Emergency aid. Stuck with black screen after installation of el capitan

Similar Questions

• Qosmio F50-125 starts with black screen after a BIOS update

  Hello

  After instalation if new bios (v 2.0), computer sometimes starts with black screen.
  Even the first page that show press F2 to enter the bios is not displayed.

  You have someone older version of bios?
  So, I might try if it's the fault of it.

  Hello

  I think that the old BIOS will not help you because the laptop would have known that you try to update the BIOS to the older version, and it would break to the top of the procedure.
  In addition, the older BIOS is not available on the European driver Toshiba page.
  I think just only a Toshiba ASP had an older version of BIOS.

  Anyway, you said that sometimes happens.
  This means that this issue doesn't still persist
  Hmm. in this case, I recommend the default BIOS settings and update the driver display.

  Check it out!

• the 5s iPhone camera is still stuck in black screen after upgrading to iOS 9.2 still frozen just like with iOS 9.1

  I updated my iphone to iOS 9.1 5s, but the camera does not work, most of the time that it was stuck on the black screen. I read in a forum as there are a lot of users affected by the present. "Waited for the iOS 9.2, hoping that it will fix the bug. Finally iOS 9.2 has been launched. Happy to download it thinking that it is the answer to the question of the camera. For a while camera works perfectly, but after 2 days, it was stuck at the black screen forever. It worsen the problem of camera. Hoping someone can help me to fix my phone's camera. Thank you in advance.

  Try resetting your device. This will not erase your data stored on that device.

  • Press and hold the sleep/wake button
  • Press and hold the Home button
  • Press and hold both buttons until the display turns off and on again with the Apple logo on the subject.

  Alternatively, you can go to settings - general - reset - Reset all settings

  If that doesn't work, restore your device to factory settings. Please note that this will delete the data on your device.

  Take a look this Apple Support article: use iTunes to restore the iPhone, iPad or iPod to factory settings - Apple Support.

  As a final step, try recovery mode. Turn off your unit, then plug it to your computer with the hold home button. Hold down Home button until you see the logo of iTunes on the screen of your device. After that on your computer, you should see the iTunes window saying that your device needs to be restored to factory settings. Click Restore.

  More info here:

  https://support.Apple.com/en-us/HT201263

  If these steps do not work, contact Apple and ask for help.

  https://www.Apple.com/support/iPhone/contact/

• The Windows Setup program does not open. Stuck with black screen.

  Hi all

  I'm trying to install windows 7 from an iso file using Bootcamp assistant, Version 6.0.1 but unfortunately just windows installer does not open so I'm stuck with this black screen. I left my sit MacBookPro autour with this black screen during more than half an hour and after awhile, it gets really hot so I interrupted the "process."

  I have reset the NVRAM (command + alt + p + r) which did nothing.

  I followed the instructions of bootcamp. I downloaded the correct drivers for my model of mac pro book, I created a bootable and partitioned my drive.

  The forum has a lot of "black screen problems" but none of their solutions worked for me.

  Any help would be greatly appreciated!

  Thank you

  1. leave BCA creates the installer from USB, but not to partition your drive.

  2. download the correct drivers to install Windows 7 and previous versions on your Mac with Boot Camp - Apple Support and replace $WinPEDriver$, AutoUnattend.xml, and the entire folder on the drive flash USB2 Bootcamp.

  3. run BCA, connect the USB cable and click only the Windows Installer and test if the Setup program starts.

• 10 windows on Dell Latitude E6420 portable: black screen after installation

  I installed windows 10 pro 64 bit on my computer dell laptop latitude e6420 (he held these windows 7 64 bit) through update online on the recommendation of Microsoft.

  After that installation that it restarts and I got the logo followed dell windows 10 logo and black screen and then on my laptop.

  I plugged my monitor which loaded as soon as I inserted it

  I can work with the computer on my laptop with the monitor, but my laptop screen does not work.

  Windows was working fine I was able to access net and tried to update all the drivers, but he showed me that all drivers are up-to-date.

  I was able to run all my applications smoothly only my computer laptop screen was not working. What are the steps I should follow to make my laptop computer screen work normally back.

  Hi, same problem here. I solved it in "Optimus" enable in the settings screen in the BIOS.

