Error 50103 to collect data using 9229

Similar Questions

• Strange behavior when using Labview to collect data from Tektronix oscilloscope tds8200

  I hit a wall in trying to understand this one. The problem I have is that my application will not start the oscilloscope when it should.

  I use an oscilloscope Tektronix TDS8200. My goal is to collect data from the oscilloscope using Labview waveform. First of all, my program initializes and configures the oscilloscope; This part of the program works very well.

  The second part of the program begins the acquisition of data with the function 'Tktds8k Start or Stop Aquisitions.vi', which is to press the button run on the scope. The function "tktds8k to Waveform.vi" is used and should ideally return data, which I connected to a waveform playback graph.

  When I run my program, the first part runs without a problem, but as soon as the program comes to the service get the waveform, the run button in the scope, which is green when running, turns off; the program then expires, and no data is collected.

  Here is where it gets weird. I went through the debugging to try to understand this point, and I put breakpoints on the beginning and get shape wave functions so that I could scroll through the last part of the program. The program continues with the departure function, and the button run in scope is green. The breakpoint for the function get the waveform is reached and when I press on continue, turns the Run button and turns it off then back on almost immediately. data are collected, the waveform graph appears and the program ends without error.

  I thought that the timetable could be the problem, so I did the program wait as long as five seconds between the functions of start and get the waveform and that did not work. I also tried to move the start function to before the configuration functions and remove start completely; no method worked.

  is there any ideas on why, the program works when I enabled breakpoints and isn't when breakpoints are disabled? I'm sure there is an easy solution, but I was not able to find a solution.

  I have attached a pdf that contains information about the functions of the Oscilloscope (tktds8k.pdf), and I have also attached my program.

  
  

• My verse ATT modem (non apple devices to use this modem} is connected to the ATT line, Time Capsule (iPhones, Macs Time Capsule use) via ethernet Uverse.) Non apple devices can collect data from iPhones or Mac using the time Capsule?

  My verse ATT modem ({use of devices not apple wifi of this modem} is connected to the ATT line, Time Capsule (iPhones, Macs use the wifi of the time Capsule) and connect to the Uverse modem via ethernet.)

  Both devices are set to the highest security and each uses separate passwords.

  Non apple devices can collect data from iPhones or Mac using the time Capsule?

  With a bit of work by someone who knows how to do such things, not Apple computers could read some files on the Mac if file sharing is configured on the network... devices non-Apple and... He knew the device passwords or administrator for Macs.

  Mac could also play the files on other Macs if file sharing has been implemented and the device password or admin was known.

  If you ask if a PC can read the files on the Time Capsule, the answer is Yes, without doubt, assuming that the PC knew the password of device for the time Capsule.

• error 50103 in LabView using NI 6363

  Hello world

  I encountered a problem. I tried to write a Labview program in which I get simultaneous to an unstable pressure transducer and a pressure transducer. (both give voltage input signals)

  both will take place during the same time however the frequency of acquisition is different in the two cases, while trying to make 2 allowances DAQ... but when I run it displays the error 50103 allocated resource.

  So is it possible that I can consolidate all my tasks of voltage in a VI but at the same time to give different acquisition frequency (100 kHz) for unstable transducers but a frequency for the acquisition of approximately 100 Hz for the stable transducer.

  Is there a way that the two could be run simultaneously. Thnaks in advance.

  If possible just can u share the VI sample too...

  As I said, you use a sampling frequency. There is a unique clock converted on your device. This same problem has been addressed several times. Did you do a search for the reserved resources error message/code you get?

• I bought a latitude d530 use. It came with Windows 7. Site Web of Dell initially said vista wit came. It is no longer start. Error says check the data cable

  I bought a latitude d530 use. It came with Windows 7. Site Web of Dell initially said vista wit came. It is no longer start. Error says check the data cable. Sometimes, reinstall drive. I do not have the windows CD. Can I download the original Windows on android phone and the transfer

  You can download and create a bootable copy:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-windows_install?tab=question&status=unanswered

  then

  http://techingiteasy.WordPress.com/2012/04/13/how-to-activate-Windows-7-OEM-license-using-a-retail-disc/

• We get an error when I try to collect data from vCenter Server. But the Collection of Cluster works!

  Hello

  I m getting a strange errormessage when he tries to load my vCenter Server inventory.

  I have configured my vCenter Server as the endpoint server and I was able to load the Clusters. When I klick collection of data in a Cluster (Cluster of EQL 1) I can load all the data and the State is 'successful', but when I try to load the inventory FRO the vCenter Server (to get the models) im getting this error message:

  The treatment [inventory], error details error: illegal managed object reference type, folder.

