Epson printer WF-2510 with wireless-"printer not connected."

Similar Questions

• My laptop Sony VAIO with Vista will not connect and stay connected to my wireless internet.

  My laptop Sony VAIO with Vista will not connect and stay connected to my wireless internet.  All other laptops in the House are perfectly.  Internet disconnects, says local only, then reconnects constantly making internet hard work.

  Hi Tinkerbellfancolorado,

  1. When is this last work fine?
  2. Do you receive an error message or error codes?
  3. Recent changes on the computer?

  There could be several causes for this problem.

  Try starting with these methods.

  Method 1

  Step 1

  1. Open Network Diagnostics by right-clicking the network icon in the notification area, and then click diagnose and repair.
  2. Make sure that all cables are connected (for example, make sure that your modem is connected to a working jack or cable phone connection, either directly or through a router).
  3. Reset your modem and router. Remove the power cord from the modem or router, wait at least 10 seconds, then plug in the modem and/or router back.

  Step 2

  Another reason may be windows disable your network adapter to save power. Turn off the power saving option in the properties of the network (wired network only cards) card:

  1. Open network connections by clicking the Start button, clicking Control Panel, clicking network and Internet, click network and sharing Center, and then clicking manage network connections.
  2. Right-click on the connection and then click Properties. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
  3. On the Networking tab, click Configure.
  4. On the power management tab, clear the allow the computer to turn off this device to save power option, and then click OK.

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-Internet-connection-problems

  Method 2

  Temporarily disable the firewall, and check the status.

  NOTE: To re-enable the firewall after check you the status. If you are connected to the Internet or a network during the time that your /firewall antivirus software is disabled, your computer is vulnerable to attacks.

  http://Windows.Microsoft.com/en-us/Windows-Vista/turn-Windows-Firewall-on-or-off

  Hope that was heloful.

  Bindu S - Microsoft Support
  Visit our Microsoft answers feedback Forum and let us know what you think

• After these recent MS Update, Wireless will not connect XP PRO Dell Inspiron 510 M

  After a recent Update MS, my wireless is not connecting to my home network.

  I've set up as a network secured using WEP.  I checked that the key/password is correct.  He gets in that the acquisition of the IP address, & goes no further.

  I downloaded what I believe to be the latest driver for the Intel Pro/Wireless LAN 2100 3 device has.

  Deleted & reinstalled the device (network connections now watch as Wireless connection 3..)

  MS security Esentials finds no viruses, Defender detects no problem either.

  You b uninstall Norton Security Suite AND THEN (b) download/run the Norton removal tool [1] & restart (c) BEFORE you installed MSE?

  Note: most Windows XP computers came with a Norton or McAfee free trial pre-installed. When you perform a clean installation of Windows XP by using the disks that came with the computer or the hidden restore partition, the free trialware is reinstalled (but invalid). You MUST (a) uninstall the free-trial version AND THEN (b) download/run the appropriate removal tool & restart (c) PRIOR to installation of a legitimate antivirus application (for example, Norton Security Suite freebie) AND BEFORE install any update of Windows (including the Service Packs & IE8).

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Additional references may include:

  Checklist for installation of Microsoft Security Essentials
  http://answers.Microsoft.com/thread/bf757e6a-E320-4a67-92bc-767e6acb26c4

  Can I install Microsoft Security Essentials [or any other anti-virus/anti-spyware application] to clean my already infected computer?
  http://answers.Microsoft.com/thread/87058857-D181-4019-a723-efd9a49d9275

  ==================================================================
  [1] ftp://ftp.symantec.com/public/english_us_canada/removal_tools/Norton_Removal_Tool.exe

• New Inspiron 11 3000 Wireless does not connect

  I bought a new Dell Inspiron 3000 11 for my wife... but the wireless is not connecting to my router to uverse AT & T. I tried all possible security options including zero with open system to see if I could force it to work. Basically, it says "cannot connect to this network.  I have also to install a hotspot on my phone and that really worked. So I got a bit confused... what could be the possible cause?

  SVTG #8HW7732

  output from netsh etc.:

  SSID 4: 2WIRE108E
  Network type: Infrastructure
  Authentication: WPA2-Personal
  Encryption: CCMP

  Wireless LAN settings
  ---------------------
  View networks blocked in the list of visible networks: No.

