Eve of power question (another)

Similar Questions

• Satellite L450D - weird load and power question

  Hello

  I myself L450D that plays up a little bit. The main problem with it is that it can not be activated in without the battery being inserted. Once you make this portable tension each time. Without the battery it just flashes power after light spin a fan for a fraction of a second and do nothing else.

  Most of the time, when you turn it on it will start fine but is the ' power on ' off and battery light blinks slowly (light orange). I know battery is not charging and windows says its loading in-is not clogged. After a few tries (remove and insert the back stack) when I he turned on the light "power we" and battery started to load correctly. I have the battery fully charged and it takes 2 hours (watching a movie until his real).
  The "connected" light is whenever I plug the charger.

  The questions are:
  -why he used to power up without the battery?
  -Why is not turned on on the light and reloads do not even if the laptop works well under windows?

  I tried pressing the power button for 30 seconds, with or without the battery and adapter, no luck. What is a BIOS problem? I also tried the RAM and the HARD drive in different portable, works ok.

  Also once the laptop is powered on it can go on for hours with no problems. I insist on proven components and without defects found

  Hope you can understand my ramblings, please give me a hint if you know which continues, dan

  In my opinion, you need professional help with this. On this virtual path, we can only speculate what the problem is. To me, it seems that the electronic power supply problem. I put t know what else can be responsible for this, BIOS, certainly not.

  Contact the nearest Toshiba service provider to check the electronic card. They will be able to give you answers to your questions.

• MacBook pro power question

  Hello

  recently, I replaced my battery in my macbook pro (late 2011) with an official replacement battery, I was wondering if one fell on the following question...

  almost everytime I disconnect my charger magsafe, it cuts the power rather than switch to battery power my macbook pro, I did MSC resets, resets of vram and recently diagnosed

  error code I got from the trial of the aht has been ' 4xxx/6/40000005: 0... 'battery' '...

  I'm not sure what it actually means if its my battery or battery sensor etc...

  wondering if anyone knows how to solve my problem?

  Apart from this question my mac works perfectly fine running on the power adapter

  Any help would be appreciated.

  Thank you Gary

  If you had Apple install the battery, it should have a one year warranty.  Make an appointment with an Apple store genius bar and have examined the MBP. Even out of warranty, the assessment will be free.

  Ciao.

• Acer Aspire 5750 power question

  Hi all!

  The issue started happening two days ago.  When I try to turn on the laptop, the power led lights up, the fan will start to blow, hard drive will start to spin and then everything suddenly, it turns off.  The screen remains black throughout the process.  All this happens in a period of 3-4 seconds and laptop computer repeat the process four times with attached AC adapter (with only battery attached, laptop once).  It won't start and join the BIOS, the laptop shuts down before that.   I tried several things so far.

  1 ram remove Glue one by one and replacement

  2 tried to remove the batteries and only the execution of the power adapter

  3. past autour where I used only the battery and no power adapter.

  4 taking battery and power adapter off and holding down the power buttong + 30 seconds

  5. Replace hard drive with another hard drive compatible.

  Now, I am at a loss on what to do.  Has anyone else had this type of problem? If anyone can help me, it be so awesome! Thank you in advance!

  Nice day

  You did everything possible... get the motherboard replaced.

  Kind regards

  FReeZA

• Satellite M30X-102: power question - unit suddenly turn off

  Hello!

  I have a portable Satellite M30X-102 and about a year ago and a half months he started to turn off suddenly. First of all, it looked like an overheating problem, but also disabled directly after that I pressed the power button and sometimes it worked 10 hours without any problem, also, when it is off, power LED was flashing until I have Nations United - and replugend the power cable. If the battery was, he was immediately released.

  I sent it to repairs. They only cleaned the cooler and changed the dough to thermal conductivity and for a few days, the laptop worked normally, but about half hours ago, it happened again. I am convinced now that this is a power supply problem, possibly the power cable.

  You have any suggestions of what I could do, or should I send it back with a note that it is a power supply problem?

  Thank you

  [Edited by: admin March 23 06 06:56]

  Hello

  In my opinion, you should contact the service because it can start diagnostic tests.
  For me, this looks like an electronic malfunction of power supply.
  If the laptop has been repaired it there a few days/weeks, so I guess that the guarantee is valid.

• A1: Power Question Widget

  The A1 has a power Widget that has five icons. I managed to figure out three of them, but there are two that I have no idea of their function. In order from left to right:

  WiFi, Bluetooth,?,?, screen

  The first? resembles a semicircle graduate, curves lines radiating from him (small and large)

  The second? is a circle of arrows.

