ENVY M6 - 1184ca: 8.1 for Windows does not start after the installation of update KB2919355

Updating Windows 8.1 KB2919355 has proved to be extremely problematic for me. When he was released at the beginning of 2014 that I was not able to get installed it with the exception of two occasions, the first being several months ago and the second time, a few days ago. I have constant pain to try to get the update of KB2919355 until recently. What finally got the update installed was opened as administrator command prompt and type the following commands,

DISM/Online/Remove - Package PackageNameackage_for_KB2919355 ~ 31bf3856ad364e35 ~ amd64 ~ ~ 6.3.1.14 

and then

DISM / online/cleanup-image /startcomponentcleanup

So now, the update of KB2919355 has been installed. Only one problem: like the first time I had the installed, Windows Update leave commissioning. As the HP splash screen that normally appears during the startup process appears after about 3 seconds, Windows displays an error Stop, and for a fraction of a second will display SYSTEM_THREAD_EXCEPTION_NOT_HANDLED error, which as I read, is related to the graphics drivers. The thing is, after the cancellation of the update (the computer in Mode safe start put Windows automatically uninstall the update and everything goes well after), then go in and uninstall the graphics driver, restart, reinstall the graphics driver and reboot again, and then reinstall the KB2919355 update, the problem recurs. I also tried to download and to install the new update of firmware for my particular DESIRE machine which was released a few days ago, but which has not helped either.

I'm really stuck. I looked up and down, and I scoured Internet for anything that might help. I need to update KB2919355 be installed because without it, I can't book my free upgrade of Windows 10. This laptop is about 2 years and a half old now, so it fulfills all the prerequisites for Windows 10.

Please do not suggest that I do a Refresh of the system or a system reset, as I have no way to back up my programs, that which some I would not be able to reinstall because I have more drives for some of my programs. Also, I can lose to save him for some of my games.

When people ask me "What's up?", I always say 'the CAP '.

So that seems to have solved the problem that is described in this post here. I followed the suggestion, which was to uninstall the driver, SPDT DuplexSecure (which has something to do with the SCSI devices, I'm not quite sure) using the SPDTinst (download here) and now it seems that Windows has started without crashing after installing the update KB2919355. I'll check my Windows Update history and see if it is there.

Low and behold, a year to be really behind value is ultimately more. I have successfully obtained the update of KB2919355 works on my computer.

Tags: Notebooks

Similar Questions

  • Windows 7 does not start after the installation of updates - sounds familiar!

    Apparently, I have another system that no longer starts after you install an update to Windows 7. New kick computer _ I have to disable the automatic update of windows. Twice I had to restore the system in the first week because he hung up after the installation of updates for windows 7. I have no idea what update is the cause of the problem.

    Essentially, start the screen goes black with the cursor blinking in the upper left corner of the screen. The only way out is to restore the system.

    Does anyone know what update is the culpret? HP support has no idea. Their only solution was to update windows 7 to 'never download an update from windows '. It is a terrible thing to be underestimated solution.

    Here's the resolution...

    I installed all the updates except KB2284742 954430, 973688 and 971033. So I decided to install these 1 4 at a time in the order shown. I installed successfully 228472 and 954430 and 973688 disappeared from the list of available updates. So I installed 971033 and it installed successfully and I was still able to restart.

    My conclusion is that there is a conflict between the first 3 updates when they are installed at the same time.

    Now my system is up to date with all windows updates and I'm able to restart without any problems!

    Close this message.

  • Windows does not start after the installation of Service Pack 3 for Windows XP

    Hey guys I have a question I received this automatic update (Windows Service Pack 3) I am running Windows XP Media Center Version 2002, the problem I have is after installation of the update my computer guard stop and windows not not start, I had to go back to my computer to a safe point (usually before the update) and I say usually because I already tried to install this two update times with the same result.

    I hope you can help me I really need your help, I'm totally distraught and I received the update to install it but I'm afraid to install fearing that my computer will not start.

    Thank you.

    Hi Crickets1,

    1 did you receive an error during the shutdown process?

    I suggest that you refer the below Microsoft article and try the steps mentioned to do before you install Windows XP SP3.

    Steps to take before you install Windows XP Service Pack 3

    http://support.Microsoft.com/kb/950717

    I hope this helps!

    Halima S - Microsoft technical support.

    Visit our Microsoft answers feedback Forum and let us know what you think.

  • Windows does not start after the installation of NVIDIA GeForce FX 5500. Help!

