Error message 'Please select the access point or wireless router to set up' when you set up a network

Similar Questions

• Receiving the message "Wireless association failed because Windows did not receive response from the access point or wireless router" _

  My laptop was working fine yesterday, but when I started it today I get the message "Wireless association failed because Windows did not receive response from the access point or wireless router.

  I can see my network and I can connect to the internet using my desktop pc, but just to make complicated I can't even connect to the network when I plug the ethernet cable into my laptop.

  I think it might be a driver problem, but I have no idea how to solve this problem without access to the internet on my laptop.

  I'm running Vista and my wireless router is an Atheros AR5009 809.11a/g/n

  I need step by step instructions on this Yes please treat me like a fool!

  Thank you

  Laptop would not work at home thus concluded that it was a BT Broadband do not issue my driver (despite BT telling me the opposite last night)

  After the call to a fantastic Lady in BT it's all fixed and thanks to Jack I now know a lot more on connecting wireless to my laptop!

• Wireless connection failed because windows did not receive response from the access point or wireless router

  Monday Nite I downloaded a driver site HTC syn my Android Hero phone. After extracting and installing the driver in the zip file, I tried to sync with my phone which was hook up my laptop. It did not work. Interrupt the synchronization process and I tried to check my email from outlook. Found it cannot send and receive mail. Open my browser and found that it disconnected. And so, using the LAN cable, fortunately, it worked. So I wonder what is happening to my function wireless on my laptop?

  Can someone tell me what I need to do? Thank you very much.

  Hello

  Search for updated drivers and reinstall if no later by using the procedure below.

  Control Panel - network - write down of the brand and the model of the Wifi - double click top - tab of the driver - write
  version - click the driver update (cannot do something that MS is far behind the pilots of certification). Then
  Right click on the Wifi device and UNINSTALL - Reboot - it will refresh the driver stack.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  Download - SAVE - go where you put it - right click – RUN AS ADMIN.

  You can download several at once however restart after the installation of each of them.

  After watching the system manufacturer, you can check the manufacturer of the device an even newer version. (The
  manufacturer of system become your backup policies).

  I would also turn off auto update for the drivers. If the updates Windows suggests a just HIDE as they
  are almost always old, and you can search drivers manually as needed.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• Launch of Lightroom 6 is not. error: "can't find the access point of the procedure _crtCreateSymbolicLinkW in the MSVCR110.dll dynamic link library.

  It says: "cannot find the access point of the procedure _crtCreateSymbolicLinkW in the MSVCR110.dll dynamic link library. What can I do? I have already uninstall and then reinstall the software...

  It is indeed a microsoft problem, check here:error "did not find the entry point _crtCreateSymbolicLinkW - Microsoft Community .

• I have a compaq presario cq57 notebook pc and my wireless is not solving the problems of work said that the access point and wireless network card works I need help to fix this please

  the internet works only with the ethernet cable and not wireless. I have service with comcast.

  Hi, Antonia.
  Thanks for posting your question on the Forums of community of Microsoft.
   
  1. do you get an error message?
  2. don't you make changes to the computer before the show?
   
  Here are some ways you can follow to resolve the problem:
   
  Method 1:
  Check out the link and follow the steps in the article:
  Troubleshooting your wireless network and Internet access (Windows 7)
  http://h10025.www1.HP.com/ewfrf/wc/document?cc=us&LC=en&DLC=en&docName=c02543015#n55

   

  Method 2:

  Reference:

  How can I troubleshoot network card?

  http://Windows.Microsoft.com/en-us/Windows7/fix-network-adapter-problems

   

  Hope this solves the problem

• "Error message: out of memory". Save or close any files or applications"when you try to print the Works spreadsheet

  Original title: receive in Microsoft Works Spreadsheet click on print, I receive this message. "Out of memory. Save or close any files or applications "Whats wrong?"

  Same as above

  Hi dennyfer21,

  1. This only occur when you print the Works spreadsheet?

  You can read the following article and try the steps and check if it helps to solve the problem.

  "Not enough memory" error message when you print to the works

  http://support.Microsoft.com/kb/841220#appliesTo

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Locking down system and now get error 'Could not load the profile user and loading of temporary user account' when you try to open a session

  When my computer is on suddenly power went and my system also closed that crashed without logging my user account. now, I started my computer and I tried to open a session in my account (having only one user account) but he goes to the temporary login account, it displays "could not load the profile user and loading of temporary user account if you make changes to this user account it will be erased when you connect after." What can I do? How can I solve it? I use windows xp.

  Original title: Temp user login

  Hi indhru,

  1. Did you the latest changes on the computer?
  2. You have security software installed on the computer?

  Try the step after the connection to the temporary account below.

