Error preventing printing HP 4000 series

Similar Questions

• LaserJet 4000 TN: The printer HP Laserjet 4000 Series PCL5: error state & quot; message & quot;

  I sent the following message to Microsoft after a ' update:

  I have a printer HP Laserjet 4000 Series PCL5 TN which worked beautifully "black only" for many years. A recent update (Windows 10:12 / 22/15) seemed to put the printer in the "printer error state", when you try to print a simple document. It has been my default printer for a long time. I followed the suggestions of printer "windows 10", that is, unplug and plug - check cable (not USB) connections, remove the printer from the list of print devices /, reinstall drivers HP for Windows 10 (following suggestions from HP on HP site) - nothing seems to work. It has a network cable connection, but it is directly connected to my computer, no other computers are connected. See screen capture below. I even did a "recovery" of before 12/22! Any suggestions? Thank you. GM

  I received instructions from Microsoft:

  You run the printer Troubleshooter and identify the cause?

  If this isn't the case, we will do that by visiting the link below and see if it helps.

  http://Windows.Microsoft.com/en-us/Windows-10/fix-printer-problems

  Check also the update (KB number) has recently been installed on your computer.

  You can also restore printer drivers and check.

  To restore the driver, you can follow the steps below:

  • Press Windows + R on the desktop screen.
  • Type devmgmt.msc and press ENTER.
  • Expand the printer drivers and do a right-click on the driver and select Properties.
  • Go to the driver tab and click driver RollBack.

  Can I assume that you use a parallel cable to connect the printer to the computer.  If you do this is a known problem that can be solved.  Go to Device Manager and then click ports.  Double-click the lpt for the printer port, and then click on device settings at the top.  Change the default setting of the middle box checked in the box below to use any available interruption. I would also check the legacy down.  If necessary, turn the computer off and then turn it back on, but most of the time this solves the problem without a reboot.

• I try to install my printer HP photosmart series C4500 it error please advice

  I try to install my printer HP photosmart series C4500 it error please advice

  I try to install my printer HP photosmart series C4500 it error please advice

• My computer need to connect to my printer HP 4300 series

  I downloaded successfully, one older, scanner, photocopier, printer, fax printer,

  4300 series, astually called HP Officejet 4315, All in One

  My laptop have accepted it, but I can't print a test page.

  Can you or anyone place the problem... Printing I've done pretty good so far.

  The printer has just ink in it and a new power cord and adapter.

  so I know this isn't the problem.

  Thank you

  Mickey

  Hello

   
  1 did you receive an error message?
  2. If it works well before?
  3. don't you make changes before the show?
  Method 1:
  You try to install the latest printer drivers, software and check:
  Check out the link:
  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?cc=us&LC=en&DLC=en&product=1138342
  
  Method 2:
  You can follow the steps provided and check:
  a. right click on computer and select Manage
  b. click on "services and applications", then click on 'services '.
  c. scroll down to "print spooler", right click and select "Properties".
  d. click 'STOP' service, and then click on 'START' service.
  e. start the wizard 'add printer '.
  
  Method 3:
  If the problem persists, you can check the link for problem troubleshooting network printer given.
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-printer-problems
  You can also view add or remove items from the printer using:
  http://Windows.Microsoft.com/en-us/Windows-Vista/add-or-remove-a-printer
  Also, we can see the fix it:

  http://support.Microsoft.com/mats/printing_problems/en-us

• Prevent printing of PDF forms and masking of the useless message boxes.

  I have a PDF form and I need to avoid printing this PDF form, if the fields are empty.

  To change my form, I use Adobe LiveCycle Designer ES3.

  On how can this be done is written here: http://Forms.stefcameron.com/2008/04/13/prevent-printing-PDF-forms-in-Acrobat-8/

  The only thing that I need more than this article - is to remove the cancelled 'Impression' message box.

  So, if anyone knows how, please help me.

  Hello

  the XFA specification does not describe not a way to remove the error message for the item to validate, so it seems to be impossible.

  http://partners.Adobe.com/public/developer/en/XML/xfa_spec_3_3.PDF#page=1340

• My iCloud and shared calendars has stopped working in MS Outlook today.  They worked yesterday.  Now, I get the error message "cannot open this series of records.  The information store cannot be opened?  I tried the fix standard support.

