Error-1074360293 (IMAQdx Timeout) after completing the acquisition for some time

My vision in LabVIEW application makes several acquisitions and successful treatment but then acquiring (grab) suddenly fails with a timeout error (-1074360293, IMAQdx: timeout). The error does not when acquiring only the images.

After that the error occurred that no acquisition is possible. Although LabVIEW is closed MAX Returns a time-out error. Only restart helps.

some details of the material:

3 controllers FireWire (1394-a)

3 cameras connected to the first two controllers, one third (total of 7 cameras)

Mode for all cameras: 1280 x 960 Mono 8 fps 7.50

The bandwidth for a FireWire controller is sufficient. (Three cameras on a single controller are running without any problem).

Consume the application memory is short before or after that the error occurs. But I can't find where exactly.

Until the error occurs a few minutes until one and a half hour pass.

More details will follow.

Is there a FireWire or specialist in the vision that can help you?

Greetings,

SHB

Change the driver it seems to fix the problem:

"Compatible (legacy) 1394 OHCI host controller" (in German: "OHCI - 1394-Hostcontroller (alt) konformer")

With this pilot test has worked for more than 66 hours without raising an error.

Some Articles about:

http://www.RME-audio.de/forum/viewtopic.php?id=9827

http://www.myvideoproblems.com/ProblemPages/CannotCapture.htm

Tags: NI Hardware

Similar Questions

  • Google Calendar becomes inactive in Firefox. Reset Firefox solves the problem for some time (sometimes minutes), then it becomes inactive.

    Google Calendar becomes inactive in Firefox. Can not navigate, cannot change the appointments, can only view an appointment, then freezes and nothing is more possible.
    Reset Firefox solves the problem for some time (sometimes minutes), then it becomes inactive.
    Firefox 28.0, Windows 7.
    Google Calendar is OK in Android and syncs with my PC OK.
    Works fine in Internet Explorer.
    Please notify.

    The extension Freeven pro is probably the problem. Only that disable and check again.

    If you have the same problem after having disabled the extension pro Freeven then, disable graphics hardware acceleration.

    You will have to perhaps restart Firefox for it to take effect, so save any work first (e.g. you compose mail, documents online that you are editing, etc.).

    Then perform the following steps:

    • Click on the orange top left Firefox button, then select the 'Options' button, or, if there is no Firefox button at the top, go to tools > Options.
    • In the Firefox options window, click the Advanced tab, and then select 'General '.
    • You will find in the list of parameters, the checkbox use hardware acceleration when available . Clear this check box.
    • Now restart Firefox and see if the problems persist.

    In addition, please check the updates for your graphics driver by following the steps in the following knowledge base articles:

    In safe mode hardware, acceleration is disable by default.

    Thank you.

  • dad bought me a computer PORTABLE from NUTRIGEST I HAVE BEEN out of the CITY FOR SOME TIME AND LATER BETWEEN the AUTHENTICITY CODE PRODUCT, AND IT's not SAYIING VALID, BUT I KNOW THAT CANT BE REAL CODE IS

    dad bought me a computer PORTABLE from NUTRIGEST I HAVE BEEN out of the CITY FOR SOME TIME AND LATER BETWEEN the AUTHENTICITY CODE PRODUCT, AND IT's not SAYIING VALID, BUT I KNOW THAT can NOT BE TRUE

    If it is a new machine call or go to circuit city and get them fixed.  If they sold you the laptop, indicating that it included Windows XP then the onus is on them that provide you a valid COA and the product key.

    John

  • virus: I struggled with the virus for some time and cannot get rid of them

    I have struggled with the virus for some time and cannot get rid of them. I bought a few programs, but they have also been infected. any suggestions for a really good virus buster.

    Hello

    First of all, an antivirus solution to an already infected system of loading is usually pretty useless. The bug will block all attempts to remove or load what it sees as a threat. Second, without knowing which virus you are affected by, it is difficult to be precise.

    You can take action include:

    (a) work in safe mode, there is much less likely that the virus is able to load and resist actively.

    (b) the safe mode, run utilities malwarebytes.org and AV solution that was installed * before * your infection.

    (c) post is back with a better description of what is on your system to learn more targeted advice.

    Good luck, Rick Rogers, aka "Crazy" - Microsoft MVP http://mvp.support.microsoft.com Windows help - www.rickrogers.org

  • I got the flashplayer for some time - I need to know how to enable adobe to install the latest update?

    I had for some time adobe flash player - I need to know how to enable adobe to install the latest update?

    the version is 21.0.0

    browser - safari

    Mac OS x

  • How to take the exit for some time on a loop to do comparison

    Hi all!

    I had a problem with my labview project, asking me to make the comparison with

    2 output values, both of which are within his time looping.

    To clarify this issue, I have 2 data entries, they are read in 2 loops while respectively once.

