Error in the printer - Deskjet 6840

Similar Questions

• When I try to print anything in Firefox, email or the Internet, I get a message that says: error in the printer and nothing prints. Tried the stuff even printing from the Internet

  When I try to print anything in Firefox, email or the Internet, I get a message that says: error in the printer and nothing prints. Tried to print things even to Internet Explorer, it works fine.

  Hello bdoolen, please try to reset firefox and see if that can solve the problem...

• Want 4500: Connection error! The printer could not connect to the server

  Connection error! The printer could not connect to the server!

  Cannot set up eprint or update the driver. Ever been on the forums and do not understand what to do!

  I am successfully connected to my router and can print from my pc and my ipad with airprint.

  PC "will not find"the printer either for purposes of updating

  What I need to change the DNS. If so, I don't know what it is or how to do it!

  I went to the ip address but was unable to click on "wireless (802.11)", as recommended by a last response forum, as the next low 'status '.

  Can anyone help?

  Very frustrated customer :-(

  Hi @roopuk,

  Thanks for getting back to me.

  Sometimes the manual DNS 8.8.8.8 / 8.8.4.4 won't work in some configurations of network users.  Try the same steps as described above, but this time use the following parameters:

  Manual preferred DNS Server: 209.244.0.3
  Auxiliary manual DNS server: 209.244.0.4

  If you encounter the error, as before, we take our proverbial gloves off to try a more intensive troubleshooting.

  What is happening, it is that your router allows your printer connection that to enable wireless, but not a secondary connection to Web services.  In order to get these devices to 'shake hands' a second time, you may need to enable DMZ mode on your network through the router's built-in Web server.  HP does usually not this configuration for its customers as errors can cause serious network problems, but I can certainly post the info you need on your router or the ISP of the staff support company so that they could help you directly.

  Here is the information that you need for your provider service to open ports on your router/modem...

  -Multicast must be enabled
  -Hello enabled for AirPrint (relevant for iOS and Mac OS users)
  -Mac filtering should be disabled
  -Also, make sure that your router's firmware to date if
  necessary
  - The dmz on the router mode and turn it on to the printers IP address: _

  Ports to open are: Eprint and Apps

  Incoming Ports.

  UDP
  80
  443
  ------------------
  Outbound ports

  TCP
  5222
  5223
  -------------------
  Once they are open, you should have no problems connecting to services web eprint on your device.

  I would like to know how it works for you.

  Kind regards

• C4780 - error in the printing system

  C4780 worked without incident for months until recently - now I find randomly in status 'offline '.  Today has been visited by "error in the printing system.  Any ideas?  I already deleted the printer and the software which then does a re - install using the downloaded software from the HP site (can't locate the original install CD).

  OK, I'll assume that this printer is connected wireless to your router.  I would like to know if it's USB to your PC.

  First of all, don't use WEP.  It is not safe and can cause connection problems.  Use WPA with a password of 13 + character that you create yourself!  Much easier and safer.

  From the front of the printer: [Scan] Setup > network > wireless network Test.  It will be radio of the printer self-test.

  When the printer is offline, run this utility.  It will tell you what is happening.

• When you print it out paper HP PSC 1507 just repeat the error in the print job

  Hi im on MAx OS X 10.6.4 and I got it all in one HP PSC 1507 printer... I don't know why but I have intralled all the drivers n etc. but it keeps just coming with error in the print job just stay

  Any help would be appreciated

  Thanks George

  Good question.  Although it is listed as being supported under Snow Leopard, there is not another print and scan all drivers.

  We will restore the print system and just use the built-in support for your printer:

  -Sys Prefs, Print & Fax
  -Right (control) click inside the box that lists your printers and select Reset Printing System.
  WARNING - This will remove ALL your printers!
  -Select the sign + to add again. Search for the printer, select it, and wait until the button 'Add' becomes available. Until it clicks.

• Error in the printer for 16-bit application that runs in Windows7 32 error "caused a floating point exception in hpcui121.dll to 0x5b39caea.

  Original title: Error in the printer for 16-bit application that is running in Windows7 32

  I have a 16-bit application. I'm running Windows 7 32. All of a sudden, I can't print my application. I have two messages: "caused a floating point exception in hpcui121.dll in 0x5b39caea" and "caused an access violation in WOW32. DLL to 0x6dc50421. Any help to solve the problem would be greatly appreciated.

  Hello

  Have you tried the methods suggested in my previous post dated August 29?

  Response to help you further.

• 'Use the cartridges SETUP' error on the printer, need help!

  I bought the printer last year in the months of August and after 6 months of use, it started having problems printing wireless. I always had to use USB to print from my laptop so I was recommended by people in this forum to reset my printer to the factory.

  I have reset several times and nothing worked, so I was advised to do so by using the Cancel button and the middle button that reset the printer. Now the problem is it says "Cartridges use SETUP" and my printer is out of warranty, it expired last month. I'm really confused about what to do. I am a student and I still have the print job and I can't afford a new printer. Calling support has no idea what to do and email support does not because of my warranty as you exhale.

  My printer is a HP Deskjet printer Wireless 3070. Product number is CQ191B.

  I really need help has begun the new year of college and I have a lot of missions to print.

  Hi ExPLOiT786

  Dragon-fur asked me to chime in with this. I will send you a private message on this in order to proceed.

  Ciara

• DeskJet 3520 e-all-in-one: How do I install the printer deskjet 3520e ink cartridge

  I have a hp laptop touchscreen and I do not remember how to replace the ink cartridges. Please help! l

  Here, the video shows how to install a printer Deskjet 3520e ink cartridge.

• Error in the printer "document in the ADF.

