error code - 40 in teststand deployment

I just got a new laptop and installed all the products NOR including TestStand I had in my old laptop. Using the same deployment file I had on the old laptop, I run the deployment utility and get the following errors.  What I am doing wrong? :

From newspapers.
Done processing environment file
Analysis completed
Building...
15:34
An installer is being created.
Loading information of product deployment
 
**************
Error: Internal error. (Error code - 40)
There was a problem, the information on the source of product 'NOR DataFinder Destop Edition' distribution
Final report of the error
**************
 
 
WARNING *.
Deployment information of a product not identified to jump because the-40 error code occurred while loading file: C:\Program NIUninstaller Instruments\Shared\MDF\Manifests\NI, Destop DataFinder edition {7D5297CE-E2B6-458C-91F4-47F674A94A8F} .xml
 
 
**************
Error: Internal error. (Error code - 40)
There was a problem, the information on the source of product 'NOR DataFinder' distribution
Final report of the error
**************
 
 
WARNING *.
Deployment information of a product not identified to jump because the-40 error code occurred while loading file: C:\Program NIUninstaller Instruments\Shared\MDF\Manifests\NI DataFinder {D6B1E623-A952-421A-9C50-1958A056C63B} .xml
 
 
**************
Error: Internal error. (Error code - 40)
There was a problem, the information on the source of product 'NOR DIAdem' distribution
Final report of the error
**************
 
 
WARNING *.
Deployment information of a product not identified to jump because the-40 error code occurred while loading file: C:\Program NIUninstaller Instruments\Shared\MDF\Manifests\NI tiara {2C52C774-1B40-4848-95EF-735D22EF9203} .xml
 
 
**************
Error: Internal error. (Error code - 40)
There was a problem, the information on the source of product 'NOR DIAdem' distribution
Final report of the error
**************
 
 
WARNING *.
Deployment information of a product not identified to jump because the-40 error code occurred while loading file: C:\Program NIUninstaller Instruments\Shared\MDF\Manifests\NI tiara {3CB2BF3F-9C33-477B-8D99-251491541ED1} .xml
 
 
**************
Error: Internal error. (Error code - 40)
There was a problem, get information on the source of product 'SignalExpress Steps' distribution
Final report of the error
**************
 
 
WARNING *.
Deployment information of a product not identified to jump because the-40 error code occurred while loading file: C:\Program NIUninstaller Instruments\Shared\MDF\Manifests\SignalExpress steps {84172037-613A-4B72-B797-E36C04BA5D17} .xml
 
 
**************
Error: Internal error. (Error code - 40)
There was a problem obtaining information on distribution product source 'SignalExpress_App '.
Final report of the error
**************
 
 
WARNING *.
Deployment information of a product not identified to jump because the-40 error code occurred while loading file: C:\Program NIUninstaller Instruments\Shared\MDF\Manifests\SignalExpress_App {8169D9AA-A2DE-4EA0-BF27-2E7D1CF52D87} .xml
 
Adding files to install
Makes adding files
Preparing to build the deployment
Copy of the products of distributions
Deployment of building
Copy of the configuration files
Merged configuration database information
Definition of product information
Information for the developer settings part
Final construction of departure
 
**************
Internal error: A tool or the library returned an error. (Error code - 21)
Error messages
Error: Party to the path "c:\documents and settings\all users\application data\national instruments\mdf\productcache\ni c interface to labview [1.0.1]\lvcinterface\lvcinterface.msi" was registered by 2 products: "NI LabVIEW C Interface" and "NI LabVIEW C Interface.

Final report of the error
**************
 
Deployment of the completed building
Internal error code-21 a Setup program is being created.
The Setup is completed
Construction is completed
15:35
Abandoned

HPatel,

I found more information about your error code.

When you generate a deployment, you have the option to cache information about the installation additional programs that include you in your deployment, if you do not have to insert the disc every time.  This error code means that the deployment utility is looking for cached information to add to your additional installers, but it is not.  Clear all your records of cache (C:\Program NIUninstaller Instruments\Shared\ProductCache or C:\Documents and Settings\All Users\Application Data\National Instruments\MDF\ProductCache) and build again.  The deployment utility must ask any disk must be added to the installer, and it will create a new cache.

