Express the guard cover lost drive

Similar Questions

• Satellite L70-A-139 - guaranteed zero when removing the cover for the RAM and HARD drive

  Hi all

  I have a Satellite L70-A-139 youcef.
  And at the back of the laptop, there is a cover that is fixed with a screw.

  Wil I void the warranty when I unscrew and take a look?
  I want to upgrade my HDD to SSD.
  The motherboard supports Sata III: D.

  Thank you!

  No, the mandate must still be valid.
  There is a removable cover at the bottom of the unit as shown here:
  [Toshiba Satellite C70 / C75 / C70D / C75D / L70 / L70t / S70 / HARD S70t drive replacement procedure | http://aps2.toshiba-tro.de/kb0/CRU3703HG0000R01.htm]

  Then you should be able to upgrade the RAM and HARD drive.
  I think this info should be mentioned in the user manual too.

• My mouse wireless guard saying lost connection.  I thought that it may need a new Bluetooth card.  An idea of the cost if I do it?

  My mouse wireless guard saying "lost connection".  It takes time for it to reconnect.  Wireless keyboard is OK.  Apple store said that it may need a new Bluetooth "card."  Any idea the cost if necessary.   I tried a new mouse, with the same results.  Having to use a "wired" mouse now taking a much-needed port on my iMac.

  I return to the store and get a better answer. Material, of course, could be the problem. As far as I know, there is no such 'map '.

  Reset the PRAM and SMC... can't hurt, might help.

  Barry

• How to remove the rear cover to the hard drive.

  I own a laptop, a HP Pavilion dv6, System ID 3583, product ID LY076UA.

  When you turn on the laptop hard disk cover has no screws, it seems to be stuck in the chassis. What to do, take a knife and try to lift up?

  All the diagrams that I find slightly different models shows screwed on covers HD online.

  I also need to replace the fan, I would not mind a maintenance manual appropriate.

  Hello

  This is the HP Pavilion dv6 Maintenance & Service Guide. There's a latch of service you must release to access with the optical and hard drive. This is why there is no screws.

  

  

  Best regards

  ERICO

• Recently, I deleted my partition bootcamp about 65 GB space. However, after that I restarted my MAC, the 65GB is lost! The total space in my HD is currently 434GB although it should be 500 GB! Anyone know how to recover my space 65GB?

  Recently, I deleted my partition bootcamp about 65 GB space. However, after that I restarted my MAC, the 65GB is lost!

  The total space in my HD is currently 434GB although it should be 500 GB! Anyone know how to recover my space 65GB?

  See below for my disk utility:

  

  

  Hello waynetay,

  Thank you for being part of the community of Apple!

  Looks like you want to recover the hard disk space that has been used by Bootcamp.  I know how critical disk hard space is, as I understand it want to access it.

  The Boot Camp Assistant should have added space on the side of Mac OS X from the hard drive when it has been used to remove Windows.  Since that didn't happen, you need to back up the system, and then erase the hard drive, then restore the backup.

  First, back up the computer.  Your computer has software called Time Machine.  It is a fantastic software for backing up your computer.  Information on how to use Time Machine is available here:

  Use Time Machine to back up or restore your Mac.

  Once you have the backup, you must erase the drive and then restore the backup Time Machine.

  You can use these measures to erase files on your startup drive and install a fresh copy of OS X:

  1. Before you begin, make sure that your Mac is connected to the Internet.
  2. Restart your Mac. Immediately hold down the command (⌘) keys and R after having heard the startup sound to boot into OS X Recovery.
  3. When the recovery window, select disk utility, then click on continue.
  4. Select the volume name back from your startup disk in the left side of the disk utility window, then click Delete.
  5. If you want to erase the disc safely, click Security Options. Select an erasing method, and then click OK.
  6. On the Format menu, choose Mac OS extended (journaled). Type a name for your drive, and then click clear.
  7. After that the drive is deleted, close the disk utility window.
  8. If you are not connected to the Internet, select a network in the Wi-Fi menu.
  9. Select the option to reinstall OS X.
  10. Click on continue and follow the instructions on the screen to reinstall OS X.

  Once OS X installation is complete, you should have the option to restore from a backup Time Machine in the first installation of OS X.  Choose this option, and the computer will restore everything that was on it before it has been removed.  More information can be found here:

  How to reinstall OS X on your Mac

  Have a great day!

• 2015 envy 17 t-n100 I76700HQ: how to remove the back cover of a 17 t-n100 envy?

  Hello, I upgrade my Ram and hard drive 16 GB of Ram and 1 TB ssd drive. I looked everywhere, but for the life of me I can't find any info on how to remove the back cover. There are utube videos that show older versions, but they are completely different. You can provide any help would be greatly appreciated.

