error code 19; TSSTcorp CD/DVGW TS-H652M ATA Device will not load at startup upward due to incomplete or registry problem? What can I do from here now, Windows VISTA-32 bit; gives this code problem also 00000013, thanks for your time.

Similar Questions

• Driver TSST Corp CDDVDW TS - L633L ATA Device will not load. The problem code is 19 / how to fix?

  HP Pavilion dv4
  TSST Corp CDDVDW TS-L633L ATA Device

  Control Panel / problem report and solutions
  Problem: Could not load software driver status: sent report

  Description
  Windows was able to successfully install device driver software, but the driver has encountered a problem when he tried to run. The problem code is 19.

  Signature of the problem
  Problem event name: PnPDeviceProblemCode
  Architecture: x 64
  Hardware ID: IDE\CdRomTSSTcorp_CDDVDW_TS-L633L___0400___
  Configure the class GUID: {4d36e965-e325-11ce-bfc1-08002be10318}
  The PnP problem code: 00000013
  Driver name: cdrom.sys
  Driver version: 6.0.6002.18005
  Driver date: 11/04/2009
  The system version: 6.0.6002.2.2.0.768.3
  Locale ID: 1033

  Additional information about the problem
  Bucket ID: 619663520

  Control Panel / Device Manager
  Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 19)
  Click on 'Search for solutions' to send data about this device to Microsoft and to see if there is a solution available.

  I tried:
  Update driver software
  Uninstall / find the hardware changes
  Uninstall / reboot / new hardware found
  Properties / verification solutions

  How can I fix it?

  Hello

  Try to follow the procedure at the title of the subheading "Let fix me it myself" on the link below to delete the upper and lower filters and see if that helps the issue.

  http://support.Microsoft.com/kb/982116

  You have to restart the laptop after that.

  Kind regards

  DP - K

• CD/DVD drive is not detected (Windows Vista). Error message: Please insert a disk (removable disk): __Our device driver is: TSSTcorp CD/DVGW TS-H653L ATA Device.

  Was not aware there is a problem until I tried some recently audio and data CDs.  Have you tried different Web sites to help you, however some of the directions come with a warning that by following certain procedures I can create other problems.  The FixIt tool was not able to install the player.

  Hello

  Please ALL these even if you've done it before as it's often the total process that
  solves the problem. You should also check with the system manufacturer as some readers do not use windows
  by default the drivers and need their own, use the bottom and if no joy check on the site of the manufacturer of the system.

  Try this - Panel - Device Manager - CD/DVD - double-click on the device - driver tab - click
  Update the drivers (this will probably do nothing) - then RIGHT click the drive - UNINSTALL - REBOOT
  This will refresh the default driver stack. Even if the reader does not appear to continue below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a loose cable or
  slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during the installation of Windows Vista after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Hope these helps.
  Rob - bicycle - Mark Twain said it is good.

• Since El captain of loading, I can't open Photoshop & Lightroom 2015 CC all it gives an error of '1 '. Have reinstalled, vacuum cleaner used, but will not load showing only error

  Since the El Captain on MacPro 2.8 Ghz Tower loading, I can't open Photoshop and Lightroom 2015 CC all it gives an error of '1 '. Have reinstalled, vacuum used but still does not load only showing error '1' someone to solve?

  See you soon,.

  John Frost

  Error code 1: "unable to install". Creative Cloud Desktop: https://helpx.adobe.com/creative-cloud/kb/failed-install-creative-cloud-desktop.html

  https://forums.Adobe.com/message/7533806

• What is the correct procedure to upgrade Windows Vista 32 BIT to Windows 7 home one '?

  I'm running Windows Vista Home premium 32-BIT.

  I bought the upgrade disc to install Windows 7 Edition home premium.

  Where can I find a procedure step by step to install the upgrade?

  Hello

  This is a very good guide for what you want to do:

  Make sure you go from Vista 32 bit to Windows 7 32 bit to be able to do an upgrade.

  «How To Upgrade from Vista to Windows 7 Edition Home Premium»

  http://www.howtogeek.com/HOWTO/6892/how-to-perform-an-upgrade-from-Vista-to-Windows-7/

  Make sure that you first run the Windows 7 Upgrade Advisor:

  Run the "Windows 7 Upgrade Advisor.

  http://www.Microsoft.com/en-US/Download/details.aspx?ID=20

  Check if your specifications are compatible for Windows 7:

  "Windows 7 system requirements"

  http://Windows.Microsoft.com/en-us/Windows7/products/system-requirements

  "Windows 7 Compatibility Center" for software and hardware:

  http://www.Microsoft.com/Windows/compatibility/Windows-7/en-us/default.aspx

  See you soon.

