error 5100

Just bought a 3520 MG and run maybe 10 sheets of paper and a paper jam, then, it seems that I am looking at a 5100 error. removed the sheet stuck and everything came out, but nothing will fix the error code. I've owned a lot of printers, none who dropped on me even after several years. First time I got a new printer quit on me this fast. Cleared paper jam, unplugged for 10 minutes, good guy this is a new printer!

Try:

https://support.USA.Canon.com/kb/index?page=content&ID=ART143651

Tags: Canon Printer

Similar Questions

  • Satellite 5100 - error code: 4 short Flash, 1 x long, 3 short films

    Hi all

    After I accidentally served Coke for my satellite 5100 503, it was totally cut off. My brother managed to clean it up, and it began. But shortly after, she turned to and just give this error message by flashing the power before conduit: 4 x SHORT 1 x LONG, 3 x SHORT

    I managed to interpret it using some web sites. This is a 10: 00 hex code and means: 'AC output voltage adapter's more than 16.5 V.

    And here's what they recommend, if the adapter is ok (and it is, I checked):

    After checking the connection, follow these steps:
    Check 1
    Replace the AC adapter with a new one. If the adapter does still not work, try 2 check.
    Check the box 2
    Use a multimeter to make sure the F8800 fuse on the motherboard is not blown. If not, the fuse is broken, go to 3 check. If the fuse is broken, go to test 6.
    Check 3
    Use a multimeter to make sure the F1000 fuse on the battery tray is not grilled. If not, the fuse is broken, go to 4 check. If the fuse is broken, replace the battery with a new one by following the instructions in Chapter 4.
    Check 4
    Make sure battery cables Council are well connected to PJ8820 and PJ8821 on the system board and PJ1000 and PJ1001 on the map of the battery. If they are firmly connected, go check 5.
    Check 5
    The battery or System Board may be damaged. Replace it with a new one by following the instructions in Chapter 4.

    Do you think I should go ahead and change the whole motherboard? I don't think it is a fuse, because sometimes the laptop starts and stays on for 10-15 minutes before turning off. In addition, it does not work with the battery! Only the sector...

    Thanks for you comments, but I really wonder how did you find the error code mean?
    The Satellite 5100 has been delivered with the Toshiba BIOS!
    Please note that different BIOS provide different error codes.
    This means that the 10 h error code mean Phoenix BIOS, something different than the Toshiba BIOS!

    I recommend to contact the ASP in your country and ask the details of error code.

    PS: One of my friends did the same. Shake the glass of coke on the keyboard, and the laptop has been cut.
    New bad dude... the motherboard has been replaced.

  • Dell Inspiron 5100 Blue error screen and Diagnostic test fail. Please notify.

    I don't know which article I have to go but I will try section copula.

    I was downloading the software wireless and I got the blue screen message to run the diagnostin test. For a few days I couldn't do it because everytime I turn the power on my laptop turns off after 10/12 seconds.

    Yesterday someone Advisor, I just opened the rear plastic cd/dvd and memory module cover and I was able to turn on the laptop. If I close the lid in plastic, then I wasn't able to turn on the computer laptop co I kept the lid of the box open so that I can at least put in operation and run the test.

    I got this blue screen message

    " Disable or uninstall an anti-virus disk defragmentation or backup utilities. Check the disk hard configration and check that all of the updated drivers. Run chkdsk to check for check disk hard curroption.

    Technical information.

    Stop.0X00000024 (0XF8965408, 0XF8965104, 0X001902FE, 0XF8576A27).

    VOISANP. SYS-address F8576A27 Base at F8576000, DATESTAMP 41107b6e.

    Can someone explain in English how to do all these things mentioned above in bold.

    I run the diagnosis after it and test all test except one listed below.

    EARLY DST TEST RUNS

    IN CASE OF FAILURE

    ERROR CODE: 1000-0146

    I also need help with this test. What I have to do.

    I reinstalled Windows XP again and drivers except 1 (PCI Modem, I have a problem)

    As you can tell I'm not good with laptops so I hope just that if it can be fixed easily or maybe it's time to get a new one instead of spending money on a Jules Destrooper.

