External incoming calls problem.

Hello everyone,

One of our voice gateway router has problem in there. It is malfunctioning and cannot receive incoming call. I think that call is hitting our router and our router is down.

It is a BRI ISDN router with 2 Numéris coming. In the Manager of CCM, it is added as an MGCP gateway, but there his own so dial peer configurations. I checked and it does not any config Manager of CCM.

Here is the debug isdn q931 to.

ISDN Q931 BR0/1/1: RX<- setup="" pd="8 " callref="">
Complete package
Carrying capacity I = 0x8090A3
Standard = CCITT
Ability to transfer = speech
Circuit transfer mode
Transfer rate = 64 kbit/s
The channel ID I = 0 x 89
Exclusive, B1
Called number i = 0 x 81, '510859'
Plan: ISDN, Type: unknown
16:51:19: ISDN Q931 BR0/1/1: RX<- setup="" pd="8 " callref="">
Complete package
Carrying capacity I = 0x8090A3
Standard = CCITT
Ability to transfer = speech
Circuit transfer mode
Transfer rate = 64 kbit/s
The channel ID I = 0 x 89
Exclusive, B1
Called number i = 0 x 81, '510859'
Plan: ISDN, Type: unknown
16:51:23: ISDN Q931 BR0/1/1: RX<- disconnect="" pd="8 " callref="">
Because I = 0x82E6 - recovery at the end of the timer
16:51:23: ISDN Q931 BR0/1/1: TX-> the RELEASE_COMP pd = callref 8 = 0 x 81
Because I = 0x80D1 - reference value of appeal not valid

I also receive a warning message on the map of the voice that is

voice-card 0
! Caveat! 1 DSP at location 0 using firmware by default camera flash:
! It is not recommended, the default IOS version is 24.3.0
DSP services dspfarm

Also see the following output to see the dsp voice detailed command

EDSP 0001 01 g729r8 IDLE 50/0/1.1 0.1 p
EDSP 01 0002 g729r8 p 0.1 IDLE 50/0/2.1
EDSP 01 0003 g729r8 p 0.1 IDLE 50/0/3.1
EDSP 0004 01 g729r8 p 0.1 IDLE 50/0/4.1
EDSP 01 0005 g729r8 p 0.1 IDLE 50/0/5.1
EDSP 01 0006 g729r8 p 0.1 IDLE 50/0/6.1
EDSP 0007 01 g729r8 IDLE 50/0/7.1 0.1 p
EDSP 0008 01 g729r8 0.1 IDLE 50/0/8.1 p
EDSP 01 0009 g729r8 p IDLE 50/0/9.1 0.1
EDSP 0010 01 g729r8 p 0.1 INACTIVE 50/0/10.1
EDSP 0011 01 g729r8 p 0.1 INACTIVE 50/0/11.1
EDSP 0012 01 g729r8 p 0.1 INACTIVE 50/0/12.1
EDSP 0013 01 g729r8 p 0.1 INACTIVE 50/0/13.1
EDSP 0014 01 g729r8 p 0.1 INACTIVE 50/0/14.1
EDSP 0015 01 g729r8 p 0.1 INACTIVE 50/0/15.1
EDSP 01 0016 g729r8 p 0.1 INACTIVE 50/0/16.1
EDSP 0017 01 g729r8 p 0.1 INACTIVE 50/0/17.1
EDSP 0018 01 g729r8 p 0.1 INACTIVE 50/0/18.1
EDSP 0019 01 g729r8 p 0.1 INACTIVE 50/0/19.1
EDSP 0020 01 g729r8 p 0.1 INACTIVE 50/0/20.1

Caveat! 1 DSP at location 0 using firmware by default camera flash:
It is not recommended, the default IOS version is 24.3.0

----------------------------FLEX VOICE CARD 0 ------------------------------
* DSP CHANNELS VOICE *.

