Equium L10 will not start

Similar Questions

• Equium A300D will not start.

  My Equium A300D does not start. It just displays 'the file is possibly corrupt. The file header checksum does not match the checksum calculated. Why? What can I do? I have only a few months.

  Have you installed lately new RAM? Its important to the RAM test before use. Or the standard RAM is possibly defective.

  Go to www.memtest.org and run Memtest for a few passes (it is a bootable CD).

  The file system may be damaged, try running CHKDSK from the Recovery Console. http://support.Microsoft.com/kb/314058

  The HARD drive could be faulty, Hitachi DFT is a good HARD drive tester. Run the test advanced to search for bad sectors.

• Equium A60 will not start

  Hi, I am despartely needing help with my A60 equium that won't start. When you turn the button lights up, fan and starting, but then in a few seconds the cutting power. I tried different sources of energy, also just by using ac power and battery just all produce the same results. I had installed a memory chip a few months back and thought it might be that, but when I took it off the laptop has always been the problem.

  Is there that anyone may be able to help me with this problem? Thank you

  TAF

  Hi Michael,

  The first thing that happens when your, press on the power button on your laptop, it's that the CMOS chip (which contains your BIOS) through a pre-deignated POST (Power On Self Test) process that verifies the functions of the material of base components after what the BIOS will be charged which will lead in turn to the operating system itself being started.

  If a failure or a problem occurs during POST and then power on the sequence stops (usually after a series of beeps are emitted that are coded to help the diagnostic process. The actual beep codes are specific to the manufacturer of the CMOS/BIOS chip.

  If you receive no all audible sounds, then it is likely that the problem is very early in the POST process and may indicate a problem with your main card or your electronic internal.

  You can try to remove and and reinstall devices such as RAM memory modules, hard drive, optical drive, etc to see if this corrects the situation, but if not then you will need to take the device to authorized, Service partner who has the diagnostic equipment needed to perform accurate control.

  Kind regards

• Satellite Pro L10 will not start - the LED blinks

  I have a pro l10 phone which, after sutting down as battery not return to life. All I get is 8 flashes on battery led when the button is pressed. It's the same area only, battery only or both.

  It sounds bad
  Generally, the laptop LED flashes as there might be a hardware malfunction.
  The LED provide a microcode and the technician can read this code.
  A common user is not able to read. OK maybe you can read it, but you will not find any description about the meaning of the code.
  That is why it s a good idea to contact the technician in your country

  But as a first step, try this:
  Remove the battery and unplug the AC adapter.
  Wait 20 - 30 minutes and then plug in the battery and plug in the AC adapter.

• Equium L20 will not start properly

  My laptop L20 primer not. A black screen appears "apologize for the inconvenience, but windows did not start successfully.

  Then tells me to highlight a choice of starting up, but when I choose, it moves quickly on a blue screen that I cannot read, then goes back to the same black screen.

  Help! It feels like Groundhog Day.
  Cannot make it work.

  Hi Donna,.

  More simple you take it out of this situation is to reinstall your operating system of the recovey CDs. Unfortunately this won't replace your data (unless you have partioned your hard drive and store your data on a second partition).

  This problem is usually caused by a missing or corrupt system files that prevent Windows from loading. Of course, you can try to recover the situation by using the since the original Microsoft Installation CD Recovery Console if you have one.

  It is also possible that the failure is due to a defective hard drive but it will become apparent when you try to re - install.

  Kind regards

• My Toshiba L10 will not start!

  Hi all

  My Toshiba L10 (3 months) will start not especially when transported from one workplace to another. I have this problem more and more frequently. I'm so worried.

  Could you please tell me if it is an indicator of a serious problem with my computer? How can I solve this problem?

  Thank you very much in advance for your answer.

  Best regards
  Ana

  HI Ana,

  If your laptop is only 3 months old then it is always be covered by your guarantee of origin then I suggest that contact your nearest authorized service center that will be able to deal with your problem.

  If you think that your problem is software partners so please can you give some information about the symptoms that you experience when you try to start your laptop.

  Kind regards

• Equium P200 will not start

  I have a notebook equium P200 and it won't start, it started, then froze when I turned off and then on again, I got was the toshiba logo then the symbol loading then nothing just a black screen. I rebooted and let it go through the analysis in case of errors, but it will still go to a black screen. It is running Vista. The blue disc light that lights up normally when it starts does not illuminate. I don't lose everyhting on it or can it be saved.