    Before, I had a Sparkle GeForce2 MX400 64 MB AGP Graphics Card with the installed driver. I have not had any problems with him, but I need to upgrade, so I got a NVIDIA Inno3D GeForce FX5500 256 MB 128 bit AGP graphics card. So, the thing is, before I installed the driver for it, the computer was working fine, but of course I can't play games. So I downloaded the driver from NVIDIA (175,19 I think), and I installed it in safe mode to avoid any conflict with my antivirus. The installation is complete, and the system restarted. Everything was going well until after the windows logo (by the way, I'm on Windows XP Pro SP3), when the system crashed all of a sudden. The screen turns off, the unit of the system itself was still on, but it does not. I tried enabling / disabling the NumLock, CapsLock button to check if there is an answer, but I have nothing. I manually turned the computer off, waited for about 3 minutes, the market again, but again, the system crashes after the screen Logo of Windows XP. I started in SafeMode again, uninstalled the NVIDIA driver, restart the system and everything went back to normal. I retried my old 64 MB AGP card and it still works fine. I really need to install the driver to make the most of my 256 MB graphics card. Can anyone help please?
    So far I did the following:
    1. re-installed Windows XP
    2 re-installed the driver NVIDIA about 5 times already.
    3. update all the drivers of my motherboard.
    4. completely removed all traces of NVIDIA using Drive Cleaner and put it back.
    5 installed DirectX 9.0.
    Still, none of them worked. Help!

    Here are my computer specs:
    OS: Windows XP Pro SP3
    Motherboard: ECS 661FX-M rev 1. 0 b
    Processor: Pentium 4 2.4 GHz
    RAM: 768 MB
    HARD drive: 1x80GB IDE slave, 1x20GB IDE Master
    BIOS: Phoenix Tech, LTD 6.00 PG 01/18/2006 v2.2
    Antivirus: Avast free Antivirus v6

    Any help would be appreciated. Thank you! :)

    PS: I know that my computer is really old. But please don't advise me to upgrade the entire computer or something like that. I can't afford to buy right now a new. Thank you.

    Hello

    I suggest to start the computer in safe mode and check if you can start.
    http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/boot_failsafe.mspx?mfr=true

    If you are able to start the computer in safe mode, then go to Device Manager and uninstall the drivers for the graphics card and restart the computer.

    If it boots fine in normal mode and then try to install the latest drivers in normal mode and check if that helps.

    Check if that helps.

  • Windows does not start after the most recent update

    I have 64 bit Vista and Office 2007. There was a group of updates for the latter in February 2011. Something in here is stop Windows at the login screen. Workes mouse and keys stick, but it won't take me to the password screen. Only way to get around it was to go in safe mode and do a system restore to remove the updates. Any suggestions?

    Applications, (Norton and McAfee) are notorious for not not upgrade (or uninstalling) itself.

    [You may want to print these instructions for reference offline. If a step said to reboot, reboot.]

    1. download the Norton Removal Tool, save it to your desktop: ftp://ftp.symantec.com/public/english_us_canada/removal_tools/Norton_Removal_Tool.exe

    2. close all open applications (that is, anything with an icon on the taskbar).

    3. After completing some you have a copy of your handy product key, uninstall all Norton software (including LiveUpdate and everything Norton Add ons) via Control Panel | Programs | Uninstall a program (or Control Panel |) Programs and features, if you are using the classic view).

    4 IMPORTANT! -Online activate Windows Firewall immediately after the restart.

    NB: Now you're "working without a net": no to ANYTHING else online (e.g., navigation, reading e-mail, chat) until you have completed step #7 below!

    5. right click on the file that you saved in step #1 above, and then select run as administrator.  DO TAP not your keyboard until the race ends, then restart.

    6. do a clean install of Norton 360 2011 (using your product ID, if need be) & reboot. CF. http://www.symantec.com/norton/support/kb/web_view.jsp?wv_type=public_web&docurl=20080514162318EN

    NOTE: Do NOT activate or install additional modules of Norton (for example, Norton Anti-Phishing) immediately.

    7. manually and repeatedly run LiveUpdate (Norton) until you get a prompt "no update more".

    8 reset the advanced settings of the IE by http://windows.microsoft.com/en-US/windows7/Reset-Internet-Explorer-settings

    9. open Internet Explorer (32-bit) only to http://support.microsoft.com/kb/971058 [ignore APPLIES to section] & run it in DEFAULT and modes difficulty then AGGRESSIVE. [1]

    10. restart once again & test.

    ~~~~~~~~~~~~~~~~~~~~~~~~
    [1] full Disclosure: the difficulty operating in AGGRESSIVE mode will remove your update history but not list the updates installed in Add/Remove Programs (Windows XP) or installed updates.

    ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

  • Lightroom (CC) on 8.1 64-bit windows does not start after the installation successfully without any messages

    I've updated with my creative cloud abbo cc 2014 Photoshop and Lightroom. The update has installed the new Lightroom in parallel with my lightroom existing 5.71 (64-bit). It still works. I've also updated Photoshop CC 2014 without any problem.

    Lightroom has installed a single link in the programs folder and not link on the desktop. This link is staged to "C:\Program Files\Adobe\Adobe Lightroom\lightroom.exe.

    I am using 8.1 in 64-bit Windows. I uninstalled the new lightroom already and installed again. same result.

    Does anyone have a tip what to do?

    You must completely disconnect Adobe Creative Cloud and reconnect. To disconnect using the procedure in the: connect, disconnect | Creative desktop application Cloud.  Click lightroom in creative cloud and lightroom will launch.

  • computer does not start after the installation of updates

    Just click on the button "installs the update and the computer shuts down."  When the computer turns off automatically, I pushed the power button and now it is frozen the computer in start mode.  What should I do now?  Can I power off and try again (or which will mess up the configuration of the update that he just installed.

    Note: There are 21 updates installed last night without problem; then 1 update again (that set up correctly when I restarted this morning).  After a successful this morning launch, I noticed there was an another update to install, which is what made me at this point.

    Single computer at home (I use my work computer to submit this application).

    Wait awhile and see if, during the initialization of the problem to be solved or not. It is NOT a good idea to unplug the laptop.

    If this does not work, then try to press F8 and choose last known good configration, but you may need to reinstall the update again.

  • Reviews of Ubuntu does not start after the installation of updates

    I have a Windows 10 host and a guest Office Ubuntu 15.10. Ubuntu installs and runs fine until I have install updates, and then it gets so far through the boot sequence, but blocks trying to start the GUI.

    What should I do?

    Hello

    can confirm: after installing the last invited Ubuntu patches of the slaughtered 3.16.0-62 core during startup.

    Latest posts is: failed to start the vmware services.

    logfile VMware stops at the loading HGFS subsystem.

    To access the guest computer resolution: Boot with advanced options (hold SHIFT to start, until the menu loader grub is shown). Now select boot option (!) lower than 3.16.0 - 62.

    With 3.16.0 - 60, the guest operating system will start normally. Reinstallation or reconfiguration of the vmware tools don't fix this behavior. If something seems broken with kernel 3.16.0 - 62

    Any solution with core 3.16.0 - 62?

    Best wishes

  • System does not start after the installation of update (10thFeb10)

    Updates to auto (windows Update) using.  Downloaded automatically update yesterday (10thFeb10) and when I shut my computer down it started to install them - as usuall.  However start my computer than this 11thFeb10 am and he began to run through regestry files when starting up.  Then it is impossible to load windows.  Just went to a blank screen.  Rebooted several times and were able to start it in safe mode.  Tried system restore but the same thing happens.  Obviously there was something to this update that 'changed' my computer and I'm not happy about it!  Also thought that there could be new updates (perhaps to fix the last update) but I can not even Windows Update to open it.  Tried online and he tells me that I have never downloaded updates and that none are available.

    I use Windows Vista Ultimate x 86.  I hope someone can help me!

    Got a response from Ms.  Good all who have this problem - you have an ATI Radeon graphics card?  Driver is causing the conflict.  Uninstall all the stuff ATI goes on ATI web site and install the download of 'single driver '.  Reboot and then you can download and install other fancy programs that come with your graphics card.

  • ITunes does not start after the installation of Windows 10

    ITunes does not start after the installation of Windows 10, 1511 version (OS Build 10586.164). ITunes version 12.3.2.35, 6 GB RAM, Intel i3 @3.3 GHz. Itunes and Ipodserver module will run by Manager jobs, but Itunes does not open. iTunes starts in SafeMode as explained in the link below (hold SHIFT and control on your keyboard while you open iTunes).

    Fix unexpectedly closes or problems of launch in iTunes for Windows - Apple Support

    Solution, according to this link, is:

    If the problem does not occur in Mode safe, remove any third party plug-ins iTunes: solving problems with third party plug-ins - Support Apple iTunes but the link has been archived, and I can't find any plug-ins installed iTunes. Any other ideas?

    For general advice, see troubleshooting problems with iTunes for Windows updates.

    The steps described in the second case are a guide to remove everything related to iTunes and then rebuild what is often a good starting point, unless the symptoms indicate a more specific approach.

