Error on the motherboard

Similar Questions

• a610n - fan error of the system after replacing the motherboard

  Hi all

  I just replaced the motherboard on my system (phone http://h30434.www3.hp.com/t5/Desktop-Hardware/M2N68-LA-Narra-2-Replacement/td-p/3711774) and now I get this error when starting: Fan failure system, PC service to avoid any damage. I thought it was the CPU fan but he was running and after some research, I realized that he could talk a case fan.

  As a side note, the motherboard, I had was a little different and missing 2 connections that seem to be the front mic/headphone and USB ports.

  Now, the case's fan then what really is the problem? Any ideas anyone?

  Thank you

  -Panos

  The rev3.02 of M2N68 - THE Committee a case fan rear 3 poles. See here.

  The CPU fan is a 4 pin cable and attaches to the appropriate header to 4 pins on the motherboard. See the representative schema above.

  As for you, another question, the front USB port attaches to a USB connector on the card.

• Error BSOD 0x7B after changing the motherboard

  Hello

  I bought a new motherboard + CPU + RAM last week and I am fighting to get my windows to start again...

  I tried many things, and yesterday I managed to access the Safe Mode...

  So in safe mode, the drivers have been installed. With the exception of USB USBSTOR because mass storage. SYS has been the cause of a black screen error message, so I managed to rename it to usbstor.sys.old...

  In any case, 99% of my new motherboard drivers seem to be installed...

  Now when I try to start, I get a blue screen:

  "A problem has been detected and windows has shut down to prevent damage to your computer...".

  ...

  Check for viruses on your computer. Remove the newly installed hard drives...

  Technical information

  STOP: 0X0000007B (...

  Hello

  Motherboard is obviously not 100% identical if this can be the same model.

  Install the latest version of the BIOS and drivers for the chipset of the motherboard machine. If this doesn't help, you will need to clean install Windows.

  Read these:

  Bug Check 0x7B: INACCESSIBLE_BOOT_DEVICE
  https://msdn.Microsoft.com/en-us/library/Windows/hardware/ff559218 (v = vs. 85) .aspx

  Bug Check 0x7B: INACCESSIBLE_BOOT_DEVICE
  * 1138.html? order = votes http://www.faultwire.com/solutions-fatal_error/Check-for-viruses-on-your-Computer-0x0000007B-

  That Bug_Check is usually FATAL. It is useless to try to analyze the minidump because the cause is the change of equipment.

  Sorry it's not better communicated.

  I hope this helps.
  --------------------------------------------------------------------------------------------
  Rob Brown - Microsoft MVP<- profile="" -="" windows="" and="" devices="" for="" it :="" bicycle="" -="" mark="" twain="" said="" it="">

• Kernel Panic after the change of the motherboard and the installation of El Capitan

  Hi guys,.

  So I have this 2011 machine that has caused me a lot of headaches with graphics, because of which the motherboard has been replaced under extended warranty and El Capitan was installed shortly after. Everything was fine for about 3 months and now the machine started crashing from time to time. The last time it crashed I had 1 million tabs open in Firefox and after opening another, distorted sound and it crashed. (This was never a problem before). During reboot, the screen was almost completely black, you can see the progress bar, but really dim. On reboot, it gave me this report. I don't really know how to interpret it, I'd appreciate any help on your part, thank you!

  Anonymous UUID:

  EE8DFD0F-044F-A5E7-88AD-9165D7EBBBC1

  Sun Mar 20 10:00:44 2016

  Panic report *.

  panic (cpu 6 0xffffff802dbd6bba appellant): Kernel trap at 0xffffff7fb08c1925, type 14 = page fault, registers:

  CR0: 0 X 0000000080010033, CR2: 0 X 0000000000000050, CR3: 0X000000011164A0A8 CR4: 0X00000000000626E0

  RAX: 0 X 0000000000000052, RBX: 0 X 0000000000000000, RCX: 0XFFFFFF804ED00000 RDX: 0 X 0000000000000217

  RER: 0XFFFFFF8138393950, RBP: 0XFFFFFF8138393960, IHR: 0 X 0000000000000000, RDI: 0XFFFFFF80424AA000

  R8: 0 X 0000000000000000, R9: 0XFFFFFF81294063C0, R10: 0X0000000000D10B40 R11: 0 X 0000000000000002

  A12: 0 X 0000000000000000 R13: 0 X 0000000000000052, R14: 0 X 0000000000000217, R15: 0XFFFFFF80424AA000

  RFL: 0 X 0000000000010202, RIP: 0XFFFFFF7FB08C1925, CS: 0000000000000008, SS 0 X: 0 X 0000000000000010

  Lack of CR2: 0 x 0000000000000050, error code: 0 x 0000000000000000, CPU error: 0 x 6, PL: 0

