Error loading on my satellite 4080CDT

Similar Questions

• "Error loading operating sytem!" on Satellite A55

  I'm going to reformat Toshiba Satellite A55 Series for Windows XP. It is said that he cannot reformat the C drive and HDD may be damaged and to quit smoking just press F3, and then I press F3.
  But it said "error loading operation of the sytem!

  What should I do to fix this? Anyone who can help me what about this one?

  Thank you!

  Hello

  If the hard disk is damaged there is a single Exchange of hard drive solution. For this laptop model hard drive isn't cheap and I think that it is better and easier to solve this problem.

• Re: Satellite A300 - error loading operating system

  Hi, I have a computer laptop satellite a300 and when I boot the system I get an error message "Error loading operating system" - if some kind posters can help me on this issue, it would be much appreciated.

  Thank you

  Don

  The BIOS recognize the drive? Check in the BIOS.

  You can start in safe mode?
  If you go into the advanced boot menu, select Repair my computer, and then select Toshiba Recovery option. This procedure reinstalls the operating system.

  This feature is only available with a preinstallation of Windows Vista. If you have Windows XP, you must use the CD.

• Satellite L300D: error loading operating system - Ubuntu Linux

  The easiest way, you could any body help me with "error loading operating system"!
  Completely screwed?

  have you checked whether your CD s severe correctly?
  What distribution you install?

• Satellite L300-20W - "error loading operating system"

  When I turn on my laptop, the Toshiba screen charge then it will a blank black screen with a white underscore flashing in the upper left.

  A few seconds later this message appears in the upper left corner "error loading operating system" I watched v online on how to solve this problem, but all that happens is complicated jargon.
  Anyone know how I can remedy this in simple terms?
  See you soon

  Hello

  I can't say with certainty what may be the problem but maybe HDD (hard drive) is a troublemaker.

  Start your laptop and press F2 to enter the BIOS settings. Check if the HARD drive is recognized and registered properly on the page. Load the settings by default using F10, then restart your laptop.

  The same thing happens again?

• Cannot connect - error loading the database...

  Hello

  Since last night find it me impossible to log in on my Skype.

  He puts me "error loading the database. Skype." It is possible that another instance of Skype to use it.

  I have reinstalled Skype, restart my pc, close all programs that could use it.

  My husband get a leverage son skpe without pb so it comes well d a pb with my nickname... going to Word of the change back I. Despite all this, I still have the same message that appears! 1

  did anyone have the same pb? and how he made it?

  Please pour your help!

  Rrbonjour

  so I did well the manip: Task Manager, process shutdown Skype.

  then relaunch the application, but it gives me the same result...

  I made a new system more earlier but it's restore gives me the same result...

  I asked a third person open my account on another pc and ca works... so it just my pc, not a hacking, (already it reassures me!)

  My spouse does so well to open Skype with his nickname but I still nothing.

  Application rattachee a Skype name can she used Lun?

• Error loading C;\users\Toshiba\appData\Local\SMBDP.dll

  Can someone help me?
  Once I start, I get a message that says: error loading C;\users\Toshiba\appData\Local\SMBDP.dll, then the module is not found.
  I tried everything but can't get rid of it,

  I asked for help online, but he told me to buy a tune-up utilities, but I already have untilities tune-up and have run through completely but it always does'nt work.

  Help, please.

  Hello

  TO be honest, this file is unknown to me. I searched using Google, but I couldn't find anything :(

  You can try a system restore to an earlier point or what have you done since you got this error message?

• displ1.dll error loading of worksheet

  Just before a work critical time that we started getting an error loading Dasylab 10.0.3 spreadsheets.  It was one of those things "windows has encountered an error and needs to close."  Looking at the details it is said that the problem was with displ1.dll.

  He is our saved records unusable because they could no longer be loaded into Dasylab without the occurrence of the accident.

  I finally got around the problem of removal of displ1.dll in the folder \windows\program files\dasylab 10 then run Dasylab.

  This allowed me to open our existing worksheets, but with a red cross on modules as required displ1.dll - including the table of yt and the list.  If I deleted these modules, I could at least save and reuse the leaves of calculation (but without our list and graphical views).

  My quick workaround solution had to then restore displ1.dll and reload Dasylab.  I could now open my old worksheets - because they had none of the modules requiring a displ1.dll in them.  Before my acquisition of data, I could then manually add the table yt and the list shows and then begin the work.  No problem as long as I did not save the worksheet with a list or table of yt - if I do so then I would get the same error as previously not described.  So with a short time (a few hours) I came with a 75% on solution work that required minimum re - work whenever we wanted to use the spreadsheet.

  Has anyone encountered this problem before and why is this happeneing?

