Explorer.exe error in the ntdll.dll module

Similar Questions

• Explorer.EXE error after the restoration of the ERD Commander

  Dell Inspiron B130

  Windows XP Service Pack 2

  Recently performed a HD format and new installation of XP SP2. After I installed all the drivers and others, I checked that the system was operating normally. After a few days of use, Windows Update downloaded Service Pack 3 and asked me to install. I started to install SP3, but at about 50%, the laptop battery is dead at Midway through the installation. I plugged the laptop on the power source and power. I restarted the laptop and XP started only a completely black screen and the white slider. No ALT + CTRL + DEL, desktop icons, etc.

  I rebooted the laptop of ERD Commander, ran the restore system and selected the first available Restore Point. Point of restoration chosen was recorded a few days before, and was the first recorded point after the clean installed XP. I rebooted the XP system. Wallpaper loaded with white cursor, but NO start menu or desktop icon. A message appears saying "Explorer.EXE Application error, press OK to exit the application" or something very similar. Did not write the error code, but can get if necessary. If I press the OK button (which is my only option), there is still no icons on the desktop or the start menu. Only the cursor. No access ALT + CTRL + DELETE or something like that.

  Thinking about completely wipe the system and reinstalls the operating system. Any suggestions before I jump in this solution?

  Explorer.EXE error after the Restore Point of ERD Commander. Dell Inspiron B130. Recently clean installed XP SP2 on laptop. Installation of SP3, to 50%, battery dies the laptop right in the middle of the installation of the SP3 update. Restarted, XP starts with black screen with cursor only. ERD restart order and restore XP to the last known good config (I choose point immediately after XP clean install). Reboot to XP. Now the wallpaper shows as well as the error message saying "Explorer.exe Application error, click OK to exit Explorer" dialog and then I can't access anything. Any ideas?

  Hello

  What is the full and exact error message?

  Step 1: Check if you are able to boot into safe mode without any problem. If you are able to boot into safe mode without any problems then try to perform the clean boot to safe mode. Also disconnect any external devices connected to the computer.

  Reference:
  To start the computer in safe mode
  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/boot_failsafe.mspx?mfr=true
  How to configure Windows XP to start in a "clean boot" State
  http://support.Microsoft.com/kb/310353

  Step 2: If you are still having the same problem, then you can the steps at the bottom of the article.
  How do I recover from a corrupted registry that prevents Windows XP startup
  http://support.Microsoft.com/kb/307545

• Explorer.exe hangs in the shell32.dll file

  When I right click on the directories in Windows Explorer, the Explorer stops and restarts.  This only seems to happen when I right click on a disk or a file, just a directory.  Here is what I get in the event viewer:

  -

  -

  1000

  2

  100

  0 x 80000000000000

  42890

  Application

  Ethan

  -

  Explorer.EXE

  6.1.7601.17567

  4d672ee4

  Shell32.dll

  6.1.7601.17678

  4e5c71cc

  c0000005

  0000000000050520

  EE0

  01ccd86ad5fa6e50

  C:\Windows\Explorer.exe

  C:\Windows\system32\SHELL32.dll

  2d107770-445e-11E1-8401-0026184c447d

  Here is what I tried:

  1. I booted in safe mode and it happened again

  2 ran sfc/scannow, with a result "Windows Resource Protection has not found any breach of integrity."

  3. I have an up-to-date anti-virus (Norton 360) and it has not detected a virus.

  This has happened for a while, and I have not associated with any particular software installation.

  Thank you

  I'll have to reopen it.  The solution I had not worked.

  I made a mistake, because I was clicking on a different place.  For some reason, I started clicking in the other pane.

  I have a new symptom to describe... This happens only in the left pane of Windows Explorer. I can right click on a folder in the pane on the right, on the desktop, anywhere, but the left pane.

  Hi the Geek Cruiser

  You should continue to use ShellxView to locate the bad Manager context menu management.

  In ShellxView, in the toolbar, select Options and click on the type of the extension element filter.

  This will show that the elements of context Menu in the main window.

