Error - EPPkt.sys and c:\windows\system32\drivers\afw.sys not found and fix crashes in Windows XP Pro computer.
Original title: during repair XP Pro from the disk installation, everything crashes.
I am writing this plea on my desktop, pc Win 7 it. The pc is older and elsewhere in the House.
Due to the white/white space in Add/Remove Programs, after checking the extent of possible for viruses, corruption Reg, etc., the advice of consensus was to reinstall the Windows, using the disc (this XP Pro was on the HARD drive when I got the pc - new to 2009 - and I did the back-up recommended/controlled , and that's what I was doing Rcounter Set up, around 1700 BST.
Everything seemed to go OK, but black screen of Windows is now the small hourglass circulating and 'Please wait '. The HARD drive is flickering, but it's been more than 3 hours!
My second pc was rotten, and I had to reinstall or repair XP Home [disk] a few times. It is only 35 GB, compared to more than 100 on the pc in question - but I've never met before delay.
Installation messages were as follows:
EPPkt.sys and c:\windows\system32\drivers\afw.sys not found. I checked this point, and it should not have caused any problems. It has also sought a labeled disc 'Machine Virtual Network Services', which no doubt, since I did not, was never necessary.
I'll leave it on - but...
Help, please!
Well, I had to bow to the inevitable. Please accept this response as a ' I've been there - it could happen to you. "
I spoke to BT [they provide my broadband] and the helpful guy asked me to look at the installation and reinstall in a different place. It's OK, but [, BUT] some of the drivers have been zapped in eternity. PCI, sounds, videos. The guy thought BT that these had been modified or replaced since the beginning, whereas they were not available. The XP Prof is on the pc when I got it, but I assumed that the pilots were on the backup disk, I did. No, they were not. And how to go online to search for them if we could not put in place the ethernet connection?
So, I bought Win - 7 it 32-bit full ed. [be too afraid to try an upgrade].
It could have been a response in the migration of these from other drivers, but I guess it was time to go.
As I can't afford to buy new COREL, MS Word, etc, I have installed free VMWare player as a host for my older progs in a virtual environment.
Another thing came out of this: although what remained of XP has been saved by 7 as WINDOWS.old, I am very happy that I had a HDD eternal with ntfs to preserve my files and installable 3rd party progs.
I hope this might help someone - thanks for the info.
Tags: Windows
Similar Questions
-
Original title: file "c:\windows\system32\drivers\afw.sys" agnitum firewall driver, how to find it.
I downloaded a trial version of Bullguard internet security and while downloading stopped at one point and ask for the file above. I tried a nd produce no result. Any ideas please. Thanks, pete
C:\windows\system32\drivers\afw.sys with description Agnitum Firewall NDIS Driver is a driver file of Agnitum Ltd. belonging to Outpost Firewall product.
The file is digitally signed Agnitum Ltd. - VeriSign Time Stamping Services signatory - G2
We do not recommend remove digitally signed files from Agnitum Ltd.
Chk this link
http://www.OutpostFirewall.com/Forum/showthread.php?22526-missing-Afw-sys
Replace the file from another computer and check.
try to download it from this link
-
Error messages occur now - seem to appear now, after I did a Defrag. If I try to open AOL, it brings me to a display list who wants to choose from a list of programs. For AOL, I click on AOL. I didn't used to have to select from a list of display. Then I tried to open an Astrology program and it took me to the same list, which of course is not. Now, I get the same error as follows: C:Windows/system32/rundll32.exe - Application not found - OK
Here's a Plan:
Goto, start system restore restore Menu\All Programs\Accessories\System Tools\System
Now select the oldest Restore Point and restore your computer, but first make sure that you have an external drive.
After that C:\Windows\System32\Rundll32.exe copy the external drive and the disc is ejected
Open the system restore and undo restore
After the undo operation is copy the Rundll32.exe in the road to C:\Windows\System32
and the problem solved
Note: the rundll32.exe should be missed recently and you should have an old Restore Point which contains a file Rundll32.exe Intact
-
UPHClean not install on XPsp3, error message: uphcleanhlp.sys not found
I tried to install UPHClean - Setup.msi and she runs up until the last bit of the installation. He then told me that she can't finish and the installation will stop. The error message is: "uphcleanhlp.sys" not found. But I found myself in the folder "C:\windows\system32\drivers". I am running Windows XP Sp3. Please let me know if there is a solution to this.
