error code 43 usb not recognized when connecting usb (sd card) with asus X55C laptop.

Similar Questions

• USB device not recognized when connected to Toshiba Port Replicator II

  I recently bought the Replicator above, loaded the software, restarted my computer and only then connected the device according to the instructions.

  I get the error message "unrecognized usb device".
  When I go in my gear and check for driver for this device 'unknown' told me that no drivers have been shipped for her

  So my Replicator does not.
  I deleted the software and reloaded with the same result

  I have a laptop Tecra A8 running Windows XP Service Pack 2
  Any help or suggestion would be appreciated

  As much I know PortReplicator II only is not supported for Tecra A8. According to the sustained specification is Port Replicator III + only.

  If you try to use the option not supported, it is not easy to give any help.

• USB device not recognized when connected to the computer

  original title: USB port problems

  When I plug a usb device, I get a message not recognized usb device (one of the usb devices attached to this computer has malfunctioned and windows does not recognize)

  Hello

  ·         Since when are you facing this problem? Were you able to use this USB device on the system before?

  ·         Remember to make changes to the system?

  ·         It happens with all USB devices that try you to plugin for the system?

  I suggest running the fix which is present in the article below and check if the problem persists.

  Advanced troubleshooting tips for General USB for Windows XP problems

  http://support.Microsoft.com/kb/310575

  Also, I suggest you return the item mentioned below.

  A computer that is running Windows XP cannot detect a USB, an Apple iPod flash drive or an external hard disk drive

  http://support.Microsoft.com/kb/925196

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.

• USB device not recognized when connecting to printer

  Hello Microsoft,

  Hear I have problem in my PC. I connect to my new printer (RIOCH SP 100), but in my Winodws7, they show me that your usb device is not recognized. I try to use the resolution of problems. but it was a failure of dem, so now what is the way to solve my query.

  Hello Dhruv,

  Thanks for posting your question on the Microsoft community.

  We need more information about the issue so that we can help you better.

  What is the complete model of your printer RICOH SP 100 number?

  Thank you for details on the issue.

  This problem may occur because of settings and corrupt device drivers.

  I would suggest trying the following methods and check if it helps.

  Method 1:
  Run the hardware and devices Troubleshooter and check.
  Reference:
  Open the hardware and devices Troubleshooter
  http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter

  It checks the common issues of interest and ensures that a new device or hardware connected to your computer has been installed correctly.

  Please also run the printer Troubleshooter and check.
  Reference:
  Open the printer Troubleshooter
  http://Windows.Microsoft.com/en-us/Windows7/open-the-printer-Troubleshooter

  He made sure that a printer is connected to your computer, and it checks for common issues such as whether the printer has enough paper and toner to complete printing your document.

  If this does not help, use method 2.

  Method 2:
  Controllers USB reinstall and check the issue. Please follow these steps:

  a. press Windows + R keys together, type devmgmt.msc in the run window and press ENTER.

  (b) in Device Manager, expand 'USB Bus controllers'.

  c. right-click any device under "Controllers of Bus USB" and click Uninstall.

  d. repeat the same steps for other devices.

  e. Once completed, restart the computer.

  I hope this information helps.

  Please let us know if you need more help.

  Thank you

• When you try to activate Windows I get an error: Code 45123 could not establish a connection with the activation server.

  the error number is 45123 and said "we could not establish a connection with the activation server." Please give me an answer to this error and try to solve it! If you want I can send you my product key to activate it, but I think it's better on email not here because there are a lot of... the pirates who have access to this site! provide me with an email address and I'll send you my product key and try to activate it and then give me the id I need to enter the activation window! Thank you!

  I solved this problem! Thanks for the help!

• Devices not recognized when connected to itunes from a PC. Recently upgraded to windows 10 and appears there is no driver

  I'm sure that this request has jumped several times. I've recently upgraded hardware and software being windows 10. All devices being Ipads, Ipods and Iphones are not recognized in iTunes once connected to your PC. The PC is to recognize that a device has been plugged in with the usual beeps. I've seen drivers and it seems that usb iTunes etc is not listed. How this can be fixed. Thank you inadvance for advice

  Hello, Aubin Grove,.