  Original title: Canon injet 310 series

  All of a sudden, my printer shows this error when I try to print "document in the ADF.  When I press ok to delete it, the same message appears.  What is an ADF?  How can I fix?  Help, please.  Thank you.

  Linda, in addition to "stir" around with the paper-feeder(open the drawer, take out the paper, put it back in well aligned) and wiggleing everywhere elsewhere where it is possible, I'm ideas! Sorry! Don't forget: it's obviously a kind of jam: just so push, shake and 'free' the printer...

• HP8620: Error in the printer

  I went to my HP8620 yesterday to find a printer error duisplayed on the screen.  He said "Please stop printer, then press.  All the lights were flashing.  I turned the printer, then on and the printer has been its start-up phase.  Almost immediately, the screen went black, then blue, and finally the printer error appeared again on a white background.

  I repeated this procedure several times them turn off the printer and unplug.  I disconnected and then reconnected the USB connection to my PC.  Whenever the printer error again.  While the screen is momentarily blue there is a code B840E9E2 displayed number.

  Sometimes my PC goes to Flash a message if the device connected to the USB port is not recognized.

  Hello

  Please try the steps below...

  1. While the printer turned on, unplug the power cord from the back of the printer.
  2. Unplug the USB cable from the back of the printer, as appropriate.
  3. Turn off the wireless router.
  4. Wait 30 seconds.
  5. Connect the power cord to the printer.
  6. Check if an error appears.
  7. When the printer is ready, make a copy. Check to see if the error is.
  8. Turn on the wireless router.
  9. Check to see if the error is.

• Photosmart P6350 will not print, but the computer analysis. Have 'Error' on the print monitor

  The two HP1300 Photosmart inkjet machines and displays the same error message and print, however the Photosmart P6350 scans and copies. Scan indicates the all-in-one is online, but I send a print command and the print monitor responds with 'Error' and no other information. I'm puzzled. I tried all the remedies support hp; same result. iMac OS 10.6.8 recognizes two printers but simply shows them "idle".

  Download and install this: http://support.apple.com/kb/DL907

  Reset the printing system:

  -Go to System Preferences > print & Scan
  -Right (or control) click in the rectangle listing your printers and select Reset Printing System.
  WARNING - This will remove ALL your printers!
  -Select the sign more to add a printer. Select the default tab on the top of the window. Search for the printer, select it, and wait until the button 'Add' becomes available. Until it clicks.

• How can I fix the following error message: The Print Shop 3.0 (or other program) has encountered a problem and needs to close.

  Print shop does not open. He was relocated several times.  Every attempt to open the following the error messge program appears: The Print Shop 3.0 has encountered a problem and needs to close.

  Hello

  Check the event log information when you try to start printing 3.

  Procedure to view and manage event logs in Event Viewer in Windows XP

  http://support.Microsoft.com/kb/308427

  Resolution:

  I suggest that you start the computer in a clean boot with printing 3.0 active state.

  See the link below to perform the clean boot in Windows XP.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Note:

  How to configure Windows to use a Normal startup state

  After you have used the boot is a way to solve your problem, you can follow these steps to configure Windows XP to start normally.

  1. Click Startand then click run.
  2. Type msconfig and click OK.
     The System Configuration utility dialog box appears.
  3. Click the general tab, click Normal Startup - load all device drivers and services, and then click OK.
  4. When you are prompted, click restart to restart the computer.

• How can I fix the error message "the print spooler service does not work."?

  All printer drivers that I had loaded do not work or have disappeared.  After you download the printer drivers, I got the error message: "operation could not be performed.  The print spooler service is not running. "I have Windows XP.  I need to print now!

  To start the print spooler service, click Start > all programs > Accessories > run. In the run box type in services.msc. In the Windows Services window right-click on print spooler and select open. You will then see the options "Start automatically", and then on the button 'Start Service'. Click on those and then click apply then OK. Who should start the print spooler service, however, if you get an error message, see the link below for more information.

  http://social.technet.Microsoft.com/forums/en/itprovistaprinting/thread/391f3c57-5d2b-4E88-ADC6-190429a7fdbe

• How to make the printer deskjet 3940 compatible with Windows 7 Home Basic, 32-bit?

  I have the HP Deskjet 3940 printer. I recently bought a Lenovo (C320, 57-302429) desktop computer that has Windows 7 home basic, 32-bit operating system. The said printer does not work with the computer above. Please guide how to make this printer compatible with the operating system above.

  1. click on the Start button, select Control Panel and double-click devices and printers.

  2. click on Add a printer.

  3. Select Add a local printer.

  4. Select an existing Local USBx port, click Next.

  5. click on the Windows Update button.

  6. once the update is complete, locate the 3940 driver.

  7. click on Next,Next,Next,Next,Finish

• HP P3015: ERROR ON THE PRINTER CAN'T USE. There 49.4C02 OF the ERROR AND DO WE ALLOW to ENTER IN THE MENU SETTINGS/AUTO

  OUR LASERJET P3015/CE527A CAME UP WITH THE ERROR 49.C02.  HE WILL NOT ENTER

  MENU/SETTINGS FOR AUTOMATIC RECOVERY.  IT COMES UP WITH THE ERROR AS SOON AS IT IS TURNED

  TURN IT BACK ON AND CANNOT ACCESS THE SETTING.

  This could be a few things-

  First thing I would do, is try to turn the machine off and then remove the network cable from the machine.  Once extracted, try to turn the machine on and see if the error goes away. If so, there are probably a print job corrupted in the queue. Which you can remove by going in Printers and devices - the print driver for the HP - go to 'see what's printing' - right click and delete the tasks in there. If the drivers are not on a server or on your computer, you may wander and find the computer on which the print job is