Error 0x0000007B after return of 10 to win

Similar Questions

• error 0x0000007B after installation in Portege R500 XP OEM recovery CD

  I have a R500 with 64 GB of SSD and preinstalled Vista.
  I try to downgrade from Vista with a R500 XP Pro OEM recovery CD.

  Decompression for the SSDS works fine - but at first start-up of XP Pro, I get a blue screen with an 0x0000007B error message and some tips about the infection by the virus?

  What causes this problem?

  Hello

  To my knowledge the R500 supports a HDD SATA controller and you include the SATA driver in the CD of Win XP using nLite software.

  The SATA driver is part of the Intel Storage Manager that could be found on the European driver Toshiba page or on the page of Intel.

  By the way; Check out this forum and use the search option to find more discussions about the Intel Storage Manager and how to use the nLite and include the SATA drivers.

  Here are enough discussions on this topic.

  See you soon

• Error 0X0000007B (inaccessible boot Device) to start.

  From two days ago, about 8 or 21:00 my computer freezes whenever I clicked on any icon or attempted to open anything. Not even all that normally appears as yahoo messenger and all my other programs popped up. After this has is spent several times I went to safe mode and thought at first maybe it was something with the memory, or maybe the computer was going slowly I went into cleaning disk and deleted files. Then, I went in my add or remove programs and deleted some things more freeing space. After that happened, I tried again and still no luck. Shortly after, I went back to the security mode and attempted a full McAfee scan for viruses. It took 11-12 hours and there is no virus. Then, I went back into safe mode and tried to do a restore of the system for a few days back. I've tried twice and both times a screen popped up error after about 3 or 4 minutes for system restore. After some research I found this means cessation critical object, so I tried a startup repair, it said 0X000000F4 (0XFFFFFA8006881BA0, 0XFFFFFA8006881DD8, 0 X 0000000000000003, 0XFFFFF800022E3540). I tried twice and both times it ended around 124545 887104. That was 1%. Then I went back into safe mode and some more the object of research and discovered that using the F8 key I could try solve the problem. The second, I pressed the button repair he opted for another blue screen this time with 0X0000007B (0XFFFFF98000A069E0, 0XFFFFFFFFC0000034, the last two are all zeros. I learned that it was Inaccessible boot Device. I tried to use my last known configuration after return in safe mode and that did nothing. I then went to my device because Manager that all the time I did research we're talking maybe a driver is not updated. I discovered that my drivers are all updated, but my IR devices has a triangle attention beside him. When I clicked on properties I found it saying: this device does not work properly because Windows cannot load the drivers required for this device. (Code 31). I tried many things, and every time that I have either get a blue screen or my attempt does not work. Please help me, if I can't find a solution, I'll be forced to format my computer and restart my computer life. (email is * address email is removed from the privacy *)

  Hi Killace,

  Step 1

  Try the suggestions in the article below.
  http://support.Microsoft.com/kb/922976

  Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
  322756 (http://support.microsoft.com/kb/322756/) how to back up and restore the registry in Windows

  Step 2

  Uninstall IR device drivers...

  A. Click Start, type devmgmt.msc in the start search box and press on enter.

  B. do the driver right click and choose uninstall.

  C. restart the computer and check if that helps.

  Step 3

  Disconnect all external devices.

  Put your computer in a clean boot.

  The following link has steps showing how to perform the clean boot:

  Note: Please make sure that the computer is configured to start as usual according to step 7 of the article:http://support.microsoft.com/kb/929135

  Bindu R - Microsoft Support
  Visit our Microsoft answers feedback Forum and let us know what you think.

• I received this error message after you remove the address something about Cloud.app

  I received this error message after you remove the address something Cloud.app.   Can you tell me how to fix this error message. "  '/'  "  ?

  Hello Phyllis,

  When you receive this error now?

  Let's run boot minimum troubleshooting to find the cause.

  Windows XP:

  http://support.Microsoft.com/kb/310353

  http://support.Microsoft.com/kb/316434

  Windows Vista and Windows 7:

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  Please note that after refine us the cause, it is important that we return to a normal startup and manually delete the startup program.

