)

    at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)

    at weblogic.servlet.internal.RequestEventsFilter.doFilter(RequestEventsFilter.java:27)

    at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)

    to weblogic.servlet.internal.WebAppServletContext$ ServletInvocationAction.wrapRun (WebAppServletContext.java:3730)

    to weblogic.servlet.internal.WebAppServletContext$ ServletInvocationAction.run (WebAppServletContext.java:3696)

    at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:321)

    at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:120)

    at weblogic.servlet.internal.WebAppServletContext.securedExecute(WebAppServletContext.java:2273)

    at weblogic.servlet.internal.WebAppServletContext.execute(WebAppServletContext.java:2179)

    at weblogic.servlet.internal.ServletRequestImpl.run(ServletRequestImpl.java:1490)

    at weblogic.work.ExecuteThread.execute(ExecuteThread.java:256)

    at weblogic.work.ExecuteThread.run(ExecuteThread.java:221)

    Caused by: java.lang.NoSuchMethodError: oracle/adf/view/rich/context/AdfFacesContext.getEndUserMonitoringServices (Ljava/util/list);

    at oracle.adfinternal.view.faces.monitoring.UserActivityInfoUtils.processUserActivityData(UserActivityInfoUtils.java:294)

    at oracle.adfinternal.view.faces.lifecycle.LifecycleImpl._executePhase(LifecycleImpl.java:581)

    at oracle.adfinternal.view.faces.lifecycle.LifecycleImpl.execute(LifecycleImpl.java:219)

    at javax.faces.webapp.FacesServlet.service(FacesServlet.java:265)

    to weblogic.servlet.internal.StubSecurityHelper$ ServletServiceAction.run (StubSecurityHelper.java:227)

    at weblogic.servlet.internal.StubSecurityHelper.invokeServlet(StubSecurityHelper.java:125)

    at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.java:301)

    at weblogic.servlet.internal.TailFilter.doFilter(TailFilter.java:26)

    at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)

    at oracle.portlet.client.adapter.adf.ADFPortletFilter.doFilter(ADFPortletFilter.java:32)

    at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)

    at oracle.webcenter.framework.events.dispatcher.EventDispatcherFilter.doFilter(EventDispatcherFilter.java:44)

    at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)

    at oracle.adf.model.servlet.ADFBindingFilter.doFilter(ADFBindingFilter.java:211)

    at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)

    at oracle.adfinternal.view.faces.webapp.rich.RegistrationFilter.doFilter(RegistrationFilter.java:133)

    to org.apache.myfaces.trinidadinternal.webapp.TrinidadFilterImpl$ FilterListChain.doFilter (TrinidadFilterImpl.java:478)

    at oracle.adfinternal.view.faces.activedata.AdsFilter.doFilter(AdsFilter.java:60)

    to org.apache.myfaces.trinidadinternal.webapp.TrinidadFilterImpl$ FilterListChain.doFilter (TrinidadFilterImpl.java:478)

    at org.apache.myfaces.trinidadinternal.webapp.TrinidadFilterImpl._doFilterImpl(TrinidadFilterImpl.java:303)

    at org.apache.myfaces.trinidadinternal.webapp.TrinidadFilterImpl.doFilter(TrinidadFilterImpl.java:208)

    at org.apache.myfaces.trinidad.webapp.TrinidadFilter.doFilter(TrinidadFilter.java:92)

    at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)

    at oracle.wcps.client.PersonalizationFilter.doFilter(PersonalizationFilter.java:75)

    at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)

    at oracle.webcenter.content.integration.servlets.ContentServletFilter.doFilter(ContentServletFilter.java:168)

    at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)

    at oracle.webcenter.lifecycle.filter.LifecycleLockFilter.doFilter(LifecycleLockFilter.java:151)

    at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)

    at oracle.adf.library.webapp.LibraryFilter.doFilter(LibraryFilter.java:180)

    at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)

    to oracle.security.jps.ee.http.JpsAbsFilter$ 1.run(JpsAbsFilter.java:138)

    at java.security.AccessController.doPrivileged(AccessController.java:310)

    at oracle.security.jps.util.JpsSubject.doAsPrivileged(JpsSubject.java:324)

