Error: "unable to start Windows XP" after recent updates

Similar Questions

• I have a dell xps with vista and get the error "unable to start windows.

  I can then choose the launch startup repair or start windows normally.  as soon as I clicked launch startup repair, he says that it is not able to PC repair.  I tried to enter safe mode, it restarts, flashes a blue screen and takes me to start the reboot system again.  I tried to run a recovery from a previous version of my sw windows (via the options in advance in the Startup Repair menu), but this does not solve the problem of boot loop.  I can get to a c prompt, but that's all.  I prefer not to use the dell factory image restore and losing all my files.

  today

  Run dell diagnostics

  http://support.Dell.com/support/topics/global.aspx/support/KCS/document?c=us&CS=19&l=en&s=DHS&docid=DSN_A9E3A15597A04AFBB02EE16785D39C5C&isLegacy=true

  Data recovery

  1. remove the hard drive and it slave in another computer

  2 buy or borrow a USB disk drive hard put in yout case then plug it into another computer and read the hard drive like this

  3. try Knoppix

  http://www.Knopper.NET/Knoppix/index-en.html

  BUT this method 3 depends on your hardware in the computer that failed

• "Unable to start Windows. A recent hardware or software change might be the cause. »

  http://prntscr.com/83io5  (Typed it upward in Notepad on my desk)
  It's the splash screen I receive. I tried all the options unique it says, including the drive installation and repair it. However, when I try to fix it through the disk it evokes just similar picture blue background on the Windows Vista installation disc, but it is not raise one of the interfaces for me fix or repair windows.
  When I try all other options, it is as windows will load, but before that the bar ends or whatever, a blue screen with text flashes on really fast, then disappears without giving.
  The only thing that's happened before this started to happen if it fell off my table which is like 3 feet off the ground. Nothing else and it worked fine after that. I took a NAP, woke up to the top and BAM. He does this.
  Any help please? Thank you.

  Better files so that you can register, it looks like your hard drive is damaged!

• Unable to start Windows 7 after I install Vista in dual boot

  original title: Boot Manager

  I install Windows 7 first before vista

  Vista option swallowing the other OS

  No option of the OSes to choose at boot

  Vista is accessible directly

  Thank you

  An in Windows 7 Startup Repair can solve the problem - give it a try.

  Try to use BCDEdit: http://www.sevenforums.com/tutorials/2676-bcdedit-how-use.html. You can modify the startup files to create a situation of dual boot (make sure that you use the existing boot files - be they on the Vista partition or partition Windows7).

  You can also use bootrec.exe to perform essentially the same thing: http://www.vistax64.com/tutorials/163304-dual-boot-using-free-partitioning-software.html.

  I hope this helps.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Cannot start Windows 7 after the update of the system

  I don't speak of Windows 7 RTM, I know is RC forum but I downloaded the RC of microsoft's official website and I can't install it, it reached the "end of installation"(ou quelque chose comme ça) phase and blue screen of death appears, saying "memory dump" and other things. ". That's why I downloaded RTM from a torrent site, I installed it, everything was fine, the aero was not on so I that I should update the video drivers and then I downloaded all the updates possible (via the control panel), then I restarted the pc and now I am not able to load windows , it's blue screen of death! Notice that I can run windows 7 mode safe mode, but when I try to start it in normal mode the blue screen appears. BTW, I have windows xp installed on my pc as well. So, here is my setup:

  AMD 7750 dual-core 2, 7GHz
  4 GB of RAM, 800 Mhz, but the system says 3.25 alone can be used
  ATI 4730 512 MB, btw I have integrated graphics card (ati hd3200, I think), don't know if it's important but...

  Here is the information about the error:

  Signature of the problem:
  Problem event name: BlueScreen
  The system version: 6.1.7600.2.0.0.256.1
  Locale ID: 1026

  More information about the problem:
  BCCode: 116
  BCP1: 871F13D8
  BCP2: 90C204B4
  BCP3: 00000000
  BCP4: 00000002
  OS version: 6_1_7600
  Service Pack: 0_0
  Product: 256_1

  Files helping to describe the problem:
  F:\Windows\Minidump\080809-15375-01.dmp
  F:\Users\blah\AppData\Local\Temp\WER-22953-0.SysData.XML

  Read our privacy statement online:
    http://go.Microsoft.com/fwlink/?LinkId=104288&clcid=0x0409

  If the online privacy statement is not available, please read our offline privacy statement:
  F:\Windows\system32\en-US\erofflps.txt

  Here's the crash dump:

  Debug version of Microsoft Windows (R) 6.11.0001.404 X 86
  Copyright (c) Microsoft Corporation. All rights reserved.

  Loading dump file [F:\Windows\Minidump\080809-14921-01.dmp]
  The mini kernel dump file: only registers and the trace of the stack are available

  Symbol search path is: * invalid *.
  ****************************************************************************
  * Loading of the symbol may be unreliable without a symbol search path.           *
  * Use .symfix to get the debugger to choose a symbol path.                   *
  * After adjusting your path to symbols, use .reload to refresh the locations of symbols. *
  ****************************************************************************
  Executable search path is:
  *********************************************************************
  * Symbols cannot be loaded because the path is not initialized. *
  *                                                                   *
  * The symbol path can be defined: *.
  * using the _NT_SYMBOL_PATH environment variable.                 *
  * with the help of the there when you start the debugger argument. *.
  * using the .sympath and .sympath + *.
  *********************************************************************
  Cannot load the image \SystemRoot\system32\ntkrnlpa.exe, 0n2 error Win32
  WARNING: Unable to verify timestamp for ntkrnlpa.exe
  ERROR: Module load completed but symbols can be loaded for ntkrnlpa.exe
  Windows 7 Kernel Version 7600 MP (2 processors) free x 86 compatible
  Product: WinNt, suite: TerminalServer SingleUserTS
  By: 7600.16385.x86fre.win7_rtm.090713 - 1255
  Computer name:
  Core = 0 x 82803000 PsLoadedModuleList = 0x8294b810
  The debugging session: 11:50:54.734 Saturday, August 8, 2009 (GMT + 3)
  System Uptime: 0 days 0:00:19.343
  *********************************************************************
  * Symbols cannot be loaded because the path is not initialized. *
  *                                                                   *
  * The symbol path can be defined: *.
  * using the _NT_SYMBOL_PATH environment variable.                 *
  * with the help of the there when you start the debugger argument. *.
  * using the .sympath and .sympath + *.
  *********************************************************************
  Cannot load the image \SystemRoot\system32\ntkrnlpa.exe, 0n2 error Win32
  WARNING: Unable to verify timestamp for ntkrnlpa.exe
  ERROR: Module load completed but symbols can be loaded for ntkrnlpa.exe
  Loading the kernel symbols
  ...............................................................
  ................................................................
  ..........
  Loading user symbols
  Loading unloaded module list
  .....

  Pirated Windows 7 allows malware, botnet zero-day ZDNet.com.url

  Messages rating helps other users

  Mark L. Ferguson MS - MVP

• Cannot start windows more after Microsoft Update

  I have XP.  Once Microsoft installed a auto update July 16, I could no longer open Windows normally.  What did do? That's happened?  How can I return to my computer if can't open?  It seems that the computer doesn't send any signal to the video monitor so I can't enter all orders. Finally, I learned that I can open in Mode safe mode but not in normal mode... But I need a normal mode to access everything.

  Of "automatic update" are what kind you referring?  As you have acknowledged, XP should not be getting updates.  I also asked if you have an installation disc, and you did not.

• Got the error saying that unable to start Windows. Now, it freezes after loading Windows.

  Original title: Windows Recovery Error Question

  Earlier I was looking at my computer, running a virus because my computer scan playing strange earlier. Every time I start Windows, I would be spammed with windows titles 'open with... '. ». I managed to open the Task Manager and get rid of all of them, but my computer shifted significantly again. Whenever I close it and restart the same thing would happen. I opened my virus scanner and started running it. Of course, he had a virus.