  1. Click on the Start menu.
  2. Type Regedit in the Run dialog box, and then press enter
  3. Access
     HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\ProfileList
  4. There is 1 line for each profile. Especially if a profile is bad there are 3 things worth visiting:
  • Make sure that the name of the key are not ends in ".bad".
  • Make sure the RefCount value is 0
  • Ensure that the status value is 0

• Access point or wireless router

  I'm looking for thoughts, opinions, facts, etc. on the best way to set up my home network. The House is relatively new and I cat5 wiring in most of the rooms with home runs to a structured in the basement wiring box. Have nearly 16 shots here. I have currently a linksys BEFSR81 router/switch, hubs, one couple and a Comcast cable modem there. On the second floor, is a wireless linksys WAP610N access, connected on one of the tracks cat5 in the basement. For customers, I have four wired pc which is a music server, couple Blu ray drives, three iPhones, iPad and an iTouch. The House is on two floors with a finished basement, ~ 5 000 total FT2 and construction wood. Right now, my wireless is uneven with him sometimes abandon no explainable reason (Wired is very well in those moments) and connect devices new wireless takes several minutes where it shows a signal but will not connect to Internet. I have read many bad reviews on the WAP610 and wonder if it's my problem. My son says I should get a wireless router with a separate switch to manage 16 wired ports and empty the WAP and BEFSR81. I have a great aversion to turn a unit of wireless streaming in a basement being the lowest part of the House. I move the cable modem and a new wireless router upstairs on the first floor and then run a return line to the basement for the 16 switch ports? Or just get a better/other WAP?

  How would implement you? Sorry for the lengthy post.

  If you do not have problems with the WAP610N you can of course use. You could start to buy only one additional access or wireless router and see how it plays along.

  Concerning the choice of the E-series router, it depends on what you need. The WAP610N is a router dual-band which has a radio 2.4 GHz and 5 GHz radio. If you want to keep the simultaneous dual band radios the cheapest option would be the E2500. There only the ethernet 10/100 ports.

  If you don't want the dual band, the E1x00 could do. But remember, those who only works on the 2.4 GHz band and depending on where you live, you can already see a lot of other people with 2.4 GHz band routers, so you will have a lot of interference on the 2.4 GHz band...

  Of course, dual-band single-band vs depends also if you still have the 5 GHz band devices, or plan to get one.

• You try to run any .exe gets the pop-up message "Please select the program to run rundll32.exe.

  Check on a friends computer; It can run internet explore unless she added as an administrator. you try to run any .exe gets this pop asking what program to run this title?  It could be an association of .exe that is messed up, or is it probably some strange virus?  I tried to install IE9, I was able to download but are unable to run.

  Start here (especially if you are not familiar with the UAC in Vista & Win7)-online http://windows.microsoft.com/en-US/windows-vista/User-Account-Control-Overview

• I get the error message "cannot open the access control editor. The system cannot find the file specified. "

  I'm trying to move some files around, but when I try to give the necessary permission, nothing happens, the file stays where it was.

  Hello

  ·         Did you make any changes before the show?

  ·         Do you have a password for your user account?

  ·         How many accounts user are there in your computer?

  I suggest you follow the troubleshooting steps below to help solve the problem.

  Method 1:

  Turn off UAC and check if that helps.

  To change UAC settings follow the link below:

  Enable or disable the User Account Control

  Method2:

  You can also create a new user account and check it, if the problem is resolved:

  Create a user account

  If the problem persists no new user account, then I would say that correct you the user account damaged by following the link below:

  Difficulty of a corrupted user profile

• "Receive error message" due to an unidentified problem, Windows cannot display WIndows firewall settings "when you turn the Windows Firewall

  Original title: how to enable the Windows Firewall?

  How can I activate the Windows Firewall?

  When I click on it in the Control Panel, I get a message that says "Due to an unidentified problem, Windows cannot display WIndows firewall settings".

  I use Microsoft Essentials antivirus.

  Hi Tom,

  A firewall is software or hardware that checks information coming from the Internet or a network. The firewall blocks the information or allows information to pass to your computer. If the information is blocked or passed through depends on your firewall settings. A firewall can prevent malicious software (such as worms) to access your computer through a network or the Internet. A firewall can also help stop your computer from malware sent to other computers. Windows XP, Windows XP SP2 and Windows XP SP3 includes firewall software.

  Perform the steps from the link below and see if it helps.

  How can I turn on or turn off the firewall in Windows XP Service Pack 2 or later versions?

  Hope this information helps.

• When I try to run Age Of Empires with the CD in, I get a message "Please insert the right CD-ROM, select OK and restart the application.

  Former title: Trouble running games CD, post installation under Vista. That is to say 2 AoE, Warrior kings.

  I have vista on my laptop, I installed games like shogun and medieval total war and they both work perfectly, I tried to put it on the age empires and warrior kings: battles who are also on a cd format, I installed the last but they usually run after that. Although the instialltion is over, I get asked if I wanted to leave the program to run as administrator. : s

  DVD/CD drive recognize there is a disc, but does not work automatically. I can't install the program normally when I run the setup.exe for the game. When I try to run the program with the CD in, I get a message "Please insert the right CD-ROM, select OK and restart the application.

  I tried to run them in compatibility mode, using all variants. and also I tried soome of advice from the help article about the disk drivers. game discs are clean and one striped.

  Why can I install the program and access the drive to use the files it contains, but then not use the disk?