  From there, it is simply a matter of disable context menu items and test results in the left pane of Windows Explorer.

  I recommend you to disable all elements of third in the list to begin. Look in the columns of product and company name to identify these third-party extensions. Select one and then hold down the Ctrl Key and select others.

  Log off/log and the results of the tests. If the problem has disappeared, then you know that the culprit is in this group that you disabled.

  Turn on half of this group and test again. If the problem reappears, then you have reduced to the group that you enabled.

  Then, off the half of the second group and test.

  Continue this process until you find the culprit.

  You can find that in many cases you are not yet using third-party shell extensions and you can let them simply disabled.

  Tell us what you find.

  Concerning

• Explorer.exe error of Application the Instruction at '0x7c910ed2' referenced memory at 0x03ede088.

  always get this when I try to open certain files? any suggestion will be good?

  Explorer.exe error of Application the Instruction at "0x7c910ed2" referenced memory at "0x03ede088", the memory could not be 'read' click OK to terminate the program, click CANCEL to debug the program

  I also have error of Application Explorer.exe the Instruction "0x7c911689" referenced memory at "0 x 04180000", the memory could not be 'read' click OK to terminate the program, click CANCEL to debug the program

  Good.

  Not sure what it is yet, but you know what it is not.

  I don't know what to think of your permissions problem, but if records are read-only and not meant to be, are you not able to change the folder properties and what happens when you try to do?

  When the Windows Explorer (not Internet Explorer) is wrong (especially when right click), begin to suspect third-party add-ons explore extension.

  Those who would be the Explorer extensions that do not belong to Microsoft.  This means that extensions that you have added.  Solution Explorer extensions are generally well and installation of certain applications will install extensions from Explorer solutions for you, give you a choice and sometimes they can be added without your knowledge when you install the new software.

  Solution Explorer extensions are sometimes added as a new right-click option, you see on folders and files (like the scan of this file, open that file, play this song).

  If there is something in particular that you do during exploration that you know will be the cause of the problem, which will help focus on the problem and the help that you suddenly know, when you have found and corrected.  If you can get there when you want it, make an adjustment and then there is no message the next time you don't do anything, you do, you have found and corrected.

  First of all you need a way to see what modules explore you have installed now and a way to turn them off (not uninstall them) so you can understand that we are at the origin of the problem.  You can have a lot of extensions not installed Microsoft don't even know you about.

  Download ShellExView here to see what Explorer extensions you have loaded:

  http://www.NirSoft.NET/utils/shexview.html

  ShellExView does not install anything on your computer, simply of runs and displays.

  After launching ShellExView, under Options, choose "Mark non-Microsoft Extensions" and extensions not Microsoft will be pink, clear, but on some systems which is a difficult color to see, so click on display, choose the columns and move the column Microsoft closer to the top, so you can see on your screen without having to scroll left and right.

  Click on the column header for Microsoft sort display (by clicking on the column of Microsoft) then all the non Microsoft extensions are on top and easy to see.

  Non-Microsoft extensions would be things you have added (non-Microsoft) and are what you should be suspect.

  You can also Google the name of a suspect add-on and see if there is any success on the mistakes of the DEP and what other people have done about it.
  You can Google something like:

  Explorer XP crashing (you must fill in the name of add your suspect on.)

  See what kind of search results hits you get and are looking for solutions or situations that sound like yours.

  I'm not a defender of trial and error, but I can't think of another way to do...

  Right click and disable the non Microsoft extensions one at a time (or maybe in groups of 3-5), keep a list, so you can enable them again later if you wish. The result of the change is immediate and no reboot is necessary.  Test your failure condition.  If the Explorer starts to act normally, you'll know that some extension you just disabled in this group of 3-5 is the culprit, then you can start to enable them one by one until the Explorer fails again.

  If you recognize all the extensions that have been added or recently downloaded, start with these first.

  Disabling the extension does not uninstall the extension - it is just disabled.

  Disable them one at a time or in small groups (to make things go faster) until your right click does not generate an error, and then restart and try again.  You have disabled the last extension would be suspicious.