Try to install this latest version: User Profile Hive Cleanup Service
-
Original title: rundll.exe error
I checked the previous messages and can't seem to find a solution to this problem. Recently I ran 3 different scans, i.e. sbybot, avast and Malawarebytes virus. After that I ran these anti-virus programs and remove viruses, I was not able to open any more virus scanners. Every time I tried, would open a window saying "Choose the program you want to use to open this file." If I try to download a new virus scanner, it says the same thing.
When I try to open the Control Panel, add or remove programs, a window appears saying "C:Windows\system32\rundll32.exe Application not found. I checked this file on my c: drive\system 32 and see the rundll.exe file. I also copy and pasted the file rundll.exe my CD of Windows XP in c: Windows\System32
Everything else seems to work fine on my computer, and I get no message on the rundll.exe file when the computer starts up first.
Any help would be popular!
Hello
You rename regedit.exe regedit.com?
Remove from my computer-> tools-> file-> option-> view tickmark for "Hide extension for known file types"-> ok-online local disk now C:\WINDOWS\
Regedit.exe search
Make a right-click Rename regedit.com
From start-> Run Type & -> regedit.com-> ok.
and follow the registry path IE: HKEY_LOCAL_MACHINE\Software\Classes\Exefile\Shell\Open\Command
I hope this helps.
-
C:\Windows\system32\CNUpdater.exe was not found.
When I start the PC, it says there's an update available, but I get this error "C:\Windows\system32\CNUpdater.exe was not found." when I try to do the update. Can you help me with this? Thank you!
But this isn't an update of Windows. See http://social.answers.microsoft.com/Forums/en-US/w7repair/thread/f1c4b380-679d-466e-908d-bfa9684c6133 ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft
-
my Windows xp pro computer worked fine but after five days, when I stat my computer I could show only the bios information on the screen then the screen freezes, then I started ahead of time the computer starts at mode, but once again he the disply frozen. I couldn't start my computer. I have a lot of data in my hard drive. What can I do to start computer or recover my data?
First run Memtest86 +:
It runs from a floppy disk or CD and should eliminate or confirm if your one or more of your memory
sticks are bad or the values of the SPD in the BIOS are correct.
Let it run for as long as you can: 2,4,6,8 or several hours (at least 3 full passes), if no errors, then your RAM is OK.
http://www.memtest.org/
Memtest86 + Guide/How To (use the.) ISO to create a bootable CD)
http://www.overclockers.com/forums/showthread.php?t=409152Test your player - create a Bootable CD:
Ranging from 5 to 20% (depending on the manufacturing) new hard disks are defective.
Test your drive with the car manufacture utility.
If you have a new hard drive Seagate the very next thing would be to download Seagate Seatools
(bootable CD) and check bad sectors:
http://www.Seagate.com/WW/v/index.jsp?locale=en-us&name=SeaTools&vgnextoid=720bd20cacdec010VgnVCM100000dd04090aRCRDFor Western Digital readers to download the .iso from WdDiag file: http://support.wdc.com/product/download.asp?groupid=611&sid=30&lang=en
Samsung Estool: http://www.samsung.com/global/business/hdd/support/utilities/ES_Tool.html
Samsung Disk Manager software: http://www.samsung.com/Products/HardDiskDrive/utilities/shdiag.htm
Hitachi Drive Fitness Test Software: http://www.hgst.com/hdd/support/download.htm#DFT
Diagnostic tool available for use by customers who feel their Toshiba brand Fujitsu hard drive:
http://SDD.Toshiba.com/main.aspx?path=ServicesandSupport/WarrantySupport/SoftwareUtilities
Notice of suport Fujitsu disk utility: http://www.fujitsu.com/us/services/computing/storage/hdd/
Toshiba CD bootable: (BACK Diagnostic Tool version 7.0 for IDE/ATA/SATA hard disks)
http://SDD.Toshiba.com/main.aspx?path=ServicesSupport/FujitsuDrivesUSandCanada/SoftwareUtilities#diagnosticJ W Stuart: http://www.pagestart.com
-
0x8007045D error code when you install Windows 7 Pro 64-bit
I get an error 0x8007045D code when installing Windows 7 Pro 64 bit on the same same MSI 970 Gaming (AMD SB950 Chipset 970 +) motherboard, even OEM Win Pro SP1 7 X 64 dvd, the installation on an EVO of 840 Samsung 250 GB SSD.