  My iCloud and shared calendars has stopped working in MS Outlook today.  They worked yesterday.  Now, I get the error message "cannot open this series of records.  The information store cannot be opened?  I tried the fix standard support.

  Same thing here.  Looks like Windows did an automatic update during the night, and now nothing iCloud associated work (calendars, contacts, etc.)

  I also noticed that the error message: "could not load file or Assembly ' MOM." Implementation ' or one of its dependencies.  The system cannot find the specified file. "It started after restarting the Windows Update as well.  I imagine that the two are related in the same problem to iCloud.

• an error prevents my photos appears in Windows Live Photo Gallery

  I keep getting a message when I try to open my photos in Windows Live Photo Gallery: 'an error prevents the picture or video is displayed.  Should I uninstall Live Photo Gallery, or is a more easy way to fix this situation?   Thank you

  I keep getting a message when I try to open my photos in Windows Live Photo Gallery: 'an error prevents the picture or video is displayed.  Should I uninstall Live Photo Gallery, or is a more easy way to fix this situation?   Thank you

  =========================================
  No guarantee... but maybe the exclusive database has
  corrupted.

  Read the following article.

  (944221) freezes Windows Live Photo Gallery
  or does not start
  http://support.Microsoft.com/kb/944221/en-us
  (according to version, database can be
  Pictures.PD4, Pictures.pd5 or Pictures.pd6)

  Rename the Pictures.OLD file will force Live Photo
  Gallery to create a new database on the next launch file.

  Know that the gallery will be as it was the first time that you
  open and some metadata and labels may be lost.

• Windows Live Photo Gallery: 'an error prevents the library to save this picture.

  each 4 pictures that I'm saving I get this Windows Live message Photo Gallery: ' an error prevents the library to save this picture, I just save it again it works but his frustration.

  Hello

  The question you have posted is related to Windows Live, and would be better suited in the Windows Live forum. Please visit the link below to find a community that will provide the support you want. http://windowslivehelp.com/

• I want to add a printer, but get the error message "print spooler service does not work."

  I can't print from my computer.  This has happened with no other visible defects on the computer or the printer.

  When I use the printer in case of problem, and hit the 'add printer' link, I get the error message "print spooler service is not."

  "I did a search on"print spooler"but got no result

  Duane

  Often, but not always, the symptoms you describe are caused by a corrupt print job stuck in the queue or a damaged printer driver.  However before you clean things up, on general principles, that you can download, install, update and run full scans with each of these two free programs:

  AntiMailware MalwareBytes
  SUPERAntiSpyware

  Do not operate the two scans simultaneously.  Each will take a long time, so start it and then go do something else for a while.

  Cleaning of printers

  NOTE: If after completing step has the print spooler is not always running after you launched the command "net start spooler", you will not be able to follow all the steps in "First Article".  Instead, go to the other link and download and get and use the utility 'cleanspl' such as described here.

  If the suggestions below do not resolve your problem, after back and don't forget to include the following information:

  • The version of Windows you have, including service pack (start > run > winver > OK)
  • The brand and model of printer you have (includes the manufacturer, model and model number, as in HP Deskjet 6800)
  • How the printer is connected to the computer (parallel, USB, network, wireless, etc.).
  • It happened just before this symptom started
  • What application antivirus you have and if your subscription is up to date and has been maintained continuously
  • The full text of the error messages related to printing, without paraphrasing

  
  

  A. Clean on print jobs pending

  • Open a command prompt window (start > run > cmd > OK)
  • Type the following in the black command prompt window, and then press ENTER after each line

  net stop spooler
  del/q '% windir%\system32\spool\PRINTERS\*.* '.
  net start spooler
  output

  B. clean the old printer drivers and install the latest drivers by using the directions in One Article.  If you have (or had) a Lexmark printer, follow the instructions on the following site before installing the new drivers, as explained in its first Article: http://members.shaw.ca/bsanders/CleanPrinterDrivers.htm

• HP psc1315 suddenly gives me an error "check print cartridge".

  My HP PSC 1315 worked very well.  All of a sudden the error "Check print cartridge" light.  Nothing will be printed, I can not clear the error, I tried to clean them and with all the options listed under troubleshooting.  Does anyone have a suggestion? I can't wait to go and buy a new cartridge when it is still functional.