  Summary information wireless system

  SSID 4: 2WIRE108E
  Network type: Infrastructure
  Authentication: WPA2-Personal
  Encryption: CCMP
  BSSID 1: 64:0f:28:97:b9:d9
  Signal: 100%
  Radio type: 802.11 g
  Channel: 10
  Basic rates (Mbit/s): 1 2 5.5 11
  Other rates (Mbps): 6 9 12 18 24 36 48 54

  1 interface on the system are:

  Name: Wi - Fi
  Description: Dell Wireless 802.11b/g/n 1707 (2.4 GHZ)
  GUID: fe1986f2-3e98-4f55-85e1-2f524d1106a0
  Physical address: 4 c: bb:58:3 b: 58:54
  State: disconnected

  Welcomed the network status: not available

  Wi - Fi wireless LAN adapter:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Dell Wireless 802.11b/g/n 1707 (2.4 GHZ)
  Physical address.... : 4C-BB-58-3B-58-54
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes

  nterface name: Wi - Fi

  Driver: Dell Wireless 802.11b/g/n 1707 (2.4 GHZ)
  Seller: Atheros Communications Inc.
  Supplier: Atheros Communications Inc.
  Date: 06/03/2014
  Version: 10.0.0.287
  INF file: C:\Windows\INF\oem63.inf
  Files: total 2
  C:\Windows\system32\DRIVERS\athwbx.sys
  C:\Windows\system32\drivers\vwifibus.sys
  Type: Wi - Fi Native Driver
  Radio types supported: 802. 11 b 802.11 g, 802.11n
  FIPS 140-2 mode supported: Yes
  802.11W protection of management framework supported: Yes
  Hosted network supported: Yes
  Authentication and cipher supported in infrastructure mode:
  Open any
  Open WEP 40 bit
  Open WEP 104 bits
  WEP open
  WPA-Enterprise TKIP
  WPA-Personal TKIP
  WPA2-Enterprise TKIP
  TKIP-WPA2-Personal
  Defined provider TKIP
  WPA2-Enterprise provider defined
  Defined provider defined provider
  CCMP WPA-Enterprise
  CCMP WPA-Personal
  WPA2-Enterprise CCMP
  Defined provider CCMP
  WPA2-Enterprise provider defined
  Defined provider defined provider
  WPA2-Personal CCMP
  Defined provider defined provider
  Authentication and cipher supported in ad - hoc mode:
  Open any
  Open WEP 40 bit
  Open WEP 104 bits
  WEP open
  WPA2-Personal CCMP
  Defined provider defined provider
  IHV service present: Yes
  HSI YES adapter: [00 7f 03], type: [00]
  IHV extensibility DLL path: C:\Windows\system32\athihvs.dll
  Extensibility HSI UI ClSID: {4a31b2f3-8714-4236-8b6f-5ba745a04ab7}
  Diagnosis HSI CLSID: {00000000-0000-0000-0000-000000000000}

  ChuckFarah,

  Try using the recommended wireless router settings, I use channel 11. If it works, then try it with WPA/WPA2 mixed mode and see if it connects.

  In network and sharing Center, you see a LAN?

  What program anti-virus and firewall are you using?

  Can you run REMOVE YOUR PRODUCT ID and the OWNER UNREGISTERED research information system and publish the information here.

  Rick

• Photosmart more B210b: printer not connecting to wireless network

  I try to install the printer, which has worked before with a different wireless router. I can't connect to the network, even if the print network configuration page says PASS and YES at all the right place with this new router (DB of Belkin Wireless Router N600DB).  When I connect to the router, the printer does not appear in the list of connected devices, but the printed page says it IS connected (has assigned IP address192.168.1.100 on the page). When I try to install the device and connect it to the laptop computer, the IP address is not recognized.

  Both devices are in the same network (belkin.b2.c)

  I've completely disabled the firewall, I install it, both in the protection antivirus software, windows AND router, have revived all 3 devices (printer, router and laptop), but still unable to connect.

  I'll be very grateful for your help.

  JorgeAV wrote:

  Thank you Dragon-fur

  I have a problem with your suggestion and a question.

  First problem: I can't change the SSID name or to change other settings of the printer because I can not connect at all.

  The question is, I see my router dashboard that the Pool of IP address of departure is 192.168. 2.2 and the Pool of IP address is 192.168. 2.200 now, IP address, I can see the printer is 192.168. 1.100 as you can see, the range is different. This could be a problem?

  Comment

  The printer is on a different subnet from the rest of your network.  Yes, it's a problem.

  The printer and the router - and indeed, the rest of the network - these must all be on the same subnet.  Any network - but they are to be on the same.

  For example:

  It is not important whether you choose 192.168.1.1 for your gateway router

  OR

  whether you choose 192.168.2.1 for your gateway router

  The rest of your computers, printers and devices must be on the same network of "sub" as the gateway router.

  You can try changing the IP of the printer on the printer control panel if you can't connect with EWS (built-in web server).  Push the printer over subnet 2.

  Maybe give printer IP address: 192.168.2.226

  Click on the button the printer wireless...

  Click on the thumbs-up Kudos to say thank you!

  And... Click on accept as Solution when my answer provides a fix or a workaround!

  I am happy to provide assistance on behalf of HP. I do not work for HP.

• printer wireless HP not connected to the computer

  My son tried hang our laptop wireless, with no result, since then the printer says not connected to the computer.

  Hi sharryn1940,

  In addition to Michael post, you can also find some good information at the following link:

  http://Windows.Microsoft.com/en-us/Windows7/install-a-printer-on-a-home-network

  I hope this helps!

  Debra
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Network printer not connecting not after Windows update.

  Vista.  Network printer does not connect after an automatic update of windows unknown.  However, requested document printing to a printer wireless unselected, connected to the same network, if the wireless printer is activated.

  Not having received a response to my follow-up question/information, I decided to "Just Do It" on mine.

  I deleted the printer listed as the wireless HP6300 and added back, once again as a network printer.  Not "Uninstall".  (I did on each computer using this printer.  Everything worked perfectly.  Both printers still coexist on the same network and works perfectly.

  As far as I know that something like an update of Windows, change the IP address of the "network printer" at the same IP address as my printer 'Wireless '.  When I deleted and added the HP6300, he returned with the correct IP address.  If anyone has another explanation, I'd be interested to hear.  This problem has also affected two of my friends systems.

  Marcofun

• Deskjet3050A j611g: printer not connected (Yes it is)

  My HP deskjet printer on our network (router Netgear N750) domestic and works fine wirelessly with my PC.  My MacPro Yosemite shows the printer on the network and when I bring the wireless in my browser settings, using the IP address of the printer, it shows the status of connected wireless and I can print the here Network Setup page, but cannot print from any application on my system.  ("The printer is not connected" - and "cannot find the printer")  I uninstalled and reinstalled the printer.  It is the default printer.  I re-installed the printer and the router.  I have spent hours on it, I hope someone can help.

  Hey @YennaB,

  Due to the age of your HP printer not publishes a software package and the downloadable full function driver. Therefore, according to step 5 in my previous post I'll have you manually, download and install the Apple update 3.0 HP driver which includes software and drivers for your HP Deskjet printer. These drivers should work in the same way as the full download of the driver package features of HP.

  You are on the right track if your printer is now deleted through to reset the printing system. If no HP package doesn't show to uninstall, simply skip this step and go to 4-step by step 7.

  Just keep following the steps I have provided and your printer should be in service again shortly.

  Let me know how these steps go for you.

• HP Deskjet 3510: Printer not connected to the Internet after new router purchase.

  After buying a new router, printer does not work. Is not connected to the Internet. I followed the instructions on how to connect but nothing I did helped. Wireless test results show the printer are currently configured with an automatic IP address, I don't know why or how this happened. Also shows that wireless and wireless is working and success to the configuration of the printer, just not connected to the Internet.

  Yes you will need a printer USB cable like this.

  http://www.Amazon.com/AmazonBasics-USB-2-0-cable--male/DP/B00NH11KIK/ref=sr_1_1?ie=UTF8&QID=1458167924&SR=8-1&keywords=printer+USB

• Printer not connected

  I install a HP Office Jet Pro 8600 on a wireless connection to my Mac (latest version of office).  I installed the printer and sometimes can't get the Mac to recognize the printer.  Intermittently, when the printer prints first it hangs on the first 1 percent of employment, then after a while, it prints the page.  The next few pages print ok, but when I go to print the printer is "not connected" again, the wireles light is blue fixed on the printer. If I disconnect the power to the wireless D-Link device, wait one minute then plug back power after a period of time that the printer could appear as connected again. My iPad works fine on the wireless network connection.  All Mac Book my wife does not recognize the printer on the wireless network.  I noticed that the ipv4 addresses are slightly different peripheral oneach, my Mac, thePrinter, my wife Mac Book.  The dfference is the last digit of the ipv4 address.  Previously, I bought a printer that has had the same problem with wireless unti l configuration took everything to the Mac for my 'One on One' store Lemark and a partner that does the job with a magic switch to apple.  The Lexmark printer is now in the Trash because he's stuck with paper so frequently that it opened, before ink cartridges (minimal) have even used, but it is another story.  On two printer, on the point of post appointment. Help, please.

  IP addresses are supposed to be different, it's how the devices are identified by the router.

  D-link routers can have trouble with HP printers.  Make sure that the firmware is updated on your router.

  Finally, we will set an IP address of the printer:

  -Print a the front of the printer Network Setup Page. Note the IP address of the printer.
  -Enter the IP address in a browser to reveal the internal settings of the printer.
  -Choose the network tab, then wireless along the left side, then on the IPv4 tab.
  -On this screen, you want to set a manual IP address. You must assign an IP address outside the range that the router sets automatically (called the DHCP range). Yours is 192.168.0.100 a.199.  We will use 192.168.0.220 for your printer.
  -Apply the subnet 255.255.255.0 (unless you know it's different, if so, use it)
  -Enter the IP of your router (on the Page of the Network Config) for the gateway.
  -Enter for the first DNS 8.8.8.8 and 8.8.4.4 for second DNS.
  -Click 'apply '.

  Now, stop the router and printer, start the router, wait, and then start printing.

  Download and install this: support.apple.com/kb/DL907

  We will restore the print system:

  -Go to System Preferences > print & Scan
  -Right (or control) click in the rectangle listing your printers and select Reset Printing System.
  WARNING - This will remove ALL your printers!
  -Select the sign more to add a printer. Select the default tab on the top of the window. Search for the printer, select it, and wait until the button 'Add' becomes available. Until it clicks.

• HP Office Jet 3830: Printer not connected

  I just installed this new printer, followed all the instructions in the manual and website, downloaded the latest update.

  Checked everything with the Setup Wizard, and he says that everything is ok.

  YET, when I try to print anything, it indicates that the "the printer is not connected"...

  I restarted my computer and also to restart the printer. Nothing has changed...

  I need to help and suggestions to solve this problem.

  Thank you

  Lewis

  Hey @lbriskin,

  Welcome to the Forums of HP Support! I hope you enjoy your stay here.

  I understand that your Macintosh OSX 10.11 computer detects a printer all-in-one Officejet 3830. I can help you with that.

  First of all, let's see if the problem can be related network or Mac related. To do:

  Turn the printer off for a minute.

  While the printer is off, remove the power cord at the back of the router for a minute.

  When the lights came on your router on the printer.

  Now, let's see what the printer think, that is the question. Click on the wireless icon that looks like a radio tower in the Middle at the bottom of the screen.

  The next step depends on the IP address on the printer display.

  • If the IP address starts with 169.254, then the printer does not receive a valid IP address. Click the gear icon and select Wireless Setup Assistant to connect again. If the IP continues first 169.254 then the next step is to contact your internet provider because you have a device that will not receive a valid IP address of the router. If this is the case, then I would suggest calling a device and not a printer. If you say printer they say talk to HP and want to terminate the call.
  • If the IP address starts with 172 the printer is connected to a network of comments. Contact the company that you provided with the router for assistance with deactivation of the feedback network.
  • If the IP address begins with 192.168 or 10 then the printer IP address is fine. The next step would be to determine the issue on the Mac.
  • If the IP address begins with any other number then the network has somewhat changed. I would contact who is now the network for assistance.

  Assuming that the IP starts with 192.168 or 10 the next step would be to reset your printing system. To do:

  On the Mac, click the Apple icon, system preferences and printers and Scanners.

  Hold down the command key and click the picture of the printer on the left side of the screen.

  Click on reset printing system.

  Click on the button "+" in the lower left corner of the screen.

  Select your printer from the list.

  Click on the box to use and select your printer from the list.

  Click on Add.

  If your printer was not in the previous window, it means that there is a setting on the network that prevents the Mac and a printer to communicate. I communicate with the one that is provided with the router and ask them to open all Ports, enable multicast, MAC disable the filtering/MAC cloning and make sure that the router broadcasts a band of 2.4 GHz (gigahertz).

  At this point, you should be able to print. If you are not able to print then please let me know what happened by following these instructions.

  Please let me know if this solves your problem or if you have any other questions. If not, have a great weekend!

  If this solves your problem then please help others to find this post by clicking on accept as Solution on my post.

  If you appreciate my help so please let others know by clicking on the icon below my post thumbs up.

• Install the device driver of printer not connected to the computer

  My printer is too old to connect to my new computer.  I want to "print to a file" and move the file to another computer on which the printer connected (this second computer is not connected to the internet). How can I install device driver on the new computer with no attached printer?

  Hello

  1. What is the brand and model of the printer?

  If you want to move the file to another computer, you can copy the file to the flash drive and move to the other computer, so that you can print the file.

  Check out the links.

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/sag_setup_indirect_printer.mspx?mfr=true

  http://support.Microsoft.com/kb/308028

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  http://support.Microsoft.com/kb/293118

  http://Windows.Microsoft.com/en-us/Windows-XP/help/Setup/move-files-and-settings-to-new-computer

• HP Officejet Pro 8620: HP laptop with Windows 7 not connecting not (either USB or wireless) for HP Officejet Pro 8620

  Have tried reinstalling the printer software, re-start and separately from wireless and USB connections.  Default printer is displayed correctly, print jobs appear in the queue, but does not print... and Yes, there is paper in the tray :-)  Enjoy all the assistance!

  Hello

  Thank you for using the forum. You can try the following:

  Please download and run the HP Print and Scan Doctor (PSDR) tool to diagnose and solve your problem

  http://h20180.www2.HP.com/apps/NAV?h_pagetype=s-926&h_lang=en&h_client=s-h-E016-1&h_keyword=DG-PDU

  Hope that helps.

• Printing from MAC for Deskjet 3050 ALL in one J611n - printer "Not connected" error message

  Good afternoon

  I have problems printing my MAC Book Pro to the printer above.  I said that it is not connected and prints However, when I checked status it shws Networkas "Ready" and the connection as "active"? He doesn't seem to know if it is or isn't?

  I had this problem before on occasions, but now it is a permanent one after upgrading my operating system to 'Maverick '. Now, I have what you call love at first sight bridge on my MAC and don't know what it is for! This has something to do with it? Love at first sight does not appear connected either?

  It's a real pain and I think to get rid of my printer without wire-HELP!

  In addition to the above, I noticed the following error message when I try to print:

  Device status: unknown

  I.D. service: unknown

  I.W Version: unknown

  Serial number: unknown

  Driver version: 2.3.1 HP inkjet driver (why this displays when it's a Deskjet 3050 J611n?)

  Product number: unknown

  I.K no 658

  Watch the device Staus and office as "Unknown".

  3rd update me! In the HP utility is see two printers?  The other has all the full details above with serial numbers and all the info. Watch Staus 'idle' and our 'good '.

  Tracy

  I see that I had 20 veiws and no answer!

  I am new to Mac and not very techno, however I seem to have solved this problem myself.

  I think that after turning to 'Maverick' on my Mac OS Lion, duplicate the printer as 2 showed in 'utility '.

  "I basically deleted that was not'online ' or 'connected '.

  Problem solved!

  Tracy UK

  TracyUK wrote:

  Good afternoon

  I have problems printing my MAC Book Pro to the printer above.  I said that it is not connected and prints However, when I checked status it shws Networkas "Ready" and the connection as "active"? He doesn't seem to know if it is or isn't?

  I had this problem before on occasions, but now it is a permanent one after upgrading my operating system to 'Maverick '. Now, I have what you call love at first sight bridge on my MAC and don't know what it is for! This has something to do with it? Love at first sight does not appear connected either?

  It's a real pain and I think to get rid of my printer without wire-HELP!

  In addition to the above, I noticed the following error message when I try to print:

  Device status: unknown

  I.D. service: unknown

  I.W Version: unknown

  Serial number: unknown

  Driver version: 2.3.1 HP inkjet driver (why this displays when it's a Deskjet 3050 J611n?)

  Product number: unknown

  I.K no 658

  Watch the device Staus and office as "Unknown".

  3rd update me! In the HP utility is see two printers?  The other has all the full details above with serial numbers and all the info. Watch Staus 'idle' and our 'good '.

  Tracy

• Photosmart D7460 with wireless does not work with Win. 7 ultimate connected to the router

  I have a desktop HP upgrade to Windows 7 Ultimate and the new HP printer driver has been downloaded and installed. It seems to print via the server message/controller but is never to the printer or to a file if this opton is selected.  I have also a laptop on group residential network running home premium 7 and same driver.  It works very well to the same printer.  The printer is connected to the wireless router as it is the laptop.  The office is connected to the router.  Any suggestions appreciated that I'm obviously above my head.

  Thank you

  Jackie Draffen

  NO I haven't installed upgrading to windows7 after problems with her 7 installed.  I think it worked a little but only showed 3 ink levels and other problems