16 GB of Ram (4 GB X 4 stix. Ran this OS on this forum for a year, trying to do (was) a clean install. I am puzzled, never had a problem like this.
I was the installation of the operating system, and you're right, when he was on the 2nd works. He remained at 0% for a while then I get this error message "Windows cannot install required files. Make sure all files required for installation are available, and restart the installation. 0x8007045D error code.
Someone at - he already had this?
Any help would be appreciated.
Thank you
Try to reduce the amount of RAM installed on a unique key and try again.
If you have several hard drives attached, disconnect all except the disk target hard.
If you have compatible hardware and your computer still stops responding, disable any unnecessary material. Remove (USB) universal serial bus devices. Remove or disable network cards, sound cards and cards of the series; and then restart the installation.
-
C:\Windows\system32\regsvr32.exe is not found
When I try to load the softwear I get this message - C:\windows\system32\regsvr32.exe is not found
Hey,.
Read this article:
http://support.Microsoft.com/kb/q249873 -
"Error while interacting with the scanner: the selected scanner was not found." Called brother and my MFC 7360N works very well with other programs to scan - only problem with Adobe Acrobat Pro 11.
Please provide the exact point of the software & OS installed on your system. Also check if it is there any update available for the software after going through "help > check updates.
Follow this thread to reset the Acrobat preferences:- How to reset preference settings in format Acrobat.
You can check after connecting this scanner locally to the system if asked its connected on network & then look for the same thing.
Please refer to this article:- of the troubleshooting tips for scanning questions when using Acrobat
If the problem persists ask please check with another user account.
Kind regards
Christian
-
RTKVAC. SYS not found?
VISTA HOME PREMIUM
32 BIT
SERVICE PACK 1
My pc got fuck with all these updates. Do a clean re-install of VISTA, but have no sound, can't download REALTEK AC97 for love nor Fatima, all attempts at just says RTKVAC. SYS not found.
What this means and how do you solve. I know about pc s, so if anyone can help, explain in simple terms please.
Don't tell me to re - install, I did only yesterday. None of this is my fault but MICROSOFTS. We shouldn't have to do all this, the updates should not mess up your computer.
Who creates the sfcdetails.txt and you will have to go to it and read it but confirms your 2nd round
no error found.Still think your best bet is to remove BullGuard.
Good luck.
Rob - bicycle - Mark Twain said it is good. -
Error code 0 x 80070035 that the network path was not found.
OT: error code 0 x 80070035
My wife and I have 3 computers all running Win 7 64 bit. Two jobs and the third is a laptop. My desktop or laptop computer I can access any folder of each machine. However, when I try to click on my wife under 'Network' computer I get the message "Windows cannot access\\wife_desktop." When I click 'See details' it displays "error code 0 x 80070035. The network path was not found. "I'm running out of things to try. I tried to use my desktop computer and notebook to help me check the installation on my wife's computer. I have updated owner and security settings in both car and system, as well as temporarily disable the firewall. Any suggestions would be greatly appreciated.Hello
Method 1: Run the network troubleshooter and check out what he has to say.
See the links below:
http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7
http://Windows.Microsoft.com/en-us/Windows7/open-networking-troubleshooters
http://Windows.Microsoft.com/en-us/Windows7/use-Network-Troubleshooter-event-logs-to-solve-network-problemsMake sure network discovery is enabled on the laptop computer, by default the State network discovery is disabled. If network discovery is off, please take the following steps to turn on.
(a) click Start.
(b) click on Control Panel.
(c) click on network and sharing Center.
(d) click on the arrow to drop down next to the network discovery.
(e) click on the option, turn on network discovery.