    But I like the challenge of it. If anyone can help me with this.

    Thank you


  • Satellite Pro U200: BSOD error and sudden shutdown problem

    I have been using Satellite Pro U 200 since July this year.
    I had a strange problem. The problem began in mid-October where my laptop appears a blue windows error screen and restart. When the system will re-start the screen would flicker start and the operating system would not initialize correctly.

    It would give all sorts of error messages. Even if I tried to install a new operating system at this time where he would give error with the disc saying some file is corrupted. If you leave the phone turned off, it would again work normally.
    The disc would normally work on other portable computers desktop computers.

    I sent it for repair and they changed the hard drive. But the problem has returned to a degree less after a week.
    He sent again and this time they changed the motherboard.
    But the problem is now back with the blue screen stop.

    It's a Toshiba U 200 1.66 GHz memory gigabyte hard drive.
    I bought the Canada and use it in England, there is therefore a Canadian power cable.
    I am using Windows XP Pro with Service Pack 2

    Any help will be appreciated!

    Is it possible that some application you use is responsible for this? If there is an error on the corrupted file, I'm a bit skeptical about a malfunction of the equipment.

    You did some hardware upgrades?
    Check Please also this interesting article on the BSOD http://articles.techrepublic.com.com/5100-10877-6053684.html

  • Troubleshoot the Bluetooth Manager on Satellite 5100 503

    After update the latest driver bluetooth (version 3 July 2005), the bluetooth Manager will not start at all: a saying "TosBtMne.exe has encountered a problem and needs to close" error message, and no bluetooth services are available.
    Uninstalling this version of the driver and reinstall version 2 did not help - the problem remains.

    Hello ehudor

    Sorry, but I must ask you something. As much as I know Satellite 5100 503 has no Bluetooth. This device is just ready Bluetooth and. Have you built later in the Bluetooth card?

  • Replacement of motherboard on the Satellite 5100-603 - BIOS update is required?

    Hello
    I just replaced a dead card main satellite 5100 603 with a new main Board which I could get on ebay (Toshiba card system FNZSY2 - A5A000160010 P000341750-Ref.). If I boot with an installation of XP DVD it starts but hangs with the message "unexpected error (536674392) on line 1768 in D:\xpspi\base\boot\set-up\arcdisp.c".

    I realized that there are versions of different bios for various models 5100 satellite. I think I flashed the bios of 5100-603 last for this problem.
    Is this correct? (start with BART-PE from CD or HDD BART-PE raises the same error msg text in another look)

    Hello

    to get your motherboard to work you must write about the UUID (Universal Unique Identifier).
    As far as I know, you can get the UUID to a Toshiba service partner writing tool.

    Good bye

  • Satellite 5105-S702 Touch ED error during the startup process

    When I start my Satellite 5105 - S702 laptop with the v8.4.0.24 of antivirus from Computer Associates (CA) software is turned on, I get the following at the end of the boot process error message:

    Error affected

    Recovery of the THotkey failed. "
    Part took place - TouchED.exe - (THotkeyFindProc)
    Function failed - FindWindow)
    Error code: 0 x 00031402, 0x00000002

    However, when I disable the CA antivirus software and restart the laptop, I don't get the error message.

    Thus, it would seem that the CA AntiVirus software causes this error message.

    Would be grateful if someone could give advice if they have this problem with this laptop model, or the Satellite 5105-S701, or European equivalent model 5100-603, and how they have rectified it.

    Thank you

    AlanCB

    Hello

    I agree with you.
    In my view the installed (CA) anti-virus software is not fully compatible with the Toshiba Hotkey Utility or the software anti-virus doesn't recognize properly and can not handle.

    CA anti-virus does not for me but maybe you could set some parameters to ignore the Hotkey Utility from Toshiba.

    Maybe it helps if not I recommend you contact Computer Associates support team.

  • Intel Wifi 5100 found on Satellite P300-1DB

    Good afternoon!