  As I was waiting for the analysis at the end, my computer suddenly closed and restarted without any warning at all. It froze on the splash screen. To stop and restart my computer again, I received a message that says:

  "Unable to start Windows. A recent hardware or software change might be the cause. If Windows files have been damaged or misconfigured, Startup Repair can help diagnose and fix the problem. If the power was interrupted during startup, choose Start Windows normally. »

  I was given two options: Launch Startup Repair (recommended) and start Windows normally. When I select the Startup Repair tool, I am taken to a screen with a loading bar that says "Windows is loading files... ». After loading, the screen would freeze. If I try the other option, I am taken to the splash screen and it would freeze.

  Is it possible to fix this? Any help would be greatly appreciated.

  Hello

  I suggest to unplug an external device connected to the computer and then try to start the computer and check if it helps.

  Otherwise I suggest you to contact the computer manufacturer for help.

• The following error during the installation of Windows: "cannot start Windows. A recent hardware or software change might be the cause.

  Help, please! Installing Windows Interrupted!

  Hi recently my computer was giving me a bit of concern for example (running slow, do not easily light etc...). A couple of days, my computer has decided not to put on after a glance on the net (on my other computer), I found I had a problem call KSoD or black screen of death, therefore I went on youtube and made all the different things said youtubers can fix this how ever none of these things worked, so finally I decided that I would have factory reset my computer/windows to using the system restore. However, at half way through the installation of windows after the factory reset (my computer came with no disk Windows), my computer has decided to remove what I believe to be called a blue screen of death, that this happened before and I thought it was part of the installation but when I turned my computer on he showed at the bios screen , but then it said 'unable to start Windows. A recent hardware or software change might be the cause. To solve the problem: 1. Insert your windows installation disc and restart your computer. 2. choose your language settings, and then click Next. "3 click on repair your computer ' all this is very well apart from the fact that I do not have the windows installation disc. I'm stuck at this screeni however have a disc of windows 7 and that he was going to install windows7 after I got my vista Setup! but the only I see is the bio screen so I was wondering if there was some way I could install windows 7 from the bios or simply delete the entire half installed this error files windows vista from the bios screen? Please, any help is greatly appreciated. Or get a new internal HDD would fix the problem aswell?

  Hello

  You can check out the following link and check:

  Installation and reinstallation of Windows 7

  http://Windows.Microsoft.com/en-us/Windows7/installing-and-reinstalling-Windows-7

  See also, how to start your computer from a Windows 7 installation disc or USB flash drive.

  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-from-a-Windows-7-installation-disc-or-USB-flash-drive

  Note:

  If the copy of Windows 7 is an upgrade, you will need to install a full version of Windows Vista and then upgrade to Windows 7

  I hope this helps!

• ERROR: Unable to start Bluetooth stack service

  I seldome use features wireless to my pc before, but now that I have the wireless router I frequelty use it. Usually, I turn on the wireless switch and turned off to save the battery. I noticed every time I turn on the radio, after a few minutes, that an error message is displayed:

  BTTray

  ERROR: Unable to start Bluetooth stack service

  I don't know if what is wrong with my laptop. Please if anyone can tell me if what is wrong with this thing. Thank you very much!

  HP pavilion dv6820ee

  OS: Windows Vista editions Home premium.

  Message edited by xXxonins on 12/22/2008 05:27

  Access your product download page and reinstall the software for bluetooth under networks:

  http://h10025.www1.HP.com/ewfrf/wc/softwareList?OS=2093 & LC = on & DLC = in & CC = US & Product = 3716846 & lang = in

  then, under network connections in the network and sharing window - see if you have a bluetooth adapter that is listed.  If you do not use bluetooth, you can turn it off or you should be able to set it up properly.

  If fails it then in Control Panel, under administrative tools, Services - locate service BTtray and disable it.

  HTH

• On Windows 7, after the update of Lightroom 2.6 to Ligthroom 6 I am unable to fix photos [was: Hello,]

  On Windows 7, after the update of Lightroom 2.6 to Ligthroom 6 I am unable to correct photo

  The program (Lightroom 6.3) systematically freezes and needs closure after every temptation of correction development.

  The development and mailing of the crush program program ' are at Microsoft did not help.

