ESXi does not connect to vCenter

Hi guys need help from anyone.

I have restored my server ESXI ESXI on HP G8 5.5U3

and now I can not add it to my vCenter

I have a verified network connectivity all the firewall settings are OK nothing that should block add the server to vCenter

I can connect to the server directly with the customer high C

I am connected with SSH and I restarted the management agents with services.sh restart won't always add in

tried to add an another vCenter we have and will not add

so I have re installed the image thinking 5.5 the esxi had been corrupted and it worked I've added it to vCenter

now he is again abandoned the vCenter after reclamation again and will not add not in

error

Reconnect the host

ESXi - 455.ce.beavers.com

Failed to contact the specified host

(ESXi - 455.ce.beavers.com). The host

may not be available on the network, a

network configuration problem may exist,

or management on this host services

can be unresponsive.)

Help me please what could happen here,

Thanks in advance

I got this case, where I'm running ESXi 5.5 u3b, try to connect it to a U2/U3 5.5 vCenter.

The difficulty here is, IF you use a host ESXi U3b 5.5, then your vCenter should be 5.5 U3b as well.

Product build VMware KB: Correlation between VMware numbers for update levels

Use the above KB article and search for free your ESXi build corresponds to the. If it is 5.5 U3b, then check that your Build vCenter corresponds to (vCenter > help > about VMware vSphere)

If 5.5U3b ESXi and vCenter isn't, then pass the vCenter 5.5 U3b

Suhas

Tags: VMware

Similar Questions

  • 5.5 ESXi does not connect to VCenter 5.5

    I'm under VMware ESXi 5.5:

    Product: VMware vSphere Enterprise 5, Plus allowed for 2 processors physical (unlimited cores per processor)

    I installed VCenter 5.5 and the Appliance virtual VMWare.  However, when I connect to the web interface, I do not see the ESXi server, nor do I have the possibility to add the data center, or add anything else.  The VCenter 5.5 software all runs on Windows Server 2012 R2 Standard.  I have disabled all firewall on this machine just to exclude.  I can connect to port 902 this machine ESXi machine.  I don't know what I'm doing wrong.  Looking at the logs on the computer of ESXi, I see no mention of it trying to connect, unless I'm looking in the wrong place.

    Can someone point me in the right direction on how it works?  I looked everywhere on the VMWare Web site and followed all the instructions, nothing good.  I even edited the vcpx.cfg file and manually add the IP address of the machine of VCenter.

    If you need me to post logs / files of configuration or anything else, I will do so.

    Thanks in advance!

    Hello

    Screenshots of the problem you are experiencing would help a lot. Anyway, when you connect to the Web Interface, your first login must be in the [email protected] and the password you configured during the installation of the device. This will allow you to create all the objects, you need and assign the access rights that are related to your domain account.

  • BDE 2.1.1 Fling Management server does not connect to vCenter

    I have the management server deployed in the environment, the plugin installed successfully and vCenter is connected to the administration via the Web interface of vCenter server. This problem occurs when I go to a data store or add it to a network.

    I get the following (via the GUI or CLI):

    Version: 2.1.1

    Welcome to Serengeti CLI

    Serengeti > Connect - host hadoop - mgmt.or1.omniture.com:8443

    Enter the user name: [email protected]

    Enter password: *.

    Connected

    Serengeti > data store, add - name defaultDS - spec DS10HadoopOR1 - shared type

    datastore defaultDS add failed: unable to connect to vCenter Server.

    The error in the serengeti.log file is a generic JAVA error. The vCenter is 5.5U2 and ESXi hosts are 5.5U1.

    --

    Chris.

    Thanks Charlie for a helping hand.

    I found some info in the serengeti.log and the serengeti - boot.log Chris post:

    Serengeti - boot.log:

    I, [2015-02 - 12 T 20: 56:27.722910 #3336] INFO -: templateVmName: vSphere Big Data Extensions - Node Template

    Serengeti.log:

    Caused by: com.vmware.bdd.utils.AuAssert: FAILURE

    at com.vmware.bdd.utils.AuAssert.FAILURE(AuAssert.java:28)

    at com.vmware.bdd.utils.AuAssert.check(AuAssert.java:43)

    at com.vmware.bdd.utils.AuAssert.check(AuAssert.java:50)

    at com.vmware.bdd.service.impl.ClusteringService.getTemplateVm(ClusteringService.java:408)

    [2015 02-12 T 14: 46:47.438 - 0700] INFO Event_Expander | com.vmware.bdd.service.event.EventScheduler: to develop events: [{me = null: VirtualMachine:vm - 136, event = VmResourcePoolMoved}]

    [2015 02-12 T 14: 46:47.626 - 0700] INFO pool-2-wire-4 | com.vmware.bdd.service.utils.VcResourceUtils: folder xxx-uuid was not found.

    [2015 02-12 T 14: 46:47.627 - 0700] INFO pool-2-wire-4 | com.vmware.bdd.service.event.VmEventManager: VM root folderxxx-uuid is not yet created. Ignore the event outside of VM.

    [2015 02-12 T 14: 46:58.393 - 0700] Event_Handler INFO | com.vmware.bdd.service.event.EventScheduler: processed 2 new events

    [2015 02-12 T 14: 46:58.394 - 0700] Event_Handler INFO | com.vmware.bdd.service.event.EventScheduler: processed events: [{me = null: VirtualMachine:vm - 137, event = VmResourcePoolMoved}, {me = null: VirtualMachine:vm - 136, event = VmResourcePoolMoved}]

    [2015 02-12 T 14: 47:13.183 - 0700] Http-8443-5 ERROR | com.vmware.bdd.rest.RestResource: rest call error

    com.vmware.bdd.exception.BddException: unable to connect to vCenter Server.

    at com.vmware.bdd.exception.BddException.INIT_VC_FAIL(BddException.java:189)

    at com.vmware.bdd.rest.RestResource.verifyInitialized(RestResource.java:1175)

    at com.vmware.bdd.rest.RestResource.addDatastore(RestResource.java:636)

    This log shows THAT BDE Server cannot find the node named "vSphere Big Data Extensions - Node Template" model.  When you deploy the BDE Fling, the management server and hadoop-model VM must be deployed in the same folder in, under a pile of vCenter.  Please check and follow the BDE 2.1.1 Fling deployment guide and deploy again.  BTW, you can customize the name of the server VM and the VM model during their deployment and make sure the correct model name together when you deploy the server VM.

  • 1st install ESXi does not connect to the network

    I used VMware Fusion and several versions of the workstation. I am a computer SCIENCE student and I'm trying to set up a virtual server for the purpose of learning environment.

    First, I installed ESXi in workstation computer on my laptop. I scare IT LIKED. I ran to the store bought a fresh HDD to install ESXi to my old server Supermicro (MBD-PDSMA + o LGA). During installation, I received a warning that the Intel Virtualization has been disabled on my motherboard. I activated that can restart the installation. No matter what I try I can not this 'thing' to get an address from my DHCP server. I even tried unpluging my router and using several computers on my network as DHCP servers. Each of them I tried my entire network has received fresh IP address but my supermicro box did not. I tried to use two network, port 0 only ports and only 1 port. After having lost about 24 hours I tried to install 5.0.0 and it worked without problem. I would like to be able to update the latest versions unmolested my network connection is going to die on me when I do.

    Ideas?

    My next issue will be storage because not even my JABOD drives appear in my passthrough RocketRaid 2220 and PCI does not seem to be an option for this card. Yep, that's good baby PCI - X... Say what you want about RocketRaid, this card was sitting at the bottom of a box of son with no static case a few years to 3-4 moves and it still works like a champ.

    I had the same problem with a card mother similar supermicro who has the same Intel Lan Adapter as yours.  Using the e1000 drivers of 5.0 worked for me.  I followed the instructions in this thread:

    http://communities.VMware.com/message/2115391#2115391

  • 5.1 ESXi does not connect after installing - R720 Dell

    I installed ESXi 5.1 update 1 on a Dell R720 server. The installation was made using ISO provided custom in the Dell site.

    After installation I can't connect or ping to the machine.

    After SSH-ing to the host via the console I could see that the host can ping to its own IP address, but not of its front door.

    Is this a problem with the network Dell drivers?

    Information: There are 4 network cards. All are Gigabit Ethernet of Broadcom Corporation NetXtreme BCM5720 cards.

    esxcfg-NICS - l gave me the output below:

    Esxi 5.1.JPG

    Please help me with this.

    Hello

    You should check the configuration of your network management. If the IP, subnet mask, gateway, DNS are correctly configured and if it it set to vmnic3, as it is the only NIC you connected.

    If everything is correct, I would check the physical switch of the server config is connected to. Maybe the port is blocked or a bad local VIRTUAL network is configured.

    Tim

  • Guests who will remain not connected to vCenter

    4.1.0 ESXi and vCenter 4.1.0

    We have four hosts in a cluster, two have no problem while the other two will remain not connected to vCenter.  I checked all that in the article 1003409 (http://kb.vmware.com/selfservice/microsites/search.do?language=en_US & cmd = displayKC & externalId = 1003409) and found no problem.

    Four servers are IBM x 3690 X 5 and all are connected to the same four SAN LUNS, the only difference is that for problem servers management interfaces are on a different subnet, but the port UDP 902 is open between them and the vCenter server.  I can reconnect manually, but they will be disconnected again in a minute or two.

    Does anyone have ideas beyond what is in the article 1003409 that I can check?

    Thank you

    Darryl

    Make sure you have port 902 open TCP , as well as UDP.

    See this article: http://kb.vmware.com/selfservice/documentLinkInt.do?micrositeID=&popup=true&languageId=&externalID=1012382

    Regarding the 902 TCP port:

    vCenter Server system uses to send data to managed hosts. This port should not be blocked by the firewall between the server and the host or between hosts

    If the problem persists, I would try to remove the host to vCenter inventory, add new. Who's going to reinstall agents vCenter on the hosts.

    EDIT: This particular excerpt was taken from the entrance to vCenter 5.x, but the same is true for vCenter 4.x (it is high on the table). To be clear, you 902 TCP and UDP open both vcenter for hosts, host to vCenter and host to host.

  • vSphere Client does not connect

    Since today the vSphere client does not connect to one of our 3 esxi servers

    all have the same error:

    No connection available

    VSphere Client konnte keine connection "10.2.180.5" zu der recovering.

    Ein unbekannter Verbindungsfehler aufgetreten ist. (Fehlgeschlagen Anforderung ist, zu der Die da Remoteserver Hat lange nicht atmosphere.) (As procedure passed timeout))

    Translation:

    no connection

    The vSphere client unable to connect to...

    A unknown connection error has occurred... timeout because the remote server has not responded

    Ping as 10.2.180.5 ausgeführt wird mit 32 bytes of data:

    Antwort von 10.2.180.5: bytes = 32 time < 1 ms TTL = 64

    Antwort von 10.2.180.5: bytes = 32 time < 1 ms TTL = 64

    Antwort von 10.2.180.5: bytes = 32 time < 1 ms TTL = 64

    Antwort von 10.2.180.5: bytes = 32 time < 1 ms TTL = 64

    as you can see the ip address is local and the customer to the web UI works no problem but I like to use the vShpere client

    I have no idea why its not connecting

    same problem for 2 esxi in internet... from my PC at home I can connect without problems

    all ideas are welcome im really out of ideas

    some info:

    Win7 64 bit

    ESET AntiVirus 6 Endoint

    no firewall (windows firewall disabled)

    Fixed: changed to Google DNS (8.8.8.8) in-house DC DNS and everything works... really strange because I use IP to connect

  • Start the virtual machine and wait for WF, does not connect to the computer virtual for Vds (Windows 2008 R2)

    Hello

    See a strange problem with only a Windows 2008 R2 model. When you use the built-in function "Start VM and wait" workflow to start a virtual machine (after conversion from a template either manually, or through workflow) NIC of the virtual machine (I tried VMXNET3 and e1000 times) does not connect to the problem. Vds can be replicated in a different VCenter, so spreading the vds. I also created several models of Windows 2008 r2 and all have this problem.

    If the model is converted and started outside VRO, it gets an IP from and is connected to the VDS immediately

    Tried add/remove the NIC of the model

    Tried to move the comments on different hosts

    Tried to create a new template from scratch

    NOTE: Windows 2012 R2 doesn't have this problem in the same circles, the only constant is the Windows 2008 R2 being started by VRO.

    Anyone seen this before?

    I found this article and it fixed my problem VMware KB: registration or the deployment of a virtual computer model fails apparently a fix a problem in ESX 5.1, 5.5 (I used the option to get around and things are good)

  • App store, Safari and iTunes does not connect to the Internet after installing macOS Sierra

    App store, Safari and iTunes does not connect to the Internet after installing macOS Sierra

    After upgrade 'OS X El Capitan' to "macOS Sierra" window only empty "App store" and page "Safari" made its appearance, no error message shows. store "iTunes" and "Dictionary" does not connect too.

    But Google chrome works well.

    So have you tried the next steps in your original post that Safari does not work after installing macOS Sierra:

    (1) x OS: "Unable to connect" or "unable to connect to the App Store. An internet connection is required"- Apple Support

    2) Advanced the steps to correct the problems with the iTunes Store - Apple Support connection

  • Messages does not connect to the Yahoo IM account?

    Messages app v9.2, currently works very well with my Google account and iMessage, also worked with my Yahoo Messenger account, but recently (today?) does not connect to it.

    I know that Yahoo has made changes to their Instant Messaging System. This change affected only Messages?

    Hello

    I can't connect either (I didn't realize that I do not use)

    However going on the Yahoo Site and change the password does nothing.

    With the help of their option 'insecure Apps' does nothing no more (there was an email saying I was using access to messaging through an unsafe application - but I have not used their messaging service for a very long time.)

    It does say read more suggests, is not Mail (after OS X 10.9 is OK)

    He does not on access to their e-mail service.

    There is no option in Messages to try to activate disable SSL you can with AIM or Jabber accounts

    I have looked in the help (a little) but still found nothing.