  Thank you for using communities Support from Apple!

  I understand that your iOS devices are not recognized by iTunes when you plug it into your computer. There may be two different causes for this type of situation, but we have some great troubleshooting to help you resolve this situation.

  To begin the process of diagnosis, I would suggest reading over and working through the information mentioned in the following article.

  iPhone, iPad, or iPod not recognized in iTunes for Windows - Apple Support

  See you soon!

• error code 0 x 643 returned when Windows Update failed in the XP Home laptop system

  Could not install Win Update (KB951847) x 86 called MS .NET 3.5 service pack 1 + update .NET framework 3.5 .NET 2.0 to 3.5 worm family.  I need help to fix my laptop Win XP Home to accept this update, but also cases of simultaneous failure of (KB969615) windows update error code 0 x 4397 - MS Office 2003

  You will have to reinstall applications

  1. how to fix corruption problems MSI software update registration
  http://support.Microsoft.com/kb/971187

  2. If this does not work-

  Versions of the .NET framework must be installed in this order, .net Framework 3.5, .net Framework 1.1, .NET Framework 1.1 SP1

  Follows (in reference to the removal for the framework and associated information tool)

  When you try to install an update for .NET Framework 1.0, 1.1, 2.0, 3.0 or 3.5, you may receive Windows Update '0 x 643' error code or error code Windows install "1603".
  http://support.Microsoft.com/kb/923100

  When installing updates using Windows update or Microsoft Update you may receive error 80070643 0 x or 0 x 643
  http://support.Microsoft.com/kb/976982

  TaurArian [MVP] 2005-2010 - Update Services

• iPod 4th generation not recognized when connected to a USB port.

  Original title: question

  When I connect my ipod 4th generation in the usb port a message out saying that it recognizes not it. I tried everything and it still refuses to recognize my ipod. What should I do?

  Hello

  Check with iPod Support and Forums for more information if necessary.

  -IPod support
  http://www.Apple.com/support/iPod/

  iTunes and iPod Support
  http://www.Apple.com/support/

  Each iPod - iPod help & Technical Support (part 3)
  http://www.EveryiPod.com/iPod-help/index.html

  ---------------------------------------------------------------------

  For most MP3 players that can and will be able to be synced to WMP - iPod syncs not natively for Windows.

  Set the MP3 MTP Mode for WMP sync - mode MSC to treat the MP3 as a reader.
  (Now its set to MSC)<-- this="" is="" for="" mp3="" in="" general="" and="" ipod="" will="" not="" usually="">

  Your MP3 player should have 2 settings - MSC which should allow the player to be used as an external symbol
  drive and PSG that is the parameter to use to sync with WMP. Remove the MP3 and charge it the
  computer. Change the MP3 in MTP mode - it power off and plug it in.

  ======================================

  There is a plugin to let WMP sync music to an iPod:
  http://thewelltemperedcomputer.com/SW/WMP/sync.htm.------

  WinAmp supports iPod
  http://www.Winamp.com/

  How to use Winamp to manage your iPod
  http://www.SimpleHelp.NET/2007/07/07/how-to-use-Winamp-to-manage-your-iPod/

  WinAmp - Forums
  http://forums.Winamp.com/

  6 ways to synchronize your iPod to computer without iTunes
  http://www.MakeUseOf.com/tag/6-ways-sync-iPod-computer-iTunes/

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Mobile gamepad XBOX 360 not recognized when connected to a Windows 7 64 bit Home Premium computer USB ports

  Very well - so a few days ago (Saturday ~ 2) (25. 2012) I connected to my XBOX 360 (Wired) controller on my Toshiba Satellite L655 computer laptop with Windows 7 ~ Home Premium 64-Bit. To my surprise, a Notification bubble popped up from the taskbar, saying that the "unrecognized USB device. It has malfunctioned. "