Tags: NI Software

Similar Questions

  • TestStand deployment error Code 1055 when using LabVIEW storage VIs

    After a few days of playing with TestStand deployment. I have final stalked the VI which was the origin of this error.

    He was using the LabVIEW storage screw to save data in a TDM file.

    My work around at the moment is to use a Wrapper VI and call this VI by reference.

    In this way the deployment TestStand cannot detect the Sie of storage.

    I'm using LabVIEW 8.6.1 and TestStand 4.1.1 does anyone know if this issue was address TestStand 4.2?

    It seems that the upgrade can be worth it.

    Simon,

    After investigating the matter further, I found that we had already encountered this bug. It has been fixed in 4.2 TestStand and LabVIEW 2009 I tested your files with 4.2 TestStand, LabVIEW 2009 and everything built successfully without any hiccups on the way.

  • TestStand deployment utility error

    I get the error below in an attempt to build a TestStand deployment.  I'm under TestStand 4.2.1.83 and 9.0.1f3 Version of LabVIEW 2009 Service Pack 1.  Any help would be appreciated, because I can't find the screws mentioned in error.  Thank you!

    From newspapers.
    Based on the analysis
    Transformation of workspace...
    Workspace treated
    Analysis completed
    Building...
    10:15
    Internal error code 6503 treatment live...
    Failed to process screws LabVIEW. Fix all screws broken before the reconstruction. LabVIEW error:
    Exception occurred in LabVIEW: LabVIEW: The VI is not executable. Most likely the VI is broken or one of its subVIs is not found. Select file > open to open the VI and then make sure you are able to run it. Dynamically call Build VI distribution LV 8.6 or higher - TestStand.vi-> TestStand - call Build VI Distribution Unique VI hierarchies LV 8.6 or Above.vi-> Build.vi TestStand - Package VIs.vi-> TestStand--> TestStand - Distribution Wizard GUI.vi-> TestStand - Screen.vi to start the deployment utility
    An installation program was not created due to an error
    The build process is done.
    10:15
    Abandoned

    Hi Shawn,

    I got the same error when you try to create a blank deployment containing only the TestStand engine.  I think the problem with screws with names in double (not my screws, but NEITHER provided screws) that I managed to solve my problem by uninstalling all my software of NOR and then reinsert only my latest software versions 4.2.1 TestStand and LabVIEW 2009 SP1.  My previous installation was versions have been updated over time and that may have led to a screw copy?

    Thanks for your help.

    George

  • HPDM deployment fails with the error code: 14031022

    Hello everyone,

    I ve a strange problem with a new repository of child I ve created two weeks ago. Following situation:

    We have a master and (until now) repository repository a child for two locations. Capture and deployment on each side works fine. Now we're getting a third place, so we need another hpdm gateway and a child repitory to this place.

    I've added and configured as one worked and insert the IP address of the gateway again to a thin client to the new location. When I deploy an image on this client, I get the following error in the console of hpdm:

    2014-12-16 11:02:09 Assign repository: repository child name repository
    2014-12-16 11:02:13 synchronized correctly Completed.
    2014-12-16 11:02:14 task sent to the device management gateway
    2014-12-16 11:02:17 task has been retrieved from the agent.
    2014-12-16 11:02:58 deploy the image ready using the repository: repository child name guard.
    2014-12-16 11:02:58 running common-task failed.
    2014-12-16 11:02:58 Errorcode: 14031022, error details: download the file (s) failed.
    2014-12-16 11:02:58 running common-task failed.
    2014-12-16 11:02:58 Errorcode: 14031022, error details: download the file (s) failed

    Agent of Thin Client Gateway: 4.5.3660.18502

    HPDM bridge officer: 4.5.3660.19.503

    agent update task works.

    I ve configured the shared folder and FTP access. Both are available from thin client. Configuration of the repository the two test passed successfully.

    Repository of child synchronize all the data from the master repository with success.