  Thank you

  Hello

  Did you know that it's a job for parts of authorized service provider ? If you wish, for the RAM, try it please:

  1. turn off the computer. If you don't know if the computer is off or in hibernation, turn on the computer and then stop it through the operating system.
  2. remove power from the computer by disconnecting the power cord from the computer.
  3. disconnect all external devices from the computer.
  4. remove the battery (see battery on page 27).
  5. remove the optical drive (see optical drive on page 28).
  6. remove the bottom cover (see low cover on page 31).

  as mentioned on page #38 of the following record:

  http://h10032.www1.HP.com/CTG/manual/c04696907.PDF

  DIY will void the warranty.

  Good luck.

• How to open the bottom cover of Ideapad 310 - 14ISK

  Please help me how to open the lower cover, I can't find all the documents that can guide me to do.

  Feel a little frustrated because I have to open the entire background cover just to replace the HARD drive, bad and stupid design imho.

  There is some information about the - 14ISK, but not much

  Drawing, it looks like the HARD drive is accessible from above after removal of the keyboard frame.

  Z.

• ThinkPad Yoga 14 - cannot unscrew the back cover

  I just bought a Yoga 14 TP. I'm looking to replace the hard drive with an SSD. A video on youtube, I checked and I just need to remove the screws from 8-10 on the rear cover and then pull it out completely round hinge. But for some reason, I can't unscrew the tiny screws and proceed to their removal. I use a screwdriver 00 but I tried others. It seems that the screws are unscrewed, but they don't pop, even if I hit the back of the case with my hand. I tried using tongs to hit against the screwdriver stall the in and rotate using the clamp as I've seen in some videos, but it doesn't seem to help. Is there an automatic screwdriver and the size I would be using or else I can buy (amazon, home depot), let me know. Thank you

  Thank you

  I found the answer on another Board

  Here's the captive screws. They are not designed to remove completely and are usually attached to the backplate

  I can always remove the backplate when they unscrewed to halfway

• Remove the back cover of my Y710

  Hi all

  I tried to remove the back cover of my Y710 by unscrewing all the screws that are visible, but the lid in the form of S always seems to be screwed. Just use a little more force, or there at - it a secret to this?

  Just for the record, I am trying to replace the HARD drive.

  I thank in advance

  Steve.

  Success!

  The HARD drive is under the Panel S shaped. To remove the Panel S shaped first remove the screws of 7 or 8. Then, start to lift the Panel upwards from the back (ie the closest edge of the hinge). The front edge of the Panel must be slid and can be popped up, as can the other edges.

  Thanks for your help,

  Steve

• service on the laptop cover

  I read the service manual for my HP Pavilion laptop dv4 and seen the video to remove the service cover. However, the underside of my laptop does not resemble these pictures and diagrams. The instructions tell you to slide the release lever "partially ejected" the coverage of service - but on my laptop, sliding the lever has no effect on anything... except to clear the battery of course.

  I guess my service coverage is the small rectangular panel that covers the optical drive Bay? I don't see any way to remove this piece of plastic.  Am I supposed to completely ignore the maintenance manual and start taking screws twelve?

  I'm trying to be gentle to avoid the break anything.

  I managed to go down the plastic ferrules. The trick is to use my nails. Not on this one. My nails are bad. Now, I will proceed to the next step which is almost surely to unscrew a few screws to open the keyboard. But where are the screws? I read all the manuals of Pavilion model. The three screws indicated in the manual dv4 do not exist on this laptop.

  I close this thread because I down plastic tips.

• HP Pavilion 17 j7b57av: need of repair to install the memory and hard drive

  How can I access my memory and hard drive to add memory and upgrade to a larger disk?  I do not see on the bottom cover access ports, which suggests low overall coverage needs to be removed, but there is always something that is in the manual of th, and I can't find a service manual.

  Please click the links provided which might come handy below

  http://h10032.www1.HP.com/CTG/manual/c04402649

  Hope this helps, for other queries in response to the post and feel free to join us again

  * Click on the white button on the right to say thank you Thumbs Up *.

  Make it easier for others to find solutions by checking a response "Accept as Solution" if it solves your problem.

  Thank you

  K N R K

  Although I am an employee of HP, I speak for myself and not for HP

• I went to the suppliers and lost my connection to get my computer also work like a TV.

  I went to the suppliers and lost my connection to get my computer also work like a TV. gives me the error that I have no configured TV tuner card to work with windows media center. He is told to go into the settings of the TV & set up your TV signal, but I don't know where it is. Please help me.

  Hi Lisa,
  Click Start, click Control Panel

  Click the Hardware tab, and then click Device Manager.

  Right click on the device, and then click Properties.

  Click on the driver tab, then click on set to update driver.

  Follow the instructions on the screen to complete the update of the driver.

  b Eddie

• Disk management will not read the 2nd internal hard drive more!