  Backtrace (CPU 6), frame: return address

  0xffffff81383935e0: 0xffffff802dae5307

  0xffffff8138393660: 0xffffff802dbd6bba

  0xffffff8138393840: 0xffffff802dbf4313

  0xffffff8138393860: 0xffffff7fb08c1925

  0xffffff8138393960: 0xffffff7fb08c47b0

  0xffffff81383939a0: 0xffffff7fb08b941c

  0xffffff81383939f0: 0xffffff7fb08182e0

  0xffffff8138393a20: 0xffffff7fb08c1bb3

  0xffffff8138393a50: 0xffffff7fb08186af

  0xffffff8138393a80: 0xffffff7fb081e37c

  0xffffff8138393ac0: 0xffffff7fb0816829

  0xffffff8138393b50: 0xffffff802e0e3c82

  0xffffff8138393b80: 0xffffff802e0e48fa

  0xffffff8138393be0: 0xffffff802e0e1967

  0xffffff8138393d20: 0xffffff802dba07d0

  0xffffff8138393e30: 0xffffff802dae9aa3

  0xffffff8138393e60: 0xffffff802dacd478

  0xffffff8138393ea0: 0xffffff802dadcfd5

  0xffffff8138393f10: 0xffffff802dbc13aa

  0xffffff8138393fb0: 0xffffff802dbf4b36

  	Extensions of core in backtrace:
  	com.apple.iokit.IOAcceleratorFamily2 (203.10) [008AEFEE-8690-3E1C-B644-E4FDF37B44B 0]@0xffffff7fb0812000-> 0xffffff7fb087dfff]
  	dependency: com.apple.iokit.IOPCIFamily (2.9) [8E5F549E-0055-3C0E-93F8-E872A048E31B] @ 7fae32d000 0xffffff
  	dependency: com.apple.iokit.IOGraphicsFamily (2.4.1) [48AC8EA9-BD3C-3FDC-908D-09850215AA32] @0 xffffff7faee2d000
  	com.apple.AMDRadeonX3000 (1.3.8) [CB3CE8B0-A439-3290-A661-401AAB9E4FBE] @0xffffff7f b088c000-> 0xffffff7fb0ce7fff
  	dependency: com.apple.iokit.IOPCIFamily (2.9) [8E5F549E-0055-3C0E-93F8-E872A048E31B] @ 7fae32d000 0xffffff
  	dependency: com.apple.iokit.IOGraphicsFamily (2.4.1) [48AC8EA9-BD3C-3FDC-908D-09850215AA32] @0 xffffff7faee2d000
  	dependency: com.apple.iokit.IOAcceleratorFamily2 (203.10) [008AEFEE-8690-3E1C-B644-E4FDF37B44 B0]@0xffffff7fb0812000

  Corresponding to the current thread BSD process name: firefox

  Mac OS version:

  15B 42

  Kernel version:

  Darwin Kernel Version 15.0.0: Sat Sep 19 15:53:46 PDT 2015; root:XNU-3247.10.11~1/RELEASE_X86_64

  Kernel UUID: AB5FC1B4-12E7-311E-8E6F-9023985D8C1D

  Slide kernel:

  0x000000002d800000

  Text of core base: 0xffffff802da00000

  Text __HIB base: 0xffffff802d900000

  Name of system model: MacBookPro8, 2 (Mac-94245A3940C91C80)

  Availability of the system in nanoseconds: 280943144553392

  last load kext to 242438409180848: com.apple.driver.AppleXsanScheme 3 (addr 0xffffff7fb155b000 size 32768)

  Finally unloaded kext to 242512793581004: com.apple.driver.AppleXsanScheme 3 (addr 0xffffff7fb155b000 size 32768)

  kexts responsible:

  com.rim.driver.BlackBerryUSBDriverInt 0.0.67

  com Apple.filesystems.smbfs 3.0.0

  com.apple.driver.AppleHWSensor 1.9.5d0

  com.apple.driver.AudioAUUC 1.70

  com.apple.driver.AGPM 110.20.21

  com Apple.filesystems.autofs 3.0

  com.apple.iokit.IOBluetoothSerialManager 4.4.2f1

  com.apple.driver.AppleOSXWatchdog 1

  com.apple.driver.AppleMikeyHIDDriver 124

  com.apple.driver.AppleMikeyDriver 272.50.31

  com.apple.driver.AppleUpstreamUserClient 3.6.1

  com.apple.driver.AppleHDA 272.50.31

  com Apple.Driver.pmtelemetry 1

  com.apple.kext.AMDFramebuffer 1.3.8

  com.apple.iokit.IOUserEthernet 1.0.1

  com.apple.driver.AppleIntelHD3000Graphics 10.0.0

  com.apple.Dont_Steal_Mac_OS_X 7.0.0

  com.apple.driver.AppleHV 1

  com.apple.driver.AppleThunderboltIP 3.0.8

  com.apple.AMDRadeonX3000 1.3.8

  com.apple.iokit.BroadcomBluetoothHostControllerUSBTransport 4.4.2f1

  com.apple.driver.AppleSMCPDRC 1.0.0

  com.apple.driver.AppleLPC 3.1

  com.apple.driver.AppleSMCLMU 208

  com.apple.driver.AppleIntelSlowAdaptiveClocking 4.0.0

  com.apple.driver.AppleMCCSControl 1.2.13

  com.apple.driver.AppleMuxControl 3.11.33b1

  com.apple.driver.ACPI_SMC_PlatformPlugin 1.0.0

  com.apple.driver.AppleIntelSNBGraphicsFB 10.0.0

  com.apple.kext.AMD6000Controller 1.3.8

  com.apple.driver.SMCMotionSensor 3.0.4d1

  com.apple.driver.AppleUSBTCButtons 245,4

  com.apple.driver.AppleUSBTCKeyboard 245,4

  com.apple.driver.AppleIRController 327,5

  com.apple.AppleFSCompression.AppleFSCompressionTypeDataless 1.0.0d1

  com.apple.AppleFSCompression.AppleFSCompressionTypeZlib 1.0.0

  com.apple.BootCache 37

  com.apple.iokit.SCSITaskUserClient 3.7.7

  com.apple.iokit.IOAHCIBlockStorage 2.8.0

  com.apple.driver.AirPort.Brcm4331 800.20.24

  com.apple.driver.AppleSDXC 1.7.0

  com.apple.iokit.AppleBCM5701Ethernet 10.1.11

  com.apple.driver.AppleFWOHCI 5.5.2

  com.apple.driver.usb.AppleUSBEHCIPCI 1.0.1

  3.1.5 com.apple.driver.AppleAHCIPort

  com.apple.driver.AppleSmartBatteryManager 161.0.0

  com.apple.driver.AppleRTC 2.0

  com.apple.driver.AppleACPIButtons 4.0

  com.apple.driver.AppleHPET 1.8

  com.apple.driver.AppleSMBIOS 2.1

  com.apple.driver.AppleACPIEC 4.0

  com.apple.driver.AppleAPIC 1.7

  com.apple.driver.AppleIntelCPUPowerManagementClient 218.0.0

  com Apple.NKE.applicationfirewall 163

  com Apple.Security.Quarantine 3

  com.apple.security.TMSafetyNet 8

  com.apple.driver.AppleIntelCPUPowerManagement 218.0.0

  com.Apple.Driver.USB.Networking 5.0.0

  com Apple.nke.PPP 1.9

  com Apple.kext.Triggers 1.0

  com.apple.iokit.IOSerialFamily 11

  com.apple.driver.DspFuncLib 272.50.31

  com.apple.kext.OSvKernDSPLib 525

  com.apple.iokit.IOSurface 108.0.1

  com.apple.driver.CoreCaptureResponder 1

  com.apple.iokit.IOFireWireIP 2.2.6

  com.apple.iokit.IOAcceleratorFamily2 203.10

  com.apple.iokit.IOBluetoothHostControllerUSBTransport 4.4.2f1

  com.apple.iokit.IOBluetoothFamily 4.4.2f1

  com.apple.driver.AppleHDAController 272.50.31

  com.apple.iokit.IOHDAFamily 272.50.31

  com.apple.iokit.IOAudioFamily 204,1

  com.apple.vecLib.kext 1.2.0

  com.apple.iokit.IOSlowAdaptiveClockingFamily 1.0.0

  com.apple.driver.AppleSMBusPCI 1.0.14d1

  com.apple.driver.AppleSMBusController 1.0.14d1

  com.apple.driver.AppleBacklightExpert 1.1.0

  com.apple.iokit.IONDRVSupport 2.4.1

  com.apple.driver.AppleGraphicsControl 3.11.33b1

  com.apple.driver.IOPlatformPluginLegacy 1.0.0

  com.apple.driver.IOPlatformPluginFamily 6.0.0d7

