ERROR-235140 SMU-4139 self-test

Similar Questions

• SE "error-88705 occurred to self-test" for PCI-6520 after the electric bike for PC

  Hello

  I use a card PCI-6520 on an industrial PC running Windows Embedded Standard (64 bit).  The card works fine in normal use, but if the PC is power off and back on (instead of closing Windows in the start menu), the map do not communicate to the start-up of the machine.  If I try to run a self-test to the MAX, I get the error "error-88705 occurred to the self-test.  The card remains unusable until I restart the PC in the start menu

  Unfortunately this system will be used headless in an industrial application, so if he ever get turned off, it will be turning off the unit and not through windows or the soft power on the Panel switch front of the PC.  It is important that the machine can start in the application of LabVIEW in power on without any external intervention.

  There is also an NI GigE in the PC card and continues to operate correctly regardless of the way in which the PC is off

  Some of the system features:

  Card mother Intel DH67CL

  Core i7 3770 to 3.4 GHz processor

  8 GB RAM

  64-bit Windows Embedded OS

  NOR-DAQmx v9.3.5 driver

  See you soon,.

  Brett

  I just installed version 9.6 of the DAQmx and which seems to have fixed the problem

  See you soon,.

  Brett

• Error code 200020 after self-test when chassis turns off

  Hello

  This may seem absurd, but I accidentally ran a self-test to the MAX on one of the NI PXI boards (6533) in my chassis (NI 1042 q) when chassis power was off. He returned with an error code of 200020. The same thing has happened with three other NI PXI boards: 6723 6713 and 6221. I turned on the chassis and the same error code occurred. Then I restarted my computer, responsible for MAX, and no devices were found even more.

  I followed the steps here to reset MAX, as well as the devices were recognized again, all the self-tests have passed again.

  However, I am concerned as to why it happened. Why the error code keep occurring after that I turned on the chassis? Why MAX ceased to recognize my devices? Something is screwed up when I tried to connect with an off camera? In addition, what does error code 200020? I couldn't find documentation about it anywhere.

  Thank you

  Hey,.

  From your description, it seems that you disable the chassis when the PC is still on. This will cause certainly some problems with your PXI devices, because you're basically hot-swapping PXI devices in your system. This may have also messed up things in MAX, as you saw. You should always have your PXI chassis before your start your computer turned on and turned off after your computer has been shut down. This allows your BIOS correctly enumerate the PXI card, which should hopefully avoid these mistakes in the future.

• Dell xps 8100; Disk failure hard error 2000-0142 0 self test status 79

  Hi guys, I was wandering in the forums for a few hours, now looking for ana response to this question, and can't find anything clear. I have a XPS 8100 that I run a diagnostic and received a 2000-0142 error code that says MSG: error code 2000-0142 hard drive FAILURE 0 self-test status: 79 based on what I read in the forum is that there is a disk failure, and the only recourse is to solve the problem in my view is to replace the drive. Firstly, can someone please give me an absolute confirmation that it is indeed what I have to do, or is there something else I should do to fix this problem first? If a replacement drive is there someone could please tell me how can I do to get my OEM software off the coast of the partition recovery and on my new drive. I now office preinstalled and, of course, premium Windows 7 I would like to see on my new hard drive and I was not provided with one of the disks at the time of purchase. Thanks in advance to all those who respond

  Hi XPS8100kid,

  Welcome to the Dell Community Forum.

  The 200-0142 error is for hard drive failure and you need to replace the hard drive.

  Since the hard drive has not, you would not be able to access the partition recovery on it. Data would be lost and the software already installed on your computer will need to be reinstalled.

  Windows 7 will need to be installed on the new hard drive. Please click the link below to get the procedure of re - install Windows 7.

  http://Dell.to/15MYHsz

  If based in the United States, you can ask for the backup drives by clicking the link below:

  http://Dell.to/Zj7oHA

  I would like to know if additional assistance is needed.

  Thank you and best regards,
  Babita S
  #iworkforDell

  For easy access to the drivers, manuals and updates, please visit our Support Site .

• myDAQ new installation self-test fails 88705

  "' Problem: NEITHER myDAQ"myDAQ1"- Measurement & Automation Explorer-online devices and Interfaces-online OR myDAQ" myDAQ1 "-online self-test does not work. The error message is "the self-test. has failed. -88705 the specified device is missing... »

  My environment:

  8.1 Windows 64 bit running under Oracle VirtualBox Version 4.3.20 running Mac OS x on a MacBook Pro 2012 10.10.1. I have no prior exposure to work with myDAQ, LabView, or any tool of NOR.

  I downloaded NIELVIS1400_downloader.exe for Windows 8.1 to ni.com and it is finished.