  Can someone identify the buttons two mystery?

  Thank you.

  The first is for GPS.
  The second is for synchronization.

• local variables of power question

  Hello

  Attached, please fine 2 similar vi. WhileStoop.vi, I can start or stop the program at any x + y values.  But, in eventStoop.vi, I can not use stop when the program is running (program will end when x + y = 10).  Why the variable local power not working in my eventStoop.vi?

  Thank you
  Chuman

  It's a bad idea to have an event structure that contains code that takes a long time to run as the while loop inside the case in your situation.

  Probably, he doesn't stop because you have locking front panel until the event of this case ends checked.  So when you press the Start/Stop button, the same case runs and performs a while loop start running.  But because the cover is locked, it can not detect the change in power again which is necessary to stop the inside while loops.

• computer will be management option not Eve if power > 1 minute

  If the option to set power management standby after 1 minute of inactivity, it works; otherwise it is not - any ideas?

  Hello

  ·        Were you able to use watch on the system before with no problems? Since when are you facing this problem?

  ·        Remember to make changes to the system?

  Method 1:

  I suggest to update display drivers as well as drivers from the chipset on the system and check if the problem is resolved. See the article mentioned below.

  How to manage devices in Windows XP

  http://support.Microsoft.com/kb/283658

  Method 2:

  If you have set any screensaver then, it could be that the screen saver wakes up the system after 1 minute. I suggest to disable the screensaver on the system and check if the system is able to go in standby mode. Follow the steps mentioned below.

  a. press the right-click on your mouse when your desktop is visible. A menu will appear.

  b. click 'properties '.

  c. look at the tabs under the marked blue title bar "display properties". You should be able to see one marked "screen saver". Click the screen saver tab once. You should now see a small monitor.

  d. find the drop down next to the marked buttons 'Settings' and 'Preview '. Click on the arrow down on the right side of the menu drop down.

  e. look the list of available screensavers. The first menu is marked '(none) '. Click on this title. Once you have clicked on the title, the "Apply" button will become operational.

  f. click apply. Close the display properties window and the Control Panel window. You have now disabled successfully your screen saver.

  I suggest you follow the steps mentioned in the article below.

  How to solve the problems of hibernation and standby in Windows XP

  http://support.Microsoft.com/kb/907477

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.
  Visit ourMicrosoft answers feedback Forum and let us know what you think.

• Reference Dell place 11 Pro - load and power Question

  I have an i5 Vpro coming 11 Pro.  I also have the mobile keyboard. When I use them together power seems to draw everything first on the tablet.  I say mostly because the battery level drops faster than the mobile keyboard.  I searched the postings here and which seems contrary to what others have said, it is expected to be drawing from the battery first.

  If anyone can confirm this?

  Thank you!

  Mike

  I have the i5 VP11 Pro, 256 GB, 8 GB of RAM, and I use it with the mobile keyboard regularly. I am typing on right now. I can confirm that power is drawn from the keyboard first. In fact, mine will drain the keyboard up to 0% before application of the Tablet battery.

• XPS 8500 additional SATA Drive add...cable/power questions

  Nothing on sites Web of Dell (after two hours of seraching, including a chat with a Dell representative session) on how to add a hard drive from a dell computer. I'm simply confused (this happens regularly) it is difficult to find, or you really need to add a simple video on how to add an extra SATA (how many times people do that?).

  No info on cables, power supplies, how many readers you can add, etc.

  So this is the kind of thing I need... Thank you! How do I add a SATA, which cable does, esp if the slots for the cables are already taken by the BluRay player... can get a cable SATA outputs multiple?

  Thanks for your help.

  Rick Bauer

  Colorado_RBauer

  Thanks, Bev... screw seems to be the only parts I have.

  I am therefore reason to believe that I can put only two disks sata in this 8500, right? and we're already here, so I can really only add one, correct?

  Where are you going to get the good SATA cable?

  the manual referenced does not something specific on SATA wiring part I looked. Should not be too much of a pest, but do you have a specific reference.

  Rick

   
  Colorado_RBauer
   
  Rick,
   
  Yes, you can add an additional hard disk, the disk hard primary exsisting. to add several internal hard drives, you need an open 3.5"/5.25" bay and to install more than four SATA drives, SATA PCIe x 1 expansion card would be necessary.
   
  You should be able to buy a SATA data cable in a store of the local computer, or www.newegg.com for more details, go here,
   
  http://www.Newegg.com/product/product.aspx?item=N82E16812270093
   
  Better to use a local store to save the S & H
   
  Sorry to say, that the manual is the only reference that Dell has released, as most newer Dell manuals, missing many details.
   
