Equipped with a network card

RN006uc #aba is the part number it does not show one name other than HP. I need to know the manufacture of the ethernet to connect it's built on the motherboard. Windows XP did not find the drivers for my ethernet. I just need to know what driver should I download. HP would not talk to me without charging $ 45.00. Just need to know what brand of eithernet on board I have on this machine.

Hello:

According to the product # to your PC, you have a HP dx5150 small Form Factor PC

Here is the link to the ethernet driver, you need to know.

http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=447469&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253Dir_68185_1%257CswEnvOID%253D1093%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

Tags: HP Desktops

Similar Questions

  • Error code 797: connection is not available because there is a problem with your network card or modem

    I have a Windows 7 laptop. I use broadband (DSL) to connect to the internet. Lately, I have an error with the code 797. It says connection is not available because there is a problem with your modem or network card. I have a Sony Vaio e series laptop.

    Hi Muffakham,

    Thanks for posting your question in the Microsoft Community forums.

    I see from the description of the problem that you are unable to connect to the Internet and receive "Error Code 797 connection is not available because there is a problem with your network card or modem".

    I imagine the inconvenience that you are experiencing. We are here to help and guide you in the right direction.

    To provide the proper resolution, that I would need more information on your side.
    Did you the latest changes on the computer before this problem?

    This problem may occur because of damaged or incompatible, drivers connection settings incorrect network, hardware or software problems and missing updates.

    Method 1:
    I suggest you try the procedure described in the article and see if it helps.

    How can I troubleshoot network card?
    Method 2:
    If the problem is not resolved, I suggest you try the procedure described in the article and see if it helps.

    Windows wireless and wired network connection problems
    http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

    Check out the link for more information.

    Let us know the status of the issue after you perform the troubleshooting steps. If you need information about the problem with the connection to the Internet or get help, I'll be happy to help you. We, at tender Microsoft to excellence.
  • When I try to establish a wifi connection, it shows that the problem with the network card is not fixed. How can I solve this problem?

    When I try to establish a wifi connection, it shows that the problem with the network card is not fixed. How can I solve this problem?

    Hello

    Thank you for writing to Microsoft Communities.

    Until we start troubleshooting on this issue please provides us additional information by answering a few questions, this will help us better solutions to the problems.

    1. What is the full error message do you get?

    2. are - that you be able to access or connect to the Internet via wired?

    3 have there been recent changes to the computer before the show?

    Please go ahead and follow the steps mentioned and later a update on the State of the question.

    Method 1:
    Try to run the network troubleshooters. Check if it enumerates and helps resolve the errors.
    http://Windows.Microsoft.com/en-us/Windows7/open-networking-troubleshooters

    Method 2: If the problem persists, try to follow the steps from the link.

    In the Windows wireless network connection problems:
    http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

    Check this link for more information:

    How can I troubleshoot network card? http://Windows.Microsoft.com/en-us/Windows7/fix-network-adapter-problems

    Why can't I connect to the Internet?
    http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-the-Internet

    Please follow these recommended steps and post if you still experience the problem.

  • How to configure a VM with multiple network cards to see Agent?

    How to configure a VM with multiple network cards to see Agent?

    We can archive this requirement by configuring the subnet used view Agent.

    The subnet determines which view address of Network Agent provides the server instance to connect to view for the client protocol connections. The view on VM officer has more than one NIC

    Follow the procedure below:

    on a display Agent installed VM,

    * Recording of VM session.

    * RUN--> type regedit or type regedit.exe at the command prompt

    * Create a registry entry to configure the subnet.

    For example: is HKLM\Software\VMware, Inc. \VMware VDM\Node Manager\subnet = n.n.n.n/m type - REG_SZ.

    In this example, n.n.n.n is the TCP/IP subnet, and m is the number of bits in the subnet mask.

  • How can I force a virtual computer to use a specific physical network adapter in a system with 2 network cards?