  I do not remember how it was resolved, but he did. I remember that try different cartridges don't get rid of the error. It remains a mysterious phenomenon of the singular. However, since this event, when I change the cartridges, the printer does not automatically print a test for the new route pattern. I followed the manual procedure. The printer still works fine after many years of service. I was afraid of having to replace it and am happy that I don't have. Thanks for your concern.

• C5180 all-in-one cannot clear error "cannot print".

  I replaced the ink but still error ' cannot print replace the following empty ink cartridge to continue printing.

  I can't print how can I clear this

  I uninstalled the software and reinstalled still cannot print

  Help, please

  I found the solution

  Unplug the power cord

  2, press OK and help

  3. plug the power cord still OK and help

  4. while still holding OK and help to wait for the screen on the printer to go black

  5. turn on the power button / stop

  This should reset the printer

• Problem area: windows update; Error: TRUST_E_NOSIGNATURE (0x800b0100) __Message: installation error prevented the service pack 2 windows systems (KB948465) _

  Problem area: windows update; Error: TRUST_E_NOSIGNATURE (0x800b0100)
  Message: Installation error prevented the service pack 2 windows systems (KB948465)

  http://support.Microsoft.com/kb/956702

  «Error message when you try to use Microsoft Update or Windows Update Web sites to install updates: «0x800B0100»»

  Method for Windows Vista or Windows Server 2008 to resolve this issue, run the tool (Checksur.exe) system update. To do this, follow these steps:

  1. Download and run the system update tool. This tool runs an ad hoc analysis of inconsistencies that might prevent future maintenance operations. For more information about how to download and run the Checksur.exe tool, click on the number below to view the article in the Microsoft Knowledge Base:
     947821 (http://support.microsoft.com/kb/947821/) Description of the update readiness tool for Windows Vista system
  2. Try to install updates again.

  http://support.Microsoft.com/kb/947821/

  "Description of the preparation tool system update for Windows Vista for Windows Server 2008 and for Windows 7"

  If the above solves the problem:

  It comes with Vista, upgrade install and activate Forum.

  You will get the best help for any problem of Update/Service Pack update Vista Forum; the link below:

  http://social.answers.Microsoft.com/forums/en-us/vistawu/threads

  When you repost here, kindly include this error Code, and exactly what is happening when you try to update.

  In this way, you will receive the best help.

  See you soon.

  Mick Murphy - Microsoft partner

• HP dm1 4000 series keyboards

  Hi, I bought the HP dm1-4310nr U.S. netbook and are having a problem.

  As you know WE use different keyboard configuration that we have here in Europe.

  I was hoping to replace my pc keyboard by purchasing the Northern version of ebay.

  Only flaw is that it is not any version of this keyboard model says in the market if.

  Some other 4000-series keyboard is compatible with it?

  Hello

  There are many keyboards for dm1 machines, they are the same SIZE with yours, but as mentioned on my first answer: you have bought a very special, not available on other markets so same size but may not work. For the keyboard from another supplier, sorry I don't know.

  Good luck.

• Get the comment, "an error prevents photo library to save this image.

  I tried to edit my photos in Windows Photo Gallery and it used to work until about a month.  I always and only used the Photo Gallery program, but now it won't let me to save my changes that I make to photos.  I get the comment, "an error prevents photo library to save this image.  I have read many of the questions that are similar and have done the following...

  1. click on the round of departure
     
  2 type folder options in the search box, and then click the program folder Options
     
  3. Select the view tab
     
  4. in the window of advanced settings, under hidden files and folders, select Show files and folders
     
  5. click on OK
    
  6. go to the following folder (% of user is the name of the account that has the problem):

  C:\Users\%User%\AppData\Local\Microsoft\Windows Photo Gallery

  7. copy all the files here to another location, as a back up and then delete them from the directory of the Windows Photo Gallery

  Once the files are deleted, try to start Windows Photo Gallery.

  After that, go back to folder options and select do not show the hidden files and folders

  This does not work and I don't know what else to do.  Could someone help me please!

  Thank you
  Scarlet

  I tried to edit my photos in Windows Photo Gallery and it used to work until about a month.  I always and only used the Photo Gallery program, but now it won't let me to save my changes that I make to photos.  I get the comment, "an error prevents photo library to save this image.  I have read many of the questions that are similar and have done the following...