  com.apple.kext.AMDSupport 1.3.8

  com.apple.AppleGraphicsDeviceControl 3.11.33b1

  com.apple.iokit.IOGraphicsFamily 2.4.1

  com.apple.driver.AppleSMC 3.1.9

  com.apple.driver.AppleUSBMultitouch 250.4

  com.apple.iokit.IOUSBHIDDriver 900.4.1

  com.apple.driver.CoreStorage 517

  com.apple.driver.usb.AppleUSBHostCompositeDevice 1.0.1

  com.apple.driver.usb.AppleUSBHub 1.0.1

  com.apple.iokit.IOSCSIMultimediaCommandsDevice 3.7.7

  com.apple.iokit.IOBDStorageFamily 1.8

  com.apple.iokit.IODVDStorageFamily 1.8

  com.apple.iokit.IOCDStorageFamily 1.8

  com.apple.driver.AppleThunderboltDPInAdapter 4.1.2

  com.apple.driver.AppleThunderboltDPAdapterFamily 4.1.2

  com.apple.driver.AppleThunderboltPCIDownAdapter 2.0.2

  com.apple.iokit.IOAHCISerialATAPI 2.6.2

  com.apple.driver.AppleThunderboltNHI 4.0.4

  com.apple.iokit.IOThunderboltFamily 5.0.6

  com.apple.iokit.IOEthernetAVBController 1.0.3b3

  4.5.8 com.apple.iokit.IOFireWireFamily

  1101.24 com.apple.iokit.IO80211Family

  com.apple.driver.mDNSOffloadUserClient 1.0.1b8

  com.apple.iokit.IONetworkingFamily 3.2

  com Apple.Driver.corecapture 1.0.4

  com.apple.iokit.IOAHCIFamily 2.8.0

  com.apple.driver.usb.AppleUSBEHCI 1.0.1

  com.apple.driver.AppleEFINVRAM 2.0

  com.apple.driver.AppleEFIRuntime 2.0

  com.apple.iokit.IOHIDFamily 2.0.0

  com.apple.iokit.IOSMBusFamily 1.1

  com Apple.Security.sandbox 300.0

  com.apple.kext.AppleMatch 1.0.0d1

  com.apple.driver.AppleKeyStore 2

  com.apple.driver.AppleMobileFileIntegrity 1.0.5

  com.apple.driver.AppleCredentialManager 1.0

  com.apple.driver.DiskImages 415

  com.apple.iokit.IOReportFamily 31

  com.apple.driver.AppleFDEKeyStore 28.30

  com.apple.iokit.IOUSBMassStorageClass 4.0.0

  com.apple.driver.AppleUSBComposite 900.4.1

  com.apple.iokit.IOSCSIBlockCommandsDevice 3.7.7

  com.apple.iokit.IOSCSIArchitectureModelFamily 3.7.7

  com.apple.iokit.IOStorageFamily 2.1

  com.apple.iokit.IOUSBFamily 900.4.1

  com.apple.iokit.IOUSBHostFamily 1.0.1

  com.apple.driver.AppleUSBHostMergeProperties 1.0.1

  com.apple.driver.AppleACPIPlatform 4.0

  com.apple.iokit.IOPCIFamily 2.9

  com.apple.iokit.IOACPIFamily 1.4

  com.apple.kec.Libm 1

  com Apple.KEC.pthread 1

  com Apple.KEC.corecrypto 1.0

  Model: MacBookPro8 2, MBP81.0047.B2A of BootROM, 4 processors, Intel Core i7, 2.2 GHz, 8 GB, MSC 1.69f4

  Graphics card: integrated Intel HD Graphics 3000, Intel HD Graphics 3000,

  Graphics card: AMD Radeon HD 6750 M, AMD Radeon HD 6750 M, PCIe, 1024 MB

  Memory module: DIMM0/0 BANK, 4 GB DDR3, 1333 MHz, 0 x 0198, 0x393955353432382D3034322E413030472020

  Memory module: DIMM0/1 BANK, 4 GB DDR3, 1333 MHz, 0 x 0198, 0x393955353432382D3034322E413030472020

  Airport: spairport_wireless_card_type_airport_extreme (0x14E4, 0xD6), Broadcom BCM43xx 1.0 (5.106.98.100.24)

  Bluetooth: Version 4.4.2f1 16391, 3 services, 18 aircraft, 1 incoming serial ports

  Network service: Wi - Fi, AirPort, en1

  Serial ATA Device: TOSHIBA MK7559GSXF, 750,16 GB

  Serial ATA Device: MATSHITADVD-R UJ-898

  USB device: USB 2.0 Bus

  USB device: FaceTime HD camera (built-in)

  USB device: Hub

  USB device: Apple keyboard / Trackpad

  USB device: Hub BRCM2070

  USB Device: USB Bluetooth host controller

  USB device: USB 2.0 Bus

  USB device: Hub

  USB Device: IR receiver

  Bus crush: MacBook Pro, Apple Inc., 22.1

  If you no longer have a Blackberry, rid the MBP of all files of the RIM.  Look at the developers wen site for instructions.