CURR STATE: inuse (busy) (b-output) busyout (bpend) held in the waiting
LEGEND: (Bad) download (closed) stop (particles) pending

DSP DSP DSPWARE CURR BOOT PAK TX/RX
NUMBER TYPE NUM CH CODEC VERSION STATE RST AI TS ABRT PACK VOICEPORT
===== === == ========= ========== ===== ======= === == ========= == ==== ============
C5510 001 01 no bad 0.0.0 idle 0 0 0 0/0
C5510 001 02 no bad 0.0.0 idle 0 0 0 0/0
C5510 03 001 no bad 0.0.0 idle 0 0 0 0/0
C5510 04 001 no bad 0.0.0 idle 0 0 0 0/0
C5510 001 05 no bad 0.0.0 idle 0 0 0 0/0
C5510 001 06 no bad 0.0.0 idle 0 0 0 0/0
C5510 001 07 no bad 0.0.0 idle 0 0 0 0/0
C5510 08 001 no bad 0.0.0 idle 0 0 0 0/0
C5510 01 005 None 24.3.0 idle idle 0 0 0 0/0
C5510 005 02 None 24.3.0 idle idle 0 0 0 0/0
C5510 03 005 None 24.3.0 idle idle 0 0 0 0/0
C5510 005 04 None 24.3.0 idle idle 0 0 0 0/0
C5510 05 005 None 24.3.0 idle idle 0 0 0 0/0
C5510 06 005 None 24.3.0 idle idle 0 0 0 0/0
C5510 07 005 None 24.3.0 idle idle 0 0 0 0/0
C5510 08 005 None 24.3.0 idle idle 0 0 0 0/0
C5510 09 005 None 24.3.0 idle idle 0 0 0 0/0
C5510 10 005 None 24.3.0 idle idle 0 0 0 0/0
C5510 11 005 None 24.3.0 idle idle 0 0 0 0/0
C5510 12 005 None 24.3.0 idle idle 0 0 0 0/0
C5510 13 005 None 24.3.0 idle idle 0 0 0 0/0
C5510 14 005 None 24.3.0 idle idle 0 0 0 0/0
C5510 15 005 None 24.3.0 idle idle 0 0 0 0/0
C5510 16 005 None 24.3.0 idle idle 0 0 0 0/0
C5510 01 006 None 24.3.0 idle idle 0 0 0 0/0
C5510 02 006 None 24.3.0 idle idle 0 0 0 0/0
C5510 03 006 None 24.3.0 idle idle 0 0 0 0/0
C5510 006 04 None 24.3.0 idle idle 0 0 0 0/0
C5510 006 05 None 24.3.0 idle idle 0 0 0 0/0
C5510 006 06 None 24.3.0 idle idle 0 0 0 0/0
C5510 07 006 None 24.3.0 idle idle 0 0 0 0/0
C5510 08 006 None 24.3.0 idle idle 0 0 0 0/0
C5510 09 006 None 24.3.0 idle idle 0 0 0 0/0
C5510 10 006 None 24.3.0 idle idle 0 0 0 0/0
C5510 006 11 None 24.3.0 idle idle 0 0 0 0/0
C5510 12 006 None 24.3.0 idle idle 0 0 0 0/0
C5510 13 006 None 24.3.0 idle idle 0 0 0 0/0
C5510 14 006 None 24.3.0 idle idle 0 0 0 0/0
C5510 15 006 None 24.3.0 idle idle 0 0 0 0/0
C5510 16 006 None 24.3.0 idle idle 0 0 0 0/0
* DSP SIGNALLING CHANNELS *.
DSP DSP DSPWARE CURR BOOT PAK TX/RX
NUMBER TYPE NUM CH CODEC VERSION STATE RST AI TS ABRT PACK VOICEPORT
===== === == ========= ========== ===== ======= === == ========= == ==== ============
-END OF THE MAP OF FLEX - 0 VOTES

I hope to receive positive feedback from your people. I checked some documents and they said the default dspware to 12.24 t IOS is 24.3.0 which is displayed in the output with other DSP except dsp 1 and if I'm not wrong, it is integrated in the IOS rather then independent because I can't see any file in flash that could be DSPware. Any help will be much appreciated.

Hello

You get the dsp error message is because your DSP 1 at location 0 is bad and must be replaced.

C5510 001 01 no bad 0.0.0 idle 0 0 0 0/0
C5510 001 02 no bad 0.0.0 idle 0 0 0 0/0
C5510 03 001 no bad 0.0.0 idle 0 0 0 0/0
C5510 04 001 no bad 0.0.0 idle 0 0 0 0/0
C5510 001 05 no bad 0.0.0 idle 0 0 0 0/0
C5510 001 06 no bad 0.0.0 idle 0 0 0 0/0
C5510 001 07 no bad 0.0.0 idle 0 0 0 0/0
C5510 08 001 no bad 0.0.0 idle 0 0 0 0/0

Tags: Cisco Support

Similar Questions

  • Incoming calls problem

    My Xperia M4 double ring does not ring for incoming calls. Speaker works great when I listen to music. And sim 1 guard rejecting calls.
    If there is anything that Sony can do, please fix.

    I am pleased to learn that XperiaM4! Yes, you are only able to choose a ringtone to use for both Sims on the phone, however, you may be able to download a third party application from the game store that allows sim cards to have different one from the other ringtones. May enter "dual sim ringtone" or similar keywords in play store and take a look at the options.

  • SPA 122 and NEC pbx: incoming call problem

    Hello
    I signed a SPA122 on a NEC SV8100 pbx; the device is correctly recorded and can make outgoing calls, but it cannot receive calls...
    The appellant receives a busy tone when SPA phone number calls.
    If I register a CISCO IP Phone 303 the same pbx and using the same SIP account, the phone receives calls correctly, so I guess it's a SPA122 problem and is not a problem of pbx...
    Attached a trace of Wireshark and the SPA122 configuration file.
    Can someone help me please?
    Kind regards
    GIanni

    I connect non sono di lettura delivery easy. Vedo UN

    SP_GET_CALLING_PARTY_NUMBER:FAULT

    My it could avere un meaning che non me lo spiego.

    Ho riconfrontato I messaggi di uno SPA303 con lo SPA122:

    SPA303_OK

    Status line: SIP/2.0 180 ringing

    Message header

    To: 93 >. tag =d1be0d61d79b398bi0

    From: "GIANNI" tag =40503246313536410000533 B

    Call ID: 020289DCC781400000000004@192.168.177.160

    CSeq: 1 INVITE

    Via: SIP/2.0/UDP 192.168.177.160:5070; branch =z9hG4bK8865B851F1A24846

    Contact: "226" 93:5060 >

    Server: Cisco /SPA303 - 7.4.9c

    Content-Length: 0

    SPA122_KO

    Status line: SIP/2.0 180 ringing

    Message header

    To: 187 >. tag =e2fa676e9ab1a8efi0

    From: "GIANNI" tag =D94932463135364100027C20

    Call ID: 02028A28628140000000000C@192.168.177.160

    CSeq: 1 INVITE

    Via: SIP/2.0/UDP 192.168.177.160:5070; branch =z9hG4bK9F3760FE2A28B38B

    Contact: "226" 187:5060 >

    Server: Cisco /SPA122 - 1.0.2 (006)

    Content-Length: 0

    Oltre ad some differenze ovvie come gli indirizzi IP, it call-id, I tag ed branch he, cambia chiaramente lo agent user name o server name.

    No mi che aspect the causa del problema sia questo my tentiamo header. ForSE ha una notazione che non piace al PBX NEC Reed's is ignorarlo.

    Try a nulla would not far away:

    Nella sezione SIP-> settings SIP cancelliamo i campi SIP User Agent name e name of the SIP server.

    Let me know. Grazie.

  • Connect Skype and incoming calls to the PBX - account problem

    Hello

    I have Skype Connect enabled and linked to my PBX with a SIP profile.

    Now, I need activate incoming calls from Skype to my PBX.

    Therefore, I need to link a Skype business profile account, but he refuses because the account I want to connect is a 'personal account '.

    -Can I convert this account to business account?

    - Or maybe I can delete this account and reuse the same Skype name?

    Currently, I have 2 accounts (the admin Manager, "msfsupply" and a different account 'msf.supply').

    I can't activate one of them for incoming calls.

    I would like to be able to use one of these Skype names for incoming calls from my Skype Connect.

    Please tell us what is the best thing to do.

    Thank you

    Renaud

    Haha...

    I started first with the help of Skype.

    They told me to contact microsoft, because it is a business problem.

    I called Microsoft

    They told me that it was not for them either and I should post a question here on answers.microsoft.com to get a technician on that.

    Skype sale:

    https://www.Skype.com/en/business/

    We do not work for Microsoft.

    We are mainly volunteers here, just like you, computer users who give free advice from other users in our own spare time.

    So, all I can suggest is TechNet, if Skype and Microsoft won't help you:

    https://social.technet.Microsoft.com/forums/Lync/en-us/home?Forum=sfbfr

    Kind regards.