  You can also just disable all non-Microsoft extensions, restart and allow them one at a time until you find the one that generates the condition.

  If you have a large number of extensions, you can disable them is small groups, 3-5 at a time instead of 1 at a time until your system starts to behave.  When it does not, you will know that the problem is one of the extensions of this small group and you can enable members of the Group at a time until the problem returns, then the problem is with the last extension that you enabled.

  The hope is that you will find an extension that caused the error, and then you can figure out what on this subject - either uninstall it or see if you can get an update of the author of the extension of their web page.

  I have not your problem, but I can when you toggle extensions, the extension is immediately disabled, so disable an extension does not seem to require a restart, but if you think that you have found the problem, I reboot and repeat the test in any case to be sure the problem disappeared.

  If you post your non-Microsoft extensions list, maybe someone will recognize it as a potential problem.

  If you find the offending extension that's the problem, please let us know what it is that I can add to my list.

• error at startup after virus cleaning: "!" Office could not load or run 'explorer.exe' specified in the registry. "

  Original title: Tidying to the top of my desk after riding it a virus

  After cleaning after infection by the virus qqlog whenever I log in, I get an error message; " ! Office could not load or run 'explorer.exe' specified in the registry. Make sure that the file exists on your computer or remove the reference to it in the registry.  Explorers of two Windows Open C:\. And when I close the first error an another explorers of five Windows Open C:\.  Basically, I still have to do, but don't know how. Apart from the slowness of opening no other problems. Can someone give me help please.   Thanks Andrew

  Make sure you have backups of all important data for you (Favorites/internet Favorites, music, photos, documents, spreadsheets, presentations, drawings, numbers of series and product keys and installation to start with media) as soon as POSSIBLE.

  Format and start from scratch OR use the 'Restore Factory default' the manufacturer can give you.  Your stuff of restoring a backup after installation of your spplications on the machine.

  Why?  If this system is still messed up after cleaning a virus/trojan/worm/spyware/adware/malware - it may have to discover/waiting more moving and / ore actually operate 100% may take longer to restore to the Virgin (not to mention you can never achieve 100% otherwise.)

• STOP: c0000221 Unknown Hard Error\Systemroot\System32\ntdll.dll

  I have a Dell Vostro 1500 running Windows XP Home edition.  During the Windows boot the system falls down and shows the error in the title above. I replaced and improved hard drive and modules memory live with Dell components and tried to launch the system to start disk.  Same result screen, blue with the unknown hard Error\Systemroot\System32\ntdll.dll STOP: 0000221.  Then new hardware configuration and system bootable drive equals the same result.  Any advice will be appreciated.

  Thank you, everyone, for all the good advice and help. Interestingly, I used a reinstall drive different (one for the same version of Windows XP SP2), and it worked fine. I think this would indicate that the original disk could have been the cause of the problem, but I tried to install the operating system with this drive just to be safe, and it worked. It should be noted that I did no changes to the machine until I tried the new disk, then retried first that I tried to use to reinstall the operating system. This suggests that, regardless of the problem, he don't has not been caused a constant problem.

• Explorer.exe error

  Hello

  I have HP Pavilion e002au laptop bought about 5 months back with Windows 8.

  I get the explorer.exe error after logging in each time. The laptop seems to work normally, but can someone please tell me what this error is and how it can be eliminated?

  I have an original version of Windows antivirus updates and get regularly.

  Is it dangerous for the laptop?

  Kind regards

  Vikram P. Gupte

  Hi Vikram6880,

  During the execution of any type of control system, you should always back up your documents. The update affects all documents. It was simply an update of the system.

  Thank you.

• Explorer.exe stops when the computer is shut down

  Explorer.exe stops when the computer is shut down

  Hi DickKimberley,

  ·         What exactly happens when you try to shut down the computer?

  ·         You receive an error message error code?

  ·         Did you do changes on the computer before the show?

  Follow the suggestions below for a possible solution:

  Method 1: I suggest you to consult the article in the Microsoft Knowledge Base and check.