  During installation I secured guarded against the problems of Win8FastStartup by stopping and restarting the PC when asked.

  After the installation when I plugged it physically in the myDAQ device, it was recognized by Windows 8.1 because Device Manager has the 'data acquisition' entries under which "NEITHER myDAQ" appears. For NEITHER myDAQ device status is 'this device is functioning.

  When the myDAQ was physically connected, the window "NI ELVISmx Instrument Launcher" popped up. I clicked on the icon 'How to set up your hardware' and the 'get started Guide... "pop up. I checked the blue LED on the device came and it is stable on. I went to "2. Paragraph confirms the recognition of the devices"in implementing on the way, guide and follow the instructions to start the automatic test. There not as described above.

  I noticed similar problems have been reported in the past. Closest to my problem reported by flex11 on 05/05/2014. Reading through I don't see any resolution itself. Another similar problem was solved by manually starting the service 'NOR device charger '. In my case, this service is already running. "NO license server" is the only service stopped, but I guess that's normal for myDAQ.

  I don't have any other product OR installed on the PC.

  I'm sure there is a simple solution to this problem, but I'm afraid it's escape. I'd appreciate any help I can get through this forum.

  Thanks for getting back to me. Your answer gave me stamina I had to move forward.

  I installed http://www.ni.com/download/ni-daqmx-14.2/5046/en/ and finally managed to do work. The exact boot sequence I need is:

  (1) delete myDAQ by USB port and then start Windows 8.1 under VirtualBox.

  (2) after that Windows 8.1 will appear, fix myDAQ on a USB port. If a pop-up window appears asking you to respond, ignore (at the beginning I did not ignore it and myDAQ transformed into a charger USB device firmware such as reported by Device Manager).

  (3) at this stage most likely "VirtualBox VM features-online USB Devices" drop-down menu shows "National Instruments NI myDAQ [0003]" as an entry but without a check mark to the left of the name. Bring the cursor to the left of the name and click here. You should now see a check mark there.

  (4) my myDAQ Self tests started working.

  However, I need the functionality provided by ELVIS as well. So I uninstalled http://www.ni.com/download/ni-daqmx-14.2/5046/en/ and installed from NI ELVISmx 14.0. My boot sequence that I have reported above, didn't work. Just at the moment it's just happened that Oracle has released Version 4.22 of VirtualBox that I wanted to try and ELVIS started to run. I can now use myDAQ DMM.

  One thing that contributed to my problems is fruitless attempts to uninstall the software OR. Unsuccessful uninstalls leave garbage behind who can or cannot cause problems in subsequent relocations. In one case, I'm done with the nidevldu (OR charger) service stuck in the system. I had to do a reset Windows 8.1 recovery operation to get rid of him. I decided to restart Windows 8.1 before uninstalling the software. This ensures that there is nothing in the limbo that past can interfere with a successful uninstallation.

• What are the answers of code of HD521-2W SMART short self-test error when running the diagnostics?

  1 HP Pavilion a4310f, product # AY014AA-ABA, software Build A1NAv6PrA1

  2. Microsoft Windows 7 Home Premium (64-bit) Edition

  3 a receipt the "Failed SMART short self-test HD521-2W" when executing Hardware Diagnostic tools.  Error message:

  Error message the device reported the following State: the previous self-test completed having the read element of the test failed. 01/12/2012-06:21:01

  The first LBA value failure Error Message is 440642933 and the failure occurred after that the device was working since 7943 hours under tension.

  01/12/2012-06:21:01

  4. I made no changes to my system for over a month.

  Device: Hard disk WDC WD64 00AAKS-65A7B SCSI Disk Device, the revision of the firmware 01.03B01

  This unit is my hard drive (it is in factory with partitions C: and D: {Factory Image})

  Hello

  The Smart error code would indicate that the hard disk is running out and must be replaced.  If you want a guide on this, let me know.

  Kind regards

  DP - K

• PCI-5922 self-test error-223431

  I try to reset PCI-5922 OR MAX and get the error code 80040383:

  "There was a problem of resetting the device."

  Then I try the automatic test of NOR-MAX and get the State Code:-223431

  "The self test failed.

  State code:-223431

  Internal software error has occurred in the extended software. Please contact National Instruments. »

  I have tried following th:

  1. reboot the computer

  2. Uninstall and reinstall OR-Scope 15.1.1

  3. change of PCI slot

  After a few tries it turns out that the problem was in the computer. When it is installed in a different computer, the PCI-5922 worked properly.