  • Problems with incoming calls not being recognized

    I have a motorazr2 V9m.

    Can I use any phone and call my motorazr2 V9m.

    The call will not be displayed on my motorazr2 V9m.

    On the phone, I'm calling from the call will ring until voice mail rises.

    A voice message on the motorazr2 V9m notification will pop up sometimes immediately or later.

    The voicemail notification pop up of time varies. Sometimes it will not show up until you try to make an outgoing call.

    I can call the other phone several times and the motorazr2 V9m will not display a call.

    I'll try 5 or 6 times before the motorazr2 V9m will show and ringing an incoming call.

    I tried this in many places with the same result.

    Any suggestions?

    Thank you

    Looks like a reset did the trick.

  • Problem with incoming calls!

    Can anyone help?
    When my phone rings with an incoming call, my screen remains white. I do not see who is calling you, nor I can answer the call!

    I've restored my phone to factory settings. I followed the process of repair with PC Companion & still does not work!

    Help, please!

    Hi, go to settings - Apps & forehand, then scroll down to IncallUI & select...

  • Transformation of the party calls for different incoming calls whose previous number value (0)

    Community salvation.

    If you see my other discussions created the last days, I managed to configure some functions on our 6.2.1 CallManager. that we really needed.

    But there is a problem and I would like to ask you once again.

    Our internal Cisco phones have 3-digit extensions, from 100 to 999. We had the problem one 0 prerequisite not indicated for missed calls, which I fixed in a translation model that adds two '00' to any incoming call. For outgoing calls, one is removed by the CallManager (PreDot), so called work very well.

    BUT: the translation model that adds the two 00 only works 100% with 10 digits of the external numbers. For example: If a mobile with 0170555yyyy calls an internal number, it is translated to 00170555yyyyy (without translation, it is only 170555yyyyy) and recall works very well. If instead a mobile with 0170555yyyyyzz calls an internal number, it is translated to 00555yyyyyzz. The reason that seems logical: the translation has the value "00xxxxxxxxxx". So it works only with external 10-digit numbers.

    What should I do to make it work with ANY external number? So who calls internal phone - gets two leading '0' being the tracking number by the rest of the caller id?

    Can be simple - but I do not see the answer. :-(

    Thank you. Kind regards.

    Oh, I see what's wrong. You don't need any call mask part xform. Leave the field blank and just add the prefix...

    Please note all useful posts

    "opportunity is a haughty goddess who don't waste no time with those who are not prepared."

  • 7 Windows fax and scan-error message "incoming call cannot be answered as a fax call.

    I use a U.S. Robotics 56 K Fax Modem model 5686 G v.92 and when a fax is sent it tells me that the call has been answered as a fax call and then during treatment, I get "incoming call cannot be answered as a fax call.  I've been working on this for 3 days now and just can't seem to get this point.  Any suggestions would be greatly appreciated.

    Hey Joe,

    You must ensure that your computer (or your external fax modem) is connected to an analog phone line, and that the phone line has a dial tone so that you can place and receive phone or fax calls.

    Method 1:

    Turn on send and receive options for a modem



    Check the modem settings to see if send and receive options are turned on.

    Turn on send and receive options for a modem

    1. click the Windows Start button, click all programs and then click Windows Fax and Scan.

    2. to use the fax at the bottom of the left pane, click Fax.

    3. click on the Tools menu and then click fax settings. Need administrator permission if you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

    4. click the general tab and then, under device name, make sure that the modem is selected.

    5. under send/receive options, make sure that allow it the device to send faxes check box is selected.

    6 make sure that allow it the device to receive fax calls check box is selected, and then choose how to receive faxes:

    * To answer phone calls as incoming fax calls manually by using Windows Fax and Scan, click on manually answer, and then click OK.

    * To have Windows automatically answer phone calls as incoming fax calls, click on answer automatically after X rings, select the number of rings after which Windows can try to answer phone calls as incoming fax calls, and then click OK.

    If someone else set up the computer to send and receive faxes, you might not have permission to use the built-in or external fax modem.

    Method 2:


    Give all users permission to send and receive faxes

    1. click the Windows Start button, click all programs and then click Windows Fax and Scan.

    2. to use the fax at the bottom of the left pane, click Fax.