  The same schows Agent logs:

  [26.08.2014 16:48:16] [Info]: start: treatment Workitem ID [2e38598e-4385-4b2d-bc88-fd2b773d1f98] [inventory]

  [26.08.2014 16:48:16] [Debug]: [[inventory]] [inventory] VirtualMachine.Admin.Hostname = vCenter

  [26.08.2014 16:48:16] [Debug]: [[inventory]] VirtualMachine.Admin.ParentIdentity = [inventory]

  [26.08.2014 16:48:16] [Debug]: [[inventory]] [inventory] VirtualMachine.ManagementEndpoint.Name = vCenter

  [26.08.2014 16:48:16] [Debug]: [[inventory]] VirtualMachine.ManagementEndpoint.Identity = [inventory]

  [26.08.2014 16:48:16] [Debug]: [[inventory]] [inventory] VirtualMachine.ManagementEndpoint.Endpoint0 = vCenter

  [26.08.2014 16:48:16] [Debug]: [[inventory]] [inventory] VirtualMachine.Admin.Name = inventory

  [26.08.2014 16:48:16] [Error]: <? XML version = "1.0" encoding = "utf-16"? >

  < Boolean > false < / Boolean >

  Error parsing [inventory], details of the error:

  System.ArgumentException: Illegal managed object reference type, folder.

  at DynamicOps.Vrm.Agent.vSphere.VSphereGetHostsRequest.ExecuteImpl)

  at DynamicOps.Vrm.Agent.vSphere.VSphereHypervisorServiceProvider.GetHosts (ManagementEndpoint managementEndpoint)

  to DynamicOps.Vrm.Agent.Collector'3.get_Hosts)

  to DynamicOps.Vrm.Agent.Collector'3.CollectManagementEndpoints)

  to DynamicOps.Vrm.Agent.CollectInventory'3.Collect)

  to DynamicOps.Vrm.Agent.BaseHypervisorAgent'3.EnumerateHypervisorResources (collector collector 3, WorkItem workItem, PropertyBagHelper propertyBagHelper)

  to DynamicOps.Vrm.Agent.BaseHypervisorAgent'3.ProcessWorkitem (WorkItem workItem, task of the chain, PropertyBagHelper propertyBag)

  to DynamicOps.Vrm.Agent.vSphere.VSphereAgentService.ProcessWorkitem (WorkItem workItem, task of the chain, PropertyBagHelper propertyBag)

  to DynamicOps.Vrm.Agent.BaseAgent.ProcessWorkitem (WorkItem workItem)

  I hope that someone had an idea, im out of ideas.

  THX Steven

  There is no data for the endpoint collection... And I'm not entirely sure of how you added the vCenter object it... y at - it a calculation object named "vCenter? To answer your specific questions about the models, however, they must be stored on a cluster that is part of the tissue group for data collection to pick them up... They are not considered as a global entity (as a resource calculation). Add models to one of the clusters and then to collect data on it, and you should be fine.

• What is error 50103? the task of DAQmx START?

  Hello

  I use cDAQ 9174 with NI 9401 to measure the period of the encoder.  I have two encoders and learned that I need to have a separate task for each.  Initially, I got an error telling me that the task was not reserved, so I followed the advice of the forum and added the TASK of CONTROL DAQmx, STORE of the value.  That eliminates the error, but now I have a new error 50103, which offers very few details of what actually is the error.  The seal is a snippet of the code, you see where there are three tasks, two tasks of meter to measure the period of encoder, and task of measurement of blood pressure, which in my opinion is not related to this error.

  Error 50103 to DAQmx controls TAsk.vi:3.

  The possible reasons: NI Platform Services: T / he said that resource is reserved.  the operation could not be performed as indicated.

  TAKS name: task _unnamed<3E>

  Thus, at the beginning, said he reserved the task, now it tells me that the problem is the reserve.  Does anyone know what this error is talking about?  The attached code is connected to a WHILE loop that aims to do a bunch of stuff with the data from the period after it was collected.

  Thank you

  Dave

  Hi dav2010,

  I modified the original example of working with the two counters at the 9174. It worked for me. Let me know if it works for you also.

  Best,

• Connection diagram DAQ Asst &amp; error 50103

  Hello LabVIEW community.

  I'm trying to integrate two different screws that require an AIGND on my SCB-100.

  The SCB-100 has two distinct AIGNDs (pinout of the 1 and 2), but in the two screws of the DAQ Asst I use, pinout 2 asks the circuit diagram for the two.

  I think that leads to a mistake of 50103 on reserved resources.

  Is it possible to switch, one of the AIGND of data acquisition for pinout 1 assistants?

  Thank you all for your help.

  Sincerely,

  The reasons are common and are totally unrelated to the error-50103. The error is because you are using two different data collection Assistants. Have you done a search here of this code or explanation? Use a simple DAQ Assistant with several channels.

• Error-50103 occurred at DAQmx control

  We strive to take into two signals in LabVIEW through our acquisition of data, and then pass them through two channels of detection of distinct peaks, however, when we try to run the program, we get the following message is displayed:

  Error-50103 occurred at DAQmx control Task.vi:14

  Possible reasons:

  The specified resource is reserved. The operation could not be performed as indicated.

  Task name: _unnamedTask<9>

  I have attached the circuit we use below, any help woud be appreciated.

  Problem solved, use:

  http://digital.NI.com/public.nsf/allkb/485201B647950BF886257537006CEB89#case4

• Error-50103 occurred at DAQmx start Task.vi:11

  Hello

  I use a nor-6008 to perform a thermal sector and I get the error "error-50103 occurred at DAQmx Start Task.vi:11 '. I have read other forums of discussion and it seems combe because I use the wizard DAQmx who don't properly resolve the resource when finsihed. I've dug further and saw that it is linked to an on-board clock synchronization problems. However, I can understand how to solve this problem.