  1. click on the round of departure
     
  2 type folder options in the search box, and then click the program folder Options
     
  3. Select the view tab
     
  4. in the window of advanced settings, under hidden files and folders, select Show files and folders
     
  5. click on OK
    
  6. go to the following folder (% of user is the name of the account that has the problem):

  C:\Users\%User%\AppData\Local\Microsoft\Windows Photo Gallery

  7. copy all the files here to another location, as a back up and then delete them from the directory of the Windows Photo Gallery

  Once the files are deleted, try to start Windows Photo Gallery.

  After that, go back to folder options and select do not show the hidden files and folders

  This does not work and I don't know what else to do.  Could someone help me please!

  Thank you
  Scarlet

  ==============================
  Here's what I have on the subject... maybe a
  suggestions will work for you...

  Good luck...

  Windows Photo Gallery...
  Cannot save modified photos...
  possible solutions...

  --

  (1) I saw reports that this problem may be related
  Kodak Easy Share software. Installation "Kodak
  Single-action Version 8 for Windows from the
  the following link may be the solution.

  Kodak Easy Share 8 software version
  http://www.kodak.com/eknec/PageQuerier.jhtml?PQ-path=130&PQ-locale=en_US&_requestid=5320
  (FWIW, it's a good idea to create a system)
  restore point before installing software or updates)

  --

  (2) I've seen reports that could clarify the next steps
  until the question... Right click the library icon and
  Choose "Run as Administrator".

  --

  (3) I copied the info from a tech forum on
  the net... I don't know if it works, but maybe it's
  worth a try:

  A. right click on Task Manager open the
  taskbar on the bottom of your screen and choosing
  The task in the menu Manager.

  B. click the tab process, along the upper part of the
  The Task Manager screen.

  C. in the process tab, select the corresponding button at the bottom
  left of the screen that says "show processes of.
  all users"and click on it. Click 'Continue' to the UAC
  the prompt that appears.

  D. the screen should turns off a moment, then
  back with much more than process listed. Click
  the "Command line" column to sort the list and
  Search:

  "C:\Program Files\Windows Media Player\wmpnetwk.exe"

  Read the description in the next section on:

  Windows Media Sharing Service reader network

  F. click on this process. Click the end «»
  Treat button"at the bottom right of the screen.
  Confirm 'End process' if necessary.

  You should now be able to save your changes to
  your photos normally. The bad news is that this
  should be performed whenever you start or restart Vista.
  And I don't know how to prevent the situation from
  in the first place of loading.

  --

  4) published by: artologik
  The solution came to me when I could not recreate
  the problem on a laptop with Vista Home.
  Everything I could compare, I noticed that the
  %Path% environment variable was not between different
  the 2 machines.

  I guess that WLPG relies on the dll must be found
  on the way to the system; When not found, it must return
  Back to ' base or incomplete "library finds it
  the default specific paths or the user. The solution for
  me has been to ensure the entire path system
  to the folders in the order appropriate.

  To fix, follow these steps:

  A. right click on the COMPUTER icon on the
  desktop and choose PROPERTIES

  B. choose ADVANCED SYSTEM SETTINGS

  C. Si you are prompted by UAC to allow, go ahead.
  and ALLOW

  D. click on ENVIRONMENT VARIABLES...

  E. in the bottom half, under SYSTEM VARIABLES,.
  Find the PATH variable and highlight the

  F. click the button CHANGE

  G. ensure that what starts with
  % SystemRoot%\system32;%SystemRoot%;

  H. ensure you that a semicolon separates each entry.

  I. click OK three times

  J. restart the computer

  K. and here.
  John Inzer - MS - MVP - digital media experience

• Problem with windows vista, suddenly not to recognize a printer HP 5600 series that was printing correctly for 5 years

  Windows Vista Plug ' n Play does not recognize printer HP 5600 series. HP Solutions Center's says no HP devices detected. Using USP connect since the printer 5 years ago. Reinstalling drivers does not help. Installation with disc says printer is not connected (USB) to the computer, who she really is. Have tried all USB ports on the computer to see if plug ' n play would work. Any help in doing so. How can I solve this problem?

  Hello

  Uninstall and reinstall your printer by using the drivers and information on the HP website.

  Equip your model number of the printer for this information and troubleshooting for her.

  http://WWW8.HP.com/us/en/support-drivers.html

  Or ask in the Forums of HP's Support.

  http://h30434.www3.HP.com/PSG/

  See you soon.