  Edit:

  Go to your computer / computer laptop manufacturer Web site and see if Windows 7 drivers are available for your make and model computer / laptop.

  If this is not available, Windows 7 will not properly work for you.

• Code 10 made his first appearance for my tsstcorp cd/DVGW-ts-l632d ata device

  cannot burn discs on my laptop

  Try following the steps under "Windows 7 or Windows Vista" in the MS KB article:

  http://support.Microsoft.com/kb/982116

  These measures, to remove the UpperFilters and LowerFilters, values if they exist, in the registry key named can help.

  Create a System Restore Point beforehand and restart the computer later.

• The 'Search' function on the start menu does not work. It seems to freeze and will not even close until I have shut down the computer. What can I do to correct this situation?

  I tried to use the "Search" function to locate a specific file.  The computer froze... not allow me to cancel when I realized that it wasn't working.  The only way I could get the closing of the window had to shut down the computer.

  Hi DyleAcker,
   
  -Search function work is no problem earlier?
   
  Run the troubleshooter from the link given below and if it helps to fix the problem:
  Fix Windows Search when it crashes or shows no results

• Lightroom 4 will not open. It is said that he met a problem when she opened the last time. It says it fixed itself, but it does not. What should I do?

  It is said that he met a problem when previewing and it will fix itself the next time, but it didn't. I even tried to reinstall. Help!

  Hi korrinr,

  It seems to be a problem with the preview cache.

  Navigate to the location of your Lightroom catalog via finder/File Explorer and get rid of the Previews.lrdata folder suggest you (do not delete the .lrcat file)

  Kind regards

  Claes

• Windows vista 32-bit update service pack 1 error 80073712 when I try to install.

  I tried and tried to install the updated Windows vista 32 bit service pack 1, but also try to update manually, however I continuously get the update error 80073712. I tried the scan tool update service, troubleshooting automatic on the Microsoft Support Web site, as well as research on the Microsoft Answers site for more assistance. However, I still have the same problem, then what else could be the cause so many dell used laptops for not updating this service pack. Either way, I haven't installed service pack 2 either, as I mentioned on some of the answers.

  Microsoft says that the operating system is corrupt, so SP1 or SP2 fails. Follow this link for repair.

  https://support.Microsoft.com/en-us/KB/957310#/en-us/KB/957310

  In addition, the article is ok, but he fails to mention that, after analysis of the Sfc runs, must complete the process.

  It is, done Sfc, you must also type: CHKDSK C: /F agree to restart, type: EXIT

  restart the pc... When the computer reboots, the repairs are installed/fixed, w/o this cmd, just retry the update is not

  possible, installations/repairs, can take place only when the pc is restarted...

• Can I upgrade Windows Vista 32-bit to Windows Vista 64 - Bit and preserve everything?

  I have a computer with Windows Vista 32 - Bit OS.  I have also 4 GB of RAM, but as the OS is 32-bit, he acknowledges that 3 out of 4 GB.  So, my question is, can I upgrade to a version 64 bit Vista and preserve files and programs, or what I have to buy a copy of Windows Vista 64-bit?

  Thank you

  Hello.

  No.; You cannot switch from 32-bit to 64-bit.

  It must be done with a new installation of the 64-bit operating system.

  There has never been a way to upgrade.

  You should backup your data, copy it into the 64 bit OS and reinstall all your programs

  Microsoft sells more than Vista.

  And before you buy Windows 7:

  Go to your computer / computer laptop manufacturer Web site and see if Windows 7 drivers are available for your make and model computer / laptop.

  If this is not available, Windows 7 will not properly work for you.

  Run the "Windows 7 Upgrade Advisor.

  http://www.Microsoft.com/en-US/Download/details.aspx?ID=20

  Check if your specifications are compatible for Windows 7:

  "Windows 7 system requirements"

  http://Windows.Microsoft.com/en-us/Windows7/products/system-requirements

  "Windows 7 Compatibility Center" for software and hardware:

  http://www.Microsoft.com/Windows/compatibility/Windows-7/en-us/default.aspx

  And the Microsoft Store where you can get an idea of the price of Windows 7:

  http://www.microsoftstore.com/store/msstore/en_US/list/CategoryID.50726100

  See you soon.

• I get this error code 0x800cccof also 0x800cccD2 in Windows Live Mail.