  Delete Firefox and run the MBP without it.   See if the panic stop.  Test and then put it back.  (what is the point of maintaining that a 'million' tabs open).

  Ciao.

• Work 6 GB/s hard drive IDE oucederomsurlesecondport 3 Gbit/s of the motherboard?

  Hi-
  
  I have HP Compaq DC7700 Convertible Minitowers desktop for home use.
  http://h20565.www2.HP.com/portal/site/hpsc/template.page/public/KB/docDisplay/?sp4ts.Oid=3232028 & SPF...
  
  I would like to repalce the HDD (Seagate 160 GB, SATA 3 GB/s) as its problems donations.
  
  (1) do you think that any disk SSD will work with the above motherboard?
  
  (2) if not, SATA 6 GB/s Hard drive with 3 GB/s port of the motherboard above?
  
  (3) these discs hard SATA2 and SATA3 having the same type of power outlet?

  Hello:

  You may encounter a problem if you are installing a drive not HP SATA III any like I did with my dc7800.

  My PC has the first question appears on the document of support on the link below (even if the dc7800 was not among the list of the PCs).

  http://h20566.www2.HP.com/portal/site/hpsc/template.page/public/KB/docDisplay/?javax.portlet.begCacheTok=com.vignette.cachetoken & javax.portlet.endCacheTok = com.vignette.cachetoken & javax.portlet.prp_ba847bafb2a2d782fcbb0710b053ce01=wsrp-navigationalState%3DdocId%253Demr_na-c02711513-3%257CdocLocale%253D%257CcalledBy%253D & javax.portlet.tpst = ba847bafb2a2d782fcbb0710b053ce01 & sp4ts.oid = 3718645 & ac.admitted = 1379354458533.876444892.199480143

  I had bought a HDD WD Caviar Black 500 GB SATA III and every time I want to reboot the PC or several times in a cold, start I'd get a disc hard not found error.

  Of course, I assumed it was a defective and returned for a replacement disc.  The spare drive did the same thing.

  I have a HP 8200 Elite CMT with a Seagate 1 TB SATA III hard drive.  I put this drive in my dc7800 and it worked perfectly for the last two years, who confirmed to me that the support document affects more than the models listed.

  My recommendation for you would be to get the equivalent Seagate HDD which was in my Elite 8200, which is this one or stick with a SATA II if you can find one.

  http://www.Amazon.com/DP/B004IZN3YI/?tag=mh0b-20 & hvadid = 2478383168 & ref = pd_sl_8m29k5ycix_e

• Satellite P20-932 PSP26E - on the motherboard PCI resource conflict

  Hello
  I have a Toshiba P20 932
  REF.: PSP26E-02NH9-GR
  with Windows XP

  In a first step, that the USB port not working, I reinstalled Windows XP with the drivers from the Internet for Toshiba Satellite P20.
  When I start now the following events occur:

  1. Press Start button
  TOSHIBA screen
  Press [F2] for INSTALLATION. Press [F12] to the boot device selection Menu
  1.1 if I press F2 - replace the following screen:
  ? BQ01 BIOS Version V1.10
  CPU = Intel (R) Pentium (R) 4 CPU 3.00 GHz
  ? M 047 system RAM passed
  ? 12K Cache SRAM passed
  System BIOS with a shadow
  Video BIOS with a shadow
  Fixed disk 0:...
  ATAPI CD-ROM:...
  Initialized the mouse
  ERROR
  Conflict of resources - Bus USB PCI controllers on the motherboard
  Bus: 02, device: 00, function: 00

  Press [F2] for installation

  1.1.1. If I press F2 - nothing happens

  1.2. If I press F12: nothing happens

  2. If I press ESC and start the computer, it changes immediately on the screen 2nd with counting / checking of the system's RAM and Cache SRAM... with the same error. and nothing happens if I press F1 to resume or F2 for Setup.

  Then my laptop is not booting and I do not get access to the BIOS! What can I do?

  Dieter cordially

  Hello

  The error indicates that certain devices that are directly connected to the mobo are in conflict and try to share the same resources. This happens usually when the BIOS has been incorrectly installed or the motherboard is a failure.

