Error code 28: could not find the drivers. Windows 7 64 bit could not find the drivers for my Seagate Expansion Portable Drive. The same system works for another 32-bit version of windows 7.

Similar Questions

• Seagate expansion portable drive not seen on my linksys x 3500

  Plugged into a disk Seagate Expansion Portable 1 TB srd00f1 to my new Modem - Linksys router X 3500, but he can't seem to upward and when I looked at the on the network, it was confirmed that there is no drive present someone at - he had thoughts

  I recommend that you contact the Mfr of that drive for a good use and configuration of the drive is implemented well. Check if the external power supply is required.

  Consult the training set up manual and configuration on routers web page. Formatting NTFS is recommended on the disks.

  http://support.Linksys.com/en-MEA/support/gateways/X3500

  I recommend phone by contacting your regional Linksys supportoffice to see if the disc is officially supported on the x 3500 and ask questions on installation and configuration.

• I can't uninstall the old Java version 6 update 29. I get a "error code 1606: could not locate the directory."

  I am running Windows XP SP3, I can't uninstall the old java version 6 update 29, I get a "error code 1606: could not locate the directory... fatal error" How can I remove the old version of java?  I tried to uninstall regedit.exe, javaRa and windows unsuccessfully capability.  I uninstalled java, deleted the program file, but the version 6 29 poster update still in the program directory.  Help, please!

  original title: uninstall older versions of Java
  Hello
   
  Method 1:
  Check out the link and follow the steps.
   
  After uninstalling Java, how to remove its entry in the windows?
  http://www.Java.com/en/download/help/regkey_addremove.XML
   
  Method 2:
   
  See the article and follow the steps.
   
  Error message when you install a program: "Error 1606. Could not access the network location. "All the users\ directory '
  http://support.Microsoft.com/kb/315352
   
   
  Method 3:
  Check out the link and follow the steps.
  
  Download errors: 1305, 2755, 1606, etc..
  http://www.Java.com/en/download/help/error_installshield.XML
  Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: 322756 (http://support.microsoft.com/kb/322756/ ) how to back up and restore the registry in Windows

• I tried to install since 11/12/09 important update KB976098 and continue to get error code 8E5E03FB unknown error. I tried to find the error code, but can't find it. How can I download and install this update?

  I tried to install since 11/12/09 important update KB976098 and continue to get error code 8E5E03FB unknown error.  I tried to find the error code, but can't find it.  How can I download and install this update?

  Quote your full version of Windows (for example, WinXP SP3;) Vista SP1; Vista 64 - bit SP2; Win7; Win7 64 bit) when you post in a forum or a newsgroup. Please do it in your next reply.

  Short story: If you do NOT live in one of the zones listed in http://support.microsoft.com/kb/976098, you really need not to install this security update not any way so you can hide it just ("don't show me this update"). ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• My photoshop will not update, it gives me an error code that is not listed.  The error code is U44M1P34

  I tried several times now to do the last update for the application of CC of Photoshop 2015, it will not install.  It gives me an error code that is not listed in the list that I found in the help section.  I hope that someone else has had this problem and knows what it is before I have to call and find someone who can give me only one I can't answer.

  Please check: U44M1P34 error message

• I get the error Code: ORA-01008: not all variables

  Hi all
  
  When I try to insert data into a table through the procedure am getting following error...
  
  Error code: ORA-01008: not all variables.
  
  But if I run the same query on the outside passing the parameters it works well. When I run the Insert through the procedure statement, I don't get all the variables related error.
  I'm passing two numbers as parameters. But I don't know why I get this error.
  
  Could someone suggest me please.
  
  
  
  Thank you
  Sree

  http://lmgtfy.com/?q=ora-01008%3A+not+all+variables+bound.

  Good bye
  DPT

• Creative installation Cloud 42 error code: Installer could not access critical file / folder.

  Creative installation Cloud 42 error code: Installer could not access critical file / folder. I thought that the problem was related to permissions. But after changing the permissions administrator and user always the same error message. How can I fix? Help much appreciated.

