Equium A100-306 - using an LCD TV only

My laptop has a broken LCD and I want to continue to use the computer with my Sony Bravia TV, acting as a monitor.

I connected a VGA cable between the two devices and have not managed to get the computer to display on the TV screen despite pressing all sorts of combos fn/f5. I can see the colors on the LCD broke enough to tell when I'm at the password quickly and can connect with success on the desktop.

I can't, however, recognize the options when right click on at this stage. Sometimes when I press fn + f5 / broken laptop screen is either empty or has a puree of different colors.

According to me, kind of a 'start-up blind', prompted by a user who has the same model can help. Any help would be gladly appreciated.

RDV

Hallo

You use a standard VGA cable without adapter?

If Yes, make sure if you have chosen the appropriate TV input channel. AFAIK for VGA connector there is a channel called VGA or PC.
Check this box!

Also, make sure that the cable is connected before you turn on both devices. Then turn on the TV and finally your laptop.

Tags: Toshiba

Similar Questions

  • How to connect Equium A100-306 to HDTV?

    Hello

    I was wondering if it was possible to connect my Equium A100-306 to my HDTV using a VGA cable component? The laptop has the chipset intel 945g.

    Thank you.

    Hello

    You cannot convert only a RGB (VGA) signal to component (Y-Pr-Pb), since you will need a converter that transforms the signal vga to this component.

    Which means that you also a converter for cable that could be very expensive. But if you've got components that you should be able to display an image on a device that has entry components. Don t think you will be able to run the HD-ready or full HD on a HD TV, since a HD signal requires an HD port on your computer and a disk hard taking supported system with better graphics chip and then a chipset intel.

    Welcome them

  • Information about the life of the battery of Equium A100-306?

    Hello!
    I have a Toshiba Equium A100-306 & am pleased with it.
    Of course, I want to protect my investment & having been, in the past, concerned about battery 'memory', I was happy to find that this machine works with a battery lithium-ion - & everywhere I look I see words to the effect that:

    "There is no memory and no regular bike not needed to extend the life of the battery.

    I also found: a lithium-ion battery provides 300-500 charge/discharge cycles. The battery prefers a partial rather than complete discharge. Frequent full discharges should be avoided when possible. Instead, charge the battery more often or use a larger battery. There is no memory problem when unexpected expenses. »

    Except, that is, Toshiba (citing the manual) say: "at least once a month, run the computer on battery power until the battery is completely discharged, then discharge the battery."
    Then, they suggest "once a week" to ensure maximum capacity.
    You will understand why I am confused? I would really appreciate someone stating the above.
    Thanks for your time. Cheers, Peter.

    Hello

    Perhaps they have not properly updated their textbooks? I Don t know, but is the only thing I can tell you, that new technologies in mobile systems such as yours are very modern and I think toshiba had a cool technology into their machines, so that systems of remain "without worry".

    I suggest you read this article on the type battery that is in your machine so that you can understand the best technology:

    http://en.Wikipedia.org/wiki/Lithium_ion

    Hope I could give you an idea...

    Welcome them

  • Equium A100 - 306 Question on upgrade Vista ModusLink

    Hello

    I bought an Equium A100-306 in November before deploying operations that I'm in the forces and could not be updated before that.

    I just go and discovered that I can't have my Vista upgrade I missed the deadline. I ModusLink E-mail unanswered. I was wondering if anyone has any advice or that you could help me solve this problem.

    I think that I should not miss out on the free update due to circumstances beyond my control. Looking through the documentation I received with my laptop there was no deadline, said that it is only on the internet, the date limit is clearly but I was unable to verify this.

    Thanks for any help.
    Greg

    Hi Greg

    What to say. The overall programme is controlled by the ModusLink Corporation and any misunderstanding, you must try to clarify with them. I think that the end of March was the deadline for the Vista upgrade program.

    Sorry, but you are alone and try to talk with them about the situation as a whole.

  • Equium A100-306 with SuSE 10.1 - ACPI

    Hello

    I have an almost nine Equium A100-306 (4 months) with SuSE 10.1.

    Have you any idea where I could find the support acpi for this model?

    Thank you
    EDINA

    Hello Edina

    If you carefully read the Linux article, you will discover that Linux is not supported for operating system, but there are a few links very useful where you can find information on Linux on Toshiba laptops.

    I'm not fan of Linux and unfortunately not help you but before you wait here to find answers please check can track the pages:

    http://Linux.Toshiba-DME.co.jp/Linux/index.htm
    http://www.Linux-on-laptops.com/
    http://newsletter.toshiba-tro.de/main/index.html

    Good luck!