  Now, it seems obvious: when troubleshooting

  1.) install the Board in another computer

  2.) install another identical sign (if you have one) in computer suspiciuous

  Yonathan

• PCI-1588 fails the self-test and reports error-50550

  I install the drivers for my card NI PCI-1588 and I get the following error:

  The device of that test has failed. From the device driver error report is as follows:

  Error-50550 occurred at the self-test

  Now, I normally don't get angry when I see a mistake, but when the error code is undocumented I said, why?

  In any case, my event viewer says:

  LabVIEW information: error: 400 'Bad Request' for 'deletetree', file ' ': unsupported protocol.

  [nitsuu] [[NO-Sync]]  Fatal error:.\source\nitsu\service\tDriverInitializer.cpp:80 - an error is causing this device OR Sync to the failed to initialize, error-50550 code

  Has anyone else seen this error?

  I'll try to change the location in which my PCI card has been installed, but I would appreciate some debugging info.

  Thank you

  The self-test would occasionally fail my last update... after reinstallation of windows and the only solution I've found that never fails is to go to Device Manager, uninstall the device from there (do not delete the source files for the driver), and then rescan immediately a new material.

  Then it would work in data acquisition!

• Computer XP does not start all of a sudden. Drive hard Self Test error #1-07 Fail. How can I find the meaning of this error of hard disk?

  Computer XP does not start all of a sudden.

  My computer is a HP Lap Top Model zd8000 bought in 2006.  Never had a problem with it before.

  Drive hard Self Test error #1-07 Fail.

  How can I find the meaning of this disc hard test error message?

  Thank you

  I tried the suggestion using chkdsk/r

  The computer ran for a long time, but the computer worked once the process is complete.

  First thing I did was back up my data, I was real worried.

  Thank you very much!!!

• HP Pavilion DV6000 HDD self-test error Fail #1-04

  Hello

  My laptop shows me a blank screen after windows loading screen bar. He did a self test on my hard disk to repair the file, but when I rebooted, it would still continue to do this test. I tried to use a Windows Vista upgrade/recovery, but there is no backup and it keeps giving me an error on all types of restoration. I just tried the hard drive self test and it is said that there is an error Fail #1-04.  From what I've read in the forums, I'll probably have to replace the hard drive, but I don't know how to recover the files on the old drive and what kind of car I need to replace.

  Is my product number: GM010UA #ABL

  Thank you

  patc1995

  With regard to the registration of disk files hard-hit old depends on how much life is left in it. You should be able to ride in a USB HARD drive enclosure, plug into the usb port of a working computer to search files & off copy them to the hard drive of the host computer.

  http://www.Amazon.com/Sabrent-2-5-inch-external-enclosure-EC-RA25/DP/B00JWTPMOO/ref=pd_cp_pc_0

• Error message is "self test feature check."

  At the start there is a floating box with the message "Dell, self test feature check."  Cursor does not and can not go past this message.  Help, please! Thank you

  At the start there is a floating box with the message "Dell, self test feature check."  Cursor does not and can not go past this message.  Help, please! Thank you

  This is the verification of the Dell system. You have to look and see what errors detected.
  I do not vote for me I'm not here for points. If this post helps you, vote. Visit my forum @ http://repairbotsonline.com/

• I have a compaq presario cq60 with vista which was able to start after the installation of windows updates. HP recovery failed with error code 100a and bios self-test gave error fail #1-07. What can I do?

  I have a compaq presario cq60 with vista. Could not start after the installation of windows updates. HP recovery failed with error code 100a and bios self-test gave error fail #1-07. I took the hard drive and installed in my office. Windows Explorer displays the main and recovery partitions.

  The primary partition has the following folders (including hidden & system)

  The recovery partition has the following (including the language files more)

  Someone at - it ideas why my laptop does not work?

  Thank you

  Greg

  Hello

  You press F11 on startup with a HP Compaq to start the recovery process.

  For problems with the recovery process, you will need to contact HP.

  BIOS problems:

  There are messages for the HP Forums for posters with similar errors:

  http://h30499.www3.HP.com/T5/notebook-HP-ProBook-EliteBook/notebook-HDD-problems-TEst-status-1-07-fail/TD-p/658902

  http://h30499.www3.HP.com/T5/notebook-PCs-pavilions-Presario/HP-Pavilion-dv8000-getting-1-07-fail-error/TD-p/883284

  http://h30499.www3.HP.com/T5/notebook-PCs-pavilions-Presario/HP-Pavilion-notebook-dv6000-1-07-fail/TD-p/1069457

  All the answers it point to a drive about to fail

  See you soon.

• Error code: 2000-0142, HDD 0-Self Test UN Succesful status 79.

