Encoder 6351 PCIe and quadrature + voltage sensor.

Similar Questions

• R815 error code 2900:0221 CPU voltage sensor

  One of our servers R815 (fitted with quad CPU of Opteron AMD 6380) arrested and turned off during the night last week and arrive in the server room, I noticed that the LCD had turned orange with a warning on a CPU being out of range voltage regulator. After unplug power cords, wait a few seconds and plug it back I turned on the server back once again and the message from the LCD and the server started normally.

  So I ran hardware UEFI diagnostics and it came with an error:

  Test results: fail

  Feature: IPMI

  test: IPMI System_Event_Log_Check

  Error Code 2900:0221

  MSG: IPMI - Nov 04 18:08:34 2015: processor: voltage sensor (1, 2V VDDR)

  State asserted "CPU1".

  Is this something to worry because the server is running at full load on all processor cores 64 for 5 days without any problem? Or is the error message refers to the IPMI/BMC processor and not the Opteron processors?

  Andy

  Hello.

  The procedure to follow before you run any diagnostic is to clear the logs from existing material. The 2900:0221 error Code represents an error previously saved and diagnostic tests failed because only the system chosen this historical error (2900:xxxx). Update the BIOS firmware and iDRAC. Otherwise, everything should be good for now.

• T410 voltage sensor failure

  I have a T410 which turns off after about 30 seconds, without errors or warnings, when I ran diagnostic hardware tests, the system has failed with an error code of: Error Code IPMI 2900:0221, MSG, card system: State of the voltage sensor (5V PC) said "motherboard.  I am not able to stay connected to the server in normal mode but can keep the server running in Mode without failure.  I was not able to identify any errors in the newspapers of Windows that indicate what wrong with the operating system, whether at the time wherever remoteness has informed us that they have problems with this device restart constantly RAID known corruption massive disc I could correct it with the disk check.  The server will start without errors or messages and then just power off after about 30 seconds without warning.  This component can be replaced and is then what would be the part #, since it is out of warranty, I'm looking for all the assistance it can fix this problem because it is always a good waiter who just happened to fail after the warranty expires.

  Thank you

  Oscar1976,

  The error you see (2900:0221) refers to something existing in the newspaper of the hardware of the iDrac. Normally, this is a reference to a mistake in the past. If you access the web interface iDrac and go to the newspapers of material, you can check if this has happened before. Normally the error reappears for a problem is happening now will start with 4400:. When it shows this error occurring? In addition, if you disable Diagnostics equipment newspaper 32bits not report this error.

  With what you describe, it sounds like a problem with the OS, but I would say making sure that the server is up to date BIOS, iDrac and the Raid Controller.  As those who are excessively obsolete can cause problems like that as well.  You would also confirm what controller is installed, as well as of the where the versions of these devices are currently?

  Also, in the operating system would you go to system - advanced - startup and recovery and then check that the is NOT a check mark in the check box automatically restart. This is to see if there is a STOP code that occurs before closing

  Let me know what you see.

• HP 240 G4-328TX: need driver for PCI and Signal Processing controller HP 240 G4-328TX Data Acquisition

  Hello

  Need driver for PCI and Signal Processing controller HP 240 G4-328TX Data Acquisition

  Can anyone provide me please the link for download it for windows 10

  Thank you

  Hello:

  See if this driver works...

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=7609938 & swItemId = ob_153701_1 & swEnvOid = 4192

• HP DC7700: Serial Port PCI and simple Communication controllers pilots missing in HP DC7700 windows 7 (32 bit)

  PCI\VEN_8086 & DEV_2997 & SUBSYS_2801103C & REV_02
  PCI\VEN_8086 & DEV_2997 & SUBSYS_2801103C
  PCI\VEN_8086 & DEV_2997 & CC_070002
  PCI\VEN_8086 & DEV_2997 & CC_0700

  and

  PCI\VEN_8086 & DEV_2994 & SUBSYS_2801103C & REV_02
  PCI\VEN_8086 & DEV_2994 & SUBSYS_2801103C
  PCI\VEN_8086 & DEV_2994 & CC_078000
  PCI\VEN_8086 & DEV_2994 & CC_0780

  Experts in the House should please come to my rescue.