  Help for the Download & Install & Setup & Activation

  -Cat http://www.adobe.com/support/download-install/supportinfo/

• error code 80070490 could not be updated. 11-09 has been updated. I'm trying to update but it fair to say that try again with error code nothing changed on my computer. I'm pretty new to this. can someone help me please

  error code 80070490 cannot install windows update.

  Ken,

  0 X 80070490 - ERROR_NOT_FOUND

  Corrupted system file.  You will need to perform an upgrade on the spot or reinstalling the operating system.

  Ignore the title: Some Windows Vista functions may not work, or Windows Vista may stop respondinghttp://support.microsoft.com/kb/929833

  A repair install is that the usual of SFC/scannow solution does not work.

  You receive an error code "0 x 80070490" when you use Windows Update or Microsoft Update Web sites to install updateshttp://support.microsoft.com/kb/958044

• Error code 0 x 80070035 that the network path was not found.

  OT: error code 0 x 80070035
  My wife and I have 3 computers all running Win 7 64 bit. Two jobs and the third is a laptop. My desktop or laptop computer I can access any folder of each machine. However, when I try to click on my wife under 'Network' computer I get the message "Windows cannot access\\wife_desktop." When I click 'See details' it displays "error code 0 x 80070035. The network path was not found. "I'm running out of things to try.  I tried to use my desktop computer and notebook to help me check the installation on my wife's computer. I have updated owner and security settings in both car and system, as well as temporarily disable the firewall. Any suggestions would be greatly appreciated.

  Hello

  Method 1: Run the network troubleshooter and check out what he has to say.

  See the links below:
  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7
  http://Windows.Microsoft.com/en-us/Windows7/open-networking-troubleshooters
  http://Windows.Microsoft.com/en-us/Windows7/use-Network-Troubleshooter-event-logs-to-solve-network-problems

  Make sure network discovery is enabled on the laptop computer, by default the State network discovery is disabled. If network discovery is off, please take the following steps to turn on.

  (a) click Start.
  (b) click on Control Panel.
  (c) click on network and sharing Center.
  (d) click on the arrow to drop down next to the network discovery.
  (e) click on the option, turn on network discovery.
  (f) click on apply.
  http://Windows.Microsoft.com/en-us/Windows7/enable-or-disable-network-discovery

  Method 2: The question can be caused also by your security program such an antivirus or a firewall of Windows /Defender that can have conflicting parameters as to not not to perform certain tasks. I suggest you temporary disable antivirus and firewall and check the result again. You must activate new security that you was disabled programs.

  http://Windows.Microsoft.com/en-us/Windows7/turn-Windows-Firewall-on-or-off 
  http://Windows.Microsoft.com/en-us/Windows7/disable-antivirus-software

  See the following link: http://social.technet.microsoft.com/Forums/nb-NO/w7itpronetworking/thread/028a3d13-f571-49e0-abe7-1ca61fb92082

• error code 0 x 80070005 advises the downloads of updates 8-11 failed.pls.

  updates of windows 8-11 could not download, all 5. error code 0x80070005.

  Error code 0 x 80070005 is also described as ACCESS DENIED (you may not to install updates)

  Please check that you are logged into an account with administrative privileges.

  Can I infer that you are using Vista? If your antivirus software does not interfere it guilty in your update course, then see the following coming from my notes available on this site.

  "Please follow these instructions if you are experiencing this error code during checking or install updates via Windows Udpate. What follows applies only to Windows Vista.

  1. Download AccessChk (Sysinternals).  This tool allows you to assess the level of access of some users or groups of resources, including files, directories, registry keys, global objects and Windows services.  Here is the link to download the tool: http://technet.microsoft.com/en-us/sysinternals/bb664922.aspx

  2. save the zip on your desktop and extract the file:
  -Right-click on the file and select extract all...
  -Click Next when prompted for the Destination.

  Therefore, you should see a folder called AccessChk on your desktop.

  3. open the folder AccessChk

  4 press and hold the shift key and right-click in the window.  Select "open here command prompt.

  5. a command prompt window should open a similar message:
  C:\Users\\Desktop\accesschk >

  6. type the following command and press ENTER:
  "" AccessChk.exe "nt service TrustedInstaller" s - n k ' hklm\software\Microsoft\Windows\CurrentVersion\Component Based Servicing "> accesskchk.txt
  Tip: You should be able to copy and paste the command into the command prompt.

