Error "NTLDR is missing" in the Windows XP computer.

Similar Questions

• Error - NTLDR is missing from the Windows XP computer.

  Original title: difficulty ntldr missing.

  I don't have xp recovery disk. I get lack ntldr message at startup. How can I fix wihout disc?

  Since the MS Answers forum does not prompt for any information system when a new question is asked, we know absolutely nothing about your system.  What makes which gives good ideas for extremely difficult solution.

  Provide information on your system, the better you can:

  What is your system brand and model?

  What is your Version of XP and the Service Pack?

  Your system have IDE or SATA disks?

  Describe your current antivirus and software anti malware situation: McAfee, Symantec, Norton, Spybot, AVG, Avira!, MSE, Panda, Trend Micro, CA, Defender, ZoneAlarm, PC Tools, Comodo, etc..

  The question was preceded by a loss of power, aborted reboot or abnormal termination?  (this includes the plug pulling, buttons power, remove the battery, etc.)

  The afflicted system has a working CD/DVD (internal or external) drive?

  If the system works, what do you think might have changed since the last time it did not work properly?

  You can create a bootable CD from the Console of the Recovery XP (no XP media required) and start the XP Recovery Console.

  The chances are pretty good that there is a copy of the NTLDR file on your system to another location, so you can replace the missing file.

  The file is supposed to be like c:\ntldr c:\ root folder (note there is no file for the ntldr file extension) but of course your seems to have developed missing.

  If your system is preinstalled with XP there is probably a folder c:\i386 on your system and that there should be a copy of the file in folder c:\i386 NTLDR.

  If you have installed Service Pack 3 download Internet via the World Wide Web Wide, there will be a copy of the NTLDR file in this folder:

  c:\Windows\ServicepackFiles\i386

  Once you get started the recovery console and you ran chkdsk/r, I would see if these commands will work for you to replace the missing file:

  copy c:\i386\ntldr c:\

  or

  copy c:\windows\servicepackfiles\i386\ntldr c:\

  Here's how to make a CD of bootable XP Recovery Console and I would run the chkdsk /r FIRST to make sure that your file system is not damaged.

  Boot into the Recovery Console Windows using an XP bootable installation CD.

  If you have no XP bootable media (or aren't sure you have) create a bootable XP Recovery CD of Console and do not forget.

  This is not the same as recovery disks that might have come with the acquisition of the system store.

  You can make a bootable Recovery Console CD by downloading an ISO file and burn it to a CD.

  The ISO bootable image file you need to download is called:

  xp_rec_con. ISO

  Download the ISO from here:

  http://www.mediafire.com/?ueyyzfymmig

  Use a new CD and this simple and free program to burn your ISO file and create your bootable CD:

  http://www.ImgBurn.com/

  When you install ImgBurn, DO NOT install the Ask toolbar.

  Here are some instructions for ImgBurn:

  http://Forum.ImgBurn.com/index.php?showtopic=61

  It would be a good idea to test your bootable CD on a computer running.

  You may need to adjust the computer BIOS settings to use the CD-ROM drive as the first device to boot instead of the hard drive.  These adjustments are made before Windows tries to load.  If you miss it, you will need to restart the system again.

  When you start on the CD, follow the instructions:

  Press any key to boot from CD...

  Installing Windows... going to pronounce.

  Press 'R' to enter the Recovery Console.

  Select the installation that you want to access (usually 1: C:\WINDOWS)

  You may be asked to enter the password (usually empty).

  You should be in the folder C:\WINDOWS.  It's the same as the

  C:\Windows folder that you see in Solution Explorer.

  The Recovery Console allows base as file commands: copy, rename, replace, delete, chkdsk, fixboot, fixmbr, cd, etc.

  For a list of the commands in the Recovery Console, type help at the prompt of commands or read on here XP Recovery Console:

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/recovery_console_cmds.mspx?mfr=true

  A good idea before you start things must first verify the integrity of your file system by using the chkdsk command.

  In the command prompt window, run the chkdsk command on the drive where Windows is installed to try to fix any problems on the afflicted player.