  Advanced Troubleshooting for shutdown problems in Windows XP

  http://support.Microsoft.com/kb/308029

   

  Method 2: If the method above doesn't follow the article mentioned below.

   

  Windows stops responding during Windows XP shut down

  http://support.Microsoft.com/kb/307274

  Let us know if that helps.

• We get answerSTOP: c0000221 Unknown Hard Error\SystemRoot\System32\ntdll.dlls

  My Dell crashed.   When I try to restart, it will start not (in any mode): can't go in Safe Mode or last mode of work or other.   I managed to get to the blue screen and I saw the following: STOP: c0000221 Unknown Hard Error\SystemRoot\System32\ntdll.dll

  I did some research that says I can try to reinstall / Windows XP Recovery and that this could make it work
  I have all the original disks.
  Can I use the Microsoft XP disk and how can I reinstall without wiping my hard drive (I'm terrified by wiping my hard drive)
  The manual of Dell said to insert the Windows XP installation disk and I have the ability to REPAIR, not REINSTALL
  Will this work?
  Another site indicates that the problem is that the drivers are up to date...  I can't update because the PC is not connected to the internet
  Help, please

  Hi Niallmcardle,

  I suggest you follow steps from Microsoft Knowledge Base article and check if it helps.

  A Stop: 0xc000026C or Stop: 0xc0000221 "Unable to load device driver" error occurs when you start Windows XP

  http://support.Microsoft.com/kb/315241

  I hope this helps.

• LabVIEW FPGA: An internal software error in the LabVIEW FPGA Module has Unknown

  Sir/Madam,

  Note Labview 2012 SP1 installed about 2 weeks ago.,.

  Accident occurred during the compilation of an fpga vi who worked satisfactorally in the past.

  When I restarted and went to the message recomplile "LabVIEW FPGA: an internal software error in the LabVIEW FPGA Module" see attached picture of popup.

  I reinstalled Labview in its entirety and backed out the changes I made to the vi but still get the same message.

  Thanks in advance

  Daryl

  It turns out that the question was in the VI and not of LabView FPGA module as the message may indicate. I created a vacuum vi, cut and pasted items in this from the vi error and recompiled and it ran very well.

  Somehow the vi has been corrupted internally.

  Thank you it's fixed.

• Explorer.exe error, Normaliz.dll is missing

  When I try to start my computer, I get the above error. I get the same when starting in safe mode. The only thing that works is the Task Manager. No desktop icon just a white screen. Where should I start

  In Task Manager, you can click file, hold down the CTRL key, and click New task and that opens a command prompt (or the boot safe mode with command prompt).

  If you have your copy of normaliz.dll on a USB key which is the D drive (for example), and XP is installed on your C drive, you can then type in something like this:

  Copy d:\normaliz.dll c:\windows\system32

  When the copying is completed successfully, you will see a message like:

  1 file (s) copied

  You can always do since if Task Manager:

  If you see a message like this:

  Explorer.EXE - unable to locate component: this application has failed to start because Normaliz.dll was not found. Reinstalling the application may fix this problem.

  It is in the case Log:

  Event type: Information
  Event source: Application Popup
  Event category: no
  Event ID: 26
  Description:

  Application popup: Explorer.EXE - unable to locate component: this application has failed to start because Normaliz.dll was not found. Reinstalling the application may fix this problem.

  Start explorer.exe, but the normaliz.dll file.  If explorer.exe is not able to run, you will not be able to do much with your system until the replacement of normaliz.dll.

  You can click OK for errors and finished up in the Task Manager where you can try to fix it.  The message can keep popping up from time to time, while you're fixing it, so just click OK to close the message.

  If normaliz.dll is missing, you can copy it from a working system to the system afflicted with the same version of XP and Internet Explorer.

  You will get a good copy and put it on a floppy disk, thumb drive etc and copy it to your system plagued by using Manager tasks.