  In case you would recommend I affecting the default BIOS. But for that you need access to the BIOS, but it seems that it's not possible.

  It seems to be a motherboard problem. You said that the USB ports do not work. Perhaps this is the reason for the error message and question PCI Serial Bus Controller.
  You have USB devices connected to the laptop?
  If so, just unplug the laptop and check again.

  But what to say; If this does not help, I see a lot of options here. In my opinion the mobo must be replaced if it s really a motherboard problem

• Satellite L650 PXE - E63:error initializing the NIC - error start

  I have a Satellite L650, which is 2 months old.

  The motherboard makes a ticking noise (I think it's what makes noise), and when this noise occurs it causes very slow computer! It has been thus since I got it pretty well.

  Today, the computer makes noise, my itunes music started to jump (it was the only program running) and the computer froze and was told that he could not find windows. When I restart my computer it runs the windows startup repair 7, found nothing wrong, and restarts the computer. When the computer restarts, the screen stays black for a long time... and then it flashes a blue screen (flash is so quick that I have no idea of what he says) and asks if I want to rerun the repair. I choose not to start windows normally... and the screen goes black for a long time, however there is no ticking noise, but it seems that nothing happens.

  If I force a reboot, I get an error message saying along the lines of;

  For Atheros PCIE Ethernet controller... Check the cable connection
  PXE - E63:error initializing the NIC
  PXE - MOF: exit intel PXE ROM
  No device bootable-insert boot disk and press eny key

  Help, please!

  > Today, the computer makes noise, my itunes music started to jump (it was the only program running) and the computer froze and was told that he could not find windows.

  Sounds like the HARD drive failure.
  That would explain the PXE Boot error as well.
  This error occurs if the laptop tries to boot from LAN because other sources bootable couldn t be found.

  In my opinion, you need to replace the HARD drive.
  If the warranty is valid, get in touch with a local ASP from Toshiba and ask the new HARD drive

• IDE 1 error with the new CD player - Satellite 2410-504

  Hello

  Can anyone help please? I have satellite s2410-504 (number PS241E-6HWP1-EN) and my laptop CD drive is dead and I exchanged for a new one and now the IDE 1 error. I presume that he is a master / slave number and the reader has no way to change to cs etc on the drive itself.

  I was told maybe there may be a way to fix this problem of flashing or play with the connections on the motherboard of the ideas please?

  Thank you
  Mel

  You bought the disc is not compatible. It before the BIOS cannot recognize it because bad csel/slave/master settings.
  Of course in the net, some gossip circulating that it should be possible to some flash drives, BUT I also read that, after these procedures, the drive was dead and could not read media.

  I n t recommend something flashing. I guess this drive is new and you must contact the dealer and replace the drive for a new compatible.

• HP pavilion notebook 15 - n03: what is the model number of the motherboard for hp pavilion laptop i3 15-n037cl

  While I put a fan 90 b error and it froze on some video games, it was still under warranty but I wanted not to part with them for weeks and tried to clean it myself, I tore from the power button ribbon clip out of the motherboard and it will not power, my first question is that this will be not covered will be?

  My next question is how would you recommend I rectify this error, what is the motherboard model number, so I can get a replacement? and where can I find some information on the permutation of the cpu and fixing what needs to be fixed, thank you.

  Yes. It's a 3217U i3 with Intel integrated graphics

  So this is the motherboard:

  Intel Core i3-3217U DC 1.8 GHz (3 MB L3 Cache, 1600 MHz DDR3, 17 W) for use with Standard Windows. 737982 501

  Also not in stock at Partsurfer.

• W510: How do I access my data from a failed hard drive after the failure of the motherboard

  I made a mistake and has paid for major .

  This error pouring a drink sweet on my laptop. I know, I know, my keyboard can and protect against damage caused by the spill, but it was a drink together. In any case, I panicked and shut down the system and it has upset and removed the keyboard. And be the impatient person that I am, I made what was probably the ultimate error. I do not give everything save a sufficient amount of time to dry and I tried to boot the system. There is my computer. Or at least I think.

  Symptoms: It began at the start, kept a beep, sometime just close and will start.