  Running chkdsk is fine, even if he finds no problem.  It won't hurt anything to run it.

  Assuming your boot drive is C, run the following command:

  CHKDSK C: /r

  Let chkdsk finish to correct the problems, he could find.

  It may take a long time for chkdsk complete or they seem to be "stuck".  Be patient.  If the HARD drive led blinks always, chkdsk is something.  Keep an eye on the amount of the percentage to be sure that it is still making progress.  It may even seem to go back sometime.

  You must run chkdsk/r again until it finds no error to correct.

• Download error - cannot download anything on the windows vista computer.

  When I try to download anything, it says that Windows cannot find 'C:\Users\Admin\Downloads\shockwave_Installer_Slim.exe '. Then he said, make sure you typed the name correctly and then try again. I hope you can help me.

  Original title: download error

  Hello

  Thanks for posting your query in the Microsoft Community Forums.

  It seems that you have problems with downloading files on the windows vista computer.

  The description of the problem seems a little unclear and I wish I had a better understanding before you start working on it. I would appreciate if you can help me with the following information.

  1. what browser you use on the computer?

  2. What is the exact full error message?

  3. don't you make changes on the computer before this problem?

  4. deal with this problem if you try to download all files from online?

  If you do this in the face of Internet Explorer help, I suggest that you should change the default download location and check if it helps.

  Method 1

  In internet explorer, you can change the default location.

  Here's how:

  a. open internet explorer.

  b. click on Tools , then select view downloads.

  c. downloads for window, click Options.

  d. now, enter the default download location and click on the OK button.

  Turn on the computer at the beginning of boot and check if the problem persists.

  Method 2

  Perform a clean boot to see if no third-party service is causing the problem.

  To help resolve the error and other messages, you can start Windows by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  http://support.Microsoft.com/kb/929135

  Note: follow step 3 to reset the computer to start as usual after the boot process.

  For your reference:

  Windows Internet Explorer 9 Download Manager using

  http://Windows.Microsoft.com/en-in/Windows-Vista/using-download-manager-in-Internet-Explorer

  Response with more information to help you.

  Let us know if you encounter problems under windows in the future. We will be happy to help you.

• NTLDR is missing on the Windows 7 client

  Help, please...  I am a newbie to VM.  I have installation of VMware Workstation 7.1 on xp 32-bit home as host.  I am trying to run WIndows 7 as a guest.  When I turn on VM to windows 7, I get NTLDR is missing Press Ctrl + Alt + Delete to restart.  I've tried everything.  I disabled the floppy drive and CD-ROM.  I'm stuck please help!  Thank you. P.S. I can boot Windows 7 through the Bios indepentently and it works fine.

  Welcome to the community,

  have you installed the virtual machine by using the Easy Install feature? Please check the virtual disk is not connected (connection on startup is disabled) and remove or rename the autoinst.flp in the folder of the virtual machine.

  André

• Error - PowerPC processor driver is missing from the Windows 7 computer.

  Original title: AlienWare Area 51 PowerPC driver problem.

  Hello, I have the above listed computer. Device Manager is indicating that there is a PowerPC processor driver is missing and Windows(7 Ultimate) fails to locate a suitable driver. I have the CD of resources provided with the system and I don't see anything here on this Web site, or anywhere on the web, all that talk about it. The only thing I find is realted to Mac and I understand I have an old iBookG4 with a PPC, but it is certainly not one of these... it is brand new and State of the art. It is in fact a customer and I would like to get him full here tomorrow afternoon. Help, please. Let me know if you need additional information.

  I throw a Gigabyte Mobo, I have not installed the network Killer driver, which uses the RJ45 for Ethernet. to design MGR it displays processor PowerPC, no driver installed check that you have the hardware for this port, or if a nic on PCI, the killer network card is part of the network Bigfoot hardware which be may installed on your motherboard. If you installed the motherboard disk and network drivers but shows again no driver it could be a problem with the hardware, but check the exact hardware on your Board and make sure that the drivers are installed for each part of the network. Material of Bigfoot and serial killer.                odiebugs.

• Error "NTLDR is missing when the computer starts".