• Computer now put in hibernation, Vista will not boot. Computer stuck on black screen after startup. Help?

  I put my computer on 'Hibernate' when I went to bed. When I woke up, I started the computer learned to manufacturer (HP) computer screen introduction as usual, but windows doesn't not load afterwards, as he usually does: I just get a black screen. Lights supply and all the rest are on. Just nothing happens. Any ideas?

  Can I use the firmware from HP (I guess that's what it is) to confirm that my memory and hard drive are very good. I tried Googling the problem, and some signs indicate a problem with the powercfg parameter. I can't get in cmd.exe to reset because I can't get into windows (although through HP firmware, I can enter in "Administrator: X:\windows\system32\cmd.exe - cmd", which seems the same, but the orders that I see offered on websites do not seem to work - help?). Ditto with Safe Mode. I don't have Vista installation disc.

  Any help is very appreciated.

  Hello

  You need to contact HP and install recovery disks command to perform a repair.

  http://h10025.www1.HP.com/ewfrf/wc/contacthp?LC=en&DLC=en&cc=us

• Windows 8 stuck in black screen after "making auto repairs.

  I had my HP laptop for five months. A few days ago that I opened the lid of my portable computer and it loaded and said "Configure automatic updates" at this stage, it was frozen. I held the power button down to do a hard restart. I turn it back on and it wouldn't start. I did a system refresh, defragment HDD, ran CCleaner and started in safe mode. At this point, the hard turned 100% use no matter what I did. I couldn't find a solution I did a system reset. He reset the whole PC and reinstalled Windows 8.  It got stuck in the facility to a black screen with just my mouse. I turned it off. Now when I turn on my laptop the screen goes black for about 15 seconds, then HP appears with "Automatic repair of preparation" below logo. It does this for about 20 seconds then the screen goes black. I left my computer for about 7 hours and the screen was always return. I do not have windows 8 CD or USB key. What can I do? Nobody here was willing to help with this problem, although there are a lot of Windows 8 users who have this. At this point, I am considering buying a Mac that I can't do it in the face of Windows 8. If someone could help me it would be apprciated. Thank you.

  I tried several repairs. I did a disk check by pressing F2 during the launch, and he said that the hard drive has failed. I contacted HP support and they are sending me a box to put my laptop in which I will return. So they will be replacing as there is somehow guaranteed on this subject. If someone experiences this problem, it is probably a hard disk crash. Good luck

• Black screen after installation of the Agent from the view.

  Hello

  I am facing a weird problem on my windows 8.1.

  I have install for use as a template for a pool automated view 5.1

  When I install the vmtools, after that I installed the agent of sight, I got a black screen.

  I tried several times and I got the same thing.

  I'm not able to convert into a model of deployment of workstations after.

  Can you please help me on this problem.

  Thank you in advance.

  I'm a little unclear - which command do you have installed? If you have installed VMware Tools after the Agent of the view, you need to uninstall and re-install the Agent of the view... It must ALWAYS be installed last, even if you're just updating tools.

  In addition, Windows 8.1 is not supported with view 5.1 IIRC

• Upgrade my laptop from window to window 10 8.1. but black screen after installation

  That I upgrade my laptop from window to window 10 8.1. But finish after the installation of the product monitor goes to black. and the laptop is not started. PL help me short on this problem. and advise me what can I do to cause a short circuit

  How long you wait to determine the installation program does not?

  • Make sure it's the disk activity (look at the hard drive LED light to confirm. If there is, keep waiting. If the Setup program goes beyond 2-3 hours, try the following steps.
  • Turn off the computer. Unplug the unit, then wait 20 minutes to 1 hour.
  • If you use a laptop, remove the battery if the option is available.
  • Disconnect from the Internet (unplug Ethernet and disable Wi - Fi).
  • Plug it in again, make sure that it is disconnected from the Internet, and then start the computer.
  • See if it completes the installation program.
  • If the installation program is finished and you see the desktop with the ability to click on start and launch programs, go ahead to reconnect to the Internet.
  • Update drivers: how: install and update drivers in Windows 10

• Stuck with USB screen after reboot

  I restarted my TouchPad this morning at startup, I saw the HP logo for about 1 second, and then a large USB image appeared. The TouchPad has been sitting on this homescreen more than an hour without change. What should I do to recover up to the ad running? Just a little more information, the TouchPad is 50% battery when I rebooted. Could this be the cause? It would not show a charge indicator?