    Now I need to extract these values outside read the while loop to make the comparison. However simply

    the 2 outputs out of wiring to a comparison function does not work. The enforcement highlight function

    I can see that the data coming out of the loop!

    So, I would ask if anyone has any idea, thanks!

    Chao


  • Ligtroom 6 best, I will describe my problem once the hour 1. After 4 weeks, I get the message "trial version Ligtroom 6 expired 2. You will be asked to fill out my license number 3. After completing the restart and get the message "error 16" 4. Never

    Ligtroom 6
    Better, I will describe my problem once right
    1. always after 4 weeks, I get the message "trial version expired Ligtroom 6a
    2. you will be asked to fill out my license number
    3. After completing the restart and get the message "error 16".
    4. all again manager install Adobe again and install this once again repeated problem Ligtroom each month can ensure that this stops my version is a purchased official version
    Now repeat the problem after only 4-5 days!
    Caveat! I'm not a computer specialist are not too complicated solution

    Since this is an open forum, not Adobe support... you must contact Adobe personnel to help

    Chat/phone: Mon - Fri 05:00-19:00 (US Pacific Time)<=== note="" days="" and="">

    Don't forget to stay signed with your Adobe ID before accessing the link below

    Creative cloud support (all creative cloud customer service problems)

    http://helpx.Adobe.com/x-productkb/global/service-CCM.html

  • vSAN upgrade from 5.5 to 6.0 - Timeout to complete the operation

    Hi all

    I've been running a 5.5 vSAN configuration identical to William Lam to the virtual Ghetto (a killer custom installation of Apple Mac Mini running VSAN | virtuallyGhetto) for some time and the only reason not to upgrade more far was because of wanting to maintain a configuration of 5.x Horizon view inherited who needs vCenter 5.5. I've now decided this should not dictate my whole environment then after a successful move to 6.0 on the hosts and VCSA, I thought I would upgrade to vSAN 6 to take advantage of the improvements it brings, not to mention to remove the nagging alerts on the vSAN update available.

    After running through the prerequisites this fact compensation involved in a number of vswp files inaccessible, vSAN reported a good state of health and so I started with the upgrade online, be sure to include - allow-reduced -redundancy I have a 3-node cluster.

    When running and after about 20 minutes of nail biting (by accepting the fact that his machines of laboratory accommodation only, their fate can be determined by the success of failure of the upgrade), I received the following in the TVR: -.

    : Deletion of this VSAN disk group failed

    : A general error occurred: could not evacuate data for disk uuid 52da00fa-c8f2-fdb8-924c-3007d480ac4d with error: timeout to complete the operation

    : Cannot delete the VSAN disk, leaving group.

    : Upgrade tool stopped due to the error, please address reported the problem and run the tool again to complete the upgrade

    Someone at - it guidance on how to approach the time-out, or he could escape that I would understand rather the root cause that blindly blow to remove all of the configuration and reboot.

    Thanks for your help!

    All the best


    Andrew

    Hi Duncan,.

    I managed to work around the problem in the end, in a weird way. I ended up changing the default vSAN FTT from 0 to 1 storage policy and reapplied to redistribute the data or the light evenly on the hosts as expected to the compliance of the report. After a few hours, I then changed the default vSAN strategy towards an FTT of 0 and again applied. By running the TVR command with the parameter - allow_reduced_redundancy again by the failed sequel, but a quick check on the vSAN has shown that the majority of data consumption was now on the hosts 2 and 3 with a tiny 3 GB of use reported against the disk of the host of the first group. At that time, I've been manually the disk group on host 1 (choose not to evacuate the small amount of data that has been left). After you re-create the disk on the host group, it automatically came back in as v2 and I repeated the process described above in the other two hosts effectively the content of vSAN brewing between the hosts and drop what I believe has been corrupted/no valid data on the host group could not be evacuated by the upgrade process.

    At the end of it, all my virtual machines survived the upgrade of vSAN.

    See you soon

    Andrew

  • Error "have sufficient privileges to complete this installation for all users of the machine. "log on as an administrator and try again the installation" when you try to install iTunes

    Original title:

    I just installed windows7, I had to uninstall itunes in order to complete the instalation of windows7. everything went well until I tried to reinstall itunes.

    During this process, I get the message "you don't have sufficient privileges to complete this installation for all users of the machine. log on as an administrator and try this installation again. ». but I am logged on as administrator.

    Hello

    To resolve this problem, use the following methods. After completing the steps in each method, check to see if the issue is resolved before you go to the next method. If the problem is resolved by any method, you do not have to use other methods.

    Method 1:

    Right click on the installer for iTunes and click Run as administrator.

    Method 2:

    Disable user account control settings and check.

