Error usb-6212 "reading port.vi digital" reading: Subvi is missing

Hello

I try to have the LabVIEW to recognize my USB but I got the error "digital port.vi read" is missing. I was wondering if there was a resouce for sample VI? Or how to write a VI in order to recognize/read the digital signals of e/s?

Thank you very much!

Hi blizabeth37.

If I understand you correctly, you are looking for e.g. screws, correct?  Have you tried looking at the example Finder LabVIEW?  Examples in LabVIEW, click Help.  "Once in the Finder of the example, for digital i/o, obtained material input and output" DAQmx "digital generation or numerical measures.  Carefully read these files, and you should find something that does what you want.

Alternatively, you can go to the online community to find, for example, code: www.ni.com/community

I hope this is what you were asking.  Good luck with your application!

Tags: NI Hardware

Similar Questions

  • Digital and analog inputs simultaneously - NI USB-6009 and NI USB-6212 - ANSI C

    Hello

    I'm reading at all times and at the same time analog and digital inputs. Digital and analog samples must be sampled at the same clock and acquisition should be started (triggered?) at the same time (I don't want, after some time, analog reception more digital samples - the opposite is also true).

    I found an example (in C source code) "National Instruments\NI-DAQ\Examples\DAQmx ANSI C\Synchronization\Multi-Function\ContAI-Read dig Chan" and tried to run with two USB cards: NI USB-6009 and NI USB-6212. Unfortunately, the two results by mistake, as described below:

    DAQmx error: the requested value is not supported for this property value.
    Property: DAQmx_SampTimingType
    You asked: DAQmx_Val_SampClk
    You can select: DAQmx_Val_OnDemand

    Task name: _unnamedTask<1>

    State code:-200077
    End of the program, press the Enter key to exit

    -Is it possible sync analog and digital acquisition in the paintings?

    -If so, how?

    Thank you

    Hello tcbusatta,

    Two of these modules, USB = 6008 and USB-6212, support only timed software inputs and digital outputs.  This means that you cannot define material timing (like finished sampling or continuous) for these modules.  Digital lines can be retrieved or written once to each call DAQmx read.

    This means that you will not be able to get any type of synchronization tight between the analogue and digital channels.  You will need a Board such as the NI USB-6341 in order to synchronize the AI and DI closely.

  • Satellite Pro L300 - USB card reader does not support the 64 GB

    HI I have a Satellite Pro L300 under Win XP that I want to attach a USB card reader. I find that I can not read the 64 GB cards. The error is that the card is not formatted. All other cards read correctly. I can place this card reader in my desktop running Win 10 and it works correctly and reads the 64 GB cards. This seems to indicate that the USB card reader works properly, and perhaps that the problem lies in the USB on the Toshiba drivers. Has anyone else had this problem and found a fix for this. I've just updated the BIOS but no improvement. Thank you

    Posted by Trees
    HI I have a Satellite Pro L300 under Win XP that I want to attach a USB card reader. I find that I can not read the 64 GB cards. The error is that the card is not formatted. All other cards read correctly. I can place this card reader in my desktop running Win 10 and it works correctly and reads the 64 GB cards. This seems to indicate that the USB card reader works properly, and perhaps that the problem lies in the USB on the Toshiba drivers. Has anyone else had this problem and found a fix for this. I've just updated the BIOS but no improvement. Thank you

    Hi, here is a link to not detected by the PC card reader:
    http://KB.SanDisk.com/app/answers/de...CTED-by-the-PC
    You can take a look, hope it will be useful to you.

  • ERROR 1073676294? READING OF VISA...!

    How you guys doin. ?

    I got the error above when reading my ECG sensor via a serial port data... you guys would help me with the following steps?

    1. I see that there is a signal showing disappears a second and then go back to appearing and so on.

    2 - the number of bytes read varies between 1 and 2 only... I think it's impossible... I send you an ECG signal so the number of bytes expected to be much higher.

    the attached picture can show you the result that I want to come...

    any help would be appreciated!

    It looks like the LabVIEW code, at least the part series, works very well. If the waveform is not correct, check your connections to the probe and the programming of the microphone.

  • USB card reader

    I use HP Compaq dc7800 compact format, hp s/n: 2UA8491BGS p/n: AQ532US #ABA and Windows 7 Home Premium x 86 SP1, where can I find the USB card reader? http://h20566.www2.HP.com/portal/site/hpsc/template.page/public/PSI/swdHome/?javax.portlet.begCacheT...

    I appreciate it!

    Hello

    They are normally devive P-n-P. You just need to buy a care USB drive and plug it into the USB port, the card will end up as a drive in Windows Explorer. No drivers required.

    Kind regards.

  • NAS200 USB card reader

    Is it possible to install a multi card reader into the usb port on the NAS200. I have no problem with the usb key, but can't seem to map to the card reader. See you soon

    No it's not possible to attach a USB card reader... The NAS200 is USB Port is designed and cannot read USB hard drive connected to it...

  • Constant error - "Adobe Acrobat Reader DC has stopped working"

    Recently, we purchased a new high-end Dell Precision Workstation from Dell and bought Adobe Acrobat Standard DC with him (Dell).

    At the reception of the computer, whenever we try to open a PDF file, or do anything related to a PDF file, we will randomly get a dialog box of Windows indicating "Adobe Acrobat Reader DC has stopped working".

    I've attached a screenshot of this error.

    Adobe Acrobat Reader DC Has Stopped Working.JPG

    PLEASE NOTE THAT THE ERROR INDICATES 'ACROBAT READER DC', BUT WE HAVE NOT INSTALLED CD PLAYER - ONLY ACROBAT STANDARD DC

    Specifically, it can be almost ANY Acrobat associated action that triggers this error, including:

    • Opening Acrobat Standard DC
    • In Windows Explorer, when you browse a folder containing PDF files in it, and when clicked (to highlight) a PDF icon on screen
    • Doubleclicking on a PDF from Windows Explorer.
    • Saving as a PDF, or print a document to a PDF file.

    I searched this error online widely and tried all the 'solutions' that I read. This is a COMMON problem, and it shows messages from the forum that Adobe does not have the problem, or is not a way to fix the problem.

    I tried a recommendation - that happened to Adobe's Forum Moderator, to uninstall the program, then run

    AdobeAcroCleaner_DC2015.zip, which apparently removes any vestige of the previous installation.

    After uninstalling, cleaning, then with the software, then reinstalling the original version that we bought (which, according to the configuration of the sysinfo file is Version 15.6.30033.133277) - ORDER of the ERROR, AND IT has WORKED FINE for 3 DAYS. Prior to this relocation, it would crash with this error about 1 times per minute (sometimes more or less frequently), but constantly, so when we arrived 3 days not a mistake, I assumed that this problem has been corrected.

    Then, on 18/08/15, the errors started. I checked the Windows Update since Adobe has updated the entire program and there is no option to "Uninstall" the update (apparently either Adobe which is off, or if they replace the entire program, you cannot uninstall the update). The Version on this 'update' code was 15.006.30060. I confirmed that the program had be reinstalled via Windows Update automatically, and the date of installation of program in Control Panel was in fact 18/08/15.

    So, I repeated this process, uninstall the program, the race of vacuuming, reboot, connecting the Adobe ID account, then by reinstalling the ORIGINAL version, we bought Dell "Dell digital delivery" process - to reinstall our original version - which had already solved the problem for a couple of days.

    THIS TIME, IMMEDIATELY AFTER you HAVE REINSTALLED, I TURN OFF ADOBE UPDATER, thinking that it would disable future updates.

    Overnight, we came into work and saw that the program was no longer updated automatically once himself again, despite the fact that the update from Adobe was extinguished, it again, updated in any case!

    Of course, since it was updated, the constant errors started again, just like before!


    I could repeat this process continuously, but its a lot of your time for our IT Department to keep mounting, and the error reappears just apparently every time that Adobe did an update. And speaking of which, why can't NOT UNINSTALL a "Adobe Acrobat Standard DC update" when you uninstall other issues updates to Windows for example?

    My PC is Windows 7 Service Pack 1. It is 64-bit.

    At this point, our options are either to get the problem fixed, or discontinue use and uninstall the program - we really need because that person publishes our CAD designs out in PDF format for documents control.

    This PC is a new precision workstations Dell - straight out of the box and is running Windows 7 64-bit with Service Pack 1

    PLEASE HELP ME SOLVE THIS PROBLEM! I spent several hours EACH day for a week, try to solve it, but based on the number of complaints about what I found online it seems to be a problem purely of Adobe, and replacing "Refresh" the DIFFICULTY ISN'T THE PROBLEM if it's what it was intended to do.

    Thank you

    Dave

    Hey Joe,

    Thanks for the help. However, we have solved the problem. We have added very early in the directory that you are proposing, but it did not help.

    One of the Tech Support guys Adobe we finally talked to suggested disabling the "Preview Pane" feature in Windows Explorer and it immediately solved the problem. Since then, we have had no problems.

    This is only a workaround, however, as the preview pane was invented for a reason - to visually identify files based on the forecast of nail. We work with many, many files of CAD data, and this preview function allows to visually identify a file based on the image much faster than having to read the file name - which in our case is long and technical, CAD Solidworks file names.

    Thus, we have so much need for Adobe to fix this feature so that Windows Explorer can display a preview of PDF files. Its a shame to have to put out in the world, just because of a problem with a single application (Adobe Acrobat DC!)

    Thanks for your help!

  • Satellite Pro P100: remote control does not not-&gt; error ' cannot be read handle. ".

    Hello

    My Satellite Pro P100 began to show the error "Failed to read handle." at startup. I found a related post and removed from the area of registry Toshibarc.exe control startup programs. This does not prevent the pop-up dialog box, but now my remote does not work.

    Does anyone know if toshibarc.exe must run for the remote control work? And if so, how do I fix the error in the program (rather than simply removing from the register). Could this be a hardware problem?

    If I try to manually run the C:\WINDOWS\SMSC\CIRHID\V1_0_0000_0\toshibarc.exe, I get the same popup "Impossible to get read handle.".

    Thanks for any help or ideas
    Steve

    After a long period of investigation in the internet and visit many Web sites, I discovered that the ToshibaRC.exe file belongs to the Remote Application from Toshiba. It seems that the file is required to use the remote on the laptop...
    But I can't give you a reason why it causes an error.

    I found this similar thread in the forum
    http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=16959

  • Error "Unable to read your flow." for RSS valid

    I'm looking to submit a custom podcast created to Apple via Connect of Podcasts. I'm getting an error "Unable to read your flow." wave without telling me what exactly is the problem.

    Food is works well in iTunes and check completely clean in the RSS W3 validator: e https://validator.w3.org/feed/check.cgi?url=http%3A%2F%2Fsassaman.com%2Frss%2Fcc

    I manually added the stream iTunes (version 12.3.2.35 on Windows 10) and it worked great for awhile. Every Sunday I add another episode of the feed and it downloads in iTunes, syncing my iPhone, everything works fine.

    Headers of the response of the application of wire - rss look good, correct content type and encoding. Food is displayed correctly in FireFox as well:

    HTTP/1.1 200 OK

    Cache-Control: private

    Content-Type: application/rss + xml; charset = utf-8

    Server: Microsoft-IIS/8.0

    X AspNetMvc-Version: 5.2

    X-AspNet-Version: 4.0.30319

    Date: Wednesday, February 24, 2016 02:13:22 GMT

    Content-Length: 21997

    So I can think of all possible tests the food is valid, including widely validated by Mark I eyeball that all tags are good. I'm puzzled.

    The only thing I wonder is that iTunes is somehow an analysis of enclosure and dislikes served from static links on Vimeo.com boxes? I wish there was some sort of mistake, I don't have an idea why it cannot read my podcast.

    Food seems to be OK. You have no episode 'itunes:subtitle' or 'itunes:summary' tags so your episodes show no description, but it would not have prevented the store read the stream. The episodes seem OK - the URL begins with https rather than http, but this used to be a problem it seems to be now. If they had problems with real media files episode the error message would say that they were "difficult to download episodes from your stream.

    So I don't know what the problem is. Maybe your server because the power is negative reaction to specific applications on the iTunes Store - this has been known to occur even though it is unusual - while being OK with the iTunes application and browsers. You can try to ask for the support of aid, but essentially they will only address problems at their end, not yours. Go to https://itunespartner.apple.com/en/podcasts/overview and click on the link "Contact us" at the bottom of the page.

  • The USB-6009 reading signals

    Hello

    I use 6009 USB to read the signals of the PMT and other equipment for experiments and I have a few questions:

    1. is it possible to read a signal with DAQ assist? I looked around forums and have not seen any relevant element.

    2. it is probably true, but I have not yet checked. Is it possible to read the two signals in the same loop (for example, AI0 & AI2 in awhile put in loop)?

    I would be grateful if you point me to the right direction.

    Thank you

    A

    P.S

    I should probably mention that I want to read the signals with using DAQ hardware help because of the assumption that the DAQ Assistant is slower than a direct measure.

    HEY Fan, Ravens

    Nevermind, I figured it out... Well the first step of it at least :-).

    Thank you once again,

    A

  • 4810 error to its reading file Open.vi

    Hello

    I'm getting a '4810 error to file read Open.vi' for the attached wav file (much to other wav files).

    Any ideas?

    Thank you

    Rob

    What kind of Labview version do you use? Your file will play with the old sound system. As it is robust. In your Labview installation folder, locate the vi.lib folder. Check if you can find a folder named sound inside of this folder. Locate the the lvsound.llb and open the 'Snd play Wave File.vi '.

  • 200609 error on upgrade of PCMCIA 6036 - E USB 6212-M

    We recently replaced a bad card PCMCIA 6036-E with a USB 6212 M-series.

    Since we use NEITHER-DAQmx, the upgrade was supposed to be plug-and-play.  However, I get an error 200609 (too small buffer size) when you try to run a program, Labview 8.6, which went perfectly with the 6036.  The problem seems to occur with Assistant6 of data acquisition (see attachment) that generates a voltage out analogy.   DAQ assistant settings are set on "Generation Mode" = continuous samples, "Samples to write" = 10, rate (Hz) = 200.

    Nothing within the program has been modified since the upgrade to the USB6212.

    Any help would be greatly appreciated.


  • Cannot get my usb card reader to work because I plugged my new wireless broadband

    HI MY PLUG-AND-PLAY DIRECTED BY ABC PRODUCTS USB CARD READER WAS WORKING UNTIL WEEK LAST I CHANGED MY CONNECTION TO BROADBAND CABLE TO CONNECT NEW WIRELESS I UNPLUGGED AND REPLUGED INSIDE BUT STILL DOES NOT?

    JOHN SOON

    Hi John,.

    1 Windows operating system you are using?

    2 are you facing issue with other devices usb also?

    You can read the following article and try to run the material Fixit and see if it helps.

    Hardware devices do not work or are not detected in Windows

    Hope this information is useful.

  • USB card reader does not detect memory cards

    memory card

    I do not have a slot for memory card but I have a usb card reader, but it just recently stopped reading all my memory cards? What should I do?

    Hello

    If you can't get the working card reader, you can use a card reader that is
    not expensive.

    -------------------------------------------------------------

    To check your version of Windows.

    Check with the manufacturer of system and their forums (if any) for known issues.

    Your other USB devices work?

    Try a system restore to before the drive stopped working if possible.

    How to do a system restore in Windows 7
    http://www.SevenForums.com/tutorials/700-system-restore.html

    -----------------------------------------------------------

    If necessary:

    References to Vista also apply to Windows 7.