  My system dump here:

  Lightroom version: 6.3 [1052427]
  License: Permanent
  Operating system: Windows 7
  Version: 6.1
  Application architecture: x 64
  The system architecture: x 64
  Number of logical CPUs: 4
  Processor speed: 2.5 Ghz
  Built-in memory: 8155.1 MB
  Memory real available pour Lightroom: 8155.1 MB
  Real memory used by Lightroom: 1035.4 MB (12.6%)
  Virtual memory used by Lightroom: 1007.6 MB
  Cache memory size: 100.3 MB
  Maximum number of links used by Camera Raw: 4
  SIMD optimization of Camera Raw: SSE2, AVX
  The system DPI setting: 96 DPI
  Composition on the Desktop enabled: Yes
  Views: 1) 1920 x 1080
  Input types: multipoint touch: no, touch integrated: no, built-in pen: no, touch external: no, External plume: no, keyboard: no

  Parents to the graphic processor information:
  AMD Radeon HD 7800 M series

  Check the supported OpenGL: past
  Vendor: ATI Technologies Inc.
  Version: 3.3.13399 context 15.200.1062.1004 the base profile
  Renderer: AMD Radeon HD 7800 M series
  LanguageVersion: 4.40

  
  The application folder: C:\Program Files\Adobe\Adobe Lightroom
  Access to the library path: E:\Lightroom\Lightroom catalog Qnap - 2.lrcat
  Settings file: C:\Users\Joe\AppData\Roaming\Adobe\Lightroom

  Installed modules:
  (1) external module connected mode Canon shooting
  (2) external module of shooting in connected mode Nikon

  Markers Config.lua: no

  Adapter n ° 1: supplier: 1002
  Device: 6827
  Subsystem: 31e1002
  Revision: 0
  Video memory: 1003
  AudioDeviceIOBlockSize: 1024
  AudioDeviceName: 1 - Philips FTV (AMD High Definition Audio Device)
  AudioDeviceNumberOfChannels: 2
  AudioDeviceSampleRate: 44100
  Build: not initialized
  Direct2DEnabled: false
  GPUDevice: not available
  OGLEnabled: true

  Thanks for the help!

  Go to Preferences, click the performance tab, and then uncheck the box.

• Unable to start the computer after completing the system scan using Microsoft Security Essentials BSOD error (: 0x0000007B)

  Original title: I cannot restart my computer and start windows after the analysis of the system running and the removal of any bad programs with Microsoft Security Essentials.removing
  I cannot restart my computer and start windows after the analysis of the system running and the removal of any bad programs with Microsoft Security Essentials. I have rebooted, tried to finally start work configiration and back still an error for windows startup. Attempted to enter the mode by F8 safe failed I then chose without auto restart in F8 and get the BSOD - he tells me to search for viruses and run chkdsk/f, but I can't access it. I tried to restart and it still does not work. technical information on the BSOD readings * STOP: 0x0000007B (0xF7ae9528, 0xC0000034, 0 x 0, 00000000 000000000. Please help it is essential to address them ASAP edition)
   

   

  Hello

  You can try the troubleshooting provided in the links below steps to fix the problem.

  Advanced troubleshooting of errors "Stop 0x0000007B" in Windows XP

  http://support.Microsoft.com/kb/324103

  Error message "STOP 0x0000007B" when you restart your Windows XP-based computer

  http://support.Microsoft.com/kb/316401

• Need help message' w/error Unable to start the s window media Interface. Make sure you have at least WMP10. »

  I downloaded WMP11 to download another program and I get this message ("unable to start the s window media Interface. Make sure you have at least WMP10. »).  This message appears when I click on the new program and it loads.  As soon as it loads the first program screen appears and displays this error message on WMP 10.  When I click ok it goes, but I can't get the new program to do anything.

  So before asking on the problem of new program, I would like to fix this so it keeps popping up.
  I'm not too calculates saavy so I need clarification.

  Thank you

  Where did you downloaded WMP 11?