    3. click on the Tools menu and then click fax settings. Need administrator permission if you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

    4. click on the Security tab and then, in the names box, any user or group, click everyone.

    5. in the permissions for everyone box, select the check box allow next to permission to Fax and then click OK.

    For more information, access the link below

    The problems of fax (valid also for Windows 7)

    http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-fax-problems#EJBAC

    Additional information:

    Configure your computer to send and receive faxes

    http://Windows.Microsoft.com/en-us/Windows7/set-up-your-computer-to-send-and-receive-faxes

    Fax and scan Windows

    http://Windows.Microsoft.com/en-us/Windows7/products/features/Windows-fax-and-scan

    Fax: Frequently asked questions

    http://Windows.Microsoft.com/en-us/Windows7/faxing-frequently-asked-questions

    Please post back with the State of the question and we will be happy to help you.

  • BlackBerry Smartphones BB Flip external screen calling issue Notification

    Hello-

    I've owned this phone for two weeks; and until today it worked perfectly. As of today, the external screen is no longer working for "caller ID" or incoming call notification. The temporary fix was to disable the function "automatic answer" for convenience, even if it does not really solve the problem.

    The question is how to restore the external display as it was working before now with the display of call notification incoming 'caller ID '? Incoming emails, SMS previews; continue to work properly on the external monitor, and the question seems to be isolated to the incoming call notification.

    Is this a bug with the device, or is their a fix to this problem?

    Any help or advice greatly appreciated.

    Hi and welcome to the forums!

    Have you tried the battery pull, we've talked about?

    Thank you

  • Incoming calls mute after updating iOS 10.0.0.2 iPhone SE

    Hello

    After the update of 10.0.0.2, I saw a strange problem on my iPhone SE:

    • Incoming calls appear to be muted 2 ways (the two of us don't hear)
    • The speaker and mute icons on the screen looks normal (non-active)
    • When pressing the speaker icon 2 times (the first time it activates the "speaker" icon, but not the President himself, the second time, it disables the icon) all works fine again.

    It's the same when you use the standard helmet.

    A reboot seems to fix my problem for 1 time. But after that, the problem returns.

    I could not find any related problem, so maybe I'm missing some (new) settings?

    Any help is greatly appreciated!

    Peter

    Hi Montfrooij,

    Thank you for using communities of Apple Support. From what you have said, it seems that you are not able to hear a person during a call on the iPhone. Looks like you already have a troubleshooting.  I recommend you to read this article, it may be able to help solve the problem. You can also check that the iPhone is not connected to a headset Bluetooth, the sound of routing to that rather than the receiver.

    If you do not hear a person on an appeal or a voice message or if the sound is not clear on your iPhone - Apple Support

    See you soon.

  • No sound on the hands-free car on incoming calls after upgrade iOS 10

    I recently updated my iPhone to iOS 10 6s. With one of the versions iOS 9 it makes my hands-free connection in my Toyota 'agitated', but this time I could call people without problem, so I thought everything was ok. That was, until I got a call and didn't hear a thing after accepting it.

    Seems iOS 10 has broken my audio on incoming calls. I can't hear the caller, and the caller does not hear me. I tried to reset network and matching settings once again, but unfortunately which didn't help either (this resolved the problem of stuttering last time).

    Anyone got tips on how to solve this problem?

    DelGurth salvation!

    I see that your car radio on your iPhone Bluetooth connection no longer works correctly.  I know it's important to have this job just so I'm happy to offer assistance.  Please follow the instructions in this article, and it may be necessary to contact Toyota to see if there is an update of the firmware available for your car stereo.

    Help to connect your iPhone, iPad or iPod touch with your car radio

    Thank you for using communities of Apple Support.

    See you soon!

  • Cannot receive incoming calls

    Sometimes. All of a sudden. My phone is in my pocket and someone calls me. I see the cursor that is used to receive incoming calls. But when I slide, nothing happens. Seems that the screen was hung. I remember one day I've relied on the home button and then I could use the cursor and receive the call, but it worked for once. It's boring. I use 6s, latest iOS. Any solution please?

    Hey CoolBrain,

    I see that the phone app seems to be freezing when you attempt to drag in order to answer a call. Certainly, this is not an ideal situation, and I am happy to help you get on the path to solving this problem.