  In any case, I guess that my laptop went kaput. Now to the point of this thread. I had not been a recent backup and can't remember when the last backup was actually made. Assuming that my hard drive is ok, I want to get all my data, so I saw several options:

  -Send the system to a data recovery service where I will not pay less than $300, but probably 2 to 3 times what

  -buy an equivalent model laptop and put the HARD drive in there

  -by an external SATA hard drive enclosure and mount it via USB on another computer

  I bought a box external and assembled this evening. I had read about the data access of difficulty with a system non-Lenovo because of encryption of the data. I proved that by linking it to my work (a Dell) laptop and I couldn't access my data directories. If I have access to an another Lenovo Thinkpad, I'll be able to access the data if connected via USB? I had read that I can access the contents of disc hard if it is connected to an another Thinkpad, but I knew not that if it means that I have it connected via SATA connection or if there is work through the USB port.

  I'll appreciate any suggestions for accessing my data.

  Best regards!

  All,

  Thanks for the suggestions.

  I was able to recover my computer and all data on it.

  Just to describe what I have done, here are the details.

  Because of my concern about a failure of the motherboard, I bought a used/given new keyboard and an external SATA drive enclosure. I was not able to properly take possession of the car from my other laptop, but I was able to access the data in Mode without failure. With my data, I plugged the hard drive and the new keyboard in and started without problem.

  Thanks again,

  brent86

• ERROR unsupported CPU, motherboard s5610f H-apricot-RS780L-Μatx, AMD Phenom X 4 965 hdz965fbgmbox

  I have a slimline with card s5610f mother H-apricot-RS780L-Μatx, athlong X 2 250 3.00 GHz.

  BIOS Version 6.05 07/09/2010

  Basic version 08.00.16

  The HP Web site says I can update

  AMD Phenom II X 4 9xx /9xxe/8xx Quad-Core (core Deneb)

  So I tried AMD Phenom X 4 965 hdz965fbgmbox.

  As soon as voltage, the first message I get is "ERROR unsupported CPU...". The PC stops in 10 seconds.

  You have any suggestions.

  By Newegg.com sales information for AMD Phenom II X 4 965 Black Edition (HDZ965FBGMBOX), the power is 125 watts. As 125 watts is more than 95 watts max TDP of the motherboard, the AMD Phenom II X 4 965 Black Edition is not compatible with the card mother H-apricot-RS780L-Μatx.

• STOP: 0x000000D1 ndis.sys error during the Windows Xp Setup screen

  I have a computer tailor-made with a motherboard Intel D865GLC with a p4 running at 2.5 Ghz, a western digital 200 GB HARD drive, a drive Liteon DVD - RW, this computer was recently given too me by a friend because I can not afford the newer hardware. The problem I have is when I do a clean install of windows xp, I randomly get a STOP: 0x000000D1 ndis.sys blue screen. I tried to install an upgrade of windows 98 and windows 2000, nor worked. There is no specific time that he likes to fail, but no matter what it fails, it can be just by copying the files from its installation, the network while it please help

  Thanks in advance

  Nate

  Do not install an operating system is usually caused by (in order of probability):

  1. you are trying to install with other devices connected to the computer. Unplug them before trying to make an installation.

  2. "" "" defective installation media. "" Check the CD/DVD installation for scratches, tasks. Try another machine.

  3. bad optical drive. Test with another CD/DVD bootable or Exchange for a well-known work.

  4. faulty RAM. Test with Memtest86 + www.memtest.org . You will download the .iso image file to create a bootable cd. Burn the file with the third party burning software *-as an image, not in the form of data. Then start with the media that you did (you may need to change the boot priority in your BIOS so that the optical drive is the first boot device). The test runs immediately. The test run for an hour or two--at least that errors are seen immediately. If you get any errors, replace the RAM.

  * It is not necessary to have a third party burning software in Windows 7 since Win7 natively allows to burn an .iso. Other operating systems require it. A good free choice ImgBurn comes from www.imgburn.com .

  5. bad hard drive. Test with a diagnostic utility downloaded from site of the disc mftr... You create a bootable CD with the files you download. Burn the file with a third-party burning software (unless you have Windows 7, that allows to record the .isos natively) - as an image, not in the form of data. Boot with the CD that you have done and do a full test of the reader. The physical tests fail, replace it.

  6. other hardware components are faulty. MS - MVP - Elephant Boy computers - don't panic!

• 6259 analog integrated Output error with the sample clock

  I run into some problems outputing a sinusoid of analog output with my acquisition of data using the sampleclock aboard. At one point, I was able to get the vi works pretty good and repeatable. When revisited however, I started to see error that the driver could not provide the unit with the points quickly. I was running at 250 k 1 k sampling rate a tone to one, but it seems only to be able to get about 20 k, sampling frequency. This creates a pretty rough signal, expecially when the rate fell to 8 k. I produce only 1 second of data.