    Enable or disable the User Account Control

    Note: User Account Control (UAC) can help prevent your computer from unauthorized changes. UAC notifies you when changes will be made to your computer that require administrator-level permissions. Disabling it can make your compromised computer. Please make sure that enable you UAC, once you have completed troubleshooting.

    Method 3:

    Allow the default Administrator and try to install it in this user account.

    a.Click on Start, click principally made programs, Accessories, right-click on command prompt and select run as administrator.

    b.Type in the following command and press ENTER.

    NET user administrator / active: yes

    c.Log disable the current user account and log in to the user called Administrator account.

    d.Install iTunes in this default Administrator account.

    e.Once of that installation is complete, the default administrator is disconnected.

    f. log in to your user account.

    g.Disable the default Administrator account. Follow these steps.

    i.Click on Start, click principally made programs, Accessories, right-click on command prompt and select run as administrator.

    II. type the following command and press ENTER.

    NET user administrator / active: No.

  • The Finder cannot complete the operation because some data in the 'AdobeGermanSpeechAnalysisModels1All.dmg' cannot be read or written. (Error code - 36)

    Tried to download CS4 and got this message

    The Finder cannot complete the operation because some data in the 'AdobeGermanSpeechAnalysisModels1All.dmg' cannot be read or written.

    (Error code - 36)

    Need help to resolve this.

    Please see:

    Error "licensing for this product has expired" | CS4, CS5

    Error 1603: A fatal error occurred during installation

    Troubleshoot installation with the Setup logs. CS3, CS4

    I hope this helps.

    Concerning

    Megha Rawat

  • Syntax error, insert "Expression AssignmentOperator" to complete the phrase

    Hi experts,
    I am very new to Java. Currently, I'm stuck with the exception of the program. Please help me understand what the problem is. The eclipse triggers the error "syntax error, insert"Expression AssignmentOperator"to complete the phrase" to the "exception; command"as the code below.

    Thank you
    Hieu

    Published by: user122479 on April 5, 2013 16:23

    Please add

    -tags around your code and the complete Stacktrace.
    
    bye
    TPD                                                                                                                                                                                
    
  • Cancellation of WIP job after completing the work

    Hello everyone,

    There is a question of "Annulant the WIP job after completing the work.

    Please let me know how to solve this or workarounds.
    Give me the navigation please.


    Thank you

    Hi Adam;

    Please search your question in metalink as cancelling WIP Job there are 272 available docs. Please check. The best way to check your question in these docs

    Respect of
    HELIOS

  • iTunes 12.3.3.17 crashes after playing the song for about 30 seconds

    Hello!

    I have a problem, I'm fighting currently to solve - iTunes 12.3.3.17 iTunes crashes after playing the song for about 30 seconds.

    I already tried things:

    (1) the preferences removed from the library, so that they can be recreated - did not work;

    (2) reinstalled iTunes - not worked;

    (3) removed freshly installed Bitdefender Antivirus for Mac - did not help.

    Product: Macbook Air

    OS X El Capitan

    I receive the following information in the log file

    ===============================================================

    Crashed thread: queue main iTunes shipping 0: com.apple.main - wire

    Exception type: EXC_BAD_ACCESS (SIGSEGV)

    Exception codes: KERN_INVALID_ADDRESS at 0 x 0000000000000011

    Note the exception: EXC_CORPSE_NOTIFY

    Can you help me please?

    elina_j,

    It seems that your iTunes software seems to be stop unexpectedly when you play the music back after about 30 seconds or more. First, I would check to see if there are errors on the disc that need repair:

    Disk utility (El Capitan): a disc repair

    Once the repair and verification done go ahead and test the issue again. If that fixes it, then great! If this is not the case, however, I would then remove third-party plug-ins that may interfere with the operation of iTunes:

    Test with iTunes plug-ins removed.

    • Quit iTunes.
    • Mac OS X:
      • ~/Library/iTunes/iTunes Plug-ins(The "~" represents your home folder)
      • /Library/iTunes/iTunes Plug-ins
    • If all the files in this folder, move it to the desktop temporarily.
    • Open iTunes and test to see if the problem is resolved. If so, you can leave these plug-ins removed iTunes. If you want to reuse these iTunes plug-ins, check with the supplier of iTunes plug-ins to see if updates are available.

    From: iTunes: may crash when you plug in the iPhone, iPad or iPod touch

    If the problem is still there after removing the plugins or there is none to remove, then you must then create a new library, add content to it and see if the problem persists it:

    Open a different iTunes library file or create a

    Mac

    1. If iTunes is running, quit iTunes.
    2. Hold down the Option key when you open iTunes.
    3. You will see a message that says choose iTunes library. Depending on what you want to do, choose Create or choose library.

    Now if the problem is still not resolved then you can create a new user admin on your computer and test it there too well?

    OS X El Capitan: set up users on your Mac.