  Best regards

  Matthew_Ha

• Blue screen with STOP error 0x0000007B (0xBA4CF524, 0xC0000034, 0x00000000, 0x00000000)

  I have my Acer 5920 laptop, 2 GB of RAM and 160 hard drive, last stop system time correctly with all the files to day, but when I restart then comes windows XP Jean-Christophe and then a blue screen with the error. Nor I have install new software or remove something in the laptop. My system was perfect, and that was before the last stop.
  I have Windows XP SP2-teacher-pack. I have the original CD of this package.
  But when I use the CD then nothing is happen and come same messgae of error. I do not have any other CD bootable for windowXP except your originalCD.
  Please suggest me what I should do to fix my probem. I'm not to much expert for the formatting and other things computer.

  After reading your following suggession:
  Here are a few things to try:
  The first thing to do is to boot your system and start pressing F8 as soon as it starts booting.  You will get the Windows startup options screen.  Select "Disable automatic restart in the event of system failure" and let it restart.  When it starts, it can now stop with an error screen and give an error message and code.

  Disconnect all external devices (printers, USB Hub, drives external, etc.) and try to start.

  I got the result of the error that comes on a blue screen after you follow your process-blue screen with STOP error 0x0000007B (0xBA4CF524, 0xC0000034, 0x00000000, 0x00000000)

  Thanks in advance for help
  What about nice Rajneesh

  Just one quick response for others...

  Go to your bios to change the mode of training of your s - ata AHCI or IDE Compatible mode or all that apply :) Windows XP is not like SATA, because it has no native support for it. At the start of the second phase of a Setup program, it would fail with this BSOD.

  Also read the following Microsoft article that describes many other causes (including file system damage):Troubleshooting of errors "Stop 0x0000007B" in Windows XP Advanced

  Sometimes, your BIOS will provide its default settings after a system crash or a configuration. Should not happen, but it is...

  For BIOS-discussions, see: 0x0000007B 0xBA4cf524 - Forum of Support PC - Free Computer help , XP installation: * STOP: 0x0000007B (0xF78D2524, 0xC0000034, 0x00000000, 0x00000000)? - Page 4 - Cyber Tech Help Support Forums , 0x0000007B (0xBA4CF524 - Google zoeken .)

  Have fun, and... Peace!

  Devvie

  ~ ~ ~ * E-mail address is removed from the privacy * ~ ~ ~

  CONARE nullius momenti videri fortasse missilibus careant
  ------
  All the spelling mistakes are my own and may not be distributed under the GNU General Public License! -(© 95 1 by Coredump; 2-10 by DevNullius)

• I am trying to install windows XP Professional. Installation stops with error "0x0000007b".

  How to install Win XP on PC with intel i3 processoe running win7

  Hello

  I'm working with a legacy system. My programs to work with Windows XP and more excellent only.

  Now, one day I can not PC with Windows XP we have windows 7 to house high-end system running on the desktop computer intel i3 processor.

  I am trying to install windows XP Professional. Installation stops with error "0x0000007b".

  The new PC with SATA HDD and CD ROM, I was told that windows XP Setup has no support for SATA drives, at the same time if I want to install the drivers, that it seems that for the floppy drive. Thus, it is difficult to install the drives.

  Also when I spoke to Dell Tech support person, he said I can't install Windows XP on the Intel i3 processor. I don't think, but I will this differ from expert.

  Can someone help?

  Hi Steve,.

  You can follow this link & check if the problem persists:

  Error message "STOP 0x0000007B" when you restart your Windows XP-based computer

  
  Reference: Advanced troubleshooting of errors "Stop 0x0000007B" in Windows XP

  If the problem persists, please ask your question in the TechNet forums for assistance.

  Hope the helps of information.

• Cannot reinstall PSE 7 after the restoration of PC (Win XP). Impossible to uninstall, STUCK. Help, please.