  Hello
   
  
  This problem may occur if one of the following conditions is true:
  a. you do not use the game disc to start the program.
  b. the CD player is not compatible with the program.
  c. using a copy of the program CD.
  d. you are not connected to the computer as an administrator.
  e. the programs interfere with the start of the game which is running but is invisible to you.
  f. the CD-ROM drive uses out-of-date drivers.
   
   
  I would ask you to try the methods listed in the article below:
  Error message or the game stops responding on the "Loading" screen when you start a Microsoft game: "insert the right CD.
  http://support.Microsoft.com/kb/228985/en-us
  
  I hope this helps.

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• When I select Help and support icon, I get an error message indicating that the feature could not start.

  help and support does not work

  When I select Help and support icon, I get an error message indicating that the feature could not start.

  I use a Vista 32 bits on a HP computer operating system model number m8300f.

  In addition, I bought a copy of Win 7, but who could not load freezing during installation.

  Hello

  Try to run the command in the elevated command prompt, follow the steps below, it could help us solve the problem.

  1. open the start menu, click programs principally made, select accessories.
  2. right click on command prompt, and then click "run as administrator ".
  3. type the following commands in the DOS prompt window and press ENTER at the end
  of each line:

  REGSVR32 MSXML3. DLL/U
  REGSVR32 MSXML3. DLL
  REGSVR32 MSXML6. DLL/U
  REGSVR32 MSXML6. DLL

  (At the elevated command prompt command should not give us any error).

  Restart the computer and try to access help and Support.

  For the problem of installation of windows 7.

  We would like to get more information about you to help solve your problem. You better, please answer the following questions.

  1. How did you start the installation process?

  2. you perform a new installation or an upgrade?

  3. what type of drive you are using for installation?

  4. at what stage of the installation has it stopped?

  5. have you received an error message?

  First of all, I would say that you disconnect external devices connected to the computer except the keyboard and mouse.

  If you have performed an upgrade suggests to restart the computer and you will be prompted for a roll back option.

  Once you're on the office suggests to run Upgrade Advisor and check what needs to be done before you start the upgrade.

  Before you begin the upgrade process to ensure that your computer meets the condition of equipment to install Windows 7 and check on the website of manufacturer computer if the computer is good to run windows 7 or not.

  Installing and reinstalling Windows

  http://Windows.Microsoft.com/en-us/Windows7/installing-and-reinstalling-Windows

• Error message "To display the contents of the Flash technology in this PDF file, please install this version of Flash Player that supports Adobe Reader and Acrobat".

  I converted MS-Outlook 2010 e-mail folder (and emails) into a PDF portfolio. When I have Adobe Reader X R-clicked, selected, I got and error message "To display the contents of the Flash technology in this PDF file, please install this version of Flash Player that supports Adobe Reader and Acrobat". I get the same msg when I try to open it with Acrobat. He worked the week last in Adobe Reader. I have the latest version of Flash Player installed. The portfolio opens when I click on < more >, but the Index is missing and I can't get to the first email. PC platform. Anyone else having this problem? If so, how to fix?

  You are running Internet Explorer by chance? If so, the Flash Player you have is NOT in need of Adobe Reader and Acrobat. If there is a link in the message, use that, rather than assuming that you already have Flash Player. If this does not work, let us know.

• I get a dll error message that says: "the application or DLL C:\WINDOWS\system32\kizinone.dll is not a valid Windows image. Please check this against your installation diskette.

  I get a dll error message that says: "the application or DLL C:\WINDOWS\system32\kizinone.dll is not a valid Windows image.  Please check this against your installation diskette.

  I went to the system registry to find the file it refers and is not a he.  I ran a norton registry cleanup and a virus scan.  I did find something online that made reference to this dll file.  The message appears at any time that I start a new program.  How to fix this, or find the virus that is the cause.

  A Google search for "[insert the name of the file]" grown up nothing. When you get no hits for a filename on Google, chances are high that it is a malicious program file. You did not when you get the message. If it's only at startup, either you have uninstalled the malware program or your antivirus/antispyware program did. In all cases, a reference has been left in the boot file. You can remove the reference by managing your startup. If you get the message during regular time on the computer and not not only at startup, your computer is still infected.

  Norton will do the job of cleaning and registry cleaners are garbage who at best will not do anything and the worst risk damage to your Windows installation.

  First of all, make sure that the computer is really free of virus/malware through these systematically - General malware removal steps http://www.elephantboycomputers.com/page2.html#Removing_Malware . Then, if the computer is really clean and you still receive the message, manage your Startup to remove the reference to the malware:

  Start > run > msconfig [Enter]

  This will open the System Configuration utility. Look under the Startup tab and find the likely culprit. Uncheck the box next to its name, apply and OK out. You don't need to restart immediately, but next time you do, you will get a dialog box saying that you have used the utility. Just check the box that says in effect, "don't mind to this subject again".

  How to troubleshoot by using the Msconfig in Windows XP utility - http://support.microsoft.com/?id=310560

  The free Autoruns program is very useful for managing your Startup - http://www.microsoft.com/technet/sysinternals/default.mspx
  MS - MVP - Elephant Boy computers - don't panic!