  In my initial confusion, I uninstalled Dasylab then re-installed as 10.0.1 to see what would happen.  Still received the error of displ1.dll.  Then I applied SP2 to resume installation to 10.0.3 and it still doesn't work.  I note that there is a new version of displ1.dll in SP2.

  We used 10 Dasylab for several years with the same hardware DAQ (IOtech Wavebooks) for several years now without any problem - how is this problem appeared seemingly from nowhere?

  Andy Phillips

  OK... my research says that the bug you described is fixed in V10.0.3.

  Then, go towww.mccdaq.com and ask for support. Please indicate in the text that CJ has asked you to do, so that they will assign it to me.

  I have the following of you:

  -copy of the worksheet

  -the list of the DAQ hardware used by the worksheet

  -l' help-> report of DASYLab

  I need to check that you did not find a new unique bug...

• Error loading lvdaq.dll

  Hello forum of Discussion of LabView.

  I am currently using LabView 2009. My Research Director has tried to open the files inherited from Labview 7.1 on the more modern version, without success. After doing a little research, I found that I had to download traditional DAQ in order to get the latest version of LabView to open the older file. First, I downloaded the DAQ for 7.4.1 and installed with setup.exe, after which I tried to open the program. I got the «error loading lvdaq.dll...» Error in initialization failed". I then downloaded 7.4.4, thinking that maybe it would be a better version. Same mistake. I'm now downloading version 7.1 (a previous DAQ inherited), thinking that maybe the version numbers should equal to the origin of the old Legacy DAQ file I have to run it. I hope that it will work (and if that's the case I'll just delete my post), however if it isn't, I'll update my post and I hope to help to know what to do.

  Thank you in advance for any help.

  
  

• Error loading operating system - version of WHS disks

  I have an old MSI k9 & AMD x 2 4600 + Im running WHS v1 (but I don't think it's a problem WHS).

  Moments ago, the server crashed (bad discs).  First, the configuration of this system has always had a problem starting from cd/dvd player and always been specific as to which SATA connection is used to start a disk of. In the past, I had to build a system disk / boot on another pc then it switch.

  I did now, twice. The reconstruction on the main PC went without a hitch. The new boot disks joyfully on the main PC. I transferred the drive (s) in the server box, and I get the error "error loading operating system".

  I tried to connect to all of the SATA ports in turn, with different cables, including one that was on the other PC. I removed all other players to avoid confusion.  Software diagnostic WD gives readers a certificate of good health.  BIOS identifies the present disc, and it is configured to boot from it as first choice.

  The BIOS is the same as it was when buying - but this version has 2 previous builds to get

  I have to believe the following

  1. the discs are good, and the construction is lilkely ok.

  2. the cables are also correct.

  So the fault (s) are:

  1. the SATA controller has ceased to be particular that disc it starts from, allow no boot at all, so a fault of SATA controller

  2. There is something in the full version, which is connected to the main computer - maybe I should stop the construction earlier and swap discs then?

  3. a BIOS setting is in the way and I can't.

  4. something else is at fault

  Its the thing that bothers me and so I hope that someone can suggest what I could try next. I Apologise if this isn't the right place for this, I am new to this sort of thing. Best regards, Michael

  Hi Michael,

  It is suggested that you post your question related to Windows Home Server on the link here. They are a dedicated team who assists questions about Windows Home Server. Message here:

  https://social.Microsoft.com/forums/en-us/home?category=WindowsHomeServer

• Error loading C:\Users\gelwix\AppData\local\temp\

  How can I get rid of this message when I start?  Error loading C:\Users\gelwix\AppData\local\temp\

  Hello

  1. What is the version of the operating system installed on your computer?

  2 have you made changes on the computer before this problem?

  3. What is the exact full error message?

  Then follow the mentioned methods:

  Method 1:

  Use a tool like autoruns to locate the reference and delete it.

  Autoruns:http://technet.microsoft.com/en-us/sysinternals/bb963902.aspx

  Method 2:

  If you use windows XP follow this:

  Put the computer in a clean boot state to see if there is a software conflict as the clean boot helps eliminate software conflicts.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Note: After completing the steps in the clean boot troubleshooting, follow the section How to configure Windows to use a Normal startup state of the link to return the computer to a Normal startupmode.

   

  If you are using Windows Vista or Windows 7 follow this:

  Perform the clean boot and check.

   

  To help resolve the error message, you can start Windows Vista or Windows 7 by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  
  Please note:  After troubleshooting, be sure to start your computer in normal mode by following step 7.

   

   

  I hope that the above information is useful!

• How to erase or correct an error loading RUNDLL that keeps Poppin ' up C:\ProgramFiles\ParetoLogic UUS2\USS.dll the specified module could not be found... error?