  Hello

  I am a user of windows 7 and later than yesterday (2016_Feb_02) managing disks stopped to read the secondary internal hard drive (it was working perfectly well before). Does CPU, a beep when it is turned on or even rebooted and more when it comes to the windows logo, the PC hangs for a good 15 seconds.

  The hard drive was an external hard drive and I removed the cover must be installed on my PC, but it has worked well for more than 5 months so far.

  I would like to reuse the hard disk without losing any data.

  Information on PC:

  Compaq

  RAM 2 GB

  Purchased in 2009

  Details of the hard drive:

  Seagate

  2 TB

  Please let me know if more information is needed.

  Thank you very much.

  Download SeaTools for DOS, burn the ISO file downloaded to a CD (you can use the free ImgBurn) and boot from this CD.

  http://www.Seagate.com/support/downloads/item/SeaTools-DOS-master/

• I have a problem with the bluetooth on the computer being lost.

  Hello

  In a search of my volume indicator I refresh my settings of the icon as expected my instructions from microsoft.

  But now my bluetooth icon is missing. Pls help for the same thing.

  Mine is series of Acer laptop Aspire E1-531.

  Concerning

  Hi Anugamini,

  1. are you referring to the Bluetooth icon in the taskbar?
  2. you talk about internal control of bluetooth device to the computer or is it a separate bluetooth device you installed on the computer?
  3. will Bluetooth listed in the list of devices in Device Manager?

  4. What were the Microsoft instructions followed by you. Please clarify?

  If you're talking about only the bluetooth on the computer icon:

  1. click on start.

  2. tap bluetooth.
  3. you will get the results for bluetooth.
  4. If you find the bluetooth icon, you lost.
  5. right click and restore returned to the location that you want.

  If bluetooth is completely removed from the computer. Check if the bluetooth function is running in Windows Services:

  1. press Windows key + R both together on the keyboard key.
  2. in the control run, search box type "services.msc" without the quotes and click OK.
  3. Locate the service Bluetooth service is present in services.msc and started.

  Check if the Bluetooth is listed in Device Manager:

  1. press Windows + X key bot together on the keyboard.
  2. click on Device Manager.

  3. check if you see that the Bluetooth device is listed and to update the latest manufacturer's driver.

  To download bluetooth driver:
  Drivers and manuals

  http://us.Acer.com/AC/en/us/content/drivers

  Update the latest version of the driver for the bluetooth on your computer:

  1. press Windows key + X key together on the keyboard.
  2. click on Device Manager.

  3. right-click on the Bluetooth adapter.

  4. update the drivers.

  Now check if the visible bluetooth on your taskbar of the computer.

  Additional reference:

  How to display the Bluetooth icon in the Notification area

  http://Acer--UK.custhelp.com/app/answers/detail/A_ID/5842/~/how-to-display-the-Bluetooth-icon-in-the-notification-area

  Add a Bluetooth device or other wireless or network device: frequently
  frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows7/add-a-Bluetooth-or-other-wireless-or-network-device-frequently-asked-questions

  Hope this helps, please reply with the status of the question to get help on Windows.

• the hypervisor and its drive system

  Dear all,

  I would like to do a virtual server with two small VMs. (in time real, there will be two virtual server with a virtual computer, and the two of them will be the other backup system, so I have to plan for the worst case, when two virtual machines must run on the same hardware). It would be so complicated, because both vm-s are: a sql express 2012 on a win 7 pro Server (or server win 2012 depend on budget) and special software on a windows xp (or Windows 7). Software restaurant now running on a windows xp with dedicated hardware, so I measured a large number of parameters, including the use of the CPU, utilization of the disk, net use. As for the sql express, it will be a whole new thing, so I can't do action, I can only count the requirements of sellers, but I think that his charge will be relatively low (it's a small business restaurant reservation system database). I read a lot of books and articles, how to calculate the virtual processor, Rams, etc., but all these on the high-end systems. Disaster, two virtual machines will run the same machine, but also at the same time. Data grow is insignificant for the two VM. because of the budget we cannot FCoE and ISCSI as a system disk, so I can only use local disks. And this disk system is confused me.

  In my head, it should be like this for the best effective average budget: a raid1 on top of hardware in the server raid card and all the staff installed on this raid1 (the hypervisor itself and two virtual machines). I'm not sure the system and disk partitioning. Can the hypervisor and guests on the same partition (and drive at all)? Or should I make 3 separate for them? I would avoid using more than two disks, a raid1 with two disk might work like a charm.

  Any suggestion is welcome.

  Thank you very much

  CHR

  ESXi automatically partition the drive of installation/volume and create system as well as the partition (data store) VMFS partitions, so it's no problem at all. However, even with a small budget, you must make sure that the RAID controller takes in charge a battery/flash backed write cache option to operate in writeback mode. Without the write cache, RAID controllers will work in writing continuous mode, i.e. in a way slower than the writeback (> 10 x).

  André