Extract single channel DAQmx task

Hello

I created a task DAQmx output, which contains two channels.  Is it possible to extract the individual virtual channels of the task to be dealt with by two parallel processes?  I tried to bring out the ownership of channels using a task property node, but then I get the error that the channel is not part of an active task (see excerpt)

Could someone advise on a better approach, or how to obtain this feature - if that's possible?

Concerning

Dave

Sorry, that VI does not have much sense. You must use a unique DAQmx writing for both channels and 1 sample mode, simply build an array of signals as shown below.

Tags: NI Software

Similar Questions

  • Programmatically, create a multi-channel DaqMX task

    Is there a way to create a task of multichannel DaqMX programmatically, without having a task to copy?

    Yes and it is an easy way to find a way to do it.

    Start by creating a task in MAX (Ben, but I want to avod MAX!) Don't be afraid that it's just a one time event that will allow us to know what are the steps)

    Go to a block diagram and steady decline DAQmx task on the diagram and choose the task you created in MAX.

    Right click and select 'create configuration and example '. LV will create the code that goes with the taks.

    Study the config VI that was created. It will show you what it takes to create a task without MAX.

    I hope that helps!

    Ben

  • How to copy DAQmx task without the help of MAX?

    Howdy-

    I hit a bit of trouble here I think points to a fundamental misunderstanding I can have on DAQmx channels and tasks.  I can hack together a workaround, but I would like to know how to do these things, common sense.

    In a Word, I prefer to do everything in the code and not use MAX.  For my application, I would like to create a single channel/task initialized with all the scaling, the physical channel parameters and units (it is what is, in my case, a 'channel').  I would then like to create copies of this channel/task and configure each with parameters of specific task of sampling... corresponding to what I would call the "tasks" to use "Channel".

    I'll have no chance, so of course, I do not understand what I do.  Any reading/posts I've met use MAX.  Here's what I've tried so far:

    Even when you try to use MAX, I am the breath.  Any help straightening on my confusion here is very appreciated.

    Thanks in advance and have a nice day.

    -Brad

    In fact, you're not confused.  In this instance of National Instruments is perhaps...

    See the links ofthese ideas in the link.

    But a 'task' is really just a section in an XML file.  If this file is named *.lvproj the project has access to tasks.  If this file is *.nce any labview application has access to tasks.  If this file is created by the RTE that vi has access to the task.  In short, the "tasks" are never really defined by 'Code' but by the XML code to the file than declairs them and teir properties.  Tasks need to be defined a time-preference during design - project

    Yes, it's a bit simplistic but a good analogy!

    Go ahead and kiss MAX to set your tasks... use DAQmx property nodes if you need to programmatically determine a task property.   "do everything in code" as you say is just not really the way it is... the way I think you hear it...  'S really not 'made it in the code"but rather how LabVIEW is inherintly multithreaded.  The IDE just handles it for you "So easy that could encode a cave man!  Relax and let it work the way it does work for you.

  • Now not DAQmx task correctly

    Hello

    I created a state machine structure that is designed to set up a number of different channels DAQmx data acquisition (the code with indication of analysis section is attached).

    The first time I run this vi, I get a table containing the names of specified job in (with a first line empty), but subsequent executions raise an error that the name of the task is already specified, leading me to believe that the tasks are not properly shut down, but I don't know how to set up the fence vi the task in this case.

    Also, in the State of the initialization, I placed an empty array that obviously gives me my first empty line, but if I withdraw this, he breaks the vi as one of the terminals of the enclosure is then unwired.

    Anyone would be able to guide me to a more correct solution, please?

    -dave

    Purely given this example, here are a few things I would change:

    Use a loop FOR instead of a while loop.  No point in the case of Initialize.  You want to use a shift register to add channels to your task.  It takes only a single task for thermocouples, a task for lubricating oil, etc.  See attachment for a quick example.