  7. close the command prompt window.  Open the Accesschk folder on your desktop (if it has been closed).

  8. double-click on Accesschk.txt (text file), it should open Notepad.

  If this is insufficient,

  1 if please download the subinacl.msi from the following link and save the patch to installation on the desktop:
   
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=e8ba3e56-d8fe-4A91-93Cf-ed6985e3927b&displaylang=en#AffinityDownloads
  SubInACL (SubInACL.exe)
   
  2. go to your desktop and double-click on the downloaded file.
  3. Please select the C:\Windows\System32 folder as the Destination folder during installation. Later, we will use this tool to reset the permissions on the current computer settings.
  4. click on the button 'Start' in the 'Search' bar type: "Notepad" (without the quotes) and press ENTER.
  5. copy the following commands, and then paste them into the opened Notepad window:
   
  off @echo
   
  Subinacl /subkeyreg HKEY_LOCAL_MACHINE/Grant = administrators = f
  Subinacl /subkeyreg HKEY_CURRENT_USER/Grant = administrators = f
  Subinacl /subkeyreg HKEY_CLASSES_ROOT/Grant = administrators = f
  Subinacl % lecteur_systeme % /subdirectories / Grant = administrators = f
  Subinacl /subkeyreg HKEY_LOCAL_MACHINE/Grant = system = f
  Subinacl /subkeyreg HKEY_CURRENT_USER/Grant = system = f
  Subinacl /subkeyreg HKEY_CLASSES_ROOT/Grant = system = f
  Subinacl % lecteur_systeme % /subdirectories / Grant = system = f
   
  @Echo =========================
  Completed @Echo.
  @Echo =========================
  @pause
   
  6. After you paste the above commands, please close the Notepad window. Choose "Save" when you are prompted to save the file. Type "reset.bat" as the file name and choose "Desktop" in the Panel on the left as the save location.

  7. refer to the desktop and right click the reset.bat file, then choose "Run as Administrator".

  8. you will see a window of type BACK treatment.
   
  NOTE: It may take several minutes, please be patient. When it is finished, you will be prompted with the message: "finished, press any key to continue."

  Note: On some driver update installation procedure, we also received this error code, please redirect this kind of case to the Team System Vista, because it can be considered for structure of third-party programs.

  Look for updates after that.

  Hope this information is useful.

  This problem may be caused by third-party security programs such as firewalls and antivirus software. You can disable or remove to check the issue.

  From: Microsoft Answers Support Engineer
  http://social.answers.Microsoft.com/forums/en-us/vistawu/threads "

  TaurArian [MVP] 2005-2011 - Update Services

• SCardUIDlgSelectCardW returned unexpected error code, 0x8010002e, impossible to find a card reader chip.

  Event ID error msg:

  Log name: Application
  Source: Microsoft smart card CSP
  Date: 2010-06-29 22:25:22
  Event ID: 0
  Task category: no
  Level: error
  Keywords: Classic
  User: n/a
  Computer: Acer
  Description:
  The description for event ID 0 in source Microsoft smart card CSP is not found. Either the component that triggers this event is not installed on your local computer or the installation is corrupted. You can install or repair the component on the local computer.

  If the event is on another computer, the display information had to be saved with the event.

  The following information has been included in the event:

  SCardUIDlgSelectCardW returned unexpected error code, 0x8010002e, impossible to find a card reader chip.

  the message resource is present, but the message is not in the string/message table

  Title: event ID of origin 0

  The event XML:
  http://schemas.Microsoft.com/win/2004/08/events/event">
   
     
      0
      2
      0
      0 x 80000000000000
     
      68716
      Application
      Acer
     
   
   
      SCardUIDlgSelectCardW returned unexpected error code, 0x8010002e, impossible to find a card reader chip.
  
   
  

  Your question of Windows Vista is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the Technet Windows Vista Security Forum

  Lisa
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• error code 259 does not correctly updated to sp62736.