  I just upgraded my Hp DC7700. I was able to get all the drivers except for SERIAL PORT PCI and PCI SIMPLE COMMUNICATIONS CONTROLLER missing. above are the two missing pilots hardware ID

  Hello:

  There is no W7 drivers for these devices.  You must use the Vista drivers and if auto installation does not work, you will need to install the drivers manually by navigating to the folder of the driver that was created when you ran the file from the device in the Device Manager (browse my computer for driver software).

  This package contains the driver Intel Host Embedded Controller Interface (HECI) for access to Active Management Technology (AMT) initiative of the Intel Digital Office for rated desktop models and operating systems.

  FTP://ftp.HP.com/pub/SoftPaq/sp34501-35000/sp34743.exe

  This package contains the Intel (LMS) Local Management Service and Serial - over - LAN (SOL) support for the technology of Directors Active (AMT) under the Initiative of digital office Intel for the supported desktop models and
  operating systems.

  FTP://ftp.HP.com/pub/SoftPaq/sp34501-35000/sp34744.exe

• Serial port PCI and PCI Simple Communications Controller

  Hello!

  My computer OS is Windows 8.1.

  I just shearch something and I found that... I don't have serial Port PCI and PCI Simple Communications Controller. (Unintalled)

  Serial port PCI-> VEN_8086 & DEV_29B7 & SUBSYS_2819103C & REV_02\3 & 21436425 & 0 & 1 b

  Controller PCI Simple Communications-> VEN_8086 & DEV_29B4 & SUBSYS_2819103C & REV_02\3 & 21436425 & 0 & 18

  Sorry for my English. But can anyone help me?, where I can download these files.

  Hello:

  Here are links to the drivers you need...

  Install PCI Simple controller Comms

  http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=3459243&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253Dvc_78668_1%257CswEnvOID%253D4059%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

  Install PCI Serial Port:

  http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=3459243&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253Dvc_78665_1%257CswEnvOID%253D4059%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

• Using PCI and GPIB-Enet drivers set

  We need to use a PCI and Enet GPIB controller at the same time under Solaris 9.

  Is this always the case that it not there no driver unified for the PCI GPIB card and the Ethernet GPIB for Solaris (Solaris 9) controller, as shown in your post on the forum of April 2004 (pfrogers and JoshuaP)?

  If there is no unified driver, is it possible to install two drivers in different directories, and then compile a program that will access both devices having carefully he use different files for header C and libraries, according to what access controller?  It seems to me, the answer will always be no, because your API GPIB function calls will have the same name between the two controllers, so there is no way to specify what (PCI or Enet version) function to call.

  Thank you.

  Hello

  Thank you for your message.  Yes, it's always the case that there is no unified driver for the PCI-GPIB card and controller ENET/GPIB for Solaris 9.  You are also right in your assumption that you will not be able to compile a program that will allow you to access these two drivers in different directories.  I apologize for the inconvinience this may cause you.

  Have a great day!

  Kind regards

  Todd v.

• HP 250 P4T79PT G3: Drivers needed HP 250 G3 peripheral PCI and PCI Simple Communications controller (Windows 7 64-bit)

  Looking for a driver for a HP 250 G3 laptop

  Device PCI and PCI Simple Communications controller drivers

  OS: Windows 7 Home Premium (64-bit)

  Impossible IM find thank you for giving the link.

  Thanks in advance

  Hello:

  When the G3 250 support site returns to the top...

  You need these drivers for devices...

  Realtek card reader driver (under the section storage drivers)

  Driver Intel Management Engine Interface (under section chipset)

• Having problem of PCI and PCI communication serial port

  Hello guys,.

  I have a problem with my serial port PCI and PCI communication, I use Windows 7 64 bit found no solution please help about this and I am very happy to thank

  B.Regards,

  Hussain SF

  Hi Hussain SF,

  Thanks for posting your query on the Microsoft Community.

  I imagine the inconvenience that you are experiencing and will certainly help you in the right direction to solve the problem. However, I would be grateful if you could answer a few questions to refine the question in order to provide you with better assistance.

  1. You get no matter what error code/message when connecting to the serial port PCI?
  2. What is the brand and model of the computer/motherboard?
  3. What card has been inserted in the PCI slot?