    If anyone can, Please * HELP! *

    I just bought the Toshiba Satellite P300-1 dB, and from the moment I started, I had problems with my wireless internet connection.

    The Intel 5100 Wifi can not find the connectivity (when I know for sure that there is, because the other laptops work correctly) and
    "the error I get is" there is no network adapter/hardware installed and configured on this laptop.

    After re-booting the laptop for some time he suddenly showed that the network connectivity and I could go on the internet and everything works great.

    "The next everything was gone, no network connectivity, and is the reason why Windows is to give: there is no network adapter/hardware installed and configured on this laptop.

    I really tried everything, installation driver for Intel Wireless 5100, try to install the hardware for Intel Wireless 5100, but then it shows wireless Intel 5100 # 2 (which means # 1 is really on the laptop, but it is not found!) .

    I also tried the full restore, where to get Windows installed again, but nothing helps!

    So please if someone can, * HELP! *

    Brgds,
    Femke

    If you have the BIOS 1.80, I found a Bulletin on the Toshiba support:
    http://APS2.toshiba-tro.de/KB0/TSB8A02GW0000R01.htm

    So to do a downgrade to BIOS, and then the problem should be solved.

  • Satellite 5100/201: problem with the video card or overheating?

    HY,

    I have problems with video on a 5100/201 Satellite. It seems that when I press the left side above the graphics card or press a key on the keyboard on this side, the screen begins to be scrambled and vertical lines appear. To end Windows XP resets giving a critical error on the device and the video goes to 640 x 480. Same thing happens when you run Linux Suse 9.0.

    My question is what is the cause: map graphic damaged or overheating due to the fan not as effective as originally (my laptop is nearly two years old. Do you have someone be able to find the cause and solved the problem, also with the assistance of Toshiba?
    Any help welcome.

    Hello

    I think the problem on your laptop depends on the fan.

    A colleague on mine has a 5100-603 and had similar problems.

    The Station changed the fan.

    Good bye

  • Satellite 5100-201 and HW-Setup / Boot-PW

    Hello!

    We have a 5100 (XP SP2, just installed freshley, pilots from today at Toshiba, update the Bios from today ' hui) where it it s not possible to access HWSetup or Boot password (essential). No probs defining a super-pw protect hwsetup, change or modify the settings. no error box appears, no error is logged in the event log.

    Is the question on this matter, as the get´s a new laptop computer and we won´t release the old with a password on it.

    so, the main question is: how to clear the password.

    see you soon
    Ralf

    Hello

    You're right about the ESC key. When starting press ESC button and hold the button. Then press F1 and you will enter the BIOS settings. There, you'll be able to create your personal password.

    As far as I know that you can create the supervisor password and the user using the Console from Toshiba. Start the console and go to the Security tab.

  • Satellite Pro L510 - cannot install and start Intel Link 5100

    Hello

    I have a Satellite Pro L510 (P / N:PSLFML - 002004). Recently, I upgraded my Intel WIFI Link 5100 (my original WLAN is Realtek RTL8191SE). I tried Windows 7 32-bit and 64-bit with intel driver, version 13.4 and 13.5, non of them worked so far. I always get this error 'this device cannot start' in Device Manager

    Can someone help me with this problem please?

    Duy

    Hello

    May I ask why you switched the WLAN card? Something was wrong with your old WLAN or why you did that?

    The WLAN feature was working before the upgrade?

    I can say with certainty why you get this message error, but to me it seems that the WLAN card is not activated, you permit wireless network adapter using the FN + F8 key combination?
    ?

  • error: cannot update the 80070490

    I can't get updates because of the error code. I also have problems with certain emails. Thus, this file does not have a program associated with it for performing this action. Create an association in the set associations Control Panel. Don't know how to solve this problem.

    I also have problems with some emails that say that my security settings do not allow it to open.

    As you can tell, I'm not very smart when it comes to this computer. I am a mother grand old 61 years who just wants to communicate with family & friends without problem. Can someone help me.

    http://support.Microsoft.com/kb/958044

    You receive an error code "0 x 80070490" when you use Microsoft Update or Windows Update Web sites to install updates

    If the above does not solve it:

    Windows Update Forum:

    It's updated operating system Vista, upgraded installation and activate Forum.

