Error: "Signal out of range".

Similar Questions

• clean install of windows XP to input signal out of range

  Hi I recently took my old pc xp out of the dusty closet.
  I discovered that the operating system has been corrupted then decided to do a clean install of windows xp.
  However after that it says press any key to boot from the disk and I press a button, then it went to a screen blank and says on the monitor says "Input Signal out of range at 1280 x 1024 60hrz. change."
  I also did a reset factory monitor and hooked up the old pc to the tv.
  So I would like to know how to solve the problem, any help would be much appreciated.

  Hello

  First you using a discrete graphics card or graphics are integrated with the motherboard? Change BIOS battery (or whatever it is in the BIOS change to any method) will not change anything to do with a graphics card discrete and not likley to do much for either integrated graphics card.

  What it sounds like to me, is that the key to the race to start from the CD is not recognized and that Windows is actually booting from the hard drive with a resolution taken not supported by your monitor. But, being not there, I can't be sure of this so here are some ideas of diagnostic.

  Start the PC without the CD inserted, do you have the same problem?

  The keyboard is correctly connected?

  If a PS/2 keyboard is it plugged into the outlet of PS/2 mouse by mistake (keyboard taken are normally purple, green mouse normally Sockets)?

  Is the keyboard PS/2 or USB? You can try another keyboard ideally with the other type of interface?

  You can get in the setup of the BIOS by the appropriate key combination (usually F2 or DEL but I saw others also, look for the message at startup upwards)? If you can not it would indicate a keyboard problem.

  If you can remove the keyboard as a problem, I would return to my original question on a discrete graphics card. If there is a discreet graphics card, the motherboard is also a graphic? If this is the case, remove the discrete card and try windows set up again. Or even try installing windows with a spare graphics card if you can get your hands on one. Turn off the computer and unplug it from the socket before to remove/replace all internal components.

  Finally, what of the installation CD? Is this the one supplied with the PC? It is the recovery of the real manufacturer CD or CD from Microsoft genuine?

  Tricky

• Error "Index out of range" on search query

  I have a configuration of search query to clear my listview and insert new results of the query in the listview. The code looks like this:

  {OnDataLoaded}

  _APP. Clearlist

  root. ListView.insertlist (Data)

  }

  {OnQueryChanged}

  Load();

  }

  But unfortunately, whenever I do a query, and as a result appears my query update (triggered from a contextual menu) does not work and gives me the error "Index out of range". Even if the results of the query to fill listview very well and when I tap on a result it shows all data fine as well.

  And FYI the update query does not work when the list is not be searched or filtered so I don't think that there is a problem with my function.

  What I am doing wrong?

  He solved.  The problem is that the update function trying to remove and add the updated item within the filtered datamodel causing problems.  I just got the datamodel to load before performing the functions as described below:

  bool App::updateObject(const QString &id, const QString &name, const QString &description, const QString &datefield, const QString &lat, const QString &lon, const QString &categoryfield, const QString &mapurl, const QString &itempic)
  {
      bool updated = false;
      bool saved = false;
  
  //    if (!validateID(id))
  //        return false;
  
      Location *location = new Location(id, name, description, datefield, lat, lon, categoryfield, mapurl, itempic);
  
      // Find location in the datamodel.
      // Only the id is used by find(). This is because location
      // defines equality (==) as having the same id. (See the definition of "=="
      // in the location class.)
      const QVariantList updateIndexPath = m_dataModel->find(location);
  
      // update the item if found
      if (updateIndexPath.isEmpty()) {
          alert(tr("Object ID not found."));
          updated = false;
      } else {
          load();
          updated = m_dataModel->updateItem(updateIndexPath, location);
      }
  
      // Save the datamodel if we updated something.
      if (updated) {
          m_storage->deleteFromDB(id);
          saved = m_storage->save(m_lastCustomerID, m_dataModel);
          load();
          refreshGroup();
  
      }
  
      return (updated && saved);
  }
  

• New monitor displays an Error Message "Signal out of range" when computer starts

  Installed new ASUS VS24H-P control on my computer and I get this image of "out of range" bouncing around the corners of the screen.

  This means that the computer sends a signal that the monitor is not capable of displaying.  It could be:

  • A screen resolution (width x height pixel size) is selected, the monitor cannot display
  • The refresh rate (Hz) is the one who can not display the monitor
  • These two

  If you have another monitor, you can plug it to visit your office. Right-click and choose the resolution of the screen, then turn it down to a 'safe' resolution like 1024 x 768 (most monitors can display this).  Then plug your new monitor back and turn the resolution back to a better suited for this monitor.

• HP 2509 b monitor guard displaying "Input Signal Out of Range" and then go to sleep.

  I went on vacation and shutdown my computer for 2 weeks.  My monitor worked great for a month before.  I came home last night and turned on my system this morning.  Now I get a white message in the middle of the screen with "input out of range Signal. Change the settings for 1920 x 1080 at 60 Hz"and then the screen goes to sleep.  I can turn the monitor off, wait a moment and then turn it back on again, but continues to repeat the same thing.  I checked and the screen is already set to 1920 x 1080 at 60 Hz.  I use VGA and have the default positioned like this.  I followed the guide to troubleshooting online for this error, but it did not help.  Can someone tell me please how to fix this?

  Finally, I got this figured out!  Here's what I did.

  Control Panel

  Display

  Parameters

  Advanced

  Intel(r) Graphics Media Accelerator Driver

  Graphics properties

  Display settings

  Expansion of the display

  Chosen at this stage full screen (no border) instead of "maintain proportions"

  As soon as I put this the error screen disappeared!  Can someone explain to me why this adjustment has been around?  I would like to know.

  Thank you all for your help.

• Monitors flicker and "Input Signal Out of Range"

  Hello!

  I have a Mac Mini (end 2012) 2.3 GHz Intel core i7 running up-to-date El Capitan, with two HP monitors 2071d.

  These monitors have DVI connections. It is connected with Mini DisplayPort to DVI adapter, and the other with HDMI to DVI adapter (provided with the Mac Mini).

  Everything has been fine for a year until this week. Two monitors are:

  (1) intermitantly began flickering of the scrambled images

  (2) flickering intermittently at black or white noise

  (3) intermittently flickering white noise

  (4) the message of the form 'input out of range Signal. 1600 x 900 at 60 Hz settings."

  How is this problem go and come, but rather continues today.

  After research, I tried to start safe mode, but the problem persists.

  I read that put the computer to sleep and then wake up could solve this problem... it worked a

  couple of times, but the issue soon returned.

  I tried to reset several times VRAM/LANDAU and SMC.

  I doubled checked all the connections.

  Under the system of preferences > display (when the image is stable long enough for me to see) everything looks OK. Under the screen of the 'Default display' tab is selected. On the color tab, there are three HP2071d listed (with a selected) in the window display profiles. I've linked by selecting one of the other "HP2071d" listed without noticeable change.

  I also reset both monitors to factory settings via the menu screen of the monitors.

  I also came across this mini Mac EFI Firmware Update 1.7 for flickering on end of 2012 Mac Minis, but when I tried to run I got "this software don't is not supported on your system. Ugh. It turns out that my Mac Mini is already updated to MM61.0106.B0A (2015-002)

  My Information System > Hardware > graphics/display info is:

  Graphics Intel HD 4000:

  Chipset model: Intel HD Graphics 4000

  Type: GPU

  Bus: integrated

  VRAM (dynamic, Max): 1536 MB

  Seller: Intel (0 x 8086)

  Device ID: 0 x 0166

  Revision ID: 0 x 0009

  Exhibition:

  HP W2071d:

  Resolution: 1600 x 900 at 60 Hz

  Per pixel: 32-bit color (ARGB8888)

  Display serial number: 6CM3171PFF

  Mirror: on

  State of the mirror: mirror material

  Online: Yes

  Rotation: support

  HP W2071d:

  Resolution: 1600 x 900 at 60 Hz

  Per pixel: 32-bit color (ARGB8888)

  Display serial number: 6CM3170P31

  Main screen: Yes

  Mirror: on

  State of the mirror: mirror of Master

  Online: Yes

  Rotation: support

  I am of the ideas of what else to check/try.

  Thanks for any assistance that anyone can provide.

  bdcs64 wrote:

  Hello!

  I have a Mac Mini (end 2012) 2.3 GHz Intel core i7 running up-to-date El Capitan, with two HP monitors 2071d.

  These monitors have DVI connections. It is connected with Mini DisplayPort to DVI adapter, and the other with HDMI to DVI adapter (provided with the Mac Mini).

  Quite the same configuration except here, with 2 Samsung S22B310 DVI monitors on an i5 2.5 GHz in late 2012.

  Everything has been fine for a year until this week. Two monitors are:

  (1) intermitantly began flickering of the scrambled images

  (2) flickering intermittently at black or white noise

  (3) intermittently flickering white noise

  (4) the message of the form 'input out of range Signal. 1600 x 900 at 60 Hz settings."

  How is this problem go and come, but rather continues today.

  Both monitors isn't good. Which would lead us to think that the Intel HD 4000 is overheating and the problem is not with any of the adapters or cables. Although, if one of the cards was not internally, it could put additional heat stress on the graphics chip.

  Personally, I will try a few things.

  1. turn off, unplug everything, open the bottom cover and give it a good cleaning to make sure it cools properly.

  https://www.iFixit.com/device/Mac_Mini_Late_2012

  2. try each monitor individually for awhile configurations see if the problem follows the monitor cable adapter installation.

  (I know he'll be a brake after obtaining used monitors to double)

  3. try using > MacFanControl to monitor and help control the temperature of the GPU ITPP.

  http://www.CrystalIDEA.com/Macs-fan-control

  FWIW, I do not use screensavers, but I do a lot of videos as well as some games of light on both my 2010 and 2012 of the Mini and I really believe that MacFanControl has really helped to extend the life of graphics on these two systems.

  I use the control based on the sensors on the sensor of GPU ITPP and configured so that it starts slowly rise in power of the fan above 129' F

  

• Why is there a box in the middle of my screen "Input Signal out of Range"?

  This message box appeared after I restored.

  Hi dalbertt,

  1. Are what food you referring?
  2. How do you restore on the computer?
  3. What is the number and the model of the computer?

  Method 1

  I suggest that you try to change the resolution of the screen and check if it helps.

  Change the resolution of your monitor

  http://Windows.Microsoft.com/en-us/Windows-XP/help/Setup/change-monitor-resolution

  Method 2

  If the previous step fails, then try to start the computer to activate the VGA mode and then try to change the resolution of the screen.

  A description of the options to start in Windows XP Mode

  http://support.Microsoft.com/kb/315222

• Error, input signal is out of range on installing Windows 7

  Hello again, I install Windows 7 on my computer of mothers, but when installing, restart the computer, the screen does not work it says input signal out of range can be dis is because the video card is not a driver, we have a disk with driver say but. Help thanks for all this

  I want to thank you to you all. I solved the problem, I just connect the PC to the TV via a cable VGA windows starts normally and I go to control panel and then to the system and security, then the administrator tools, then the configuration system. When the system configuration window opens I go to the page "boot" and click on "basic video" and then apply the settings and then click on "ok" and I restart the computer. When the computer restarts I unplug the TV and plugged VGA on the monitor cable. I expect windows to load and load successfully when all was fine with the monitor. I change the screen resolution to the highest that my monitor supports. And now everything is fine. Thank you.

• Monitor "Signle Out Of Range" error?

  Hello

  I currently have two monitors Setup. The principal is a 20.1 "(également assez nouveau) and works very well, however, my 2nd monitor (old CRT 19"), decided the next day he does not want to work more. " He has the power, is linked up to my PC correctly, and I did nothing out of the ordinary recently. The problem is that I start my PC and everything it says on the 2nd monitor is 'Signle Out Of Range', and none of the controls on the monitor itself no longer works. I tried switching autour monitors to see if it works as a main monitor, but without success. Windows does not seem to think that something is wrong with her, any more than my graphics card.

  Windows 7 Ultimate 64 bit

  NVidia GeForce 9800 GTX GPU 512 MB of video memory

  The system does not think that something is not at all I can say... can someone help me to try to find a solution or does it just sound like my last CRT monitor is eventually died?

  Thank you

  Ricky

  All the information you presented suggests the monitor CRT is close to death. The switch that you did onscreen main task, without success, shows the connection of the cable, the port of graphic adapter and the details of the parameters are not the problem - the monitor is the problem. "Signal out of range" warning could mean several things, but statistically, it means the refresh frequency is zero, i.e. internally the horizontal sync signal is not present.

  Display systems these high voltage (CRT) just "upwards and die", it is their behavior that is proven. So my advice is to plan a funeral and go shopping for a new monitor. Yes, patients out even of long comas, but I wouldn't bet on a surprising outcome.

  My condolences,

  Paulo

• randomly out of range?

  I have a hp 6200 pro, core i3

  I have the computer attached to a 42 "sanyo lcd tv, the picture is superb, but from time to time when the resumption of the fashion watch, I'll get a pc off error, reset the pc to sleep corrects most of the time there.

  I would like to know how to solve this problem, because it is a little distracting.

  current setting is @60 1920 x 1080 p hz

  Hello

  It may be possible that the video adapter to update the screen setting is incompatible with your new monitor. I'll be you providing an article that has a possible resolution to your question.

  New monitor shows garbled display or an Error Message "Signal out of range" when computer starts

  Let us know if it helps.

• input out of range with HDMI to VGA LE1901w

  Hello!

  Recently, I acquired a LE1901w monitor as a second screen. I'm trying to connect it to my Toshiba u925 using adapters HDMI / VGA (because neither the monitor has an HDMI port, or the laptop has a VGA output).

  I get the message "input out of range signal" requesting a change to 1440 x 920 @ 60 Hz and continues to display until the monitor going to sleep even when I change the settings according to demand.

  I have an integrated Intel HD Graphics 4000 and I use the default Windows for Windows 8.1 monitor drivers

  Any comments will be useful

  Thank you

  Hello @fbinim,

  I understand that you get the message "Input Signal Out Of Range" and it asks you to change at 1440 x 920 @ 60 Hz. I suspect it's a driver problem and you need to make sure that your drivers are up to date on your computer. Just to be safe, I recommend if you could to move the HP LE1901W monitor to another computer and make sure you do not have the problem. If you have it on a different computer the problem you are experiencing seems to be a physical problem. Please contact our technical support at the 800-474-6836. If you do not live in the United States / Canada region, please click the link below to get help from your region number. http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html.

  I want to thank you for display on the HP Forums. Have a great day!

• "out of range" error on I-110 fieldpoint

  We try to connect the pressure Omegadyne transducers (PX1004L1) that give a reading of mV to 10 v excitation. Before you connect the 4 cables (excitation, signal and two Commons) I-110, we get an error 'out of range '. Disconnect the signal + / leads and measure with a multimeter, we read the mV expected signal. If reconnect us the signal + / conduit and disconnect the excitement + / leads and then connect to a power source (external to the I-110), we read the expected of the I-110 mV signal. Any suggestions on what is happening here? We have already exchanged the head I-110 with a spare part that we know is operational.

  I have not heard of "Omegadyne", but I know Omega.  What is the device?  http://www.Omega.com/pressure/PDF/PX1004.PDF

  You're talking about 2 Commons.  But what I see, it's a bridge 4 circuit son strain gage.  I think you should use a SG-140 module to read this device.

• "Error 0xBFF69012 attribute value is out of range" for Point Grey Grasshopper2 GS2-GE-50S5M

  Try to get the camera above to work at MAX. Running on LabView 2010 SP1 with Vision Acquisition software August 2010.

  Errors illustrated: error 0xBFF69012 attribute value is out of range

  Camera works perfectly well on the supplied software advanced Grey. Point Grey Image Filter Driver installed. Turned off the Windows Firewall. Card (http://www.sonnettech.com/product/prestogigproec34.html) Ethernet supports Jumbo Frame.

  Read through the following measures without result:

  http://digital.NI.com/public.nsf/allkb/FCE7506A3AF7636C862576240072716D

  http://digital.NI.com/public.nsf/allkb/A0A1CE4704265BF2862578CA007A4CF8

  How will I know if there is a problem with the XML file?

  What are the possibilities that this device is not compatible with IMAQdx?

  Thank you.

  Problem solved in new firmware version 1.25.3 - 00.

  Contact Gray Point to this firmware.

• The IVI Drivers: RangeCheck of initialization option set to true: failed to get an out-of-range error

  Hello

  I'm new to IVI drivers (started using them last week) and I have a problem with the option of initializing RangeCheck.

  So get used to the IVI drivers, I used the example provided with the AgilentE36xx IVI - COM driver (on my computer, it is located in C:\Program Files\IVI Foundation\IVI\Drivers\AgE36xx\Examples\VS.NET\Cpp\Example1).

  I could do everything I wanted except get an error out-of-range, during the passage of an out-of-range value to a function. I put the RangeCheck init option to true, but I don't have any error in the simulation, nor with the connected equipment.

  Attached is the code (from the example of Agilent) but modified so that it should throw an out-of-range error when adjusting the tension on the following line: spOutput1-> VoltageLevel = 1000; ... why no error.

  Still, it runs correctly. Can someone tell me what I'm not doing correctly.

  Kind regards

  Roman

  Hello

  I posted the question on the Forum of Agilent.

  Here is the link to the post: http://www.home.agilent.com/owc_discussions/thread.jspa?threadID=33348&tstart=0

  The problem is now resolved. Thank you for your help.

  Kind regards

  Roman

• I am facing a problem with the beep.vi. I have a DAQ program, which acquired the signal and compare it to a threshold value. When a signal is out of range, a Visual and sound alarm has occurred. I use the VI beep.vi to generate the sound.

  I am facing a problem with the beep.vi.  I have a DAQ program, which acquired the signal and compare it to a threshold value. When a signal is out of range, a Visual and sound alarm has occurred. I use the VI beep.vi to generate the sound. Everything works fine except the sound alarm. It gives the table 1 d of type mismatch. I tried to fix this by placing it in a box structure. But it still does not work. If someone could help? Please find attached my VI. Best wishes to all visitors to the Forums of Discussion OR.

  Ihab El-Sayed

  published here: http://forums.ni.com/t5/LabVIEW/Playing-sound-based-on-exceeding-a-threshold-value-1D-array-data/m-p...