    Review the other boxes and other support documents list to the bottom of the page, in case one of them applies.

    More information area has direct links with the current and recent buildings if you have problems to download, must revert to an older version or want to try the version of iTunes for Windows (64-bit-for old video cards) as a workaround for problems with installation or operation, or compatibility with QuickTime software or a third party.

    Backups of your library and device should be affected by these measures but there are links to backup and recovery advice there.

    TT2

  • XP does not start after the installation of avira. Blue screen: STOP: 0 x 00000024 (0 x 00190203, 0 x 87174270, 0xc0000102, 0x00000000)

    Original title: xp does not start after the installation of avira

    I have a HP Slimline s7410
    XP Home Edition SP3
    I had Norton free with Comcast, but since I have no more Comcast became Norton expired. So I uninstalled Norton and installed the free version of Avira, he scanned the computer and it was clean. I went to reboot and now it does not start.
    I have a cd/dvd drive of work.
    I don't have an XP bootable installation CD

    My system worked well until: I installed the free version of Avira

    Whenever I select one on the XP advanced options options menu start, it goes into a boot loop.
    I turn off the auto reboot system failure although it seems only work once, as the next time he's trying to start up it goes into the boot loop.

    Here's what my BSOD looks like:

    Disable or uninstall any anti-virus, disk defragmentation or backup utilities. Check the configuration of your hard drive and check the updated drivers. Run CHKDSK /F to check for hard drive corruption, and then restart your computer.

    Technical information:
    STOP: 0 X 00000024 (0 X 00190203, 0 X 87174270, 0XC0000102, 0X00000000)

    Any help is greatly appreciated! :)

    My first suggestion is to do a system restore at this time point.

    second suggestion is to keep your external drive connected to the pc at all times.  only detach when necessary.   of course, it would be better to install a second hard drive in the computer instead.   in any case, keep your personal files out of the system disk is a wise thing to do.   You can also download and store files for free on the Microsoft Skydrive site.

    third suggestion is to keep your system set upward through executing a check disk and Defrag at least once a month.   Basically, you can open the Explorer and right-click on the drive letter.  then select Properties, and on the Tools tab, you will have the opportunity to run the disk check.  then reboot and do a Defrag.   where this disk check fails, then you will need to run it to the drive via a bootable cd prompt.

    Interestingly, I don't know if the bootable cd that you made you allows to run the disk check.

    so my suggestion is to do a series of tests using your cd bootable your computer works.  see if you can actually run a chkdsk/r at the moment with them.    If Yes, then if your constant worries are having bad sectors on the hard disk, chkdsk/r will identify and mark so windows will jump on them.    in any case, see if your boot at the moment media can run a check disk at all, and let me know.

    fifth proposal is to install "microsoft security essentials" like your anti virus program.  even if you have run ubantu, it is not likely to have been an infected copy.   anti - are most critical virus for windows and not not so much for ubantu or linux is because windows is a system of world class operations.    the people who make the virus deliberately their engineer for the windows operating system.   If, however, ubantu and linux have been just as popular as Windows, virus engineers would make infections for the o.s. too.     Although they no doubt, attacks are more frequent for the windows os.

  • Z600: computer does not start after the installation of the 5 TB SATA drive

    My z600 refurbished does not start after the installation of a SATA of Toshiba 5 to disk.  After removing the drive, the computer starts.  I have my computer too old to handle a 5 TB drive, I something wrong or is the DOA drive?

    Thanks for the info.  I added the GPT to my search and discovered what had to be done in disk management.  Here is a page with step by step instructions and photos.  http://www.howtogeek.com/193669/whats-the-difference-between-GPT-and-MBR-when-partitioning-a-drive/

  • computer does not start after the installation of vista updates.

    computer does not start after the installation of vista updates. Startup Repair is also not working. event name: Startup Repair v2, prob GIS. 1: automatic failover, prob GIS 2: 6.0.6000.16386.6.0.6001.1800, prob 3:6, prob prob 5 and 6 GIS GIS sig, 4:720907: corrupt file, prob GIS 7: 3221226021, 8:3, prob GIS GIS prob 9: repair wrp, prob GIS 10; 2, 0 s version: 6.0.6000.2.0.0.256.1. In addition, none of these advanced recovery options seem to work.

    Hello

    Try the steps suggested by David Y post dated November 2, 2010 in the link given below and check if that helps.

    http://social.answers.Microsoft.com/forums/en-us/w7repair/thread/a6071159-db22-4076-b5d8-31f446dbdf32

    Hope that information was useful

  • Windows 7 32 bit does not start after the installation of the need for assistance

    I have an iMac 21.5 inches (mid-2011) with 8 GB Ram, 2 TB SSHD, new HL-DT-ST DVD - RW GA32N and tried to install windows 7 (32 bit) on using Boot Camp Assistant.