  The normaliz.dll file must be located in the c:\windows\system32 folder and therefore is not a Windows file protected, making the Microsoft Support Engineer 'experts' suggest running sfc/scannow, which is just another one of their prosecution of wild goose that will not work, he'll never work and it will only waste your time (and they don't tell you how to run either - if explorer.exe does not start).

  Then engaged Microsoft Support Engineer 'experts' will offer to you develop a copy of the file from the XP installation CD you probably haven't, but it is also not on your XP installation CD, and you will have the same problem try their suggestions to 'try' to start in any any Mode without failure, so this will not help you.  These "experts" seem to think that the Safe Mode boot or boot will replace magically missing files, but it doesn't.

  You also will be able to properly run a browser on the system afflicted to go on Internet download one.

  There is a large computer security risk in the normaliz.dll from some website download.  The best idea is to get a copy of normaliz.dll from another computer that has the same version of XP and IE and replace it from a USB device (which you can access from the Manager tasks), or using a system that works, you can download one of my SkyDrive.

  You can still use the Task Manager to run the system restore and bring it back, but I've never tried and never use SR in all cases.

  If you have recently done a bunch of Microsoft updates, you may have also gotten IE8 so maybe that something was wrong here although the normaliz.dll is the same for each version.

  When you see the error, you can click beyond it and eventually arrived at your screen background image where you can press CTRL-ALT-DEL to start Task Manager. TM, you can click file, new task, Browse and edit the menu drop-down "Files of type" to all files that you can see all the files in folders.

  Go to c:\windows\system32 to see if normaliz.dll is really missing. If the error appears again while browsing, just click OK to get past it.  The explorer.exe tries to run and cannot until the missing file is replaced.

  If it's the only thing missing, you can get one from a working system of the same type as yours, copy on a Flash DRIVE or a floppy disk and always using TM, to browse, copy and paste it where it should be or you can download one of my SkyDrive.

  TM, you can still access your thumb or any other medium the same disk by navigating, copy, paste, etc very well all work.  You use TM to navigate to your thumb or floppy disk, copy the normaliz.dll good and then paste it in the c:\windows\system32 folder, where it is supposed to be.

  If things get worse, just return to TM and remove the file back where you were in first place and continue troubleshooting.

  Using a system that works, you can also download a copy of the file from my SkyDrive and put it on a floppy or USB thumbdrive and networks diskettes for the distressed system.  Sandalenet means wear you the system afflicted by hand.

  I downloaded a copy of XP Pro SP3 file you need on my SkyDrive (everyone has a SkyDrive for file sharing).

  You can download it and when you do, place a copy of the file in these two folders (assuming that Windows is installed on your C drive):

  c:\Windows\System32

  Here is the link to my SkyDrive and you can get the file you need here:

  https://SkyDrive.live.com/?CID=6a7e789cab1d6f39&ID=6A7E789CAB1D6F39! 311

  When you see the files available for download, you can not see the file extension (.exe, .dll, .cpl, .sys, .zip, etc.), but when download you them they will have the right extension.

  When you download the file (especially if you use Internet Explorer), when you get a chance to save the file, your browser is unable to save the file with an extension (by example, .exe, .dll, .cpl, .sys, .zip, etc) then you will need to manually add the extension appropriate to the file when you download the file before you save it.

  You can download the file without the extension, and then rename the file to add the appropriate extension.  You do not want to use a file called normaliz when the name of the file should really be called normaliz.dll (if the downloaded file has no extension, you will need to change the name of the file to add the appropriate extension to make it work.

  You then put the downloaded files in the correct folders on your system.

  That may not solve all your problems, but at least you will be spending this part and we can then fix the rest.

• Explorerframe.dll and Explorer.exe errors

  After receiving an update of windows, when I tried to start windows (I have dual boot with linux), I was given an error for "explorerframe.dll" and had to shut down my pc. I managed to fix explorerframe.dll and when starting windows for now, I was greeted with the error for explorer.exe does not. After doing a sfc/SCANNOW, I solved the problem, but to try to connect again, I was told that explorerframe.dll did not work properly. It is as if I am stuck in a loop with a work, then the other is not. If someone could help with these questions, I would appreciate the help.