  I thought that I create a loop that continuously monitors inputs and sometimes to interrogate the memory so I'm not kidding to the top of the clock. It's much harder to do than sounds. Can someone take a look at my code and give me some advice/suggestions to clean the DAQmx assistants.

  Thanks in advance

  Cole

  I finished by dividing my resource between the two input channels using a single assistant DAQ and dividing down the data rate and the number of samples. Works fine now.

  Big pain in the ass well.

• error 50103

  Hello

  Can someone help me please... I'm not so new to labview and never had a training. I'm trying to rea measures of the sensors of different temperature using channels NI9203 and also I am generating the output signal of NI9263. I need to know the temperature of all at the same time, but when I run labview I get error 50103. I tried all the steps mentioned on the average error of report previous but still not put my measurements.

  Please help me...

  Right-click on your data cable.  Select 'range of Signal Manipulation.  I'm pretty sure 'Split signals' will do what you want.

• error-50103 occurred at DAQmx control Task.vi:6

  I'm new to LabVIEW. I'm using LabView 8.6 and one NEITHER cDAQ-9172. For practice, I'm doing a program that takes the temperature and pressure readings and graphs.

  I don't have the modules or sensors yet, so I started by simulating a RTD temperature measurement NI9217 and a NI9237 module for the measurement of pressure.

  I created 2 while loops that run in parallel. One with an assistant of data acquisition for the temperature and the other with an assistant of data acquisition for the pressure.

  Highlight run out, when I run the program, the signal is both while loops. The temperature seems to work ok and the data graphic. The pressure, however, only goes in once, and I get the error message: "error-50103 occurred at Task.vi:6 DAQmx control Possible reason (s): the specified resource is reserved." The operation could not be performed as indicated. »

  In addition, the stop button does work on my front. I have to use the button stop in the toolbar.

  Anyone has any advice on what I can do to fix this problem or any suggestions on the best ways to address the issue?

  Thank you.

  Search the forums for error 50103.  That will tell you everything you need to know about this error code.

  For more information on your questions, post your VI so we can see what might be wrong.

• How to solve error 50103

  Dear all

  I'm trying to collect data from two sensors. The two sensors ouput is similar tension. My goal is to acquire data from two sensors can trace their waveforms, multiply the two waveforms and get the FFT.

  The error that is 50103. The image of the error message is attached. Is also attached the my block diagram.

  I read a few posts related to this error on the discussion forum. As I understand it, is that I can't run the two DAQ support at the same time. So how can I collect real-time data from two sensors?

  (NI PCI-6281 is my DAQ card and I'm collecting data continuously).

  Kind regards

  Muhammad Irfan

  Hi tronoh,.

  you still not follow our advice of setting "Of DDT" correctly output signals:

  

  You have provided different settings for these two analog signals. Check the range of the signal that is configured in the DAQ assistant...

• Error 50103 during continuous acquisition and triggering

  Hi all

  I'm ai0 data acquisition: 3 4 analog inputs (voltage) in continuous mode, display the data (tables and graphs) and data flow to TDMS files in a loop of the consumer.

  The same time, I want to be able to save "time windows" with my purchase. For example, I want to be probe ai1:2 and when the voltage exceeds a certain value, that is to say 0, 5V, I can trigger with analogue reference and get a certain amount of samples (finished samples) after and before (samples before). I am aware of how I can achieve this, an example of NOR is more useful: http://sine.ni.com/devzone/cda/epd/p/id/4840 .

  The problem is this: I don't want to stop the continuous acquisition which is already underway. If I try to start a new task (somehow "copy & paste" the example) that I get, as expected, error-50103, "the specified resource is reserved.

  So, is it possible to accomplish this task without having to fall on reserving resources problem? And if there is not a way could you suggest a way to make this front trigger and trigger sampling?

  Please find enclosed a snapshot of the code. I use a PCI-6254 with two SCB-68.

  Thank you and looking forward for you advice!

  Best regards

  Panos

  Have you seen this?

• you want to send data using labVIEW to arduino using write visa and the process and to take action using arduino. A

  I want to send data using labVIEW to arduino using write visa and the process and to take action using arduino. After that, I want to arduino to send out necessary via a serial port to labVIEW which should be read using visa read and store in a chain. While I am able to write or read both individually, I can't do it consecutively. I used advanced read and write vi for checking my code, but nothing is helping. The wrong bed 'time delay before execution. " Please let me know where I can go wrong. Also is it possible to write code for hx711 using labVIEW

  1. you need not "\n" on your orders println().  This command adds an end of line character already in the message.

  2. you get the error because you have a loop around your reading.  After the first reading (well technically, the second because of you add an extra line end character), there is nothing left in the port.  As a result, you will get the timeout.

  3. you should really consider using a Structure of the event.  This way you just don't write and read when you press the Write button and you can also use the structure of the event to make the loop to stop.  I also go up to close the port inside the stop-> value Change event.