    Usually, I use FTP in IIS services, but filezilla I ve installed (disabled FTP IIS) for the best connection.

    Connects to the deployment task:

    000027) 16.12.2014 11:02:27 - (not connected) (10.32.2.52) > connected on port 21, sending the welcome message...

    16.12.2014 (000027) 11:02:27 - (not connected) (XX. XX. X.XX) > USER test

    16.12.2014 (000027) 11:02:27 - (not connected) (XX. XX. X.XX) > 331 password required for the test

    16.12.2014 (000027) 11:02:27 - (not connected) (XX. XX. X.XX) > PASS *.

    16.12.2014 (000027) 11:02:27 - test (XX. XX. X.XX) 230 > connected

    16.12.2014 (000027) 11:02:28 - test (XX. XX. X.XX) > FEAT

    16.12.2014 (000027) 11:02:28 - test (XX. XX. X.XX) > QUIT

    16.12.2014 (000027) 11:02:28 - test (XX. XX. Goodbye > 221 X.XX)

    16.12.2014 (000027) 11:02:28 - test (XX. XX. X.XX) > disconnected.

    Next, I get the above error HPDM. The server log HPDM said next.

    2014-12-16 11:11:35 [line 2] WARN Util - revertNumericString fail: k.A.

    2014-12-16 11:11:35 [line 2] WARN Util - revertNumericString fail: k.A.

    Mhh not a lot of information.

    I Don t really get what could be the problem. You have an idea? Do you need more information (newspapers, error message TE) for assistance?

    Concerning

    Martin

    After the coup of controller.conf and the screen of the dialog editor repository that you set, your master repository was not configured this way:

    ReposPath has the value "C:\Inetpub\Ftproot\HPDM" in controller.conf (assume C:\Inetpub\Ftproot is the root directory of the FTP server)

    In the Master repository Editor dialog box:

    Implement FTP path to ftp: / //HPDM - he WS ftp: / /<>/. your screenshot.

    This is the reason that all of your linked FTP task failed with the same error code.

  • TestStand deployment error - error: unable to locate all the screws saved subVIs because it lacks a Subvi

    Hello

    I am a systems and software engineer based in Vancouver. I developed a test system automated using 2013 LabVIEW and TestStand 2013 with custom operator interface.
    I encountered problem 'lack screw' which is kind of weird because I went to analyze the sequence for the TestStand Deployment Utility and TestStand sequence editor > files broadcast tab.
    But when I tried to build the installer and reach the point ' called distribution screw, it always throws an error saying "an error occurred trying to read the error of the screw, possible because the screws are not saved in the latest version of LabVIEW. Do you want to save any changes now? ". I tried both (that is to say Yes and no) for this option, but it has not solved the problem.

    This is part of the original error message displayed in the TestStand deployment utility:
    " ***************************
    Then the treatment live...
    Error: Cannot locate all the subVIs screws saved because a Subvi is missing or the VI is not registered in the last version of LabVIEW.
    The chain of calls to missing screws:
    1 - ATE_AccelerometerTest.vi
    2 - CreateAndMergeErrors.vi (missing)
    3 - LogControl_CheckForErrorSendUpdates.vi (missing)"

    All screw missing come from userlib.

    Actions performed:
    -File of sequence analyzed by using the TestStand Deployment Utility and TestStand sequence editor
    -Checked "search directories" include all the necessary files/dependencies.
    -Mass to compile the directory of the missing screws
    -Added all the necessary files and folders in the workspace file.

    The result is always the same function according to the actions performed.

    Debugging last I did earlier, is that I tried to find the sequence and steps missing screws as shown above (for example ATE_AccelerometerTest.vi)
    and I discovered that the measure appears to be an empty action step. This would be possible even if it has already passed the analysis?

    Other considerations include:

    I'm using sp1 2013 LabVIEW and TestStand 2013. We tried the building three 3 computers and we only managed once to a freshly installed comptuer.

    Hoping to hear from you soon.

    Kind regards

    Michael Panganiban
    Engineering systems and software
    www.Synovus.ca
    [email protected]

    Hi all

    We were able to solve the problem. First of all to note is that the release notes in 2013 TestStand is obsolete and we confirmed engineer OR Austin TestStand 2013 works very well with LabVIEW 2013 SP1.