  Naturally, I took, waited a few seconds, and then reconnect the USB key. The same message has popped up. Now, I was angry. Repeatedly, I took and reconnected it all a few seconds until that FINALLY the 4 green lights around the button Guide everything illuminated and then back except the one on the upper left, which was the way it should have been.
  I went to the control panel and clicked on the 360 controller to see if he had any input. Nope.
  I pulled out once more, has waited a while and plugged in. No, lucky. The same thing happened again. The Notification bubble came, all 4 green lights on and then all four of them died. I don't know what happened.
  When I plugged the controller to the laptop the FIRST FULL TIME, he installed all necessary drivers in less than a minute and I was on my way. Every time after that, I have taken the controller into the USB Port and began to play. Now all the time, that is to say that it cannot recognize the controller?
  I've tried everything, even a system restore. Nothing did. I've uninstalled and reinstalled the drivers for a few minutes, there was an entry of the controller, then he went just blank.
  I need this controller in order to play my racing games, seeing the keyboard control just aren't the best. I don't know what the problem is, but I wish I had a solution A.S.A.P. Please, Microsoft, please. Help me!
                                                                                                                          
  
  
  
  

  I had the same problem, cannot find a solution that worked everywhere, including Microsoft support forums.

  About to give up, I remembered the old cure NDA, shaped, "why not?"  I've tried everything else. "So I've disconnected everything on the gamepad, blew in every connection and reconnected everything, by ensuring that the connections were tight.

  It has worked perfectly since then.

• printer is not found when connected to the router with the ethernet cable

  My c6280 used to print wireless (not a wireless printer) because I had hooked to the router.  Now, it won't work - I'm on Mac OSX Lion.  I tried to delete the printer and reinstall.

  Hello

  Please make sure to remove the software completely, because there is no plans for Lion.

  While the printer is connected to your network,

  Go into System Preferences > print & scan and click on the sign more.

  Select your printer and the driver will download automatically the Apple software update.

  For more information, you can follow the document below:

  http://support.HP.com/us-en/document/c02911238

  If the update fails to install Apple servers, download and install the package of the latest version of the HP to Spple printer software:

  http://support.Apple.com/downloads/DL907/en_US/HewlettPackardPrinterDrivers2.7.2.dmg

  After completing the installation, add your printer as explained previously.

• We get the popup "USB device not recognized", when nothing is connected.

  Original title: pop up message

  I connected the USB cord to transfer information from your old phone to new phone via Itunes.  Since that time that I keep getting a pop up message that says: device not recognized USB, the defective device, windows does not recognize.  Nothing is plugged in, but message appears every few seconds.  How can I get him to stop?

  Hello

  It seems that you are getting the popup "USB device not recognized", when nothing is connected.

  What is the brand and model of your computer?

  I suggest to uninstall the USB controllers and check if you get the context menu.

  
  

  Method 1: Remove and reinstall all USB controllers

  
  

  a. clickStart, type devmgmt.msc in the start search box and press ENTER.

  b. expandBus USB controllers.

  c. right-click on each device under theBus USB controllers node and then click Uninstall to remove them one at a time.

  d. restart the computer, and windows will install the rear USB drivers.

  If reinstalling USB host controllers fails to resolve the issue, go to method 2.

  Method 2: See the procedure suggested by johnkelly46 responded on October 26, 2009, from this link.

  If you have additional problems, please reply to this post and we will be happy to help you further.

• When I use the Client for NFS provided by Windows 7, I'm unable to connect. The "mount \\ip address\share Z:" command fails with the error code "the path not found network".

  Identification of customer's Windows 7 NFS UID GID information

  I am trying to connect to the Windows 7 Client NFS on a server running on a computer (VxWorks) NFS.  I am able to properly connect Client NFS software by a 3rd party on the NFS server.  However, when I use the Client for NFS provided by Windows 7, I am unable to connect.  The \\ip address\share Z: mount"command fails with the error code"the path not found network ".  I can't do a ping of the computer running the NFS server.