  Originalt title: NILDR error code

  HELLO > DELETED MY SOFTWARE NILDR BY MISTAKE, this MEANS THAT I CAN'T START MY COMPUTOR OR GO ON THE WEBB TRIED THE Ctrl + Alt + Delete KEY, BUT IT DOES NOT WORK. I JUST NEED TO GET BACK TO UNTIL I DELETED THE DRIVERS. I CAN'T USE MY MACHINE AT ALL UNTIL I HAVE TO RESTORE MY NILDR? BY THE WAY CAN USE RESTORE AT AN EARLY DATE BECAUSE CAN NOT OPEN MY COMPUTOR > HELP HELP

  Hi Go ELLIOTT,
   
  I suggest you for this visit provided Microsoft KB article below and check if the problem is resolved.
   
  An NTLDR or NTDETECT.COM not found error
  http://support.Microsoft.com/kb/555304
   

  Thank you, and in what concerns:
  I. Suuresh Kumar - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  

• Code 39 error sometimes no noise in the Windows XP computer.

  Original title: Audio device is turned off and that it was not fixed.

  Dell Dimension 8400 Pentium 4 processor 3.2 GHz, Windows XP Edition Version 2002 service pack 3 family. Card Creative Sound Blaster Live 24 bit sound.

  Sound turns off sometimes. Manager device poster of yellow question mark on the mixer audio ms kernel wave. Properties shows corrupted driver error 39... Restart the computer and it works fine again once, but sound goes out after a few days.

  Not a speaker issue, they work very well, watch the sound card as working in Device Manager when sound is on.

  I ran the utility of automated troubleshooting and it is said that an audio device is cut off and it was not fixed. How to activate audio device?  I went to the volume control, it shows not as muted.  Terribly frustrated

  Sometimes a single application overlaps or another in a way to talk about the covers.  Both deal with sound, so there may be files that coordinate with each other.  Uninstall/reinstall puts it at a stage of default configuration.

  Try to reinstall the application and see if the sound works.  That's the problem in a sound broadcast like yours.

• MSN icon is missing from the Windows XP computer.

  Original title: where is my Butterfly Microsoft last?

  Last night, I opened my e-mail through the Microsoft Butterfly. Today, the icon was missing at all locations, including programs. How can I get it back and get to my email which is registered on my computer?

  Hi Rose,

  In dealing with the problem with MSN mail, I recommend you to contact MSN support for help.

  How to contact MSN customer service

  Hope the helps of information.

• Had an error "NTLDR is missing" while restarting the virtual computer

  Hi all

  I got an error "NTLDR is missing" while restarting the virtual computer on which windows is running.

  Can someone please suggest a way out of this error?

  Thank you

  Jenish

  You have a connected to the virtual machine floppy image? If so, disconnect the diskette drive.

• Miss me the windows system32 rundll32.exe. I can't access the Add/Remove in the control panel.

  original title: missing file

  Miss me the windows system32 rundll32.exe. I can't access the Add/Remove in the control panel.

  I tried to start - run with my c/d operating system

  I checked for viruses

  I purchase software to remove etc and REG files.

  Now that the devil do?

  Thank you

  If this

  I tried to start - run with my c/d operating system

  means that you have tried to use sfc/scannow from start > run, your experience is not surprising.  This 'solution' is often suggested by people who don't really understand what this command does.  It does not help to restore a missing rundll32.exe file.

  For what is

  I checked for viruses

  What is the name and version of your anti-virus application?  When (approximately) their subscription expires? What other antimalware applications installed?  What other antimalware applications you used recently to scan your computer?

  If you have not yet used the "software to remove the REG files and etc." return for refund or throw it out.  "Registry cleaners", 'tuners', etc. are not useful.  If you used to "clean" the registry, use its "undo" feature (if it has one) to restore the registry.  Longtime MS MVP PA Bear:

  TIP: If you still think again your registry database must be cleaned, repaired, amplified, to the point, healed, twisted, fixed, enlarged, "swept" or optimized (it isn't), read http://aumha.net/viewtopic.php?t=28099 and draw your own conclusions. See also http://blogs.technet.com/markrussinovich/archive/2005/10/02/registry-junk-a-windows-fact-of-life.aspx

  What probably happened is that your antivirus application deleted or quarantined in your file rundll32.exe thinking he was infected.  He could have, but probably not.  In any case, read the post that begins, "That 'solution' is not on my list." in the following thread: http://answers.microsoft.com/en-us/windows/forum/windows_xp-performance/systemrundllexe-not-found/6e30aff2-a88e-4d86-a654-753d54f632d1 you can also read the rest of the posts in this thread.