    Second, we played option deployment TestStand that solved the problem. Attached are the pictures.

    We have activated just the 'delete unused Components VI'. It could be one of the libraries (lvlib) we have included in the compilation, but we've not thought of it again because we have checked that all the screws are working. It could also be something else that I think is very hard to find from information. However, if someone had the same problem, this could be useful.

    Again, we return to using 2013 TestStand and LabVIEW 2013 SP1.

    I appreciate all comments and feedbacks. Otherwise, you can close this request for assistance.

    Thank you.

    Kind regards

    Michael Panganiban

    Engineering systems and software

  • With the help of dynamically called screw in TestStand deployment

    I write code to interface with a & Rohde Schwarz ZNB Network Analyzer.  I use LabVIEW 8.2 and TestStand 3.5.  For reference the ZNB driver is available here: R & S of ZNB Driver.  I use a slightly older version of the driver, some before they needed to LabVIEW 2009.  I am writing all the code on a development machine that has the full version of TestStand/LabVIEW and it works on another machine that has the TestStand deployment license.

    This driver is dynamically linked to some things he needs.  I am able to operate with simple LabVIEW EXEs but not in TestStand deployments.  The following excerpt comes from their documentation, explaining a little about how the driver works and how to use in LabVIEW EXEs.

    3.4.2 How to generate executables or libraries in LabVIEW driver kernel drivers instrument based on attributes is dynamically bound to any VI performed during execution. This can be recognized by the LabVIEW application builder. The LabVIEW application builder follows all the static dependencies and include them in the package distributed at the generation of an executable file.

    To create an executable in LabVIEW, please manually add all the screws in the \PREFIX \_utility\callbacks folder to the LabVIEW project. In the case of project based please add private to your project folder. With this reference manual, the driver core is included in the compilation and the driver core is accessible during execution.

    I can't get this to work in TestStand deployments at all.  I can't even connect to the device since the VI Init has these issues.  I get the same error for all the various attempts that I made.  The same error is that when you add manually the screws for the LabVIEW EXE.

    Error-1073807346

    Property in Rohde & Schwarz Vector Analyzer.lvlib:rsidr_core_session_fgv.vi-> network node

    Rohde & Schwarz Vector Network Analyzer.lvlib:rsidr_core_check_error.vi->

    Rohde & Schwarz Vector Network Analyzer.lvlib:rsidr_core_attribute_write_int.vi->

    Rohde & Schwarz Vector Network Analyzer.lvlib:rsidr_core_attribute.vi:3->

    Rohde & Schwarz Vector Network Analyzer.lvlib:rsvna.vi:2->

    Example 1 setting of the Instrument 24Default .vi:1->

    Rohde & Schwarz Vector Network Analyzer.lvlib-> efault Instrument Setup.vi

    Rohde & Schwarz Vector Network Analyzer.lvlib:Reset.vi->

    Rohde & Schwarz Vector Network Analyzer.lvlib:Initialize.vi->

    Connection of ZNB testing.VI

    VISA: (Hex 0xBFFF000E) the given reference of session or the object is not valid.

    So far, I tried the following, all solutions producing this same error.  I struggled with this and turned off for awhile then maybe there are other solutions attempts I forget.

    (1) it looked like a lot of the report to go to the private folder were finished in SupportVIs.  I manually pasted the rest there, too.

    (2) I added all driver files on my workspace and included in the files with the rest of my deployed screws.

    (3) I added all driver files on my workspace and said pilot TestStand to deploy them to the original location in Program Files.

    Someone at - it ideas?  R & S didn't even know what was TestStand, so that they could not help me.

    I was finally able to solve this problem on mine, the other day.  I brought the Network Analyzer to my office and did a lot of tests in this way.  Eventually, I discovered that I needed to include the folder private pilot deployment, what I was doing in one of previous attempts.  It turns out that you must also maintain the original of this file directory structure when you include it, otherwise dynamic calls are not looking in the right place.  Once it worked on my PC, I got it on the machine test and worked as well.