    I already downloaded and copied software 4.0.4033.zip Boot Camp here-> https://support.apple.com/kb/DL1630?locale=en_US for my 16 GB Pen Drive MS-DOS (FAT32)

    The installation was successful, and windows 7 loads just fine 1st time, I created UserID and password, settings etc... using the apple keyboard then installed the drivers from apple on this issue of my 16 GB USB key. Seems my Magic Mouse works but my keyboard is not detected

    Then I tried to restart so the changes would come into force, and since then my Windows will not start or run Windows 7

    Now if I start my iMac hold down the Option key, I get Macintosh HDD, windows, recovery 10.11.4 and DVD. If I select Windows or Windows DVD it starts Booting then black screen followed by this Message on the screen «Press a key to boot from the CD or DVD...» »

    If I press any button it starts booting from DVD and gives me the option to install Windows and if I do not press a button some then nothing happens

    Windows does not start a BootCamp HDD and I'm left with no option but to press on the button / stop to stop iMac.

    Fortunately my El Capitan works well, but my Windows will not start. I tried 2 times install windows 7 32 Bit on my BootCamp HDD.

    So any help, I do not understand what am I'm doing wrong, I would be really grateful if someone who knew bootcamp can guide me so that I can run Windows OSX on my iMac.

    Thanks in advance.

    Remove the DVD, boot in OSX and after the release of the following Terminal commands?

    diskutil list

    Cs diskutil list

    sudo TPG - vv - r see the/dev/disk0

    sudo fdisk/dev/disk0

    The "sudo" commands will prompt to enter your password, and there do not appear to come back. You can also see caution against improper use 'sudo' and the potential loss of data due to an "abuse" of the order.

  • Windows does not start after the update...

    Hope someone can help with this,

    I just installed the update sp1 for my computer for Windows Vista Premium Home dir all installed with no problems, but when I restarted my pc, Windows wouldn't start. The only thing that is on display is a black screen with Windows Error Recovery on top, then he said "Windows does not start. A recent hardware or software change might be the cause. I tried to restart it in different ways, but nothing. Then he said: I have to insert my OS drive to try to fix, but that's not even start. Everyone knows about this problem? This has happened right after that I installed the update...

    L.Butler,
    Are you able to boot from your Vista DVD or recovery partion and run the Startup Repair tool?  If you do not have a Vista disc so make sure that your computer is configured to boot from the CD drive before booting from the hard drive.  Once you start with support for Vista select the "Repair your computer" option and first run "Startup Repair".  If that is not correct the problem then boot with Vista support and select the option "System Restore" and choose a date prior to the update install.
    Once you are able to boot normally again, then I suggest that you are looking for virus\malware.  SP1 was released in April 2008.  So if you install earlier means there may be other problems on your system.  If you have a backup of your current personal data then I recommend to do a clean restore to install\factory.  Then immediately install antivirus software, and then do all Windows updates before installing other software. Mike - Engineer Support Microsoft Answers
    Visit our Microsoft answers feedback Forum and let us know what you think.

Maybe you are looking for

  • Disable the notification of El Capitan?

    Hello. From time to time a notification on the Apple store appears on my screen (in front of what I'm working on) asking me to upgrade to OS X El Capitan. I am able to click on 'no' and get rid of him, but I would like to stop from popping up in tota

  • I upgraded my Firefox today (February 29) at lunch and now firefox don't even started! ?? Help please!

    I have a huawei ideos s7 and installed Firefox in December. Updated Firefox in January (I think) and it worked fine!Today I've updated again and now Firefox launches but immediately closes down.

  • Digitization of shortcuts - how to remove or change the

    I'm having the same problem; I have installation shortcuts for my tax years and now I have a ton and I would like to delete the old shortcuts scan; How do you do that?  If register a new tax in 2016, but I want to shorten my list shortcut to I'm not

  • Read out loud does not work

    I have 10 computers Windows and I got DC Acrobat from Adobe reader, where I used the read aloud feature much.  He worked for a long time until that one day all of a sudden it stopped working.  I can set the read-aloud, then click on play and it acts

  • Backup Oracle using AIX cmds

    Hi all I need a clarification about the Oracle DB hope that you guys can shed some light on my question. One of my clients wants to take backup of oracle with AIX - OS commands (file oradata) data file path, when the database is running, butdatabase