    Follow these steps to remove corruption and missing/damaged file system repair or replacement.

    Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

    sfc/scannow

    How to fix the system files of Windows 7 with the System File Checker
    http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

    Then run checkdisk (chkdsk).

    How to run check disk in Windows 7
    http://www.SevenForums.com/tutorials/433-disk-check.html

    -----------------------------------------------

    Then lets refresh the USB stack

    Control the click Control Panel - Device Manager - anywhere in the area of white/white - point of VIEW, then-
    Show hidden devices

    Look everywhere EXCEPT USB controllers for your device and if find you them (maybe
    plus_d' one of each) under disk drives, you can have several - right CLICK and UNINSTALL
    for all instances.

    Control Panel right CLICK on EVERYTHING - Serial USB controllers - device configuration-manager and
    UNINSTALL all but the category itself - REBOOT - it refreshes the drive and battery USB

    This KB shows XP how to and methods of Vista and Windows 7 are the same
    http://support.Microsoft.com/kb/310575

    This is a utility to help you, but do 1 above.

    USBDeview is a small utility that lists all USB devices currently connected to your computer.
    as well as all USB devices that you previously used. Run Options and tick the three 1st choice
    to see if one is there.

    http://www.NirSoft.NET/utils/usb_devices_view.html

    You must remove all instances of the devices and restart.

    ----------------------------------------------

    If necessary try these two:

    Tips for solving problems of USB devices - and a Mr Fixit
    http://windowshelp.Microsoft.com/Windows/en-us/help/c39bd203-f729-47a4-8351-83291e13c8a81033.mspx#EGB

    Hardware devices not detected or not working - Mr. Fixit
    http://support.Microsoft.com/GP/hardware_device_problems

    ----------------------------------------------

    This can be useful to determine if the wrong driver is loading.

    -Free - DriverView utility displays the list of all device drivers currently loaded on your system.
    For each driver in the list, additional useful information is displayed: load address of the driver,
    Description, version, product name, company that created the driver and more.
    http://www.NirSoft.NET/utils/DriverView.html

    I hope this helps.

  • Impossible to remove a file from the desktop, get the error message "cannot read the source file or disk.

    I can't delete a file from my counter top. Error message: cannot read the source file or disk. He is an Adobe file with logo in white box.

    Boot into safe mode and see if it will remove. If this is not the case, try this tool.

    Unlocker File Remover

    Download it from FileHippo
    http://filehippo.com/download_unlocker/

    Download from CNET
    http://download.CNET.com/WOT/3000-2378_4-75011499.html

Maybe you are looking for

  • Can not connect to Skype for a few days

    Hello Problem is Skype on iPad to one of my clients. Because this isn't my iPad, I have limited access to the devices. In addition, he is Polish language so messages below can be translated, not exactly. A few days ago (~ 7.08.2014), Skype does not c

  • How to link two labview files

    Hello I have a file that generates a signal, I connect the signal generated in the first to the second file. You can help me please how to do this. waiting for your answer.

  • communication of the PSC-1804 by PSC-2220 blocking code RT

    I'm trying to communicate to a PSC-HAVE-100 on a PSC-1804 through a PSC-2220.  I got it for several months with many updates/revisions of the labor code and then the PVD code start correctly (code falls down during the first iteration and cfp-2220 fl

  • Table of graphs

    I created a table 1 d of XY graphs and to make friendly Viewer, I would break it up into two columns (if I have 6 slots, I want to see them as an array of 3 x 2 instead of 6 x 1). The algorithm works very well, I tried with other types of data, but d

  • Movie Maker: can not make dvd, unspecified error

    I made a holidaymovie with Windows Movie Maker 6.0, working with Vista Ultimate SP2 on a laptop Acer Aspire 9420. Got more memory (4 GB RAM). It has 20 GB free and the D-disk 40 GB of free space on my C drive. The original camera film is on an extern