    You will get the best help for any problem of Update/Service Pack in the Windows Update Forum; the link below:

    http://social.answers.Microsoft.com/forums/en-us/vistawu/threads

    When you repost here, kindly include the Error Codes, and exactly what is happening when you try to update.

    In this way, you will receive the best help.

    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

    Email problems:

    They may have been written in a program that you don't have on your computer to play with.

    need .doc or .docx Word or a Word Viewer for playback file extensions, etc, etc.
    .xls Excel need.
    need for .pps PowerPoint

    Here are the download links for free Microsoft Word, Excel and PowerPoint viewers:

    http://www.Microsoft.com/downloads/details.aspx?FamilyId=3657ce88-7cfa-457a-9aec-f4f827f20cac&displaylang=en

    Word Viewer

    View, print and copy Word documents, even if you don't have Word installed. This download is a replacement for Word Viewer 2003 and all previous Word Viewer versions.

    http://www.Microsoft.com/downloads/details.aspx?FamilyId=1CD6ACF9-CE06-4E1C-8DCF-F33F669DBC3A&displaylang=en

    Excel Viewer

    Open, view, and print Excel workbooks, even if you don't have Excel installed. This download is a replacement for Excel Viewer 97 and all previous Excel Viewer versions.

    http://www.Microsoft.com/downloads/details.aspx?FamilyId=048dc840-14e1-467D-8dca-19d2a8fd7485&displaylang=en

    PowerPoint 2007 Viewer

    Microsoft Office PowerPoint 2007 Viewer allows you to view the presentations of all the features created in PowerPoint 97 and later versions.

    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

    And here is a link to a set of free office of Applications:

    http://www.OpenOffice.org/

    How to set file Associations:

    http://articles.TechRepublic.com.com/5100-10878_11-6172036.html

    How do I... Change file extension associations in Windows Vista?

    See you soon.

    Mick Murphy - Microsoft partner

  • Canon pixma 3500 error message

    There is a paper jam.  I cleared the jam, but get the 5100 error message and cannot print.  How can I fix it?  Is the broken primter?

    Help, please!

    Hi joann1,

    It is recommended that you contact the direct technical assistance. There is NO charge for this call. Information in real-time to a technical assistance call live would be very beneficial in this case.

    Please call 1-866-261-9362, Monday - Friday 10:00-10: 00 ET (excluding holidays). A Canon technical support representative will be able to solve this problem more quickly.

  • My laptop Dell Inspiron 5100 has started incompatible.

    My laptop Dell Inspiron 5100 has started an on again off again behavior.  If I stopped and try to restart it (by switch or auto reboot), it does not restart.  I get a metal "beep" of the machine.   If I'm persistent and try several times with the button, it can restart, but not always.  I thought it might be the start / stop switch had become sensitive to heat or was dying, but even when it is completely cold, not connected to an external power supply and since 3 + hours, it will still manifest this strangeness.  Any suggestions?   I am running Windows XP Pro and McAfee on this system.  I realize that it is an older machine, but I really like XP, and want to continue to use this set up if possible.

    Hi Bugysmom,

    Look in the event viewer to check if there is no related error message or error code related this topic.

    For more information, see:

    Using the event viewer        

    Write help us with the State for us to best help you.

  • blue screen error STOP: 0X000000ED (OX86791240, 0XC000009C, 0x00000000, 0x00000000)

    When I try to start my dell inspiron 5100 laptop with windows xp I get a blue screen with the error UNMOUNTABLE_BOOT_VOLUME with the error code Stop: 0X000000ED (OX86791240, 0XC000009C, 0x00000000, 0x00000000) is there anyone to the solution?

    How your post is related to the Windows Update feature?

    Bug Check 0xED: UNMOUNTABLE_BOOT_VOLUME:
    http://msdn.Microsoft.com/en-us/library/ff560355 (vs.85) .aspx

    ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

Maybe you are looking for