  How to erase or correct an error loading RUNDLL that keeps Poppin ' up C:\ProgramFiles\ParetoLogic UUS2\USS.dll the specified module could not be found... error?

  Hello

  Here is some information on this problem.

  The information contained in the link suggest you delete a scheduled entry, if it exists:

  http://www.utilitysoftwarereviews.com/how-to-remove-ParetoLogic-uusdll-error-message/

  You can also use this program (FREE Autoruns) to find:

  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902

  See you soon.

• Error loading C:\windows\iambcex.dll error codes

  Original title: error codes
  On my pc, I have not been able to obtain the nywhere.  When I open windows I get two error messages:
  Error loading C:\windows\iambcex.dll
  Error loading C:\windows\iyigexindoduse.dll

  A google search produces no results. This suggests that the relics of an incompletely removed malware or malicious software.

  It is always sensible in this situation to achieve a malware check

  Start the computer in safe mode with network and download and install Malwarebytes (free version for individuals only), updated definitions and run in safe mode. Disable other security software while you do the analyses.
  http://www.precisesecurity.com/how-to/HT-smodewnet.htm
  http://www.Malwarebytes.org/products/malwarebytes_free
  Download and run SuperAntiSpyware (Free Edition)
  http://www.SUPERAntiSpyware.com/download.html

  To identify what loads when you start using Autoruns (freeware from Microsoft).
  http://www.Microsoft.com/technet/sysinternals/ProcessesAndThreads/Autoruns.mspx

  With Autoruns, you can deselect an item which disables startup, or you can click with the right button on an item, then remove it. If you clear the check box that you can check back for re - activate the element. It is an approach much safer than editing the registry and better than using msconfig.
  Another useful feature of the program is that you can click with the right button on an item and select search online to get information about the selected item.

• Whenever I reboot I get the following message: error loading C:\windows\claprv.dll

  Whenever I reboot I get the following message:

  Error loading C:\windows\claprv.dll

  the specified module could not be found

  What does that mean?  The only thing that I found online, it is that it can be associated with some malware?

  Any ideas?

  Hello, Rojo97,

  You have something to do with skiing?  This site uses claprv.htm.  You will get a 404 error page not found but the site is active.

  http://www.Sloski.SI/resources/files/PDF/alpsko-smucanje/04-05/FIS/alp_claprv.htm

  Have you added new software to your system recently?

  Download Microsoft malicious software removal tool run a complete analysis

  http://www.Microsoft.com/download/en/details.aspx?displaylang=en&id=16

• "Error loading operating system" after windows update

  I have an ASUS EeePc netbook model: 1005PEB. Last night before going to bed, I stopped the netbook and it has begun to install and configure windows was last updated. I left on the office do its thing and went to bed. This morning, I got the netbook and it went out of the car and it turned on while I was about to leave the House (before ask you, no I ' was not flying). He started installing all the updates that it had installed the night before. It has gotten to the point where it installed the last element and hung up there. I leave a this screen for 45 minutes and nothing has changed. I went against my better judgment and off the netbook. When I went immediately to turn it back on all I get is "error loading operating system". I tried to use F8 to try to start it in safe mode and I can always access the BIOS. How do I get this service still? I don't have really any data here, I'm too preoccupied. Thanks for any help anyone can offer.

  Hi argyle_83,

  Were you able to boot into safe mode?

  This problem can occur if your computer's BIOS does not correctly manage or support the capacity of the hard disk on which you install Windows 7. You can try the steps below to resolve this issue.

  Method 1: Obtain the latest BIOS updates

  WARNING: This article contains steps that may involve changing your BIOS or parameters of semiconductor (CMOS) to complementary metal oxide, or that may require you to make physical changes to your computer hardware. Incorrect changes to the BIOS of your computer may cause serious problems. Microsoft cannot guarantee that problems resulting from changes to your BIOS can be solved.

  Your first step to solve the problem of the error loading operating system should be updated to your computer BIOS.

  Contact the computer manufacturer to find out how to obtain and install the latest available for the computer BIOS update.

  Find information of BIOS on your Netbook from this link.
   
  http://support.ASUS.com/download/download.aspx

  Here are answers to some common questions on the basis of input/output system (BIOS).

  BIOS: Frequently asked questions

  Method 2: Run the Startup Repair

   

  Startup Repair is a Windows Recovery tool that can fix certain problems, such as system files missing or damaged that may prevent Windows from starting.

  Refer to this article for more details.

  What are the system recovery options in Windows 7?

  http://Windows.Microsoft.com/en-us/Windows7/what-are-the-system-recovery-options-in-Windows-7

  Kind regards

  Shinmila H - Microsoft Support

  Visit our Microsoft answers feedback Forum and let us know what you think.