  • Serious problem with driver i810 Equium A100-306

    I have a new Equium A100-306 and I try to install two different Linux distributions:
    10.1 (x86_64) SUSE and BlueWhite64, but in both cases, I met the same problem:
    When you restart the Xserver, the computer stops responding.

    I used the i810.
    This is not the case with the vesa driver.

    lspci reports:
    00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS/940GML and 945GT Express Memory Controller Hub (rev 03)
    00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS/940GML Express Integrated Graphics Controller (rev 03)
    View 00:02.1 controller: Intel Corporation Mobile 945GM/GMS/940GML Express Integrated Graphics Controller (rev 03)

    Hello flora

    Before you wait here for a long time trial learn more about Toshiba Linux pages:
    http://www.Linux-laptop.NET/Toshiba.html
    http://Linux.Toshiba-DME.co.jp/Linux/index.htm
    http://newsletter.toshiba-tro.de/main/index.html

    Good luck!

  • Equium A100 - 306 PSAABE - cannot start and the error of the BIOS

    I have a Toshiba Equium A100-306, which does not go beyond the BIOS screen. Last thing I did was delete the second partition on the hard drive and the boot configuration Winodws via DVD. Then he stopped display

    If I hit ESC on the post screen, I get a screen that says this: http://i57.photobucket.com/albums/g232/Medabot_Metabee/BIOS_ERR.jpg

    Ive read that theres a method of emergency crisis of flashing, is possible to run it on this laptop?

    Thank you

    Hello

    This looks like a malfunction of the motherboard, you can enter in the setup of the BIOS for example? If Yes, load default settings then save & exit it.

    If you can t get into BIOS try remove the battery and the AC adapter at least an hour. Then connect the two again and try to start your laptop.

    He starts correctly now?

  • Cannot install updates Office on Equium A100-306

    Cannot do the following updates on my laptop Equium A100-306

    Update for Office 2003 (KB919029)
    Update for Office 2003 (KB920813) security
    Update for Office 2003 (KB925251)
    Update for Office 2003 (KB914455) security
    Update for Office 2003 (KB936048) security
    OneNote 2003 Service Pack 3 (SP3)
    Update of security for Microsoft Office 2003 (KB921598)
    Update for Office 2003 (KB954478) security
    Update of security for Microsoft Office 2003 (KB953404)

    What you mean with this? You get an error message? The laptop did a restart?
    Then please give us a little more information.

    I don't know but maybe that updates are already in Office 2003 SP3 Mr. check the!
    Maybe it of enough if you install the last SP for Office visit the Microsoft Web site to download this file.

  • Equium A100-306: screen black TV

    Hello I was wondering if someone could help me, I have a laptop Equium A100 306 and I want to plug into my tv to watch movies that are stored on it.

    It has a SVHS socket on the side and I bought a svhs cable SCART for her and when I connect it to my TV the picture is black and white. Does anyone know how to remedy this? Any help would be greatly appreciated.

    Thank you.

    Have you tested with different channels? I have my reserved channels connect TV SCART. Also check the settings on the television. Maybe you have an option to get the color.

  • Black screen on Equium A100-306 after watching the movie on external projector

    Hello!

    I have a laptop Satellite A100-306 and it worked very well. Yesterday, I plugged in a spotlight and watched the movie.

    Once I finished the movie I have turn it off and disconnected from the projector.
    After a few hours later, I tried to change my cell phone and found that the initial screen of charges until after there is nothing on the screen.

    I was able to go into the BIOS but couldn't go safe mode. I remember I used the key Fn and F5, but nothing comes so any help would be much appreciated.

    While the initial charge up screen I do not think that there is a problem on the screen or the graphics card the toshiba logo at startup.

    Can anyone help to know if tht is a hard drive problem maybe.

    Hmm for me it seems that the display was set ONLY to an external display device (projector, screen, etc.) and, therefore, you are not capable of anything on the internal display of laptops.

    I think you need to connect an external monitor or projector to this laptop second and must try to set display settings default (Mobile only)

    The FN + F5 combination should help you.
    As far as I know the laptop replaces the output of the screen in the following order:

    * Internal display * * (CRT) screen external + internal screen * * (CRT) external display only * TV (s-video output) + internal screen * TV only (output s-video) *.

    So maybe you have chosen the last device (output only s-video)

  • Equium A100-306 beeps at startup

    Hello

    I have an A100-306 which, at startup, beeps for about 30 seconds, then starts up fine and then works perfectly, if I look at the laptop all the ram is recognized and the CPU seems very well, there is no display problem, the only thing that doesn't work is the CD drive doesn t recognize disks but the drive shows on the laptop , but if I remove the CD drive still beeps on startup anyway.

    Any ideas anyone?