  PCI stands for Peripheral Component Interconnect. It's an industry standard bus to connect devices to a computer.

  A serial port is a serial communication physical through transfers of information inside or outside a bit at a time. The term "serial port" usually identifies hardware more or less conforms to the RS-232 standard, designed to interface with a modem or a similar communication device. The serial port used to be widely used to connect to a variety of devices external and is essentially a two-way communication port. There are still devices using a serial port connection. These are often marked as RS232 and would include devices such as TELEVISION receiver cable boxes.

  The PCI of Simple Communications controller is a generic label given by Windows for PCI cards installed in a PC when the drivers for the device are not installed.

  You probably received this error because you have not installed the driver for your PCI device.

  If your computer came with a motherboard driver disc, put the CD in and install the chipset drivers from Device Manager browse the CD. This would update the drivers for those devices.

  Steps to follow:

  a. right click on the entry in the Device Manager and select Properties.

  b. in the driver tab updated some drivers.

  c. Select Browse my computer for driver software.

  d. click on browse and look for DVD player option.

  e. follow the instructions on the screen and restart the computer after installing the drivers.

  If you don't have the motherboard drivers CD then please download and install the drivers for the chipset of the manufacturer's Web site and see if it helps.

  Get back to us with all the information and results of proposed suggestion. We will be happy to help you.

  Kind regards

• series PCI and ocy port driver easy serial port can not get driver Windows 7 Professional

  series PCI and ocy port driver easy serial port can not get driver Windows 7 Professional

  Hi Louis,.

  What is the brand and model of your computer?

  You can visit the computer manufacturer and try to install the latest version of the Chipset drivers.

  Also try to use Windows Update to update the drivers and check if it helps.

  Automatically get recommended drivers and updates for your hardware

  You can also get in contact with the support of computer manufacturer for assistance.

  Hope the helps of information. Let us know if you need help with Windows related issues. We will be happy to help you.

• communication between master blocking and blocking fowarding sensor sensor

  1. how the communication between the master sensor blocking and blocking fowarding sensor take place?

  RDEP or SSL or SSH? Which one?

  Forwarding of blocking sensors will use RDEP more 443 (https) to communicate with the master blocking sensor.

  To ensure that the sensor of blocking of the Master to allow connections from sensors transfer blocking under the hosts permitted configuration section.

  Here's a link for how to do this with VEI:

  http://www.Cisco.com/univercd/CC/TD/doc/product/iaabu/csids/csids10/idmiev/swchap3.htm#32776

  Hope this helps,

  Peter

• Bridge ACER 486 PCI and PCI to ISA

  I have this problem with my computer .i sorts unstall window 7 .but I can't. I got this message...

  The following problems prevent Windows to proceed with the upgrade. Cancel the upgrade, complete each task and restart the upgrade pour continue.

  • Windows must be restarted so that the necessary changes to system files can be carried out before continuing.

  The upgrade of Windows will affect the following programs or devices:

  These devices may not work properly after the upgrade. Before the upgrade, we recommend that you update the drivers for those devices. Cancel the upgrade, open the control panel and search for "update device drivers" or go to the website of the manufacturer of the device to search for updated drivers.
  • System devices: bridge ACER 486 PCI and PCI to ISA

  Hello

  Please select your language from the drop-down menu above to post your question in the language of your choice. The forum in which you've posted is for English only. If you can't find your language above, support for additional international sites options are by following the link below:

  http://support.Microsoft.com/common/international.aspx

  Hope this information helps.

• problem with PCI and PCI express

  Hi people

  I have a problem with my VDI.

  some of my needs of clients to access the PCI and PCI Express slots so that they can fix some PCI card on them and program them

  VMware VIEW can send ports to the VDI?

  do I have to use local mode for this scenerio?

  Please help me

  1. No, not that I know of.

  2. you need not any material to make basic 3D rendering, just turn on the pools.

  Check out this blogpost for heavier applications like AutoDesk 3D:

  http://www.simonlong.co.uk/blog/2012/10/25/VMware-view-3D-gaming-experience/

  Linjo

• PCI-6229 60 Hz noise and drift voltage

  I'm having some trouble with an acquisition of data PCI-6229, connected via a CB-68LP.  I'm under Labview8.6.1.