  Post edited by: sugajars

  Hello

  Try this:

  -Remove the battery
  -Unplug the power adapter
  -wait 1hout
  -bring the two parties together and try to turn on the device

  I hope that you will be successful if not is not-> the time for service :(

• Equium L10 will not enter OS after recovering with disc A60

  I accidentally restarted my L10 of A60 recovery disc, it seemed to work until I went to reboot my computer and now the screen is just blank and the PC does not boot to windows. I was going to put the L10 recovery disc in and start again until I realized that I can't, all I have is the disk A60.
  Can you help me on this?

  Thank you

  Cara Hayes

  For me it sounds very amazing that you were able to install the recovery on the L10 A60 image. To my knowledge, it is not possible to use different recovery images
  But anyway, it is not unusual that the portable computer cannot enter the operating system if you have used a false image.

  I think that there is not much to do. Either you will start from the recovery CD Toshiba L10 or you will use the original CD of Microsoft Windows.

  If you used the Windows CD, you must also install the Toshiba drivers which you can download from the Toshiba driver page.

• Satellite Pro L10 will not start

  Hi guys,.

  I have a Sat Pro L10 and I have a few problems with it. When I load up, I can enter the BIOS and everything seems fine, however, the date and time does not. I can't ge start beyond that point, it crashes just with a cursor flashing at the top left. The same goes for when I try and boot from CD. When I go out and put the battery back, I get a message saying WARNING CMOS Checksum failed - using the old configuration, F1 to resume or F2 to enter setup. I press F1 and the same again, just a flashing crusor.

  If anyone can help me diagnose this problem and fix it, it would be much more appreciated.

  Best regards
  James

  Hello

  At first read s manual, page 100 as well as page 104. You will find explanations on CMOS Checksum failed.

  To have fully loaded CMOS laptop battery must be powered ON 24 hours.

• Satellite Pro L10 will not start the system

  Hello!

  I have a Toshiba Satellite Pro L10, which won't work for some reason any.

  The last time that I used it, it worked perfectly fine, but now all I get is a black filtered message on "windows starts do not successfully»

  It indicates that the computer is not responding and asked me to choose one of the five options - safe mode, safe mode with network, security mode command, last known configuration, prompt or start windows normally.

  There is also a 30 second countdown if I do nothing the portable samekh automatically.
  It is, none of these things work.

  Everything that happens with any option is to a thought very much time on things, then it goes to a black screen with a time/processing bar downstairs, then when that ends it turns itself off, samekh, mw windows page shows (with f2 and f4/f10? options) and the process is repeated.

  He did about 50 times now and still nothing.
  I tried the command ctrl/alt/del, I tried to turn if off and try again, I even opened the f options but I don't know enough about computers to do more.

  Help, please!

  If possible I would like to get the computer on long enough to verify what documents I have on this subject before I can back up (if necessary) and restore it to the factory settings (as I predicted), or if this is not possible, I do not think that there is a lot to lose in this respect in any case, am prepared to take it all back to factory if necessary. I have all necessary installation CD and manuals to go with.

  hope this makes sense and I gave you all you need to know.

  Thanks, B

  It seems that the laptop is not able to boot the system, but I m not quite sure if it s because of the defective system or HARD drive corruption.
  If it s just a system problem, the installation of the new Windows operating system should help you to get it resolved.

  In case the HARD disk is defective, you need to replace the HARD drive and reinstall the system.

• Equium A60 will not start - get a beep code

  Hello

  This laptop has problems with ATI (even those included on the recovery disk) display drivers. He created a blue screen on a dll file.

  After reading around, I found that it was recommended to upgrade the bios, after going to the appropriate section of the Web site, I downloaded the flash tool from windows for the laptop bios.

  I ran and it opened, returned to the laptop and the screen is blank, a blue ring around the power button is on, but no display.

  I left it for a period of time see if it would to restart or something, but nothing has happened, it would not be the button turn off so I unplugged the power and removed the battery.

  To again turn on the laptop, it only stays on for about 3 seconds then turns off again.
  I get the beep code: short break, Long, short break, beep, beep beep, then it turns off.
  The caps lock and numlock keys are turned on.
  The DVD drive light blinks.