  See attached bmp. The I/O moved references aren't channels of tasks. Could be the problem? I'm a little frustrated because he has to be a very simple to create vi and I'm having all sorts of problems with it.

  Hi klessm1,

  I want to stress that the behavior you're seeing is atypical - under normal circumstances, DMA transfers must take place fast enough to keep the data in the FIFO embedded permanently until at least the max (2.86 MHz single channel) sampling rate.  After saying that the error you receive indicates that we get no data for the 6259 fast enough for some reason - there are a few options at this point, it should get you operational:

  Remove the need to transfer data to the device.  As Sarah suggested, you can do so by regenerating the on-board FIFO.  The FIFO output on the 6259 is 8 191 samples (shared between the channels), so if you build a periodic signal and this is a sufficient number of samples to characterize a period then this should be a viable option.

  Try using interrupts instead of DMA.  This may seem paradoxical since DMA is generally the fastest method of data transfer on our DAQ hardware, but something rings the Bell with the DMA transfer from your computer to the 6259.  I imagine that you will actually have a faster rate using interrupts if that is the case.

  You can configure the appliance to use only the quantity of memory onboard or interruptions using a channel property node DAQmx (Analog Output > General Properties > advanced > memory and data transfer)

  Implement a delay between the start of the task and the first sample.  If the problem is with the first DMA transfer latency (and not the total throughput on the PCI bus), then adding a delay before attempting to write the first sample should solve the problem.  Some motherboards have been found to have a latency higher than the others (so the question of Sarah #3).

  You can configure the delay with the property node Trigger DAQmx (start > more > Delay / delay units).  This applies even if you do not explicitly have a configured start trigger.

  I think the three above are good ideas to try depending on what you need exactly.  I would also check for updates to the BIOS available for your motherboard that could address the issue (but it would be something that the manufacturer would be more known).  I hope this help - made - know us how it goes!

  -John

• Installation of Windows XP Pro on a new configuration of the motherboard. Installation locks a blue screen during the installation of devices. Assistance from ms said why, but not healing. Anyone know an answer?

  My old motherboard gave the soul, and I have now installed a Gigabyte GA-880GM-UD2H with an AMD Phenom 6 processor and 4 GB of RAM.  The 2 HD is a Maxtor Sata 1 300 GB ones. One is divided into 2 equal partitions, the other has a single partition. During installation, it hangs at a blue screen during the "installing devices" and towards the end of the indicator. Removing everything except the essential, makes no difference.
  With 0x0000000A IRQL_NOT_LESS_OR_EQUAL error message States. This rising on the MS, it indicates:-stop this message indicates that a kernel-mode process or driver tried to access a memory address in which he was not allowed to access. The most common cause of this error is a bad or corrupted pointer that refers to an incorrect location in the memory. A pointer is a variable used by a program to designate a block of memory. If the variable has an incorrect value, the program tries to access memory that it shouldn't. When this occurs in a user mode application, it generates an access violation. When it occurs in kernel mode, it generates a STOP 0x0000000A messages. If you encounter this error during the upgrade to a newer version of Windows, it could be caused by a device driver, system service, a virus scanner, or backup tool which is not compatible with the new version.

  I start with new parts, except the DVD & HDs drive and with a start-up Virgin & installation process. I'm not upgraded to the BONE, that's the one I was using before the reconstruction. The supplier of components, suspected of defective parts and cooperated in the provision of a set of replacement of parts, but there is no change in the problem.

  Can someone explain what I can do to start?   Thank you!

  Hello

  See the article below which might help you.

  You receive an error message "Stop 0x0000000A" in Windows XP
  http://support.Microsoft.com/kb/314063

• Had to replace the motherboard: System does not boot, the XP installation disc runs to a failure.

  Thus, the motherboard in my PC started to die.  I replaced it.  Start-up of the new system has prompted a Safe Mode boot.  Choose Safe Mode, the system restarts after mup.sys.  Choose the last known good startup the initial windows screen appears briefly, then restart the system.  Boot from the original installation disk, all kinds of drivers charge then the last message that appears is loading Windows Executive.  A
  BSOD appears stating something to the effect of an error with the hard drive, verify the presence of virus, remove the new hard disks, etc..  Hard drives is a virus.  So, how do you round a re - install defective and/or repair or a defective Mode start safe mode with new material?

  Thank you

  Hello

  Since you have replaced the motherboard, you may need to reinstall the operating system.
  Reference:
  http://Windows.Microsoft.com/en-us/Windows/help/install-reinstall-uninstall

  Thanks and greetings
  Umesh P - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  [If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message.] [Marking a post as answer, or relatively useful, you help others find the answer more quickly.]