    Hello

    The beep code during POST (power on self-test) means that an error has been detected on the motherboard.
    But it of really difficult to say what could be the problem here, you said RAM is recognized correctly hmm try to remove a RAM module and start Notepad using RAM only one in each slot

    All devices are connected to the laptop? If so, unplug everything (all devices) and try again.

  • Equium A100-306: cannot set resolution 1440 x 900 on external monitor

    Has anyone encountered this problem? I searched the web without success and it doesn't seem to be all programs that will force the graphics in this resolution. Is only shown for linux-based systems which have a complex solution for this. I have a new A100-306.
    The maximum power that I get is 1280 x 1024, which is ok but lack just that final freshness.

    I think that the solution will be an update of the video bios but it is an update from the manufacturer and not a processor intel, a? As the machine is new he does not appear to be updated again. If anyone has a solution please post, if not Toshiba please quickly with an updated driver.

    Thank you

    Hello

    I read several candidate here in the forum on different screen resolutions that are not available for the external display.
    Fact is, if no resolution of the screen is not available, then the graphics driver doesn t contain the display resolution in the list. In this case you must use the common screen resolution which is available. But this isn't a problem.

    Furthermore, each screen support a clean resolution. I mean the screen with a resolution which is the best for this view. Then the screen and the image is very clear, and as you said crisp.

    On my screen I can pick several display resolutions, but the best resolution for my monitor 1280 x 800.

  • Can I add a better graphics for Equium A100-306 card?

    As the title suggests it is possible to add a graphics card to an A100 - 306 Equium to better manage the games?

    Thoughts or comments appreciated.

    Thank you

    I can only confirm the information provided by James.
    The notebooks are all just different as the desktop PC and these updates are therefore not possible.
    If you are a hardcore gamer I n t understand why buy you a laptop.
    I m also play with passion and I would recommend buying a desktop computer if you want to play the latest games. The Office supports various devices. You re more flexible with upgrades and especially the parts are cheaper.

  • Can Equium A100 - I use E drive for data backup?

    My Equium A100-27 has a 80 GB hard drive, it is split in the C drive half and drive E.

    I understand that the E drive is used for system recovery purposes, but can I also use it to store data?

    If I use it for how much room must be left free for system data recovery?

    It's old laptop model, and there is no recovery of data stored on the second partition of HARD drive.
    If you can do what you want with this partition, and also use it for backup of data or backup data.

  • Equium A100-306 memory upgrade from 2 x 512 MB to 4 GB for Windows 7 64-bit

    Hello

    I want to upgrade the RAM on my A100-306 to make use of the full capacity of win 7 64 bit. I was looking around, I know that I need PC-4200 (533 MHz) 200 Pin SODIMM modules, but I'm not clear on whether they need to be combined. Ideally, I would like to buy a single 2 GB module now and then take a second in the future. My questions are:

    (1) is it acceptable to have a single 2 GB module?
    (2) can I leave in one of the current 512 GB modules give me 2.5 GB?
    (3) the extent to which the second module must match the first case has been purchased and added at a later date?

    I look forward to the advice.

    Concerning
    If

    Hello

    The A100-306 supports the Mobile Intel® 945GM Express Chipset.
    This chipset supports 4 GB RAM max.
    This means that you can use 2 x 2 GB modules.

    Yes, you can use 512 MB and 2 GB of RAM, it should be possible

    Usually it s recommended to use modules with the same specifications
    I mean that the modules must use the same speed (Mhz) if one of the modules will be slower then the fastest module be pointed down and the two modules would go to lower speed

Maybe you are looking for

  • upgrade memory 2540p

    How many modules memory are there on the 2540p? Of after Crucial, there are two. According to my system, I have 4 GB installed (3.80 GB usable).But when I take the cover on the back, I can only find a single SODIM 2 GB module and on You Tube, they sh

  • Glyph library

    My icons and folders are where they are supposed to be.  However, now when I try to change my icons VI editor shows only a white tree.  I think I deleted a XML file which is supposed to be there. When I tried to sync automatically and manually withou

  • That means the AHCI Mode, Mode RAID & SATA IDE Mode in the BIOS settings means

    That means the AHCI Mode, Mode RAID & SATA IDE Mode in the BIOS settings means My computer is having problems when I bought all first it was from another provider which came as a set overclocked PC up the unit everything needed had to be put in my ca

  • Impossible to update InDesign, U44M1I11, no response from Adobe error message.

    Our IT Department has not been able to solve the problem, the signature and to my account allowed me to update to Photoshop, but not InDesign or Illustrator. No response from Adobe from this date.

  • Files using PNG in Photoshop to create Brush preset for watermark

    How can I talk to a png file in Photoshop and creating a Brush preset with it to use as a logo watermark?Thanks for any help you can give me. I am a bit challenged in this area