    20:49 Tuesday. October 4, 2016

     iMac 2.5 Ghz i5 2011 (El Capitan)
     G4/1GhzDual MDD (Leopard 10.5.8)
     MacBookPro (Snow Leopard 10.6.8) 2 GB
     Mac OS X (10.6.8).
     iPhone and iPad (2)

  • iPhone 5 sec Bluetooth does not connect

    My 5s Bluetooth iphone works fine one day, the next day it does not connect to my Boise, helmet or Fitbit.   My Bluetooth is on, I have it enabled or disabled and you have rebooted my phone.  I have updated to IOS 10.0.2.

    I was able to pair with my ipad.

    Hello

    Try the procedure described in this article to support > get help to connect a Bluetooth device accessory with your iPhone, iPad or iPod touch - Apple Support

  • Bluetooth does not connect on iOS 10 and sierra OS

    I just bought an iphone 7, Apple Watch 2 and I updated my computer to sierra yesterday.

    I wanted to do the auto unlock with my watch, but my phone does not connect to the Mac with bluetooth. He wants to connect and the phone is displayed in the bluetooth settings, it says on my phone to pair if the numbers are the same, and then he "fails to connect. so im lost and I can't use my watch.

    I have reset my watch (by unpairing), iphone (by resetting all settings) and rebooted my computer.

    It seems that the "it just works era" is over for apple.

    If misery loves company, I'm here!  Just posted my new iphone 7 + setting BLUETOOTH is not 'discover' one of my devices (in 2015 Lexus and Bose radio/speakers).  In addition my iPad and iPad air are also not 'discover' devices!  I think that this happened once I installed the latest ios 10.0.2 software on all my devices.  Please reply if you receive some 'advice' from someone in the "know"!  Thank you!

  • I just got a new modem (Arris SB6190) and now my Airport Extreme does not connect.  It worked fine with the previous modem (a rented one TWC).  Help!

    I just got a new modem (Arris SB6190) and now my Airport Extreme does not connect.  It worked fine with the previous modem (a rented one TWC).  Help!

    Always recommended to reset the airport back to settings by default and then set up again whenever you have a new modem or change your Internet Service provider.

    Turn off the new modem for at least 30 minutes. More is better.

    Perform a hard reset on the AirPort Extreme, then it turned off.

    Make sure that the Ethernet cable connects the modem to the "O" on the AirPort Extreme WAN port

    After the power of the modem 30 minutes down, turn on the modem and let it run for at least 5 minutes by itself.

    Then, turn on the airport and let it run a few minutes

    Set up AirPort Extreme again

    Important note... There are many reports of problems with the modem Arris SB and airports. Both are great products, but they do seem to work perfectly together for some users.

  • Thunderbird does not connect with the server

    Another recent problem is Thunderbird does not connect with the server. I don't know if sent mail will go out, but I know I'm nothing receive. My internet connection works well for FF or another browser. I checked my settings and they seem OK. I checked the default settings in Win10x64 and they are correct. Any ideas?

    Although windows 10 is new for us all. How do solve you. I have other solution with very similar issues.

  • IMAP e-mail accounts does not connect

    Just recently my iCloud, Gmail and Outlook IMAP accounts does not connect through the app Apple Mail on my MacBook Pro running 10.11.6. I get a popup error message and exclamation points appear next to each account that States the unable to connect to the server application. IPhone & iPad with the same accounts are fine, just my Macbook Pro has this problem. Connection Internet is fine. Suggestions?

    Please read If you cannot send or receive e-mails on your Mac - Apple Support.

Maybe you are looking for

  • HP g4-1110TX: Audio is not perfect, with the vibration

    Hello I tried to check the audio drivers and updated their. It doesn't show any errors, the test sounds good. But when I play an audio, movie etc, I get a sound buffering. Same question comes even if I try KMP, VLC media player. Then I add 'K-Lite_Co

  • Build installer undefined error - 12 CDK_CreateNewWizard_Invoke.vi

    Search in the forum without solution for my mistake. I tried to build an installer with LabVIEW 2009 and I have each time the same error undefined-12. Here what I did: -J' made a very simple vi, build an application and Installer, the same error -J'

  • Date lack fisier XML gui

    Maryse instalez eroare apare printer; date lack fisier XML gui

  • Unable to connect the mouse Bluetooth, "network cable unplugged".

    Reformat my drive c:, Sony Vaio VGN SZ1VP Windows XP pro. Upgrade to SP3.Impossible to get Sony Bluetooth mouse works!. Have uninstalled and reinstalled Toshiba Bluetooth stack.  He sees the mouse but gives the error "failed to detect the service." 

  • Driver required message

    I'm trying to install win7 on an old Tin IDE.  Yes, win7 will run on it without problem.  I have a SATA DVD-rom connected to old Tin via USB.  The installation continues, but now I get the following message is displayed: a required disk device driver