  Note that c:\windows\system32\dllcache is a hidden folder, but you who type in the address bar of Windows Explorer (or copy and paste), the folder should open anyway.

  Assuming you manage to restore rundll32.exe, download, install, update and run full scans (not at the same time) with each of the following free tools.

  MalwareBytes AntiMalware
  SUPERAntiSpyware

• Error: Failed to setup of the Windows updates. Restoration of the changes. Do not turn off your computer when you try to install Windows updates

  I got an error message in step 2 of configuring updates - "updates were not correctly configured.  Returning from changes' anyone can help solve this problem?

  Error: Failed to setup of the Windows updates. Restoration of the changes. Do not turn off your computer when you try to install Windows updates
  http://support.Microsoft.com/kb/949358

• I get the 0x8078012D error code when I run the Windows backup on an external hard drive.

  I get the 0x8078012D error code when I run the Windows backup on an external hard drive.  I have Windows 7 Professional.  That suggests this error code is the problem and how can I solve the problem?

  For people who read this thread, I offer the following information.  I solved the problem by noticing that the problem could have been caused, when the system image is created.  So I did a backup without creating the system image and backup is complete without error.

  Then I used the backup program to create a system image.  This time error (0x8007045D) was displayed.   The error report says "the operation failed for a device error encountered with the source or the destination. If the volume of the source or the destination is on a disk, run CHKDSK /R on the source volume or destination and then try again using. »

  So I ran chkdsk/r, and this program is a bad sector on the hard drive of my computer and fixed the error.  It took about an hour to run the program.  Now, the image of the system and the backup of data file work again.

  So I think that the main cause of error (0x8078012D) is deborahgarbe of i/o error (0x8007045D).  So if you get the first error code you can search for fixes for the second error code fix the root cause.

• Error of 0x8007042c, cannot start the Windows Firewall

  Original title: error 0x8007042c, you cannot start the Windows Firewall

  Help

  I can't have the windows firewall to install and run...

  I have a picture of a mistake, but I don't know how to post the photo of the error here.

  Firewall Windows cannot change some of your settings
  Error code;   0x8007042C

  Concerning

  Bill

  E-mail address is removed from the privacy *.

  Old man again on XP PRO

  Hi Dan,.
   
  You might have a corrupted user profile, I'd like you to create a new user account and test the question.
  http://Windows.Microsoft.com/en-us/Windows7/create-a-user-account
   
  Aziz Nadeem - Microsoft Support

  [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]

• How can I get sound on the Windows XP computer with an HDMI instead of DVi cable?

  How can I get the sound on the Windows XP computer using an HDMI instead of DVI cable - my monitor accepts cables but

  I don't know how to make it work with the HDMI - help interface? Thank you!

  The question is not what operating system you have (a version of XP), but if your video card has an HDMI output.

  See http://www.bhphotovideo.com/indepth/computers/tips-solutions/how-connect-pc-hdmi-tv

  If you need specific advice on your computer, follow these steps:

  • Open system information (start > run > msinfo32.exe > OK)
  • Click in the system information window and select all (CTRL + A) and copy (CTRL + C)
  • Paste (CTRL + V) into your answer here
  • Return to system information and click on the + sign next to "Components" and then click "display".
  • Select all (CTRL + A) and then copy (CTRL + C)
  • Paste (CTRL + V) into your response at the end of the previous data

• Is node/host usually means a client computer or it means that the window Server computer?

  Is node/host usually means a client computer or it means that the window Server computer?

  Hi stuckfree,

  The question you posted would be better suited for the TechNet community. Please refer to the link and post your request for more information.