  Error message when you try to start the 7 Elements after the restoration of PC (Win XP) "couldn't start b/c the application configuration is incorrect". When you try to uninstall 7, it doesn't appear in the Conrol Panel. But there is a Photoshop 7 folder in Program files. If someone could HELP Please, it would be greatly appreciated. I use this program so much!

  Thank you in advance...

  Here's the Adobe documentation to manually uninstall PSE7:

  http://kb2.Adobe.com/CPS/405/kb405847.html

  Ken

• Management of errors with the return code

  Hello
  
  I set up an email notification which is the last step in case of failure and success. As I am manages all stages with a link (red arrow) KO, ODI handles any error that occurs and so there is never a return code different from 0 (success). It's great because the administrator receives an email with detailed error information, but the process is performed by an external Scheduler and IT operations wants the Scheduler must be notified by the return code if an error occurs.
  
  How can I do both: manage a mistake and will continue to receive a return code other than 0 on the command line?
  
  Thank you
  Matt

  In your package.

  For the final step before sending the mail.

  Create 2 steps (which will be the same), with both the same send email step.

  Put the green arrow of your last treatment for the first shipment of e-mail, it will be your end if no error.

  Put the red arrow of your last treatment for the second e-mail was sent, it will be your end if there is an error.
  After the mail error put another step which end in error every time, as a procedure that calls a ' select * of fgfhfju "(if you don't have a table of fgfhfju) and bind this step with a green arrow at the stage of email from error.

  You can now separate finishing way in your package, one for the error and another for the right side.

  Hoping to help.

  Kind regards

  Brice

• "404 - page not found" error message after downloading and installing Firefox 15

  "404 Page not found" error message after you download the latest version of Firefox.

  It is sometimes the result of a software firewall that protects you against modified applications. Or it could be something else. Can you look at this article and see if it helps: Firefox can not load websites, but can other browsers.

• PCI-MIO-16-4 error 200329 after running a while

  I use a card PCI-MIO-16-4 for a combination signal generator and an oscilloscope for a student laboratory exercise.  I use ao0 to generate a variable frequency waveform (defined by the controls on the front panel) and ai6 to acquire the resulting signal.  To experience the two must be synchronized for the acquisition of scope starts simultaneously with the beginning of a generation analog.  Synchronization is performed using ctr0 in generation mode and set the same frequency as the analog output.  The meter output through rtsi0 for relaxation of beginning on the analog input.

  The application seems to work very well until the output frequency is changed "too quickly" while the analog input section will post 200329-error of the vi DAXmx Start Task.  After receiving this error, the computer must be restarted to resume operation of the Commission - even MAX panels will be simply repeat the same mistake on the analog inputs up to a reboot.

  If have tried the application on a Board of the USB-6221 BNC (using pfi9 to route the trigger start signal) and were unable to make the same error.

  It is on a computer running window 7 Enterprise sp1 with LabVIEW 2012 (32-bit) sp1 with the f5 patch installed.  DAQmx 9.6.2 has been installed for the original tests for both cards.  Installation DAQmx 9.8.0f0 does not change the behavior.  The PCI-MIO-16-4 passed the tests of the DAQ Diagnostic Utility 2.1.

  I tried using rtsi6 and rtsi0 as the routing without behavior change trigger signal.

  I have attached a stripped down version of the application that is always the problem.  There are 7 required files so that they are in a single .zip file.  With the frequency setting knob, it takes usually just a couple of "twists and turns" on the controller to cause the entry to the analog error.  The output of the DAQ Diagnostic Utility is also attached.

  Thanks for advice on what I can hurt in this application.

  The solution to the error:

  First attempt, the application had two structures of parallel events that have allowed the frequency be changed while there was also an acquisition that occur.  Modified to have a structure of single event so that the frequency changes may occur between acquisitions (risk of conflict Access Board?).  This made no difference to the error.  He would always get error-200329 after that the frequency has been changed several times.

  Discovered that just reset the jury would clear the error.  Considered catch the error and reset the jury whenever it happened.  Prefer something that will prevent the error from happening at all.