  Follow these steps only thino you can do now is try to replace Explorerframe.dll.

  1.step- Run the command prompt(make sure that you run as administrator)

  2.step -in CP to enter this command takeown /f explorerframe.dll

  step 3- now we must find explorerframe.dll.Press Windows key and E, when you open my computer to high right field looking for explorerframe.dll

  -4.step Right-click on explorerframe.dll, go to Properties, go to the Security tab, click your user name, click CHANGE , and then select full control

  step 5- if you have Win7 64 bit make sure that u give full control to the explorerframe.dll in SysWOW64.

  6. step- you can now download and replace explorerframe.dll.

  If you are using WIndows 7 64-bit do the same for the explorerframe.dll in SysWOW64!

  If you can't find DLL download, send me message private so I download mine.

• Explorer.exe error of Application the Instruction at "0x715ba067" referenced memory at "0x715ba067". Memory could not be "written".

  Hi... I get this every time I try to open a specific application in my system. Could you please suggest how we can avoid this error message. Thank you.

  Hi dieng,.

  To provide the proper resolution, I would need more information on your side.

  1. What is the name of the application?

  2. were you able to open the application before?

  This problem may occur because of corrupted system files, or if the latest Service Pack is not installed.

  Method 1:
  I suggest you to refer to the article and try the procedure described in the article. Check if it helps.

  Explorer.exe may generate an application error when you close a folder
  http://support.Microsoft.com/kb/329692

  Method 2:
  If the problem persists, I suggest that you run SFC [System File Checker] scan on the computer.

  SFC scan will scan system files corrupted on your computer.

  Description of Windows XP and Windows Server 2003 System File Checker (Sfc.exe):
  http://support.Microsoft.com/kb/310747

  Hope this information helps. Answer the post with an up-to-date issue report to help you further.

• LabVIEW Application Builder Crash: ntdll.dll module failing

  Hello guys,.

  I am currently having problems during the construction of my project (LV2012 (32 bit), Windows 7). At the end of the application generation, LabVIEW crashes without explanation (screenshot in french, sorry)

  

  Following Windows errors logging:

  Event 1000 Application Error
  
  Faulting application name LabVIEW.exe, version : 12.0.0.4024, time stamp : 0x4fea600e
  Faulting module name : ntdll.dll, version : 6.1.7601.17725, time stamp : 0x4ec49b8f
  Exception code : 0xc0000374
  Fault offset : 0x000ce6c3
  Faulting process id : 0x16fc
  Faulting application start time : 0x01cda5350f41f87c
  Faulting application path : C:\Program Files (x86)\National Instruments\LabVIEW 2012\LabVIEW.exe
  Faulting module path: C:\Windows\SysWOW64\ntdll.dll
  Report Id : 8e5b1344-1128-11e2-97d8-c0f8dae81bad
  

  I had the same problem on LabVIEW 2011. I tried to create my application with another computer (also LV2012 32-bit) and Windows 7 64 bit and I have no error.

  What is the problem with my computer?

  For french, french subject people

  Thank you for your help,

  Kind regards

  Quentin

  Solution found:

  -Uninstall all products of OR

  -The keys to clear registry associated with LabVIEW

  -Remove the directory of National Instruments in Application Data

  -Reinstall LabVIEW

• Explorer.exe error black screen

  Hello
  I have to tell you all that I am not good at tech or computers, so please bare with me.
  My drive has been recently cleaned. I restarted my pc and I got an error "explorer.exe application error".
  There is also an error in dll C:\Windows\system32\WerConCpl.dll
  My screen is black, however, I can use internet through the Task Manager.

  When I tried to find explorer.exe in Task Manager, the error message came again. He can't run the application because it could not start properly.
  Any advice?
  Thank you.

  Hello Alex,.

  We are here to help.

  Explorer.exe application error may be similar to Windows Explorer has stopped working. You can follow the steps of troubleshooting provided on this link.

  You can also run repair.

  Let us know how it goes.

  Thank you.