  I have a Hp Pavilion 500-141ea im trying to update the IDT audio driver for windows 8, I supported SP sp62736, it passes through the installation procedure, then it stops and comes up with this error code 259 does not correctly updated, I even disabled etc still the same antivirus software.

  Any idea?

  Hi Apache1968,

  If everything works at the moment, with the exception of downloading then I would leave it as it is. The whole "don't mess with what works" thing.

  Thank you

• Error Code D59 can not install Microsoft SQL Server 2005 Express Edition Service Pack 4 update (KB2463332) _

  Error Code D59 can not install update of Microsoft SQL Server 2005 Express Edition Service Pack 4 (KB2463332)

  Try posting in the SQL Server Setup & Upgrade forum for assistance:http://social.msdn.microsoft.com/forums/en-US/sqlsetupandupgrade/threads/>

• I get the error code 646 when I try to install windows updates.

  I get the error code 646 when I try to install windows updates. I have Windows Vista Home Premium. I disabled my firewall and I still get the error code 646.

  Hello

  Try this 1st to see if it helps, and it should:

  Description of the Patch registration cleanup tool
  http://support.Microsoft.com/kb/976220/

  ------------------------------------------------------

  If necessary :

  Try this - Panel - Windows Updates - on every update that will not be installed - click on the important updates
  or the update itself - double click a view more information (or click top then discovers on the right)

  Those who will take you to a page where you can download the update.

  Or go here and the KBxxxxxx number to download it.

  Download Center - mount the KBxxxxxx.

  Microsoft Download Center
  http://www.Microsoft.com/downloads/en/default.aspx

  Download - SAVE - go to where you put them - click on - RUN AS ADMIN

  Then you can right click on the update in the updates Windows and HIDE.

  If you get an error Installer install this version:

  Windows install 4.5 Redistributable
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=5A58B56F-60B6-4412-95B9-54D056D6F9F4&displaylang=en

  ----------------------------------------------------

  Then run this:

  How to reset the Windows Update components? -a Mr Fixit
  http://support.Microsoft.com/kb/971058

  Description of the system for Windows Vista, Windows Server 2008, update tool and
  for Windows 7
  http://support.Microsoft.com/kb/947821

  ------------------------------------------------------------
  Because these are all Office updates you might get more information if necessary in the Agency of those groups that
  may have experienced the same problem.

  Office newsgroups
  http://www.Microsoft.com/Office/Community/en-us/FlyoutOverview.mspx

  Microsoft.public.office.misc discussions
  http://www.Microsoft.com/communities/newsgroups/list/en-us/default.aspx?DG=Microsoft.public.Office.misc&cat=en_us_01cb749f-c998-4762-8099-df71793c11c7&lang=en&CR=us

  ------------------------------------------------------------

  If necessary you can incident free get reports however the above should take care of it for you.

  Windows updates - free Incident report

  Go here and click on-> Windows Update fails while searching, downloading or installation of updates
  http://support.Microsoft.com/GP/wusupport#tab3

  The security updates, you can get free support Incident report
  http://www.Microsoft.com/protect/resources/support.aspx

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• error code message appears not

  Hello

  I tried to create a set of labview error codes codes using the tools-> edition of error codes.  Has created some test errors and saved the file

  C:\Program NIUninstaller Instruments\LabVIEW 2009\user.lib\errors

  The file called test - errors.txt appears as follows:

  
  
  
  First file of Sean error code
  
  
  Unstable device
  
  
  Unstable critical apparatus
  
  
  Press Stop or device will begin the countdown to destruction
  
  
  Destruction began the countdown, all organic life will be destroyed with a radius of 2 miles in t - 10 minutes
  
  

  

  Then, I designed a simple VI to test the error codes, see the attachment.  However, the error message do not appear in the error on the source area.

  Does anyone know why LabVIEW is not recognizing my error codes?

  Rgds,

  Sean

  David,

  The data cluster error type may not contain the actual description of an error.  When an error is generated, only the cluster of error data will be the error code, status and source.  The source must contain the path calling of the VI that generated the error, not the description of the error.  It is recommended to use the VI Simple or General Error Handler to programmatically display the short description of the error.  If you want to interactively view the description you can right-click on a cluster of error control or indicator and select 'explain the error.

  Chris M