    I have a host with 2 network cards system.   I have a NETWORK card for the host computer to connect to my domain.  I have a virtual machine that is a deployment server Windows running Windows 2008 server.   The second NIC is to come and turn off the host machine and will then go to a CIsco 3550.   I need the server VM to use deployment only the second NETWORK card and does not communicate the 1st network card that the host uses.

    Can someone please help?  I'm new to VMware.   The original virtual machine on an esx server and was then converted to VMware server 2.

    Yes, just run the network on this host Editor as well.

  • WLAN, lan, dmz on esxi with 2 network cards

    Hello

    I'm newbie esxi. What I'm trying to achieve on my esxi server is simple firewall/gw between internet (vmnic1), LAN (vmnix0) and DMZ. I have only physical 2 NICs in my server, DMZ should be "completely collapsed DMZ. I intend to have 1 web server (www, ftp) in the DMZ, 2 LAN and smoothwall acting as firewall servers.

    After reading some pdf files and some forum discussions I've come with an attached 'Networking' design.

    Could you experts please check design and advise me how secure is it and where are the potential pitfalls?

    COS you need to manage your esxi server.

    The following work of wll:

    An Esx3i server with two physical network (Teddy) interfaces

    pNic0 connected to the internet

    pNic1 connected to your local network

    3 vSwitches configured, one for each natachasery and one internal vSwitch (DMZ)

    Comments "Smoothwall" configured with 3 network cards, one for Internet, a local network, and a DMZ.

    Guests in the DMZ must be created with vNic on the DMZ vSwitch.

    SmoothWall manages the firewall and passes the correct port_number, etc. to the ip address in the DMZ.

    Kind regards

    Torben Jungsberg

  • Unable to connect to the internet with the NETWORK card and Windows Millennium Edition.

    Hello

    I turned on my old computer yesterday, who has installed Windows Millennium Edition. At the back of the computer is an Ethernet port which is marked as LIEN ACT. The NIC with this port is Realtek 8139 PCI Fast Internet Adapter. I spend two hours on the Internet configuration and I did and finally got connected, but then, a few hours after, something went wrong and the Internet and the NETWORK card has stopped working! And the card has disappeared from the Device Manager, but he's still showing in network in Control Panel. I opened the computer and I reconnected it to the slot, but it did not help. At the back of the computer next to this port are two LEDs - green indicates the power that lights up when I plug the Internet cable and the other orange indicates actual connection. But now these two LEDs are not indicating something even when I plugged in the cable to the Internet, which comes from my router. In the computer a Dial Up connection PCI is installed too, but I disabled it. I used Dial-Up in 2002. So, I need help.
    But I know that I can connect with this Ethernet card to the Internet because it worked for 3 hours, I've loaded the pages and downloaded programs.
    Please don't point, should I upgrade Windows!
    Thank you.

    Hi friend,
    You can try a Bing search on connectivity to Win ME, I don't know there are still a few old sites that are not taken down you will find a few FAQ on.
    I saw not a ME machine in too many years to count!
    Good luck on your adventure.
    B Eddie

  • HELP Please: problems connecting to Google Chrome or Internet Explorer: think it has to do with my network cards

    My computer works perfectly except that I can't connect to the internet using Google Chrome or Internet Explorer. Internet works fine.  I have another computer that is connected to the same network, and it works fine.  Also my signal strength is optimal. When I try to go on Google Chrome, it says that the web page is unavailable & the reason why is error: 105 (net: ERR_NAME__NOT_RESOLVE) the server is not found.  When I try to use the Internet, I get this message:

    Device is not working properly because Windows cannot load the drivers required for this device (Code 31)
    I've tried everything and looked at other forums. I went into Device Manager and tried to update the driver, but whenever I do it just says that all updates are already made.
    I really feel that my problem has something to do with network cards. When I go to Device Manager and discovered the network adapters 13 different adapters appear. The 1st is Atheros AR5007 802. 11b / g Wireless Adapter and it looks like it works very well but there are 11 different (Microsoft 6to4 adapt #10) (all have different # s, 10,11,12,14,15,16,17,18,20,5,9) there is (NVIDIA nForce Networking Controller)
    I think the problem is with the Microsoft 6to4 adapters because win I right click & then click on PROPERTIES of each adapter says: State of the device, this device is not working properly because windows cannot load the drivers required for this device. (Code 31) So, is to "find solutions", says & when I do that nothing happens, a message flashes on the screen that says: "Could not load driver software" and that windows is looking for information, but nothing ever happens.
    Can some1 please help me! My computer worked fine and both Google Chrome and still worked and then out of the blue it just stoped working. Any information would be very useful

    wisports,
    Thank you for visiting the Microsoft Answers community forum.

    You have found the source of your problems.  You must remove or uninstall, all the cards of 6to4.  Also delete everything that said map Tunnel or card miniport WUN.  Also uninstall or disable, Internet Protocol version 6 (TCP/IPv6) Properties tab on existing network cards.

    Once you have done these things, restart the computer and make sure that the 6to4 adapters does not return.

    Let us know how it works for you.
    Thank you
    Gloria
    Microsoft Answers Support Engineer
    Visit our Microsoft answers feedback Forum and let us know what you think.

  • VMware device with 2 network cards claiming the same IP address with two MAC addresses

    Hello.

    I see messages intermittent my gateway network two MAC addresses associated with a virtual machine running on a 5.5 ESXi host for the same IP address.

    The virtual machine is a MiTel 3300 controller for a VOIP system. the system is configured with two IP addresses, one on the local network and another with a public IP address in the DMZ. In the network configuration of the 3300, I assigned the address LAN IP at 00: 0C: 29:30:B2:B2 and the DMZ IP at 00: 0C: 29:30:B2:BC (Mac for network devices presented by the ESXi host virtual machine).

    On the host, I configured a vSwitch with exclusive access to two physical network adapters on the host machine. The vSwitch is configured with two machine virtual port groups, LAN and DMZ, with access to the physical network interface cards. Tab grouping of groups vSwitch port NIC, I replaced the order of failover of the switch to activate an active NETWORK card only for the Group of LAN ports and the other card NETWORK only for the DMZ port group. (I don't know how the content of the column of networks is determined. Neither is correct for the traffic on the physical switch. If these are configurable, please advise and I'll change the settings). The relevant parameters of vSwitch, groups of ports and VM are distinguished below.

    On the virtual machine itself, through the VMWare host, I assigned 00: 0C: 29:30:B2:B2 for the Group of LAN ports and 00: 0C: 29:30:B2:BC to the DMZ group port (best I can tell, anyway, since the MAC address field annoyingly obscures the last two digits of the MAC address - break if I invert the mapping) (, but all seems OK).

    The goal here is to make sure that MACs of ports vSwitch the 3300 is listening and sending always correspond to the physical ports that are VLAN Tag by the physical switch to ensure the routing. Generally speaking, it seems that what is happening but, intermittently, we cross one-way calls that suggests a problem of routing between us and our SIP trunk provider; coinciding with these incidents, I get an email along the lines of "the security in the network device has detected a conflict of IP address with two or more devices. The period of INVESTIGATION "DMZ. DMZ. DMZ. DMZ' is claimed by the following clients with MAC addresses: ' 00: 0C: 29:30:B2:B2' ' 00: 0C: 29:30:B2:BC'. »

    I did something in the configuration that would lead to this kind of collision intermittent? Have a hacked together a way to do something that could be accomplished in a way that is simpler and more reliable?

    Thanks for any idea that you can offer.

    Kind regards

    J.

    I probably don't fully understand your configuration, but it seems that you are not interested in using the collection of NETWORK adapters in the virtual switch of the VM MiTel 3300.

    If it is correct, why not create two virtual switches, each with a group of port (LAN and DMZ) unique and with a separate connection of (vmnic2 and vmnic1)?

    In general, collection of NETWORK adapters may be used to share traffic between uplinks and ensure that if one of the uplinks connect fails, a virtual machine still has access to the network.

  • Config of respectable with 2 network cards

    Hello community,

    I have virtualized a Windows XP Pro SP3 which had 2 NICs for different network connections 2.

    Sum one could it me if I need also to install 2 network cards on the new Windows 2008 Server std to have the same networks installed in 10 work stations.

    I have used several times with a single network, but never virtualsation with 2.

    I wonder if I have to use 1 or 2 connections IMO and where I have to configure in the workstation.

    Best regards

    DPE_Irel

    TommyFreddy wrote: you must have two NICS and also ensure that all are trigger guard. Network connection VLAN different you adapter.

    @TommyFreddy, what you had to say offered absolutely nothing different, then what Richardson Porto and I together have already said!  For example, I exposed on what Richardson said Porto by adding additional information expressly excluded by him.  If you do not have something to say then what has already been said and then refrain from jumping and parroting what has already been said!

  • serious problem with the network card drivers

    Ok. I've been messing around last night, playing GTA San Andreas on my laptop. I wanted to see what the resolution that I could run in, so I tinker with them a little more. I tried to apply a change and my laptop screen keeps flashing between 'off' black and black 'menu of the game' and I had to manually turn off because nothing has worked. When I rebooted, I found that I had no internet. This happens fairly regularly (my laptop is a bit grumpy and so it the wireless), so I don't think about it. But this morning, when I really need to search for a document, I found that I couldn't connect to the internet - or via my wireless ethernet cable. I think I'm done at the root of the problem, however: when I go to Device Manager, every single "network card" has a yellow exclamation mark next to it. If I double click on one, it says under device status as "this device does not work properly because Windows cannot load the drivers required for the device (code 31)." After seeing this, I was indirectly bothered to download/install the latest drivers for the two most important cards (Intel Pro / wireless 3945ABG and RTL9101 Realtek PCI-E). They said facilities were successful, but after a reboot, I always saw all connections and it has not responded to my ethernet cable.
    If I right-click on one of the cards and choose "update the driver software", then select the new drivers manually, it starts to install it and then says "windows has detected software driver for your device but encountered an error...". This device does not work properly because windows cannot load the drivers required for this device (code 31).

    I don't really know where to go from here (I'll try to update BIOS driver, but I'm skeptical that it will help), and any help at all would be much appreciated. I called HP and they said my warranty was up and wanted me to pay for their "advice".

    The laptop is a HP Pavilion dv6920us.

    Thank you very much!

    Hello

    What system do you currently use?

  • Create multiple virtual machines with 2 network cards

    Hey guys -.

    Been researching some scripts of difference but did not find one who will help me in my situation.

    I'm looking for a script that will allow me to clone model and apply network settings to 2 network cards.

    1 clone Vms + 20 model

    2 Let me send it to a particular lun (using a few LUNS to available)

    3. choose a custom unique specification

    4. apply intellectual property on 2 NICs (primary and backup).

    Any help would be sincerely appreciated.

    Thank you

    Sorry to lose this thread out of my sight.

    What follows is an attempt to meet all the conditions you listed.

    $numberOfVM = 20$baseVMName = "VM"$templateName = "Template"$osCustName = "MyCust"$IPBase1 = "192.168.1."$IPBase2 = "192.168.2."$IPMask = "255.255.255.0"$IPGate1 = "192.168.1.254"$IPGate2 = "192.168.2.254"$IPDns1 = "192.168.1.100"$IPDns2 = "192.168.2.100"
    
    # Target resourcepool$resPool = Get-ResourcePool -Name Resources
    
    # Get the template$template = Get-Template -Name $templateName
    
    # Create a copy of the OS Customisation SpecTry {    Get-OSCustomizationSpec -Name tempOSCust |    Remove-OSCustomizationSpec -Confirm:$false -ErrorAction Stop}Catch {}
    
    $osCust = Get-OSCustomizationSpec -Name $osCustName |     New-OSCustomizationSpec -Name tempOSCust -Type NonPersistent
    
    # Clone the number of requested VM1..$numberOfVm | %{    # Find the datastore with the most free space    $ds = Get-Datastore | Sort-Object -Property FreeSpaceGB -Descending |        Select -First 1
    
        # Update the OS Customisation Spec NIC parts with the IP addresses    Get-OSCustomizationNicMapping -OSCustomizationSpec $osCust |    Set-OSCustomizationNicMapping -Position 1 -IpMode UseStaticIP -IpAddress "$IPBase1$_" `        -SubnetMask $IPMask -DefaultGateway $IPGate1 -Dns $IPDns1 -ErrorAction SilentlyContinue | Out-Null
    
        Get-OSCustomizationNicMapping -OSCustomizationSpec $osCust |    Set-OSCustomizationNicMapping -Position 2 -IpMode UseStaticIP -IpAddress "$IPBase2$_" `        -SubnetMask $IPMask -DefaultGateway $IPGate2 -Dns $IPDns2 -ErrorAction SilentlyContinue | Out-Null
    
        # Create the new VM    New-VM -Name "$baseVMName$_" -Template $template -OSCustomizationSpec $osCust `        -Datastore $ds -ResourcePool $resPool  | Out-Null}
    

    The script will create clones of $numberOfVM of the model. The virtual machines will be created at the root of the bunch, and they will be called VM1, VM2...

    The OSCustomizationSpec needs to exist and must have 2 network cards.

    The script finds the data store with more free space to create each virtual computer.

    Addresses IP of NIC are consecutive, for example on NIC1 you get 192.168.1.1, 192.168.1.2... and so on.

    Let me know if you have any questions.

  • Will VSA works with single NETWORK card

    Hello

    I have a question about the unit of storage in VSphere. As far as my knowledge is concerned, while we initiate the deployment of the VSA Cluster on two or three host scenario, a virtual appliance VSA is installed on each host computer, which automatically creates a HA cluster and creates two standard switches by default. Each VSA appliance has two network cards, one for the front-end server and one for the back-end.

    My question is if I have only one physical NETWORK adapter present on my Esxi hosts, VSA will work correctly? I asked this question to a few friends and they me says that it will work and both the front-end server and the back-end NICS will be connected to a single virtual switch with which the physical NETWORK adapter is connected. I've never tested and I do not have an environment who test him too. Anyone of you can test it for me?

    Thanks in advance.

    Sorry for the confusion, the VSA 1.0 does not work with ESXi having only single-port Teddy.

  • Alcatel and ZTE Firefox OS phones are equipped with a network of locking?

    I intend to buy one of the two new phones of Spain / Poland running Firefox OS and I'm curios to know if they are equipped with a locking system that prevents me to use her in the Romania, or they will come unlocked?

    Thank you!

    I suggest you buy the ZTE OPEN fire fox phone China. Is it possible to use it in Uganda? Do I need to unlock or the carrier may not support it?

  • Help an admin! Earn points with a network card question.

    Hello

    Network interface seems to have gone wrong on one of my systems. Had comcast out watching some packet loss and we have started seeing losses of packages ranging from a computer to the router. Day after his departure, he simply stopped ping anything.

    Stopped by bestbuy today and picked up a new NIC $ 20, but when I went to only install, no go... New PCI card and this computer (Pavilion special edition, but who knows what's really inside) has only these few slots long 3/4-to 1-inch that a card can go in. A video card uses plus a slot I.

    What is this called crack and what is the best source for a cheaper 10/100 card. I don't think I need a 1gig network card.

    Thank you!!

    Park

    I worked for HP.

    Garen,

    Probably you need to use a NIC PCI - E 1 x or PCI-E x 4.  What model of PC you are using? What is your motherboardmodel PC?  Have you tried to update the driver?

Maybe you are looking for