  Uninstall WMP 11 and check again the issue. If it stops then reinstall WMP 11.

  http://Windows.Microsoft.com/en-us/Windows-XP/help/Windows-Media-Player/11

  http://www.Microsoft.com/download/en/details.aspx?displaylang=en&ID=8163

• Unable to start - blue screen after Windows update

  original title; on dell dimension C521... blue screen after Windows update last night 3/9...3:00am...running Vista

  Can not even go in safe mode

  Hello

  try to do a startup repair or a system restore before the update using the Startup Repair disk if you don't have a vista dvd microsoft

  the link below is how to download and get a vista disk startup repair, which you can start from the

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  Here's how to use startup repair system restore command prompt, etc. to bleepingcomputers link below

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  to boot from the dvd drive to be able to you will see a way to get into the bios Setup at the bottom of the screen or command menu start

  It would be F2 or delete etc to enter the BIOS or F12 etc. for the start menu

  Change boot order it do dvd drive 1st in the boot order

  If you can make the above change how you receive updates to find the update problem

  When right-clicking on it UAC prompt you hide it

  http://www.bleepingcomputer.com/tutorials/tutorial140.html

  Choose one of these settings:

  Download updates but let me choose whether to install them - if you select this option, Windows will download the updates on your computer, but not install them automatically. If you want to install updates, then you must install them manually. You should only select this option if you have a reason to not install updates automatically. Only advanced users should use this option.

  Check for updates but let me choose whether to download and install them - if you select this option, you'll be alerted when there are new updates available for download and install. You can then choose to download and install the updates that you want. This option should really be reserved for people who know exactly which updates they need, or those who have little access to the Internet.

• Windows has recovered from an unexpected error when I start my laptop after hibernating my laptop.

  Hello! I met an error that says:

  Windows has recovered from an unexpected shutdown.
  I don't know what to do. I'm afraid that the persistence of this error can damage my laptop. Here's the full description:
  Problem signature: problem event name: BlueScreen
  OS version: 6.1.7601.2.1.0.256.1
  Locale ID: 1033
  More information about the problem:
  BCCode: fe
  BCP1: 00000008
  BCP2: 00000006
  BCP3: 00000005
  BCP4: 85EE29D8
  OS version: 6_1_7601
  Service Pack: 1_0
  Product: 256_1
  Files helping to describe the problem:
  C:\Windows\Minidump\092312-34803-01.dmp
  C:\Users\windows user\AppData\Local\Temp\WER-96970-0.sysdata.
  Link to the download dump file: http://www.mediafire.com/?3ejf48zi6qg16wm
  Download link for the sysdata file: http://www.mediafire.com/view/?sygw329mlil7y2i
  THANKS TO ALL WHO TAKE THE TIME TO REVIEW MY POST.
  God bless us!

  1. Avast can be a cause of BSOD.
  Please delete and replace by Microsoft Security Essentials at LEAST FOR TESTER

  http://files.avast.com/files/eng/aswclear5.exe
  http://www.Microsoft.com/security_essentials/

  2. your crash was related to ZTEusbnmea.sys USB Modem/Serial Device Driver ZTE Incorporated.

  Please install the most recent available.

  How to find drivers:
  -Google search for the name of the driver
  -compare Google results with what is installed on your system to determine on what device/program, it belongs to
  -Visit the web site of the manufacturer of the hardware or program to get the latest drivers (do not use Windows Update or Device Manager Update Driver function).
  s ' there is difficult to locate them, post back with questions, and someone will try and help you find the right program

  The most common drivers are listed on this page: driver reference

  http://www.carrona.org/dvrref.php

  http://SysNative.com/drivers/

  -Driver manufacturer links are on this page: http://www.carrona.org/drvrdown.htm

• I'm unable to start Windows Security Center "error 193: 0xc1»

  Original title: I cannot start Windows Security Center

  Hello

  I manage not to launch Windows Security Center, I use windows 7 64-bit.
  I go to services and local services-click and scroll down to Security Center, I then click on highlight, then click Start, I get a loading bar but then an error message that reads: error 193: 0xc1
  How can I get the business to start?
  Thank you very much
  Nick

  Hello

  You did changes to the computer before the show?

  Method 1:  SFC scanner.

  System File Checker (SFC) scan will replace the missing or corrupted system files on your computer.

  Use the System File Checker tool to troubleshoot missing or corrupted on Windows Vista or Windows 7 system files:

  http://support.Microsoft.com/kb/929833

   

  Method 2: I suggest you make a system full scan just to be sure.

  Here is a link that will give you information on how to perform a full scan of the system:

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.