  Thank you

  Fred D Castillo

  Fred.d.Castillo@gmail

  It turns out that my volume button was stuck/press and was the origin of the problem. It has been fixed now.

  Thank you

  Fred D

• Pavilion 15 - p065tx: Pavilion 15 - p065tx, black screen after BIOS update recommended by HP assistant

  System reboot with black screen after accepting the update of the BIOS recommended by HP assistant this morning. AC power on at least three hours of waiting after the process completed successfully with auto update reboots always.

  Power light is on. Wired broadband light is turned on. Light CAP LOCK keyboard and led speaker hold noway.

  Hard reset has been tried 3 times with no improvement.

  External monitor is connected but no signal has been out of the laptop, screen is black.

  Done a few times this page to reset the BIOS setting blindly:

  http://support.HP.com/us-en/document/c02217843

  BEEPS heard when you press F10 or F5 during procedures. But still black screen.

  What can I try again?  Please advice kindly!

  Hi @ sokw,

  I have read and reviewed the post. Thanks for your reply. It seems that bios is damaged, and that is why the computer does not start. As it cannot be fixed by any software troubleshooting, you will need to contact the HP support by phone for the machine.

  HP technical support are available by clicking on the following link:
  
  http://h22207.www2.HP.com/us-en/?openCLC=true
  
  (1) once the page opens, please select the country in which you are located. Then enter your model of HP on the right number.
  
  (2) then choose "Contact the Support" tab at the top and scroll to the bottom of the page "HP Support - contact" to fill out the form with your details.
  
  (3) Once finished, click the "Show Options" at the bottom right.
  
  (4) Finally, scroll to the bottom of the page and select "Get a phone number." A file number and telephone number will now fill for you.

  I hope this helps. I would like to know how this happens. I really hope that the problem is solved without hassle and the unit works very well. Believe me, I've done everything I can to help by keeping your interests in mind. Please reach out for questions and I'll be there for you help.

  Just to say thank youPlease click the ' Thumbs Up 'button to give a Kudos to appreciate my efforts to help me. If it helps, Please mark this "accepted Solution" because it will help many other people with the same problem to get it resolved without hassle.

  Now carefully and have a wonderful week ahead.

• Persistent black screen after startup on Satellite Pro A210 (PSAFHE)

  Need help, need advice on how to solve a persistant problem with black screen after put into initial service.

  Initially its fine but after the initial Toshiba of the screen just goes black, and the rest in this way, the PC stays on. Have you tried F8 options but all result in the same.

  Help please.

  Hello

  You can access the BIOS by pressing F2?
  Boot from a boot as Recovery DVD disk?

  If both is not possible, I'm afraid you have a serious hardware problem m.
  In this case, I get just speculate on the affected parts. Maybe his problem GPU or motherboard who knows

• Black screen after the failure of the connection - win 10 win7 installation

  Hello

  SYSTEM ERROR
  Cause
  I tried to install win10 on a PC running win7. Installation stalled at 99% and I restarted.
  The problem
  Now he still run win7, but once connected, the screen is completely black except for cursor. Features such as the job-work list as it should and in safe mode, the screen is not black after login.

  PC INFORMATION
  The video card
  My video card is "Mobile Intel (R) 4 Series Express Chipset Family" (driver version: 8.15.10.2202) Driver date: 25/08/2010) and windows tells me that the video card (graphics - in my language) is updated to the latest version.
  The model
  ASUS Pro79I Series. With Windows 7 64 bit

  Mathias, cordially

  Denmark

  Hi Mathias,.

  According to the description of the issue you do not get black screen after login in safe mode. For example, there might be a chance that the display driver is either corrupted or need a update. Please, try the steps to uninstall graphics card in Device Manager, uninstall the drivers of device from the list of programs, and then download the latest drivers from the manufacturer's website.

  Step 1:

  Uninstall the device from Device Manager

  • Open the Device Manager
  • Expand the section of the graphics card .
  • Find the Display card Driver.
  • Graphics Driver right click and choose Uninstall.
  • Select the check box delete the driver for this device.
  • Restart the computer after the uninstall is complete.