  I get this error code 0x800cccof also 0x800cccD2. Can someone give me the info, I need to solve this problem?  Thank you

  Hello

  The question you have posted is related to Windows Live and will be well suited in the instances of Windows Live. Click on the link below.

  Windows Live Solution Center

  http://www.windowslivehelp.com/product.aspx?ProductID=15

• error code 148,3 getting license for this product has stopped working

  error code 148,3 getting license for this product has stopped working

  Hello

  Greetings!

  See this article: https://helpx.adobe.com/creative-suite/kb/error-licensing-stopped-windows.html

  Concerning

  Jitendra

• I am unable to boot into windows vista 32-bit, so I downloaded the vista recovery disk and get an oxo error code what it means?

  Windows recovery disc 32-bit error code meaning version question

  Hello
  I hope someone can help me. I am unable to boot into windows vista 32-bit, so I downloaded the vista recovery disk and get an oxo error code what it means (thanks in advance)?

  You don't give any info on what was the original problem with the computer.

  You have set the Bios Setup to boot from the CD/DVD drive?

  At startup, it will say press F2 or delete key to go into Bios/Setup, or maybe F12 to go to the Start Menu.

  And have you tried also to tap F8 at startup and choose Safe Mode from the list of Boot Options?

  Use up arrow key to do this, press on enter.

  Browse your Hard Drive manufacturer's website, download software from here and test your hard drive for errors.

  See you soon.

  Mick Murphy - Microsoft partner

• get the 0x400110020000100b error code while making the recovery of the system for windows vista 32 bit.

  I tried to do a system restore on my laptop using the included recovery disks and had this error 0x400110020000100B. The drive looked pretty beaten last week so I ordered a new series. Now, when I got to put disc 2 in (to 80% full) I get the same error.  I called customer service and he took me through the process of F9, nothing works and I also tried the F11 approach that made me not the case.  I'm frustrated because I don't really have the money for a new laptop computer.

  Laptop is a HP Pavilion DV6700.

  Any help would appreciated more than you know.

  The system is Windows Vista 32 bit

  The guy on the phone said ' well, you know it's a pretty old computer... Thank you gee...

  Hello:

  See if you can make your own Vista installation disc if you can read the product key 25 character on the bottom of your laptop.

  Here's how:

  If you are in a fault light but rewarding you can do yourself if you can read your product key of Vista on the PC of 25 characters.

  You just download the 3 files you need on the link below and read all the instructions to create a Setup bootable DVD disk using imageburn.

  Do not take into account the part of the text in the first screen shot about "extract the files in the folder of Vista."

  The files were extracted already in this folder when you ran the X14.exe file by reading the text on top of the first screenshot.

  The other thing I noticed is on the 4th page, where it shows Developer ID Microsoft Corporation. I had to type Microsoft Corporation in me, and then other codes already filled in.

  When I went to compile the ISO file, ImageBurn gave a message on a WIM file, file and ISO, and if I wanted to burn it in a different format.

  I selected no, make the ISO file.

  It was not so hard to do. I burned both the disk of 64-bit and 32-bit disk in case I ever need them.

  I tested both of them one my hp dc7100 CMT desktop PC, worked flawlessly.

  When you enter the product key, he knows which version of Vista you have.

  http://en.community.Dell.com/support-forums/software-OS/w/microsoft_os/3317.2-3-Microsoft-Windows-v...

  After you install Vista successfully, you can then install the drivers for your PC and driver page support.

  Paul

• Error Code 8E5E0147. Platform update for Windows Vista (KB971644) update for Windows Vista (KB973917) update for Windows Vista (KB976470) fail to install.

  This problem lasts for a long time and I'd like to update my Windows Vista.  Thank you for your time.

  Hello, I sent an email before for support, but I have no answer at all so I tell myself I'll try to ask my question here.
  I get the following error code (Code 8E5E0147) whenever I try to install the following updates for Window Vista.
  Update for Windows Vista (KB971644) platform
  Update for Windows Vista (KB973917)
  Update for Windows Vista (KB976470)

  What application or antivirus security suite is installed and your current subscription?  What anti-spyware (other than Defender) applications?  What third-party firewall (if applicable)?

  A (another) Norton or McAfee application has already been installed on the computer (for example, a free trial version which is preinstalled when you bought it)?

  See this previous discussion about this error: http://social.technet.microsoft.com/Forums/en/itprovistasetup/thread/5d5084ec-78f6-427c-a146-91fcf72e3616

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft