Error starting system Acer Iconia W500

Similar Questions

• Acer Iconia W500

  My wife uses a Tablet Acer Iconia W500.  It has limited the view.  Is there a "Speaking keyboard" function with this Tablet?

  Yes, the W500 is a Windows Tablet, so the Narrator is what you are looking for.

• Error in partition Acer Iconia B1 does not accept the update.

  My new Acer iconia b1 - a71 16 GB does not accept the OTA update in the system start menu! He accepts, and download the update. After that is give me to reboot and install. And after - installation under the start menu in the system stops

  ERROR:-invalid partition setting
  17: 238e8000:888e8000 of fat
  Instalation aborted.

  The Tablet is clean and the. I tested it without SD card inside. I even try with the original OS rom in the Acer support site - and still the same error! Can anyone describe it is hardware problem to return to the supplayer or how to fix this problem?
  Can you help me?

  A hotfix is available to resolve the error of invalid Partition. In addition, we have created a few video tutorials that will help guide you through the installation of the patch.

  Download the patch

  Iconia B1 - A71, install the USB 2.0 driver - video tutorial

  Iconia B1 - A71 error invalid when updating Android (FAST) partition - video tutorial

  Iconia B1 - A71 error invalid when updating Android (FULL) partition - video tutorial

• Error starting system (my system boot is mistake...).

  invalid product information

  the following product information programmed into the system wide

  is missing or invalid

  Hi @RAMKUTTI ,

  Thank you for visiting the Forums HP's Support and welcome. I read on your HP laptop and get a system error or a black screen at startup. Try perform a reset.

  When you perform a hard reset note remove all USB devices. Disconnect all non-essential devices.

  Here is a link to computer does not start for Windows 7.

  If this does not help at the end of the document it tells you to do a test equipment.

  You can Reset the BIOS with this document by selecting Reload the default BIOS settings. Helping others because it restores the default settings and resets the system.

  I hope this helps.

  Thank you.

• No Wifi Iconia W500 with windows 10

  Hello

  I upgraded my Acer Iconia W500 from Windows 7 to Windows 10 own factory.  I made sure that I have ALL the updates from Microsoft.  Everything works great EXCEPT that I can't get Wifi to turn on.  The button to activate the Wi - Fi is grayed out. Airplane mode is NOT on.  If I go to the network settings, the slider for Wi - Fi is disabled and when I pass it on it just turns right back to the off position.  I've updated the driver Wifi for the latest driver, I could find which is Qualcomm Athereros Communications 3.0.2.181 with a driver date 12/03/2015.  I tried uninstalling the driver and the device several times and allow Windows to find the adapter again.  Whenever he recognizes the right device and installs the driver.  I even looked in the bios to see if the wireless adapter has been disabled, but it is not yet a Wifi option in there.  I tried to uncheck the 'allow the computer to turn off this device to save power"option in the properties of the adapter, but it doesn't help.  I don't see any errors in the event viewer (or anywhere else).  I can use the LAN adapter very well, but it doesn't make it very portable if I can't use Wifi.  Someone at - it ideas?

  Thanks for your help!

  Hey there! Recently, I had this same problem on my Acer One 10 series. I've been frustrated with it for about two weeks! What had to happen, it is that the driver used to connect to wireless networks do not automatically update to a version compatible with Windows 10. In order to download the correct version, the only answers that I could find were to go to the manufacturers Web site and download a driver from there. The problem is that you can't really do that as easily without wifi.

  What I suggest, is to use another computer to go to the Acer site. Click on the tab "store". Then choose your country. On the next page, scroll down to the bottom, under 'support', there is a link that says "driver downloads".

  From there, enter or search for your model. Once you have selected your model, below there will be a list of driver downloads, you might need. The one you want is 'Wireless LAN'

  Another computer, this download to a flash drive, then download it from the flash drive on the device with the questions. Make sure it is in a real folder, so it does not disappear when you exit the flash drive (obviously).

  Once downloaded, go to the start menu and select settings. Click Update and security, and then resumed. Click restart now under "advanced startup." it will make something akin to restart, do not touch anything until it gives you the option to select "Troubleshoot".

  Once you have selected troubleshoot, select 'advanced options', select 'Start settings' then 'restart', it will then take you to a list of options, select the option to disable the signature of driver backup.

  Once you have selected, your device should restart. Once he does, the new driver update should be tactful and you should be able to access the internet.

  It took me two weeks to understand this, all this, but the process that I wrote for you probably takes less than an hour and it actually worked.

  I know that it is a batch, but it worked for me, and I hope it works for you! Good luck!

• Iconia w500 reset stuck at "Create an account for this PC" during windows install only mouse works

  I have the Acer Iconia W500 we have upgraded to Windows 10.  Due to the assumption of updated driver, I decided to reset the tablet.  I have reset the system without discs and then installing Windows, that the computer is blocked "create an account for this PC' because the USB mouse works.  I discovered that the touch screen and a keyboard are unusable during this process so I plugged a USB mouse that works very well.  But installing requires that I type a user name, and it won't let me skip this step.  Without keyboard or touch screen, I am unable to enter a user name in the field.  Thank you for your suggestions.

  Plug a keyboard instead of a mouse, you can tab between fields to be able to live without the mouse. If you do not have a practical USB keyboard, check the local thrift stores. They are generally very cheap there...

• Acer iconia a b3 - a30 errors after the system update

  Hi my Tablet conducted an update of the system. Everything is fine, but now I get errors for the portal app Acer and Opera app unexpected error please reboot if I restart the app it crashes again.

  Also is it possible to change ro_debuggable to 1, so I can use root adb shell thank you

  Robb

  Hi Robb,

  In regards to the error continues to Acer portal on your Acer device, I suggest that you can try to uninstall Acer Portal updates and reinstall by downloading the Acer Android portal according to its online help.

  If the problem persists, I will really appreciate if you could provide us with more information below. Thank you!

  1. Please send your comments via the portal Acer Acer BYOC applications support.
  
  
  2. Please capture that a screenshot of the error message occurs on the Acer site and we send it to the best solution.

  Acer BYOC Apps support

• I tried to update OSX 10.5.6 to leopard 10.6.3 and was not working due to a disk error but now my mac book does not, as the starting system, but after a few secons it will turn off itself, what should I do? Thank you very much!

  I tried to update OSX 10.5.6 to leopard 10.6.3 and was not working due to a disk error but now my mac book does not, as the starting system, but after a few secons it will turn off itself, what should I do? Thank you very much!

  You probably should have updated to 10.5.8 first.

  Installation or update of Snow Leopard:

  http://manuals.info.Apple.com/en_US/Snow_Leopard_Installation_Instructions.PDF

• When you try to install Windows Defender I get an error message "Service"Windows Defender"(WINDEFEND) could start. Make sure you have sufficient privileges to start system services.

  Original title: could not start the Service "Windows Defender" (WINDEFEND)

  When you try to install Windows Defender, I get an error message that

  "Service"Windows Defender"(WINDEFEND) was able to start. Make sure you have sufficient privileges to start system services.

  How can I check which privileges I have and I need?

  I noticed in the management of the tasks that Norton symlcsvc.exe ran and I was wondering if it was who collide with the Defender, so I temporarily stopped Symantec process running in the field of Services, but still had the same result, try to run the installation of the Defender.

  Help please

  Hello

  This error message is because you have Norton installed on the computer. See the for more information section below.
  http://www.Symantec.com/business/support/index?page=content&ID=TECH103119&locale=en_US

  Let's try the steps and check them off below if it helps.

  Step 1: You can try to uninstall Norton and then check if the problem persists.
  Note: Reinstall Norton after verification.
  Reference: http://support.microsoft.com/kb/307895

  Step 2: Change the registry value and check.

  a. Click Start, type regedit.exe and press ENTER.
  b. navigate to the following location: HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows Defender\
  c. right-click on DisableAntiSpyware, on the right panel, then selectEdit.
  d. enter 0, under value data, and click on the OK button.
  e. close the registry editor.
  f. restart the computer.

  Registry warning:
  Important this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  How to back up and restore the registry in Windows: http://support.microsoft.com/kb/322756

  Thanks and greetings
  Umesh P - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  [If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message.] [Marking a post as answer, or relatively useful, you help others find the answer more quickly.]

• What is causing the error event ' BCM42RLY service failed to start due to the following error: the system cannot find the file specified "Event Id 7000

  What is causing the error event ' BCM42RLY service failed to start due to the following error: the system cannot find the file specified "Event Id 7000

  Hello

  1. Since when are you facing this problem?

  2. What is the number of brand and model of the computer?

  3. have you made changes on the computer recently?

  BCM42RLY is a Broadcom network card driver. I suggest that you uninstall and reinstall the drivers and check if it helps.
  Uninstall or reinstall a device: http://technet.microsoft.com/en-us/library/cc725782.aspx

  Hope the information is useful.

• "80070002" error the system cannot find the file specified with start.vbs

  Original title: Windows Script Host

  Script: C:\Program Files\PCDApp\start.vbs

  Line: 2

  Char: 1

  Error: The system cannot find the specified file.

  Code: 80070002

  Source: (null)

  1 first, update your AV program and run a full scan. Then download, install, update and run a full scan with malwarebytes(free). This will help you establish that his little likely to be malware related, or not.

  If each scan find and remove whatever it is, does the problem persists after that scans have completed?

  2 if so, try a clean boot. If the problem does not occur in 'clean boot' then follow the section "How to determine what is causing the problem by performing a clean boot" in an attempt to establish that generated the message.

  Do not leave your PC like the clean boot and return to a normal startup after your investigations.

  3. If the boot doesn't help, take a look at autoruns to see if that can locate which is turned on and generates the message.

• Failed to start Remote Access Connection Manager Service. Get the 20 error: the system cannot find the specified device.

  This seems to have started with the last batch of updates of Windows 7 (including SP1).
  I can't connect using dial-up.  Get the message:
  Cannot load the Remote Access Connection Manager service
  Error 711: The operation could not complete because it could not start the remote access connection manager service
  in time.  Please try the operation again.

  When I try to start the Remote Access Connection Manager service manually, I get the message:
  Windows could not start the service on Local computer remote access connection manager.
  20 error: the system cannot find the specified device.

  My phone displays the modem works properly, and telephony and the Secure Socket Tunneling Protocol service started.

  I don't know what else might have changed.

  Hello Vince_867,

  Thanks for your post.  Take a look at this thread for a possible solution to your problem.

  See you soon

• Windows Live ID Sign in French Wizard error - "Windows Live ID Sign in Assistant (wlidsvc) Service could not be started. Make sure you have sufficient privileges to start system services. "

  I want to install the Windows Live Id sign in assistant.

  But when its almost done I get this message:

  "Windows Live ID Sign in Assistant (wlidsvc) service could not be started. Make sure you have sufficient privileges to start system services. "and the RETRY and CANCEL buttons.

  Can someone please tell me what to do.

  I appriciate it :)

  Hello

  For more specialist help on issue of Windows Live Sign-in Assistant, you can post your request here:

  Windows Live Forum - http://windowslivehelp.com/

• No image with customized image of Windows 10 Acer Iconia W510

  I'm trying machines Acer Iconia W510 image with an image of Windows 10 we did. We have already photographed a few tens of individuals. A dozen, however, refuse to take the picture. They are currently on Windows 8. The image on an external hard drive that plug us into the USB port.

  The steps I take to the imaging process are as follows: "Change PC settings"->"update and recovery"-> "recovery"->"Advanced startup" and I click on the button 'Restart now', who sends me to a screen with three options, continue to windows 8.1, troubleshooting, and turn off your PC.

  I select 'Troubleshoot '->' Advanced'-> "Image system recovery"

  The Acer screen appears with "Preparation of the system image recovery" at the bottom. I sign in the administrator account when prompted to choose an account.

  A window appears and scans for images. I selected the "Select a system image" option and then select the correct image of Windows 10.

  Then, I select the only available option for "select the date and time of the system image to restore.

  After that, there is a message that says "for the restoration of this computer, needs of Windows to format the drive that the Windows recovery environment is running on." To continue with the restore, shut down this computer and it boot from a Windows installation disc or a disc repair system, then try the restore again. "At this point, I have no way to continue.

  Even if I plug the USB recovery drive we used, I get the same message. I don't know what the problem is or how to get past. Any help is appreciated!

  Hi Ryan,

  According to the description, you can not install updates and the this issue may occur if one or more of the following conditions are met: 

  1. The Windows Update database is damaged.
  2. Antivirus software is configured to scan the folder % Windir%\SoftwareDistribution.
  3. Service (BITS) Background Intelligent Transfer Service does not receive a content link header.
  4. A required system file is incorrectly registered.

  Try it out below mentioned methods and see if it works for you.

  Method 1

  First of all, I suggest you run Windows update troubleshooting tool to get the problem automatically detected and corrected. This fixit checks the configuration of the Windows Update components and repairs, fixes incorrect Windows Update the locations of data and records of necessary services. For the race, the troubleshooter refer to sub article what can I do if I have problems to install updates.

  Windows Update: FAQ

  Method 2

  I suggest you to check if you are able to access Windows Update services and also make sure that the following services are started. If it is not started, follow the listed below as follows:

  a. press the Windows key + R, type "services.msc" (without the quotes) in the Run dialog box to start, and press enter.

  b. Locate the Windows Update service.

  c. right-click on the Windows Update service and select Properties.

  d. in Startup type, select enable.

  e. click Start under Service status.

  f. click OK.

  g. Repeat steps c to f for the following services :

  CSP & Background Intelligent Transfer Service.

  If these steps do not help to solve the problem, you can proceed to the step below and check.

  Method 3

  If the problem persists I suggest to reset the Windows Update components and for this, try to run the fixit described in the following article. If you already tried the fixit even before that I ask of you rerun the fixit.

  How to reset the Windows Update components?

  http://support.Microsoft.com/kb/971058/en-us#LetMeFixItMyselfAlways

  Keep us.

  Kind regards

• Read error - SOLUTION system configuration data

  Today, I found a solution to the error of notorious boot not only on the toshiba, but some other brands also.

  The error is: System configuration data read error.
  He invites to start with 2 beeps which prevents the computer laptop Moldavian from.

  I tried everything I could to remve this message but noything helped me.
  Replace all, cmos battery, updated the bios, loader, drives, keyboard and etc.

  Today, I found a solution very simple that I want to share with you guys.
  This solution worked for me and I hope it will work for you too.

  Are you ready? :)

  Go to the Bios and change the Bios language french.

  Post here if it works for you also.

  Thanks for sharing your experience with us. But its really hard to believe that your solution would be linked to all devices such problem

  However, good to know that this small change in the BIOS has helped you to resolve the issue