  • Internal analysis based on the error Code 7

    I am trying to create the Setup program for one of my application and got stuck with deployment error. Build state indicates as follows

    From a newspaper for the deployment.

    Based on the analysis

    Analysis completed

    Error code internal 7 analysis of departure

    Path must be a directory or a LLB.

    Abandoned

    When you click the Distributor tab, he asks "Do you want to analyze the source files?", when I click OK, it says-" < no="" file="" information,="" analyze="" a="" workspace=""> "

    But it does not give the same problem when I uncheck the "of Teststand public directories' in the Source System tab. But I need to include the public directory to create the installer properly. What could be the problem?

    I created Installer a few months back and its job perfectly well. But now I need to review the sequence, that is why the installation program. But not stuck

    TestStand Version 2012

    Fransico,

    I have re installed Teststand 2012 and the issue has been resolved. could not figure that out what was going on. Then uninstalled Teststand 2012.

  • Peer SSL could not negotiate a set of acceptable security parameters. (Error code: ssl_error_handshake_failure_alert) How can this be repaired?

    I got this error message when you try to access a site with which I have a contract:
    The secure connection failed

    An error occurred during a connection to eoffer.gsa.gov.

    Peer SSL could not negotiate a set of acceptable security parameters.

    (Error code: ssl_error_handshake_failure_alert)

       *   The page you are trying to view can not be shown because the authenticity of the received data could not be verified.
    
       *   Please contact the web site owners to inform them of this problem. Alternatively, use the command found in the help menu to report this broken site.
    

    This can only really be corrected by the people who run the site. They have misconfigured web servers. Ask them to test in all modern browsers before deploying in the future.

  • error-18004 in 2016 TestStand

    I am convert 3.1 to 2016 TestStand and LabVIEW 8.6 to 2016.  When I try to run my sequence file, I get the following error when the preload module: LabVIEW: unexpected file type.  Error code:-18004, error to the DLL of the LabVIEW Run-Time engine.  Source: "THOMAS" I can open the LabVIEW vi without any problem and have tried to re - register, which did not help.  If I delete this file in sequence step, the other loading steps and run fine.

    See image attached error.

    Never mind.  I found that it was pointing to code that I had compiled mass.  For some reason, the compilation of all performed mass screws unreadable.  I used a backup of the files and now they don't give me an error.

  • IronPython 0xfffb4e36 script error code

    time of import
    import NIVeriStand
    from NIVeriStand import NIVeriStandException

    WKS = NIVeriStand.Workspace2 ("localhost")
    SYSDEF = r "2013\Projects\Pump\Pump.nivssdf C:\Users\Public\Documents\National Instruments\NI VeriStand"
    print 30 * ' + '.
    WKS. ConnectToSystem (SYSDEF, 1, 60000)
    «"print 30 *» *»
    Time.Sleep (5)

    The screenshot has been attached.

    I could not know what this error code is on the web OR or help file.

    Any idea?

    Hello

    It seems that there is already a Homeless deployed.

    Before calling ConnectToSystem, you could check for a deployed Homeless and disconnect:

    	State = wks. GetSystemState()
    If (["State"]! = 0):
    Print "error! State of the system should not! "
    print ' cancellation of the deployment of the SDF: "+ state ["systemdefinition_file"].
    WKS. DisconnectFromSystem('',1)

  • Why my TestStand deployment installation appear under my Windows will not start menu of my target machine?

    Why my TestStand deployment installation appear under my Windows will not start menu of my target machine?

    I managed to install the deployments of work to the target machines. However, I expected to see the classified facility "My TestStand system" in my Start menu, but it is not. Am I misunderstanding something here?

    Also, if I do another target second deployment to the station as "My TestStand system B", all LabVIEW files in my previous installation for "My system TestStand" disappear from the directory (c:\Program Files\My TestStand system) target.

    I use TestStand Professional 4.2.1 on Windows XP and LabVIEW 2009 development station.

    Thank you Paul,.