  Final solution was to erase the data acquisition task after each acquisition scan and reset.  It was only necessary erase the tasks of acquisition and not production jobs or a timer.  After several hours of change of frequency, amplitude and phase, no error had occurred.  I think that it has cured the problem.

  I now have two different copies of the application.  One is for use with the PCI-MIO-16-4 (new one that clears the task of acquisition after every scan) and one for use with the NI USB-6221, who uses still two parallel event structures, does never erase the task of acquiring and never shows the error when it is used with anything other than the PCI-MIO-16-4.

• Error code Win32 returned by the print processor: 2147500037. Unspecified error

  I see that this error code has been resolved.   I have a few questions on this topic tho.  Loop here, is where the fun begins.  If i see this exact problem in my hosted cloud envorioment.  The printers are installed locally and are drawn on the network when the user logs in the hosted environment. The user connecting to a full desktop, which is a Windows 2008 R2 server server.  They only receive this problem when printing via the cloud. that uses the same printer drivers installed on the local PC.  On-site printing has the success rate of 100%.

  Here are the mistakes I see:

  Https://rem.exactbid.com/ServiceRequest/SRFsmart/srprintable.as, belonged to craig_REM, document failed to print on printer HP LaserJet P2050 Series PCL6 (from CRAIG) in session 18. Try printing the document again, or restart the print spooler.

  Data type: NT EMF 1,008. Spool file size in bytes: 589824. Number of bytes printed: 540384. Total number of pages in the document: 2. number of pages printed: 0. Client computer: \\VS-XA35. Error code Win32 returned by the print processor: 2147500037. Unspecified error

  Where I am confused, is that I have no driver installed on the server.  they are all drawn in front of the user login local machine solange.  With printing works fine locally.  Uninstalling the drivers will make them any good?  or where should I be looking next?

  Hello

  Thank you for visiting the Microsoft answers community site. Your question of Windows is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the TechNet Windows Serverforum.

  http://social.technet.Microsoft.com/forums/en/category/WindowsServer/

• 70073712 error code when you try to install Win 7 SP1

  I am using Windows 7 32 bit on a machine with 4 GB of RAM 540 i3.

  I get error code 70073712 when trying to install Win 7 SP1 via windows update.

  I disabled all startup programs and services not microsoft.

  I ran the fix - it utility and update v10 system utility preparation x 86.

  I have still some errors on the log to check ON that I can't fix, I don't know if they help or not.  Log is shown below:

  =================================

  Preparation of control system was updated.

  Binary version 6.1.7601.21645

  Package Version 11.0

  2011-02-25 22:18

  Checking Windows Service Packages

  Checking of manifests package and catalogs

  Checking package Watchlist

  Watchlist checking

  Checking packages

  Control components store

  (f) CSI Manifest and S256H Do Not Match0x00000000 winsxs\Manifests\x86_microsoft-windows-smbserver-common_31bf3856ad364e35_6.1.7600.16664_none_03c12997716b5264.manifestx86_microsoft-windows-smbserver-common_31bf3856ad364e35_6.1.7600.16664_none_03c12997716b5264

  (f) CSI Manifest Failed Catalog Check0x00000000 winsxs\Manifests\x86_a3a447e7a026fd8b08eef9015c3fd303_b77a5c561934e089_6.1.7600.20717_none_3c3b72980dd0607e.manifestx86_a3a447e7a026fd8b08eef9015c3fd303_b77a5c561934e089_6.1.7600.20717_none_3c3b72980dd0607e

  (f) CSI Manifest Failed Catalog Check0x00000000 winsxs\Manifests\x86_microsoft-windows-smbserver-v1_31bf3856ad364e35_6.1.7600.16664_none_d9e264be57b7d382.manifestx86_microsoft-windows-smbserver-v1_31bf3856ad364e35_6.1.7600.16664_none_d9e264be57b7d382

  (f) CSI Manifest Failed Catalog Check0x00000000 winsxs\Manifests\x86_9edaf6d3bef8e3b8a511c965c4676cc0_b77a5c561934e089_6.1.7600.20717_none_fba4726a5de9641a.manifestx86_9edaf6d3bef8e3b8a511c965c4676cc0_b77a5c561934e089_6.1.7600.20717_none_fba4726a5de9641a

