EX7000 with USB 3.0 Hub

The EX7000 (Extender/Access Point) has a USB 3.0 port. Can I use ReadyShare installation with a USB and USB printer simultaneously by connecting a USB 3.0 hub to the EX7000?

Advertisement

Hi declanb,

Unfortunately, the EX7000 does not work with a USB3.0 Hub that you described.
It is possible to use the hub with only hard drives. But the USB printer does not work with the hub.

Tags: Netgear

Similar Questions

  • IBM Thinkpad message: 'this machine can run faster with the USB 2.0 hub.

    Original title: Thinkpad USB 2.0 Hub.

    Hello:

    I have an IBM Thinkpad T-21 which is under Ubuntu & Windows xp.  I primarily use Windows XP.  The pop-up that keeps occurring is "this machine can run faster with the USB 2.0 hub.  Can you tell me how to upgrade my USB 2.0 Hub?  Would like to know because I can't sync my Android phone with my computer until I do it. Thank you.

    Are you sure you copied this error message properly?  In other words, he says that the hub could perform better if connected to a USB 2.0 port?  As far as I can determine that the T21 is not come with a USB 2.0 port, even if you connect a USB 2.0 device (for example a hub), the unit will only race as fast as the port allows it.

    What is the brand and model of your terminal?

    It is possible that the message means the opposite (i.e., your computer has a USB 2.0 port, but the hub is only a USB 1.1 device).

    USB 2.0 was introduced in 2001, so if you bought your computer before 2001, it is likely that you use USB 1.1 or 1.0.

    Open the Device Manager (start > run > devmgmt.msc > OK)
    Expand the category of 'USB Bus controllers'.
    If you see the "Enhanced" work for one or more of the listed devices, you have a USB 2.0 port.  If you do not see "Enhanced", you have USB 1.1.

    If the problem is that the USB port on the computer is not 2.0, so your only solution is to buy a USB 2.0 PC Card adapter.  Example and example 2
    If the problem is that the hub is not 2.0, then you will need to buy a new hub.

  • Problem with USB HUB using Windows 7 on Bootcamp

    I have an iMac when I installed Win 7 with Bootcamp. I have problem with USB hub. If I connect USB devices (printer, iphone... etc...) directly to my computer, it works without any problem. But if I connect them through USB hub, that they do not work properly. The sound instantly invites you, but certain peripheral functions partially and some not at all. I tried several USB hubs... same problem for all. Any solution? Thanks a lot for your answer.

    Hello

    I suggest you to see link and check.

    Tips for solving common driver problems

    http://Windows.Microsoft.com/en-us/Windows7/tips-for-fixing-common-driver-problems

    I also suggest you to contact the apple support and check.

    http://www.Apple.com/support/

  • Portege R600-140: message says: device would work better with USB 2.0

    R600-140 win 7 prof
    I plug in a device of capture usb video and a popup appears saying (roughly)

    + This device would work better with USB 2.0 - Click here for a list of usb ports.

    I thought all the usb ports 2.
    I just checked the drivers in the Panel, and I thought they are all up to date.

    The laptop supports without a doubt USB 2.0 ports.
    I guess that this message can appear for many reasons: for example the USB device malfunction.
    Also the problem of USB port could be responsible for such error.

    So as the first workaround I recommend you remove the USB hubs and controllers in the Device Manager list.
    Open the Device Manager, look for the controllers and USB hubs and uninstall the driver.
    Reboot the laptop

    Usually the system will begin to recognize USB devices.

    Note: during this procedure, all external USB devices must be disconencted

  • STOR. E partner HARD drive does not work with USB 2.0

    Hi all

    I recently purchased a 1 TB STOR. E partner HDD and it worked without any problems on my laptop Macbook Pro which has only USB 2.0 ports.

    A few days ago, the HARD drive has been disconnected from the laptop without ejecting first, and now it isn't recognized more than my laptop.

    I tried on a PC Windows with USB 2.0 and 3.0 ports and discovered that it is recognized when I plug in the port 3.0 but not on version 2.0.

    What should I do to have the HARD drive works again with USB 2.0?