(f) click on apply.
http://Windows.Microsoft.com/en-us/Windows7/enable-or-disable-network-discoveryMethod 2: The question can be caused also by your security program such an antivirus or a firewall of Windows /Defender that can have conflicting parameters as to not not to perform certain tasks. I suggest you temporary disable antivirus and firewall and check the result again. You must activate new security that you was disabled programs.
http://Windows.Microsoft.com/en-us/Windows7/turn-Windows-Firewall-on-or-off
http://Windows.Microsoft.com/en-us/Windows7/disable-antivirus-softwareSee the following link: http://social.technet.microsoft.com/Forums/nb-NO/w7itpronetworking/thread/028a3d13-f571-49e0-abe7-1ca61fb92082
-
I got a message when I reboot my pc«svhost error: this application has failed to start because xul.dll not found.» Reinstalling the application may fix this problem.I need someone to help solve this problem.
Let's see...
I downloaded this zip file to see what was in it. The version of the file in this download link xul.dll is approximately 2 years and version 1.9.0.14
The version of the xul.dll of Firefox on my system (trying to keep up-to-date and all) is aged two weeks and version 5.0.
I think I want to reinstall Firefox, but this isn't the Firefox forum.
-
error message: "WINDOWS\system32\rundll.exe is not found."
WINDOWS\system32\rundll.exe cannot be found please check the root etc... etc... I've tried everything here. How do I just uninstall WINDOWS and then reinstall it? I tried ALL of the suggestions I found here. It is not in my Cache file, either this one's empty! Please help me.
Click Start > run > type or paste c:\windows\servicepackfiles\i386 > Ok. Now, look in the folder for the file i386. If you cannot find the download from HERE and place it in c:\windows\system32.
-
New components is a new computer.
Inserted the XP Pro CD in the drive but get the error "file not found \i386\ntkrnlmp.exe. The error code is 7. »
Rebooted comp 5 times with the same problem after BIOS.Hi Milkshake83,
Thanks for posting. Proceed as follows for this error.
Method 1: Restore the default settings of the BIOS WARNING: this procedure may involve changing the semiconductor (CMOS) settings of the computer's complementary metal oxide and by changing the BIOS of the computer. Incorrect changes to the BIOS of your computer can result in serious problems. Change the CMOS settings of the computer at your own risk.
To resolve this issue, restore the BIOS of the computer to its default settings. For more information about the correct settings of the BIOS of the computer and how to check and change these settings, see the computer documentation or contact the manufacturer of the computer.
In addition, to confirm that the computer's BIOS is current, contact the computer manufacturer to inquire about the last update of the BIOS available for the computer.
Method 2: Remove the faulty RAM to resolve this issue, remove the memory modules installed in the computer.
NOTE: you must leave enough RAM for the computer to start and run Windows.
For more information on the amount of RAM that is required to run Windows, click on the number below to view the article in the Microsoft Knowledge Base:
304297 configuration (http://support.microsoft.com/kb/304297/) System requirements for Microsoft Windows 2000 operating systemsIf the error message described in the "Symptoms" section of this article appears again after removing the memory module, remove a different memory module. This procedure may ask you to restart your computer several times to identify the specific memory module that is not working properly.
For more information about how to add and remove RAM to the computer, contact the manufacturer of your computer or see the documentation that came with your computer.
http://support.Microsoft.com/kb/318729
I hope this helps!
Shawn - Support Engineer - MCP, MCDST
Microsoft Answers Support Engineer
Visit our Microsoft answers feedback Forum and let us know what you think
Maybe you are looking for
-
Toshiba control buttons don't work no-Portege R200
Hello Hi I formatted my Toshiba Portege R200 reinstalled Windows and drivers without the recovery disk. The problem is that after you have everything installed, I work the shortcut keys (Toshiba controls enabled in the control panel to assign functio
-
What is the best? Windows 7 or vista
Which of the two above gives fewer complications? These days most people are turning to Windows 7. is it useful?
-
nothing yet
-
BlackBerry Smartphones just bought a Blackberry "BOLD" in Thailand to be used in the Philippines
Hi all I recently bought a new 'fat' in Thailand. It cost me about 600 U.S. Dollars and this is unlocked. I used my SIM from the Philippines who wandered in time and was able to send a text message, so I guess it works OK. I have a few questions,
-
Appworld blackBerry Smartphone problem
I tried to download Patter Lock Lite for my wife BB Storm and its deadlock on the downloading part departure. Its been like that for about 2 weeks now and I also think that its causing his phone drag or run slowly. I already uninstalled Appworld twic