  But other than that, no display etc.
  Ive tried the battery leaving aside for awhile.

  Anyone have any ideas why flash bios toshiba own this would cause? Also what can I do about it? in any case to recover the bios etc via a recovery mode?

  Thanks in advance.

  PSA67E

  Hello

  Well, unfortunately for me it looks like a hardware failure.
  Maybe the motherboard is broken.
  These problems may occur if you use a bad BIOS or the incorrect BIOS update procedure.

  Please check this document FAQ How to upgrade the BIOS:
  IOS http://eu.Computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/FAQ.jsp?z=234&service=eu&from=faq_selection&CFID=B & FID = TRO0000000b07

  Unfortunately if there is something wrong with the hardware you should ask Toshiba service for assistance.

• Satellite Pro L10 will not start - green turns off after 3 seconds

  Hello

  Having a L10 (PSL15E-01J018EN) and when you press the button, the led ON / STANDBY on the front lights up green for about 3 seconds and then past off the coast. It accomplishes this task for the sector or on battery and there is no other life. Anyone know what may be the problem?

  Thank you

  Melv

  Hello Melv

  Remove the battery, connect your laptop to the power adapter only and try to turn on the L10. If this lets wait a few minutes and put the battery in place and watch if the laptop works as usual.

  Please let us know exactly what is happening.

• Somewhere, I messed up my permissions, turn off the computer to see if it helped, now will not start at all. The start bar stops a quarter turn along. I tried in SafeMode as well do. I ' on a Yosemite iMac running.

  Somewhere, I messed up my permissions, turn off the computer to see if it helped, now will not start at all. The start bar stops a quarter turn along. I tried in SafeMode as well do. I ' on a Yosemite iMac running. I can't enter to give more details. Can anyone help? There are a load of work due to deliver to the printing press Monday

  Have you tried to boot from the Partition Recovery and repair then the disc from there, using disk utility?

• G5 will not start. LED light on. Fans before working.

  Early 2005 G5. running 10.5.8.

  G5 will not start. LED light (no flashes not but solid). Fans before working. Rear fans blowing not. Cleaned up the dust. A exploded during a down and will not restart. Any thoughts? Is that a bad diet? What I would do. Thanks for any help. I love this old computer and hope to keep fixed and working.

  Sam

  Some of the fundamental things include the pram/clock battery replacement

  since they may be dead; then with a power failure, sometimes the Mac

  do not restart. Usual power management unit & reset NVRAM/PRAM are

  methods that sometimes also used as a troubleshooting measure.

  • Reset the Mac chip power management: (see SMU)

  http://www.thexlab.com/FAQs/resetpmchip.html

  • How to reset NVRAM-LANDAU on your Mac - Apple Support

  A hard reset can sometimes be used, where the power is disconnected

  the logic board and power removed from grill; Then push the Start button / stop.

  (But maybe not. Several PowerMac computers, I had, some people found this helpful)

  You may also remove and reposition cards and other items

  the inside of the case, to be sure they are connected properly. Be sure to not

  In short anything, due to the static load or residual power in the circuits.

  The hour is late here, so I'm not going offline; If all goes well a battery original or novel, etc.

  can help to put it on again. Also sometimes the power supply has some faulty fans,

  circuits or capacitors, so they can be troublesome to repair or replace.

  Good luck in this case!

• Firefox will not start after update

  Firefox will not start today. I think he had an update yesterday.
  Click it, lift the loading symbol, but never implemented. In Task Manager it is a firefox.exe * 32 running. Have you tried to uninstall, delete Mozilla Firefox folder in Program Files x 86 iti also tried to suppress the appdata profile (after saving the Favorites and passwords). I can't even boot up in firefox safe mode and can not get to start Profile Manager. If I start (7 x 64) of windows in safe mode, I can start firefox. I use Norton Internet Security. I checked the settings of firewall smart and experienced of firefox is still set to allow. I tried starting firefox with smart firewall turned off and firefox still refuses to start
  Renounce top almost ready

  Hello ziggy1, as this can sometimes be caused by a malware active on a system, please run a scan with tools of different security like the free version of malwarebytes, the adwcleaner and the scan to microsoft security.

  Fix Firefox problems caused by malicious software