  (f) CSI Manifest Failed Catalog Check0x00000000 winsxs\Manifests\x86_microsoft-windows-smbserver-common_31bf3856ad364e35_6.1.7600.20789_none_043a27fc8a94a8c3.manifestx86_microsoft-windows-smbserver-common_31bf3856ad364e35_6.1.7600.20789_none_043a27fc8a94a8c3

  (f) CSI Manifest and S256H Do Not Match0x00000000 winsxs\Manifests\x86_e8bf52ce827220c20c57727d1ef1b0f3_b03f5f7f11d50a3a_6.1.7600.20717_none_c2175e5f4430b21d.manifestx86_e8bf52ce827220c20c57727d1ef1b0f3_b03f5f7f11d50a3a_6.1.7600.20717_none_c2175e5f4430b21d

  (f) CSI Manifest Failed Catalog Check0x00000000 winsxs\Manifests\x86_5f9114f1cdba6b133e611c33f9d42896_b77a5c561934e089_6.1.7600.16597_none_a1c1ac15f6bb52cb.manifestx86_5f9114f1cdba6b133e611c33f9d42896_b77a5c561934e089_6.1.7600.16597_none_a1c1ac15f6bb52cb

  (f) CSI Manifest Failed Catalog Check0x00000000 winsxs\Manifests\x86_0f7a1a89936e7d82f675294dce25e472_b77a5c561934e089_6.1.7600.16597_none_b566a48eb4b33968.manifestx86_0f7a1a89936e7d82f675294dce25e472_b77a5c561934e089_6.1.7600.16597_none_b566a48eb4b33968

  (f) CSI Manifest Failed Catalog Check0x00000000 winsxs\Manifests\x86_0d9aca2e69a54e84f2113f11119a3945_b03f5f7f11d50a3a_6.1.7600.16597_none_7ca86e604e0c3fd6.manifestx86_0d9aca2e69a54e84f2113f11119a3945_b03f5f7f11d50a3a_6.1.7600.16597_none_7ca86e604e0c3fd6

  Summary:

  Seconds executed: 58

  Found 9 errors

  County of apparent CSI and S256H Do not Match Total: 2

  Manifest CSI has not catalog check the total count: 7

  Unavailable repair files:

  winsxs\manifests\x86_microsoft-Windows-SMBSERVER-common_31bf3856ad364e35_6.1.7600.16664_none_03c12997716b5264.manifest

  winsxs\manifests\x86_a3a447e7a026fd8b08eef9015c3fd303_b77a5c561934e089_6.1.7600.20717_none_3c3b72980dd0607e.manifest

  winsxs\manifests\x86_microsoft-Windows-SMBSERVER-v1_31bf3856ad364e35_6.1.7600.16664_none_d9e264be57b7d382.manifest

  winsxs\manifests\x86_9edaf6d3bef8e3b8a511c965c4676cc0_b77a5c561934e089_6.1.7600.20717_none_fba4726a5de9641a.manifest

  winsxs\manifests\x86_microsoft-Windows-SMBSERVER-common_31bf3856ad364e35_6.1.7600.20789_none_043a27fc8a94a8c3.manifest

  winsxs\manifests\x86_e8bf52ce827220c20c57727d1ef1b0f3_b03f5f7f11d50a3a_6.1.7600.20717_none_c2175e5f4430b21d.manifest

  winsxs\manifests\x86_5f9114f1cdba6b133e611c33f9d42896_b77a5c561934e089_6.1.7600.16597_none_a1c1ac15f6bb52cb.manifest

  winsxs\manifests\x86_0f7a1a89936e7d82f675294dce25e472_b77a5c561934e089_6.1.7600.16597_none_b566a48eb4b33968.manifest

  winsxs\manifests\x86_0d9aca2e69a54e84f2113f11119a3945_b03f5f7f11d50a3a_6.1.7600.16597_none_7ca86e604e0c3fd6.manifest

  Customer experience report downloaded successfully.  Thank you for your participation.  For more information, see the Microsoft Customer Experience Improvement Program on the Microsoft web site.