  The problem is with all the analog inputs. There seems to be a kind of noise in the signal, and I can't determine a reason for this. As it is, I have nothing plugged to the computer other than the CB-68LP.  This block of connection and data acquisition have been know (in the month) to function properly.

  The problem is that any signal seems to have a loud noise (1V_pp @ 60 Hz) above it.  So if I check playback on an analog channel of entry without any link with there will simply be a sine wave a 1Vpp from 60 Hz.  In addition, the sine wave slips a lot (a DC offset), usually to settle about us - 6V.   I just can not get to a good reason for this.  The input will be read in another signal (the same DAQ card or even an external function generator) and reading will look just as (InputSignal + 60 Hz noise + offset CC).

  I run the diagnostic tool (version 2.0) and everything seemed to have passed this test, but I don't know if that means anything.  Essentially, the jury seems to work, but there is a signal from noise important along the way.   I have a hard time thinking that it could be the result of a link between the acquisition of data and the connection block.

  I have everything set up in differential mode, and I'm pretty confident in the wiring between the block and the Library to which the block is attached.

  I've included what labview bed AI0 when 1. nothing is attached 2.  5.75V_pp @ 360 Hz square wave came.  I have also included the results of the diagnostic test.

  See you soon,.

  -ben

  It's awesome Ben,

  If you have problems of noise in the future the article following the Developer area has really good information, cordially.

  Wiring and considerations of noise for analog signals

  Good luck with your application.

  Scott M.

• DAQ USB-6008 will be able to power and record voltage for UMS T5 blood pressure at the same time?

  I would use my NI USB-6008 to power my blood pressure monitor UMS T5 (http://www.ums-muc.de/en/products/tensiometer/t5.html) but also to take readings of it, but I don't know if it's possible to do it properly. The power supply for the instrument can be as low as 5V, I can easily get the dedicated + 5V channel. I'm able to feed the instrument and connect it to an analog input on the 6008 and measure a voltage in differential mode. However, when you read the documentation of support for the instrument, I find the following:

  "Potential pitfalls of data acquisition: the pressure transducer is configured in a full Wheatstone bridge, the input voltage and mV signal output can be connected to the same reference (mass)." Therefore, the mV output signal can be measured using a differential voltage measurement. Therefore, do not make an asymmetric measure of pressure transducer mV output. "(http://www.decagon.com/assets/Uploads/MeasuringUMSTensiometerswithnon-UMSControlandDataAcquisitionSystems.pdf)

  My understanding is that the 6008 can take a differential measure if I attach the signal '+' and the signal "-" to the analog inputs of positive and negative terminals. However, it seems that all the ports of ground on the 6008 are grounded to the same reference, which would make my measure of invalid tension according to the above paragraph. So my real question is: if I try to record the voltage with one of the analog inputs on the 6008 in this way, is the valid measurement? Or I need to find a separate power supply, with a different reference field to ensure that the measure is accurate?

  The technical details of this device is very poor. The manual is not much better. Companies that want to sell scientific equipment should publish decent cards or get out of business.

  In section 3.4.3 General requirements the device is described as a "bridge not amplified circuit.  This information along with the impedance of the bridge should be in the specifications, because it is essential to apply the device under any circumstances other than the nominal behavior in 10.6 V.

  The answer to your question is:

  You can use it with the box USB-6008.  The 5 V supply will result in output voltages a little less than half (5/10.6) the voltage specified in nominal conditions. You can use the differential input mode on the box USB-6008.  The absolute input voltages will be approximately 2.5 V with the 5 V power supply. This voltage is in the range of the aircraft. The differences are likely to be less than 100 mV. The resolution of the USB-6008 on the + /-1 V is located about 0.5 mV so your resolution of pressure will be about 1% of full scale. The voltage input impedance and termination of the USB-6008 will present a few errors.  These can be in the order of 5 to 10%. I can't predict much better without the missing bridge impedance specification.  These errors should be relatively constant and systematic. A calibration of the whole system - sensor and together hardware DAQ should allow you to compensate for a large part of this error.

  Lynn