    at oracle.security.jps.ee.util.JpsPlatformUtil.runJaasMode(JpsPlatformUtil.java:464)

    at oracle.security.jps.ee.http.JpsAbsFilter.runJaasMode(JpsAbsFilter.java:121)

    at oracle.security.jps.ee.http.JpsAbsFilter.doFilter(JpsAbsFilter.java:211)

    at oracle.security.jps.ee.http.JpsFilter.doFilter(JpsFilter.java:71)

    at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)

    at oracle.dms.servlet.DMSServletFilter.doFilter(DMSServletFilter.java:163)

    at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)

    at weblogic.servlet.internal.RequestEventsFilter.doFilter(RequestEventsFilter.java:27)

    at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)

    to weblogic.servlet.internal.WebAppServletContext$ ServletInvocationAction.wrapRun (WebAppServletContext.java:3730)

    to weblogic.servlet.internal.WebAppServletContext$ ServletInvocationAction.run (WebAppServletContext.java:3696)

    at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:321)

    at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:120)

    at weblogic.servlet.internal.WebAppServletContext.securedExecute(WebAppServletContext.java:2273)

    at weblogic.servlet.internal.WebAppServletContext.execute(WebAppServletContext.java:2179)

    at weblogic.servlet.internal.ServletRequestImpl.run(ServletRequestImpl.java:1490)

    at weblogic.work.ExecuteThread.execute(ExecuteThread.java:256)

    at weblogic.work.ExecuteThread.run(ExecuteThread.java:221)

    >

    Kind regards

    Ove...

    Hello

    Thank you for your help.i found the error and I solved it. Recently I installed oracle HTTP 11.1.1.9 server so it updates some jar files that it is under the oracle_common and oracle_common/modules folder. The version of my application is 11.1.1.6 but the pot that lie beneath the middleware folder is 11.1.1.9. The method I outlined above is amortized in the 11.1.1.9 version. So I copied the jar to another environment and paste it to my environment. Then after restarting the whole area the problem is solved. Thank you all for help.

    Kind regards

    Ove.

  • For 2 days were not able to access the App Store and regular a few adds on my iPad, but can be downloaded on my iPhone. I have reset the router, iPads, etc... No change. Help, please

    I can't access AppStore and some other operations ordinary adds on my iPad. Have reset and all routers. All updates current. I can do on iPhone. Is it me or Apple or what? Help, please

    Hello there jacquelinefrombburg,

    Welcome to the communities of Apple Support! It is a great place to get help with connection problems to the App Store and access other applications on your iPad. I know that there are some applications that I rely on every day, so I'll do my utmost to help find a solution.

    As point of departure, we will you force him to close all open applications on your iPad. Once you've done that, go ahead and reboot your iPad. Once it is up and running, test on the App Store to see if you are able to access. Here are some useful resources to guide you through the process described above:

    Force a nearby application on your iPhone, iPad or iPod touch

    Restart your iPhone, iPad or iPod touch

    If you still have questions, see the steps in this article. Even though the title says iTunes Store, the recommendations would still apply to the App Store.

    If you cannot connect to the iTunes Store

    As a step in isolation, it would be wise to check if you have problems with the App Store and other applications while using a Wi - Fi connection and cell phone. If the problem persists with the two types of connection, try resetting the network settings on your iPad. Please note that you erase all the stored passwords and Wi - Fi networks. To complete this step, go to settings > general > reset > reset network settings. After you restart your iPad, test the apps again.

    Take care!

  • Not able to access the PV which are deployed in the RT using the EPICS IO Server

    Hi, we have NIPXIe 8133 and 1 windows vista (32-bit) PC and I installed LabVIEW 2012 (32 bit) and the required modules. I also have another PC (6.3 Santiago RHEL) based on RedHat Linux and all 3 PCs are connected to the same network. I want to develop an application in which I want to deploy some variables of process in RT and want to access this PVs in Red Hat Linux PC. In order to develop this application, I do RT as a server of EPICS and Red Hat Linux PC as a Client of EPICS. I have deployed some variables of process using Server EPICS in RT now I want to access the value of the PVs in Red hat Linux PC and in this EPIC PC base is already installed but I am not able access PVs that are deployed in RT if you please help me solve this problem. Best regards, Ishan

    I have not assigned by default in one of my system and bridge that was the only problem in my system. Once I have given Defaullt bridge in all systems, I can access all of the HP that are deployed in the RT other 2 machines connected in network.

  • Unable to access the local network with VPN with some ISPS

    Hello

    We have a VPN Remote Access IPSEC with an ASA5505. Install VPN it correctly but can not access the inside or the ASA to my office.

    But at home with another Internet service provider, it works! You can access inside.

    We are trying with other ISP and it works with 2 and does not work with the other 2!

    Office we also have an ASA5505, but we have another VPN other sites that work properly.

    Any ideas?

    Thank you and sorry for my English.

    Add...

    ISAKMP nat-traversal crypto

    That should do the trick! Please rate if this can help.

  • Not able to access the folder of the application on the EAS

    Hi all

    I recently installed 11.1.1.3 EPM system when using Essbase


    After installation and config was complete, I used a command-line prompt and navigated to the Essbase Server bin directory and entered the company user name and the password that it prompted me to... but it starts with the following error message:

    [Sea Dec 05 13:31:56 2012] Local/ESSBASE0 / / / Error (1053002)
    Cannot create the directory of the application: C:\Hyperion\products\Essbase\EssbaseClient\
    app\$ DM_APP$ [no such file or directory]

    [Sea Dec 05 13:31:56 2012] Local/ESSBASE0 / / / Warning (1051221)
    Creating data mining Object Management Application fails with the State [1053002]


    [Sea Dec 05 13:31:57 2012] Local/ESSBASE0 / / / Info (1054032)
    Cannot save Essbase alert function: [@ESSBASEALERT] not enabled

    Need help on this. I am able to open the Regional service console but when you navigate to the applications folder on the local host, I'm not able to create any new application, nor I am able to see the preinstalled (DEMOs) ones.

    Thanks in advance...

    Kind regards.

    Dev

    Dev,

    On the Essbase server, the values of the variables ESSBASEPATH and ARBORPATH should point to C:\Hyperion\products\Essbase\EssbaseServer, not in the EssbaseClient folder.

    Check the paths and change them if necessary.

    It could be that useful...

    KosuruS

  • Not able to access the pa_project_pub.add_task API

    Hello

    I'm not able to run pa_project_pub.add_task. I get "* your current responsibility has no access to this function * ' message when I run my custom procedure of Toad. I also tried other responsibilities, but I get the same error.

    I was able to create a budget with the same responsibility 'Projects, Vision operations (USA)'.


    BEGIN

    fnd_global. APPS_INITIALIZE (1005151,20420,275,0);

    DBMS_APPLICATION_INFO. SET_CLIENT_INFO (204);

    -procedure custom that calls api pa_project_pub.add_task
    pkg_task_upload.tasks_main;

    END;

    Can you get it someone please let me know what could be the problem.


    Kind regards
    Sonali

    Hello

    Please make sure you have no invalid object in the database. If necessary, compile it and try to run the code again (see Note: 364051.1).

    Kind regards
    Hussein

Maybe you are looking for

  • Satellite Pro 4600 - how to extend RAM memory

    I want to increase the RAM in my old Satellite Pro 4600. -Someone could advise me which of the (actually existing) types of RAM cards are suitable?-The laptop has a maximum memory limit, or I can go up to 1 GB (for example)? Thank you.

  • Compaq Mini 110: Reset Bios Compaq Mini 110

    BIOS password is set by mistake and I want to remove it, it shows this: CNU9472T56 when you enter a blank password. Thank you.

  • Mr. Fix it does not 0X803C0107 error code

    I installed earlier Mr. Fixit.  Today, whenever I try to run something, I get an error code0X803C0107. What is the problem?

  • history for deleting the file files

    My NAS is full. I want to save my laptop. Historical files doesn't let me delete the files from the dialog box. Can I find the location of the file and delete the backup manually? I can't find it. If so, what is the path?

  • HP 6730 s, short dst failed

    Hello I have a laptop HP 6730 s with windows 7 install. The last time, I have a few freezing problems. When I start the diagnostic tool, she came back with abstract DST failed, ID 60CC5K-GFX61B-XD6W3F-60RQ03. How should I do? Help, please Thank you.