  Can anyone offer any help on solving this problem and get installed SP1, as I'm stuck now!

  Thank you

  Thomas

  
  

  Hello Thomas_Si,

  Thank you for your message.  Please, try the following steps:

  Since you have already downloaded and run the system update tool, you can move on to step 2.

  1. According to your architecture of Windows 7, download / install and run the tool update system - CheckSur you can download the tool from the links below depending on your system type.

  Download the tool update system (64-bit)

  Download (32-bit) system update readiness tool

  2. click Start type cmd (you should see the command prompt fill up) right click and select run as administrator

  Inside the command prompt, type sfc/scannow

  For more information regarding the file system checker.

  * If corruption is found, see How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  3. once the SFC is finished, check your hard drive for errors.

  4 restart the system update readiness tool. If errors have been eliminated, try to reinstall Service Pack 1. If this is not the case, go to step 5.

  5. perform a Startup Repair, when starting, try to install the Service Pack.

  Please let us know the details of each scan or utility. We can't wait to hear back on your part.

  See you soon

• I have an error message after an update, WindowsUpdate_0000737D""WindowsUpdate_dt000, can someone please help, my computer installs updates whenever I stop. "

  I have an error message after an update, WindowsUpdate_0000737D""WindowsUpdate_dt000, can someone please help, my computer installs updates whenever I stop. "

  @cinziac (who has not declared his complete version of Windows):

  Visit the Microsoft Solution Center and antivirus security for resources and tools to keep your PC safe and healthy. If you have problems with the installation of the update itself, visit the Microsoft Update Support for resources and tools to keep your PC updated with the latest updates.

  ~ Robear Dyer (PA bear); MS MVP (that is to say, mail, security, Windows & Update Services) since 2002. DISCLAIMER: I do not represent nor don't work for Microsoft

• Error message after extraction of sp3 for XP Pro: System cannot find the path specified.

  XP Professional installation error message after extraction of sp3 on hard disk, message: System cannot find the path specified.
  Whenever I try to install, I get the same message. How can I fix it? I can't use the "fix" without sp3 installed.
  Any help would be greatly appreciated!

  "system cannot find the path specified".

  A google search revealed this can help...
  http://aumha.NET/viewtopic.php?f=62&t=33406

  Also, what is your level of service current pack (start-run then type Winver, and then press enter)? If you have no current service pack level, you must first install SP2. Unfortunately, the link for that

  http://www.Microsoft.com/download/en/details.aspx?displaylang=en&ID=28

  doesn't seem to work today. If all goes well he'll be reinstated soon.

  Tricky

• [Error number: 0x8024400A] trying to download SP 3 for XP, the error code is returned. What it means?

  [Error number: 0x8024400A] trying to download SP 3 for XP, the error code is returned.  What it means?

  You must be at Service Pack 3 level before you can use Windows updates.

  To determine which service pack is currently installed on your computer, follow these steps:

  1. Click Startand then click run.
  2. Copy and paste, or type the following command, and then click OK:

  winver

  A dialog box displays the version of Windows and the service pack that is currently installed on your computer.

  If you haven't already done so, you will need to install the SP2 and SP3 (SP1 note no longer exists).

  How to obtain the latest Windows XP service pack
  http://support.Microsoft.com/kb/322389

  Installation of SP2 - http://support.microsoft.com/gp/xpsp2getinstall

  Steps to take before you install Windows XP Service Pack 3
  http://support.Microsoft.com/kb/950717

  It is stated in "How to obtain the latest service pack XP" is.

  If you have problems obtaining the service pack from Windows Update, you can download the package of standalone update from the Download Center. This page will say that this installation package is intended for it professionals and developers. However, you can download this file safely. The following file is available for download from the Microsoft Download Center:

  Download the Windows XP Service Pack 3 package now

  See also: http://support.Microsoft.com/kb/2497281
  You may be unable to access the site Web Windows Update in Windows XP, Windows 2000 or Windows Server 2003