  Hello guys

  I ran a Diagnostic Test on my new laptop N5010, it failed the Test of hard drive and gave this message "error Code: 2000-0142, HDD 0-Self Test unsuccessful status 79.»

  Can someone help please...

  Regarads
  

  khanisar

  Error Code 2000 - 0142, indicates a failing hard drive / failed and you need to replace it, because it is new laptop for a replacement of the hard disk, contact the Dell Technical Support and provide the error message.

  Bev.

• SMART short Self Test Failed - (error code: WHD16-8NR)

  Hi all

  I had my XPS L520X for 4 years and 2 months. I've never had a problem with its operation until last week. Randomly, it restarted and came with the PCI Realtek issue when it restarts.

  To cut a very long story short Fault find it which is going on, I reinstalled the entire operating system, including formatting of the hard drive.

  The problem of the laptop different freeze/crash and reboot with erros while doing normal tasks has not been resolved.

  I have run the Dell support center software and it shows the auto SMART test failed with the following code (error code: WHD16-8NR).

  Event log:

  Dell Support Center log file
  March 17, 2016 16:53:55
  Overall result: failed

  -------------------------------------------------------------------------------------------------------------------------------------------
  ST9750420AS [ATA:0:0\\?\ide#diskst9750420as___0005dem1#4&34e0611c&0&0.0.0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b]}
  -------------------------------------------------------------------------------------------------------------------------------------------

  Seller: Seagate
  Model number: ST9750420AS
  Serial number: 6WS100EG
  Firmware revision: 0005DEM1
  Size: 698,6 GB
  Rotation speed: 7200 RPM
  Cache size: 16 MB
  Temperature: 43 c
  Physical sector size: 4 KB
  Logical sector size: 512 B
  Count of logical sector: 1465149168
  Supported standards: ATA8-ACS, ATA/ATAPI-7, ATA/ATAPI-6, ATA/ATAPI-5
  Specification Version: Rev ATA8-ACS 4

  ----------------------------
  OS - C: [PARTITION:C\\.\C:\]
  ----------------------------

  File system: NTFS
  Volume serial number: 5087-8802
  Volume capacity: 679.00 GB
  Amount of free space: 568,63 GB
  Volume space used: 110,37 GB

  Test of the SMART State

  Test started - 17/03/2016 16:43:57
        
  Finished test:-17/03/2016 16:43:59
  Past

  Test of SMART thresholds

  Test started - 17/03/2016 16:43:59
        
  Finished test:-17/03/2016 16:44:01
  Past

  Targeted reading test

  Test started - 17/03/2016 16:44:01
        
  Finished test:-17/03/2016 16:44:05
  Past

  Try to search randomly

  Test started - 17/03/2016 16:44:05
        
  Finished test:-17/03/2016 16:44:54
  Past

  Funnel Seek Test

  Test started - 17/03/2016 16:44:54
        
  Finished test:-17/03/2016 16:46:14
  Past

  Short what SMART self-test

  Test started - 17/03/2016 16:46:14
        
  Error message:-17/03/2016 16:46:24
  The unit has reported the following State: the previous self-test completed having the read element of the test failed.
  Error message:-17/03/2016 16:46:25
  The first default LBA value is 121243744 and the failure occurred after that the device was working since 8792 hours under tension.
  Finished test:-17/03/2016 16:46:26
        Failed (error code: WHD16-8NR)

  Surface Scan Test

  Test started - 17/03/2016 16:46:26
        
  Finished test:-17/03/2016 16:47:25
  Past

  Surface Scan Test - 2

  Test started - 17/03/2016 16:47:25
        
  Finished test:-17/03/2016 16:48:58
  Past

  I also went in the BIOS BOOT MENU by pressing F12 at startup and ran diagnostics that seemed to have said everything going, however I saw a mistake, faliure in its process that was too fast for me to write the error.

  In a nutshell, my thought is that my hard drive has failed / is corrupted or is about to fail.

  My simple question is, do I need a new hard drive with the information I've provided?

  Thank you very much!

  To all those who read this topic:

  I rang Dell directly and they confirmed my hard drive needs to be replaced.

  8792 power over time, I think that its actually me good.

  Bravo and thanks for the reply ejn63

• Error hard drive Self Test 303

  Hello

  I own a HP Pavilion dm4t-3000 CTO Entertainment Notebook PC (code QA702AV).

  I did the self test HP and got the message «Hard Disk 1 303» fast

  It seems that I need to replace the HD, but I was wondering what models are compatible with my laptop and if a bad hard drive could be the source of the LAG that I lived.

  The following illustration shows what is compatible with your laptop.

  Source: Maintenance and Service of Guide for the dm4 series

  Run the long test before considering to replace the hard drive.