    Add a user

    1. Choose the Apple menu > System Preferences, and then click users and groups.

    2. Click on the lock icon to unlock, then enter an administrator name and password.

    3. Click on the button Add below the list of users.

    4. On the pop-up menu click new account, and then choose a user type.

    • Administrator: An administrator can add and manage other users, install applications, and change the settings. The new user that you create when you set up your Mac is an administrator. Your Mac can have multiple administrators. You can create new ones and convert standard users to administrators. Don't set up the automatic connection to an administrator. If you do, someone could simply restart your Mac and access with administrator privileges. To secure your Mac, don't share administrator names and passwords.

  • Enter a display name for the new user. An account name is automatically generated. To use a different account name, enter it now, you can't change it later.

  • Enter a password for the user, and then enter again to verify. Using an index of password is recommended to help the user remember the password.

  • Click on create user.

  • The result of the new user will determine what we then so let us know how it goes! Thank you for using communities of Apple Support.

  • Error ORA-16724: could not resolve the deficit for one or more databases in waiting

    I came to work today with the following error is displayed:

    February 5, 2014 01:27:19 error ORA-16778: make the mistake of transport for one or more databases.


    Looks like this error disappeared but now I have the following error:

    February 5, 2014 11:52:40 error ORA-16724: could not resolve the deficit for one or more databases in waiting

    I did some research on the forums and I think I need backup and restore, but I'm not sure.

    Here are some questions that I saw others asking in the forums:

    PRIMARY:

    Select max(sequence#) from v$ archived_log; -24589

    Select current_scn in the database of v$. -871568619

    SECONDARY:

    Select max(sequence#) from v$ archived_log; -24589

    Select max(sequence#) from v$ archived_log in case of application = 'YES '; -24562

    Select current_scn in the database of v$. -870987797

    Select * from v$ archive_gap;

    Thread # Low_Sequence # High_Sequence #.

    1 24563 24563

    Looks like everything is working, but the error is still appearing in OEM primer.

    The issue ended up being with the control file. I followed of many blog posts on how to roll forward the database before and they all said to restore the control file before you recover the database. I followed this paper: http://docs.oracle.com/cd/B28359_01/server.111/b28294/rman.htm#CIHIAADC and it worked as expected. The old control file has had 6 data files that were in a different place than the others. The new control file, I created the primary had all the files of data in one place. After correcting the control to point to the locations correct datafile all started working again.

  • After downloading the update for Yosemite 10.10.5, I got an annoying popup with a beep sound blaring that says that Safari crashed. I've forced to leave Safari, rebooted and popup returned once more. Restarted again and popup went. What was it?

    After downloading the update for Yosemite 10.10.5, I got an annoying popup with a beep sound blaring that says that Safari crashed. I've forced to leave Safari, rebooted and popup returned once more. Restarted again and popup went. What was it?

    Open Safari while holding the SHIFT key

    Try to reset the settings of Safari:

    1. open Safari

    2. click on the Safari menu at the top (to the right of the Apple logo)

    3. Select the Preferences/Privacy tab

    4. click on remove all data from the Web site

    5. close Safari.

    Remove cache Safari files:

    1. click on finder

    2. look for the menu GO to top

    3. click on GO and hold down the option key. This will show a user library folder.

    4. click library and find the Caches folder

    5. in the folder caches com.apple.Safari Ouvrezledossier

    6. move the Cache.db file Trash.

    This should solve the problem. If it does not help, try to disable the Safari extensions

    1. open Safari

    2. click on the Safari menu at the top (to the right of the Apple logo)

    3. Select Preferences

    4. find the Extensions tab

    5 disable all extensions of

    6. relaunch Safari

Maybe you are looking for

  • T440s / S440 / other 14-inch laptop and debian

    Hello I would buy a computer thinkpad notebook. However, I don't want to have problems when I install debian (drivers).Firstly, I am from France and I beg you to excuse me if I speak very well English but is an international language and I prefer to

  • Writing series visa delays

    Hello I use the LabVIEW Vi series to send commands to a DUT. I use the a Sparkfun USB to Serial converter cable for the interface, by connecting directly to the TX and RX pins of my DUT (an MCU). I am able to send and receive data without any problem

  • Convert data from text file to display for hex UDP transmission controls

    Hello I'm reading packets ethernet from a text file containing the actual hex data packets to then send these accurate return through a writing UDP hex data. I can't understand how to feed data into the function of writing UDP as real rather than cha

  • File setupdd.sys could not be loaded

    My installation of Windows XP Edition family became damaged and would not start.  I inserted the CD original and rebooted.  The PC has started from the CD.  It was not long before I got this error message: File setupdd.sys could not be loaded.  The e

  • End of table in the OPS database

    Hi allI need help about table OAF related issue. I need to display data on the table of the OFA. But every time when I click on NEXT 5 RECORDS from a table and return to the previous page, all column values are substituted with the first column in a