  Install the secondary hard drive is usually relatively in line forward, you must connect the data cable to a SATA connector on the motherboard, and after installation checking the installation process, to see if the drive is recognized.
   
  If the drive is recognized in the installation program for Windows to recognize the second hard drive, it must be patitioned, formatted and received a drive letter using disk Windows 7 Manager.
   
  http://Windows.Microsoft.com/fr-FR/Windows-Vista/create-and-format-a-hard-disk-partition
   
  Bev.
   
   
   
   
   
   
   
   
   

• U3014 power questions

  Turning on my U3014 power is behaving strangely and I wonder if I need to hire a return or is there something else I can do?

  While the PC is on, if I switch the monitor off I can not switch back on except if I power cycle it.

  Even weirder, if the monitor is turned off when the PC is started, it lights, but then I can't turn off, even after it turns off the PC.

  SOTIRI,

  The monitor power cord must be connected directly to the socket while troubleshooting. Unplug the monitor all cables from the computer except for one DVI cable. Repeat the test.

• Alienware power question

  Hello

  I own an Alienware Aurora R4 with an 875 watts PSU, I plan to upgrade my GPU. East Aurora R4, SLI ready power supply? Thank you.

  Yes. But it's still only 875 w

  You can try to match the existing nVidia card for double-SLI. However, you might consider putting that money towards a new card Solution unique tip of seller as eVGA (IE 780).

• Interesting question of scrolling

  Hi everyone, I have a problem with scrolling in my area

  The page layout, I currently have is:

         vfm0 = new VerticalFieldManager(USE_ALL_WIDTH | USE_ALL_HEIGHT | NO_VERTICAL_SCROLL | NO_VERTICAL_SCROLLBAR);
          add(vfm0);
  
          vfm1 = new VerticalFieldManager(USE_ALL_WIDTH | VERTICAL_SCROLL | VERTICAL_SCROLLBAR);
          vfm0.add(vfm1);
  

  and I add a created custom field to vfm1.

  However, every time I scroll the focus passes power to another, but the screen does not scroll down UNTIL the last field wins the update. Once the last field acquired focus, scrolling further causes the screen to scroll down.

  I tried to add simple labelfields at the vfm1 and it scrolls perfectly but created custom fields are causing the problem.

  Can anyone think of what may cause this effect?

  In the custom field is created, I replace the onFocus() and the onUnfocus() but I do not see why this would have caused this problem.

  I found the problematic code.

  So the custom field I have added is horizontalFieldManager and inside, I bitmapfield

  Now, in the horizontalFieldManager I crushed focus... that makes no sense since fieldmanagers don't really get the focus (as in the past, I read in this forum).

  At the same time, I was the substitution of development for the bitmapfield as well.

  Question/bizarre and illogical behavior...

• Satellite Pro A100 PSAASE: error Power Saver and LAN? After downgrade to XP

  Hello
  I have a toshiba satellite pro A100-psaase!
  I could not find this model on the toshiba site, so I chose the A100-psaas software.

  The laptop came with windows vista. I have it downgraded to windows xp, has chosen the psaas model so that I can download the drivers.

  I have 2 problems: the first is the eve of power software, it does not work. Start windows every time I get an error in the energy saver. I can not uninstall.

  My second problem is, that a windows pop who found a network controller and I can't find any software or driver for it. So in Device Manager, an exclamation point on the icon of the network controller.

  The funny thing is that I have internet and all.
  I can't find a solution to these two problems
  Thanks again

  Hello

  You have chosen the correct unit. The satellite Pro A100 PSAASE is the same model as PSAAS.
  I put t know why the power gain error appears, but for most of these errors occur because the tools and utilities have been installed in the wrong order!
  Seems that the installation instruction has been placed on the page of the driver Tosh! Read and follow the installation guide lines! Proper installation is important and necessary.

  The LAN drivers are also published on the page! There are 2 different versions. Try them both!
  The laptop supports a Lan Intel Ekron-R 82562GZ chip. Compatible drivers, you can also find on the Intel page!

  Good day

• How to reinstall Toshiba Power Saver?

  Earlier, I deleted by mistake the eve of power of Tosh file.
  I'm assuming this command functions of STANDBY & hibernation because they no longer work, to the extent where I can not restart/recover either.
  So I downloaded the file pwrsav.xp7037i - .zip from the database of tosh, extracted, but cannot see how and where I have to re - install?
  Someone there did a similar thing and succeeded?

  I just want to see this zip file, but I just can't find no description of the model of laptop. In any case, it should be setup.exe file. Please open this file and installation should begin.