    Before you start, I would recommend that you back up your device either using iCloud or iTunes using the steps here:

    The backup of your iPhone, iPad and iPod touch - Apple Support

    After you back up your device, try to restart it at first to see if the problem persists when you receive a call. If the problem persists, try the steps here to force quit the application and try again:

    Force an application to close on your iPhone, iPad or iPod touch - Apple Support

    If the problem persists after trying the above steps, you will need to reinstall the application phone by restoring your iOS software in iTunes. Take a look at the following resources for more information on this process:

    Use iTunes on your Mac or PC to restore your iPhone, iPad or iPod settings - Apple Support

    Once the restore is complete, try to test "set up in the new" to ensure that the problem does not persist. Once you have finished stable, you can follow the steps here to restore from your backup iOS:

    Restore your iPhone, iPad or iPod touch from a backup - Apple Support

    Take care.

  • How can I convert an incoming call read only an attachment so I can change it?

    How can I convert an incoming call reads only attachment so that I can change it? Save in Word does not it, and find research peut t.

    So, the problem seems to be that attachments are stored as files read-only by Thunderbird and an application it can open without editing privileges, so you cannot change the. Read-only mode was chosen because these files are kept in a temporary location. For example, if you modify and save the back, they are deleted when Thunderbird is closed, so losing your changes. The idea is to force to save you to a different location. You should be able to do it, then open it from that location with full editing capabilities.

    For a permanent change in this behavior, go in the [tools >] Options > advanced > general tab and click on Config Editor there. After you confirm the warning, copy - paste browser.helperApps.deleteTempFileOnExit into the search bar and switch false to true by double clicking on it. Now, saved attachments are created with read/write permissions, but is more removed when Thunderbird is closed (i.e., stored in % AppData%\Local\Temp).

  • No ring on incoming calls

    I have iPhone 6 Plus with ios 9.3.1.  There is no sound ringtone on incoming calls. I turned off vibrate to see if that was the cause, but he has yet to solve the problem. One thing I noticed that if I plug the headset to iPhone, I could hear the ringing sound in the headset. How can I solve this problem?

    Thank you.

    This can help resolve sounds on incoming calls:

    If you hear no sound or distorted sound from your iPhone, iPad or iPod touch speaker - Apple Support

  • New update of Skype - no incoming calls more - Version 4.10.0.332 (4.10.332)

    Hello, SKYPE,.

    Since you provided the new version of Skype for IOS, incoming calls stopped working. I've tried everything. I talked to two of my friends and they know exactly the same problem. I also talked to an agent of very naughty Skype chatting. This is the culmination of the measures already taken:

    1 Delete SKYPE and reinstalled

    2. check that we have the latest version of IOS and SKYPE

    3. under Notifications, made sure everything is turned on

    4. under settings, then on SKYPE, made sure sign is automatically turned on and switch to offline mode is set to 'NEVER '.

    5. also ensured that a device is connected with AN account

    6. it doesn't matter if you call the SKYPE NUMBER or SKYPE to SKYPE, the call does not work

    7 missed calls / messages appears later in SKYPE when you open the SKYPE application

    8. complete reset of the network settings Device IOS

    9. on my iPad, I actually completely deleted and reset the whole device to the factory settings and deleted everything out of it. Reinstalled only SKYPE, but the same behavior. Does not work.

    Incoming calls work on my Mac Book and my PC.

    Also, if you keep the 'in focus' app on your device IOS, which means that you make sure that your screen is not locked or you do not use e-mail, etc., then the incoming calls will work on SKYPE.

    SKYPE: You need to fix this ASAP. It is terrible user experience. I have a real number of SKYPE that I use regularly. My whole family uses SKYPE with each person having their own SKYPE number. Now, we can no longer talk to each other.

    By the way I know that you're going to ask the question, so here's my version of IOS: 6.1.3

    SKYPE: PLEASE CORRECT THIS IMMEDIATELY, OR BE A WAY FOR THE ENTIRE UNITED STATES, BACK TO THE OLD VERSION OF SKYPE.

    See you soon

    All discussions on this topic moved here:

    http://community.Skype.com/T5/IOS-iPhone-and-iPad/no-incoming-calls-since-August-update-4-10-v-when-...

    Go to this link and start reading the page 7 from...

    We can close this thread

    See you soon,.
    Farms

Maybe you are looking for