    Many thanks in advance,
    Eduardo

    > I tried on a Windows PC with USB 2.0 and 3.0 ports and discovered that it is recognized when I plug in the port 3.0 but not on version 2.0.

    Stor.E partner HDD needs maximum power of my 900.
    The USB 2.0 port provides 500mA just
    If you can connect the HARD drive to two USB 2.0 ports using a USB cable in Y
    Or another option: connect a USB hub with external power supply between the HARD drive and the USB 2.0 port

  • Satellite A50 543: still some problems with USB 2.0

    Hello
    I have laptop Satellite A50 543 with Win2k SP4 installed.
    The problem is that USB 2.0 is not active.

    I found a usb device that luckily automatically installed, so I installed it manually.

    The system is now a usb 2.0 hub - root.
    If I go to properties it shows me that the usb-external hard drive is connected. So far so good...
    (the external hard drive is USB 2.0!)

    now, I copy a file from the internal hard drive to the hard drive external... and there: surprise!
    I have a transfer rate of about 2.5 MB/s
    now I really Don t know what I can do!

    thx for your help and sorry for my bad English! ;-)
    hope you understand me!

    TOBO

    Hello

    Well, as far as I know this device was shipped with a USB 2.0 and it should support a rate of 480 Mbit/s and USB 1.1 data transmission support max 12 Mbps transfer rate.
    Did you mean the transfer rate of 2.5MB/s or 2.5Mbps?

    Good bye

  • T420s + Mini Dock Plus Series 3 with USB 3.0 90W - USB 3.0 works as USB 2.0

    Greetings!

    I'm probably not the first person who cares, but I did not find the same topic in the forum.

    I have T420s Lenovo ThinkPad Mini Dock Plus Series 3 with USB 3.0 plugged 90W. The problem, I USB 3.0 port on the dock (blue) work in USB 2.0. The port of the laptop works very well. I check it by plugging Seagate drive HARD mobile - when the HARD drive is plugged into the port blue station dock Windows (7, 64-bit) complains "device can run faster", using the port laptop does not trigger the message.

    USB 3.0 is installed.

    BIOS version is 1.37.

    Drivers Intel Chipset are updated.

    Device Manager displays the connection as a chain of two "Generic USB Hub, if the HARD drive is connected to the laptop port its chain of" Renesas Electronics USB 3.0 blah - blah ".»

    Help, please! If this combination is not supported, please point to the corresponding link.

    Thank you!

    USB 3.0 port on the dock is not supported on the T420s, it is supported only on T430s and later versions.

    http://support.Lenovo.com/en_US/detail.page?LegacyDocID=ACCS-Guide

    It allows to find the document listed in the link.

    I have the T420s and T430s with this docking station.

  • Big problems with USB devices

    Since I upgraded to El Capitan I have several, serious problems with USB devices:

    1 USB hard drive: everything by watching a video from an external hard drive, the hard drive will be to disassemble all the minutes, the video will be of course hang and it takes 45-60 seconds until the drive reconnects. I also can not boot from any external hard drive more. Booting from a USB key works fine.

    2. I can't transfer my Sunny BT11 of beam data more. The Sunny Beam is a device that records the data of my photovoltaic plant. The overview of the system he sees when connected via USB, however he is not recognized and so I can't transfer data files. Also, it makes not a difference if it is connected via a USB hub or directly, the two versions do NOT work. In the Finder preferences, all devices are controlled to display on the desktop.

    The two scenarios always perfectly work with my Mac mini that has not been updated and uses Mac OS X 10.10.

    Hello Gulliver,

    It seems that if you live with loss of connection of your USB devices since the installation of Mac OS X 10.11 El Capitan, is that correct?

    I suggest that you are troubleshooting by following the steps in this article - OS X El Capitan: If a USB device does not work

    Thank you for using communities of Apple Support.

    Sincerely.

  • Satellite A100 reboot with USB

    I have a new laptop satellite A100. I installed 2 device (modem ADSL and Webcam).
    I can't reboot my pc with the device, because I have a black screen. The hard drive does not work,
    and SO does not start.
    SO, if I reboot reboot without device, start corretely.