    That solved my second problem and inspired me to look deeper for the response to my first problem. The answer lies in the tab 'distributed file","Installer properties' box 'create a program item:

    Wouldn't be nice if it is automatically checked by default for main sequence files? Wouldn't also nice if "Upgrade Code" was regenerated automatically by default whenever we have saved the file *.tsd under another name?

    Thanks again,

    Eugene

  • error code 14 load.

    Has anyone ever seen this error or know what are the causes?

    LabVIEW load 14 error code: could not load type mapping of spatial data.

    I get this error when I run my operator Interface under an account that has a LabVIEW Developer license.

    I understand when I run under the account operator generic unpriveleged.

    The VI in question is vi.lib/measure\matone.llb\Extract Sin

    TestStand is configured to use the adapter Run-Time, so I'm having a hard time understanding why an account works and there is no.

    That sounds like the issue discussed here:Why do I get error-17006 during the loading of a VI from a library of project packed in TestStand?

    This article also explains the error code 14.

  • error code 17301

    When I try to compare it to similar .seq file using diff sequence I get an error:

    Index out of range

    Error code:-17301

    Is it because the sequence files are not quite similar? The sequences are similar, but there are different menus and the sequence of calls. Does anyone know why I get this error?

    What version of TestStand do you use? You can try in a newer version of TestStand to differentiate files if you are not currently using the latest version?

    -Doug

  • Setup of LV 2011 Build-30 error code

    With the help of LabVIEW 2011 SP1 winth Windows 7.  Made changes to a program, and tried to create a new executable and Setup.  Executable worked well.  Had the following error when I tried to create an installer:

    CDK_Build_Invoke.VI.ProxyCaller > CDK_Build_Invoke.vi > CDK_Engine_Main.vi > IB_MSI.lvclass:Build.vi > IB_MSI.lvclass:Engine_InitializeDistribution.vi > NI_MDF.lvlib:MDFConfig_SetDistributionLanguage.vi

    Loading information of product deployment
     
    **************
    Error: Bad line of command or argument of function call. (Error code - 30)
    **************
    Error details:
    Error to the MDF API function: _MDFConfig_SetDistributionLanguage
    The MDF has no support for language LANGID 9 distribution.
    Final report of the error
    **************

    Any help is appreciated.

    This thread suggests the uninstallation and reinstallation of LabVIEW, and ensuring that you have all updates.

    http://forums.NI.com/T5/LabVIEW/can-t-build-any-installer/TD-p/2120890

  • Executable cannot find the custom error code file

    I'm building a LabVIEW 2013 application on a Windows 7 computer and deploying it to a Windows XP computer. My application has a custom error code file, stored in -- errors.txt, but my executable on the Windows XP machine can't find the custom error file and returns only the string of appeal for all errors that occur.

    When you use is not an installer, I tried to copy the error code at all locations listed here: http://digital.ni.com/public.nsf/allkb/6077DBEDA4F9FEE3862571F600449501 but the application still does not load the custom errors. I have the box checked to "Error Codes customized Include" in the construction specifications.

    When an executable of construction and the development of Windows 7 to XP, where do I put the custom error code file? It is found in Program Files (x 86), but find not because it's XP?

    It's been a few months that I posted this question and I do not know if someone cares about this track, but the solution I found was to put the custom in error code file \National Instruments\Shared\Errors\English\

    There are other places that the runtime will look for the custom error codes (I tried all the ones listed above), if the same error codes exist in 2 places the error popup will appear two error messages. Error default 1, it looks like:

    LabVIEW: An input parameter is not valid. For example if the input is a path, the path can contain a character not allowed by the operating system such as? or @.
    =========================
    NOR-488: Command requires GPIB controller charge controller.

    So if you have a custom error code file and it is available in 2 places that LabVIEW RTE check error codes, you will get the same message before and after the =.

    List the error as "still included" file when building the executable or by checking the box to include files in error did not tour, obviously. Unless you create a Setup program to distribute the application, the error code file must be moved manually. Shared\Errors file works best for me because it's a place that makes sense.

    Also, don't worry - it doesn't me taken 5 months to understand this point, I do not update all my loyal followers (ha) with a solution.

Maybe you are looking for