  The NFS Client operating system: Windows 7 Ultimate, 64-bit

  Data captured by Wireshark

  MOUNT V1 EXPORT call 3rd party client
  Identification information Flavor: AUTH_UNIX (1)
  Length: 32
  Stamp: 0xc7065970

  Machine name: PC
  UID: 1000
  GID: 1000

  MOUNT V1 EXPORT appeal of the NFS client
  Identification information Flavor: AUTH_NULL (0)
  Length: 0

  It seems that the credentials of NFS Client are not correct.  How can I change the flavor of AUTH_UNIX and the UID and GID to 1000?

  Hello VDAEMP,

  As Eddie and Sudarshan has said, the Microsoft Answers community focuses on issues and problems related to the consumer environment. Please join the public IT pro TechNet forums below:
  TechNet - Windows Server
   
  Thank you

• Keyboard Dell Bluetooth is not recognized when energy savings and will not wake my computer. My usb mouse not recognized or the other.

  My Dell Bluetooth keyboard is not recognized when energy savings and will not wake my computer. My usb mouse not recognized or the other.  I use keyboard now, but it seems not be installed yet when I check my keyboard or bluetooth devices. Keyboard does not work after so I'll try to figure out what to do before moving into the power saving mode. Help, please. I did all the updates from microsoft, and there is no update for my bluetooth device, I checked.

  Hello

  1. have you made changes on the computer before this problem?
  2. What is the model of the keyboard?
  3. are you an error message or error code?
  4. which version of the Windows operating system is installed on your computer?

  I suggest you to consult the following Microsoft article and check if it helps.

  On troubleshooting in Windows 7 power management: http://support.microsoft.com/kb/980869

  Troubleshoot keyboard: http://windows.microsoft.com/en-US/windows-vista/Troubleshoot-keyboard-problems

  Keyboard and Microsoft mouse refer:

  Troubleshoot the incidents of the response to the mouse or wireless keyboard: http://support.microsoft.com/kb/838398

  Reference:

  Troubleshooting external Dell Wireless or Bluetooth keyboards and mice: http://support.Dell.com/support/topics/global.aspx/support/KCS/document?docid=277550#Issue0_1

• automatic password is not recognized when I change the password, but in vain

  automatic password is not recognized when I connect in outlook express. He saw the day without obvious reason. I tried to change the password, but to no avail.    A ny comments or solutions?  Jong

  Hi Jong,

  ·         What is the full error message?

  I suggest you to consult the article in the Microsoft Knowledge Base and check if it helps.

  Save the password setting will no longer exist in Outlook or Outlook Express

  http://support.Microsoft.com/kb/290684

  I hope this helps.

• The Apple Magic Keyboard can operate without bluetooth when connected to an iPad with the lightning to the USB camera adapter?

  The Apple Magic Keyboard can operate without bluetooth when connected to an iPad with the lightning to the USB camera adapter?

  I love the Apple Magic Keyboard to be very light (I want it with me everywhere). I also like that I can choose the layout of the keyboard I want (Canadian multilingual), which is not available on any keyboard for any brand, with the exception of Apple iPad (and I did a ton of research). I have problems with the old model of keyboard Apple Wireless because of the Bluetooth connection: I often have trouble connecting. I want a reliable keyboard. I don't like having to plug the keyboard on the iPad, and I think that a wired keyboard can more reliable and safer than a wireless keyboard. And a wired keyboard never had battery problems.

  I read that the Apple Magic Keyboard can work wired with a Mac without bluetooth. And I read that some USB keyboards work with lightning to the USB camera adapter. There are several keyboards with a cable (Belkin or Logitech) lightning, but none with the available Canadian multilingual.

  So, if I buy a magical keyboard Apple and a Flash to the USB adapter of the camera, according to my needs, I'll be satisfied or I'm going to be disappointed?

  A better solution would be to have a male-male cable lightning between the keyboard and the iPad, but I don't find any of these products anywhere.

  Thank you.

  It will not work. And where did you read that the keyboard works wired with a Mac?