    Can you tell me why? and what I have to do?

    Thank you.

    Hello Pippo

    I noticed the same thing. If the USB memory key is attached to the unit needs a lot of time to start. Once I wait about 20 minutes, but if I remove the key USB the unit will start immediately.

    Believe me, that I tested it with four different Toshiba notebooks and everywhere that I got the same result. I put really know why this is happening but maybe you can try to use the USB hub with own power supply.

    Satellite A100 is a fairly new unit and I don t think that there is a problem with the operating system. The fact is that all the USB ports don't external devices of t with the same power supply. Sometimes may happen this work one device on a port USB port but not if you are connecting to another.

    As I said, you can try with USB hub.

  • USB 3.0 detected as USB 2.0 hub

    I want to add USB 3.0 ports to my laptop (Dell 1545, running Win7 with all available updates).

    I installed a Renesas ExpressCard with two USB 3.0 ports.  This map features well uses the drivers of Renesas that accompanies it.  The Device Manager lists as a hub USB 3.0, and several external HDs that have USB 3.0 interfaces work fine when plugged in it.

    Now, I need to have more USB 3.0 ports available on this laptop for other equipment.

    To do this, I bought an external USB 3.0 hub generic (unknown manufacturer, 7 switch ports and a power adapter which provides 5V @ 2A power supply by bus).

    No drivers have been provided with the hub, in fact, it has been announced as not requiring any because Win7 had already installed the necessary drivers.

    I plugged the external hub in one of the ports of the ExpressCard and Win7 has recognized, but only as a USB 2.0 hub.  All devices I've tried on the external hub worked OK, but only at USB 2.0 speed.  Device Manager displays the Renesas USB 2.0 external hub as a hub, and it uses the same driver (Renesas v3.0.16.0) as the ExpressCard.  When you try to update the driver, Win7 says it's the best driver available.  I've considered uninstalling the driver of Renesas and tries to install a driver Win7, but I don't know if it works or if it would affect the ExpressCard.

    If anyone has any ideas on this, I would appreciate hearing them.

    Jerry

    Hi Jerry,

    This problem may occur because of conflicts between the towing devices (Renesas ExpressCard and Generic USB 3.0 external hub). It could also be a USB 3.0 adapter generic defective as external devices detect USB 3.0 when it is connected to the ExpressCard of Renesas, in which, they are not connected to the generic adapter.

    To learn more about the issue, I you suggest to disconnect the ExpressCard Renesas and then connect the Generic USB adapter only on the computer. Make sure these devices are getting detected as USB 3.0 device. In addition, when you connect the USB adapter to the expresscard, make sure that you have connected to the USB 3.0, rather than a USB 2.0 port. If the problem persists always, so, you can contact the manufacturer of the Generic USB adapter.

    For reference:

    http://blogs.msdn.com/b/usbcoreblog/archive/2012/06/27/how-to-determine-whether-a-USB-3-0-device-is-operating-at-SuperSpeed.aspx

    Please let us know if you need more help on the issue.

  • Problem detection IOGEAR GUH285 USB 2.0 hub

    I just bought this 2.0 hub 4 port USB of IOGEAR (model GUH285). This is supposed to be a plug-and-play hub. Infact, if I connect it to my other computer with windows 7, it works fine. But on this one (Windows 7 too), it's not!

    In PC-1, where he works, it does not install any software device driver. It works and is listed under USB controllers in Device Manager.
    In PC-2, where it does not, it's trying to install a software device driver and it fails. If I look in the Device Manager, it lists under other devices-> hub USB 2.0 with a yellow sign at the front. If I try to update the driver and then manually select the location one or C:\\Windows\Drivers, it can't find it (my assumption was that it takes a generic player already installed on PC - 2 is on PC - 1). I contacted the manufacturer, but they say it should work like him for the other PC running the same operating system windows 7. Can someone help me please.

    by the way, I got it works... had to install manually the usb hub root for her... but now there is another problem... my usb for mouse Logitech M305 wireless receiver would not work with her. Other things attached to the hub as a Western digital external drive, USB in Kingston, dell etc USB keyboard key work perfectly well. Only problem is with the USB receiver. If I connect the M305 usb receiver to the hub, it will try to install a device driver and invariably fails and it lists, as previously, under "other device-> usb receiver" in Device Manager. But if I connect the M305 usb receiver to the other free usb port on my laptop directly, it works very well and it lists as composite USB device. I can see that the driver is 'C:\Windows\system32\drivers\usbccgp.sys' when it is listed as a device composite usb plugged into the USB port on my laptop. It is just plug and play in this case. Is there a way I can manually install this driver specific to the M305 usb receiver when it is connected to the USB 2.0 hub? Hope that I have understood the question.

  • Got a 27 "monitor from Apple, with thunderbolt (error). My MacPro can't love at first sight. Apple won't bring back the monitor. Will using a USB 3 map and then using a hard drive with USB 3 and Thunderbolt works?

    Got a 27 "monitor from Apple, with thunderbolt (error). My MacPro can't love at first sight. Apple won't bring back the monitor. Will using a USB 3 map and then using a hard drive with USB 3 and Thunderbolt works?

    N ° you need a computer logic board which has built in Thunderbolt.

  • With USB ports surge protectors

    I have an iPad 12,9 Pro.  I noticed an increase in surge protector Strip with USB connections available in stores.  Is can I charge my iPad Pro by directly connecting the charging cable into either of the USB sockets on the power strip to the surge protector?

    Perhaps, but it will be probably cool more slowly than with 12 Watt charger, it came with. Compare the 2.4 output amplifier with current available from one of these ports of surge protector.

  • can't get out with USB itune icon

    using ipad unable to leave the itunes icon with USB showing

    Hello, Conmare.

    Looks like your iPad slipped in for some reason Recovery Mode any. Which indicates something happened and you will need to reinstall the iOS. I'll be happy to help you with this.

    If you see the connect to iTunes on your iPhone, iPad or iPod touch screen

    Connect your iPad using the lightning cable provided with your iPad to a computer with iTunes installed on it and see if iTunes responds. If so, that's fine! Just follow the guests.

    If iTunes does not respond, disconnect the iPad off the iPad by using button on/standby (power). Once it is off, press and hold the Home button and reconnect the iPad to the cable. Don't release the Home button until iTunes responds. Still, if this is the case, follow the prompts.

    Once iTunes has reinstalled the iOS again, you can use a recent backup, as you did to reset your iPad. If it is not all recent backups, configure as a new iPad and sign in iTunes and App Store and iCloud. You can synchronize the information that is available. Another thing, I'm afraid, is lost.

    Nice day!

  • Course speed SSD at 40 MB/s with USB - C cable

    I recently bought a Samsung T3 USB - C SSD drive for use with my MacBook.

    But right now I am facing a problem of course speed on that:

    I bought it used with my MacBook retina 12' because of the support of USB - C

    But there is a real problem for this drive to use with cable USB - C for USB - C:

    If I use the USB - C to C USB Apple cable, I get only speed USB 2.0 which is capped at 40 MB/s in and out. As the 1-3 photo shows below.

    If I use it with USB - cable USB - A C I USB 3.0 speed of 425 MB/s 400 MB/s on. But the downside part is for MacBook, I use a USB - C for the USB - A adapter as shown in photo 4-6.

    If Apple is any course speed cable USB - C or Samsung should take the blame that send the wrong information of speed USB 2.0 for Macbook?

    Use with direct cable Apple USB - C (I tried another cable USB - C like same problem anker/Chotech) cable is not the problem

    You can see that the speed in the information system is listed as USB 2.0 at 480 MB/s

    A speed test to confirm it is limited to the USB 2.0 standard:

    If I use a USB to adapter USB - C and use the USB - C for cable USB - A on the SSD. It will run at full speed:

    You can see that the speed in the information system is listed as USB 3.0 to 5 Gbps

    A speed test confirm this works:

    The USB - C to C USB cable that comes with the MacBook is not supposed to be used for data, this is to be able to only. You will need to buy a USB - C data cable.

Maybe you are looking for


HashFlare