  Step 2:

  Uninstall the drivers of device from the list of programs in the control panel

  • Click Start, select Control Panel
  • Now, click on programs and select programs and features.
  • Find the Display card Driver.
  • Display driver card click right and select Uninstall.
  • Restart the computer after the uninstall is complete.

  Step 3:

  Download and install the latest drivers for the graphics card from the Web site of the manufacturer (ASUS)

  Hope it would help. If the problem persists post returns with the required information, the current state of your computer and the result of the proposed suggestion, we will be happy to help you.

  Kind regards

• Satellite M70 - black screen after the installation of recovery

  So far, what I did is put in the Recovery DVD - ROM product. Then when my computer restarts I was invited to restore my computer failing and said. After that he went through this process, that he told me to remove the disc that I did. Now he only get a black screen after the Toshiba screen that gives me options f2 for Setup and f12 for options.

  I don't know what to do now to make my laptop works again. Help, please.

  Hi Zach_1,

  Have you tried to launch the installation of recovery again? Maybe that something was wrong during the first installation, it might have arrived
  Then retry the recovery facility and see what happens.

  If it doesn't work you should try a normal Microsoft disk so determine if the problem is related to hardware or recovery disk.

• At the end of the factory restore, but black screen after "Windows has set up the computer.

  The model in question is VC863AA #UUW

  I want to get back the computer to the factory condition, so I rebooted and you press F11. Everything went exactly like this: http://support.hp.com/us-en/document/c00814731#N72 (chapter "Start a restore from the hard drive and the computer is off")...

  .. until step 10, which States:

  "The computer restarts and continues in the installation of Windows. Complete the configuration screens and wait until the computer finishes the installation program. "Then turn off the computer, reconnect all devices and turn on the computer.

  Yes, the computer restarts. She continues in the Windows installation (it says "medan windows konfigurerar datorn Vanta", which means roughly "Please wait while Windows configures the computer"). After that which was for about 5-10 minutes, the text disappears and the computer restarts by itself.

  After that, he gives a normal load Windows Vista bar and after that black screen. It seems to be a little bit alive but jammed somehow. If I let it be for several hours, he goes to the standby mode. If I wake up, he still won't. I can plug a USB another keyboard and he will make some access to hard drive (load a driver probably). I can press the sleep button and it will go into sleep mode. But if I press the power button / stop briefly, it will NOT stop.

  So finally, after several hours I forced to shut down (by pressing the power button / stop longer). When I start it, it goes back to behave as explained in the previous paragraph.

  If I press F8 during startup and select Safe mode, it goes in safe mode and I get dialogue indicating in Finnish:

  «Asenna Windows: Windows ei voi suorittaa vikasietotilassa asennusta.» See devam fenetresdans asennusta uudelleen tietokoneen kaynnistamalla. »

  Rough translation:

  "Installation of Windows: Windows cannot complete installation in safe mode." "You can continue the installation by restarting the computer.

  If I restart the computer, it goes back to the black screen after the windows loading bar.

  This suggests that there is something in the installation of Windows who jams it.

  I can install Windows Vista from a Vista DVD, but then I can't use the software included with the computer. (App States installation cannot install on a machine that is unauthorized, then of course they are looking for some OEM HP things.)

  Any suggestions on how to fix jam that continues with installing Recovery Windows or how to install the software on a normal Vista would be very appreciated.

  I solved the problem. Good thing I didn't order the restore disks, because that would not have solved the problem.

  I decided to post it because I don't know there will be others who have HP Pavilion Elite m9754sc and will have to face this problem of a black screen after the restoration.

  The fact is that the restore worked perfectly, but in this display card driver is buggy and it causes the screen to go black.

  I thought that what I installed fresh Vista which worked until I installed the driver from the recovery partition display. I tried VGA, outputs HDMI and DVI on the factory installed GeForce GT220 and none worked.

  A defective display driver should normally be no problem we could go in safe mode and fix it to the it. But as with the recovery goes to pre install state (ask what language to use etc.), safe mode does not work.

  So the solution is to unlock the display of the motherboard connectors and remove the factory installed GeForce GT220. Once the recovery and installation of Windows is finished using the graphics card integrated motherboards, you can reconnect the GeForce GT220 and get a updated driver with safe mode.