    In this example, I think that your error comes from the fact that you create a 2D tasks table.  Each line must have the same number of items, and you get a bunch of NULL tasks.

  • DAQmx task Read DAQmx with sampling frequency of 10 Hz produced much too much data

    I have a simple configuration with a strain of channel 4 OR-9237 amp holds a carrier of series C of WLS - 9163 (wired ethernet mode) - Details probably does not matter.

    I used MAX to create a DAQmx task associated with which all four gauges samples.  The calendar setting is "Scan Loads" is continuous sampling, 2 k buffer (read samples) and 10 Hz rate.  I guess that this task would generate 40 data values per second - 10 for each channel.

    I have a simple loop of reading using DAQmx Read.vi that works always (without any stimulation time).  Playback is set to read all available data and then pump it into a table.
    In the attached example, I also added a few words of debugging to stop the loop after N iterations.

    As the loop is programmed with a 0.2 second period, I expect each pass of the loop to read about 8 samples or 2 samples per sensor.  Instead, I get hundreds each passage.  It's like reading has substituted the sampling frequency specified in the task of the unit.  I absolutely need data to be material to the rhythm.

    Where have I lost?

    Thanks Adnan,

    I changed your example I selected 'Strain gage' entry analog and then lowered the minimum and maximum thresholds to +-1-2.  What happens is that each other in the loop, I 2048 samples or zero samples.  The display flashes a whole line and then it clears any other past.

    In response to your second post, I understand that the loop cannot run quite right that I select.  I think that, but at a sampling frequency of 10 Hz, I have to sleep on the software side for nearly a minute before I built 2 K samples.

    I played with the frequency of sampling, assigning to various values from 0.1 to 10000Hz.  The behavior is the same until I approach the high rates where available samples remains to 2048-4096 sometimes, the display becomes continuous.

    Ahhh, Darn.  Yet another search was this link that points to the root of my confusion.  The 9237 can taste arbitrary rates using its internal clock.  Duoh!  I wish that the pilots are smart enough to warn you if there is a discrepancy between the selected sampling rate and capabilities of the device

  • How to set up wizard DAQ or DAQmx tasks using an external text such as a CSV file?

    I work in an environment were we have a lot of users VI. I develop the VI and technical personnel using the GUI (cover Page) to collect the data. In order to control the input parameters used on multiple hardware platforms, I'd like to develop a generic VI which will import or read a text file I created, and configures the DAQmx tasks to perform data acquisition. In fact, I have the generic VI full and need to understand how to make configurations DAQmx more transparent for the end user as long as the end user has the text file to import. For example, to generate the wizard DAQ DAQmx tasks based on information from text file?

    I don't have time to do more than just a small example. The VI below contains a table with table fixed index functions. This would have changed to get automatically the correct rows and columns, but I hope that you have an idea. I does not have any code to define the type of temperature measurement or to set the correct configuration of Terminal. All of this plus all other possible options will be treated similarly to the definition of the type of channel and min/max which is located in the example.

    Edit-attach VI

  • SE AcceesViolationException NationalInstruments.DAQmx.Task.UnregisterAsyncWaitHandle

    Hello

    I use my own .net application which communicates with NationalInstruments.DaqMx.dll (version 9.7) in order to activate NiDaq in the following configuration:

    Chassis PXI-1033 at two locations PXI-6284, measure differential voltage. This app worked already for a few months and has been tested under high performance - high sampling rate and long hours, without no problems so far. Recently, we tried a new use case - short sessions (60 min) measures running in sample rate = 100 and samples per channel = 100 after a few iterations, we continue to get access violation exception:

    Exception info: System.AccessViolationException

    Battery:

    to NationalInstruments.DAQmx.Task.UnregisterAsyncWaitHandle (System.Threading.WaitHandle)

    at NationalInstruments.DAQmx.Internal.DaqAsyncResult.AsyncOpDone)

    at NationalInstruments.DAQmx.Internal.AnalogMultiChannelMemoryOptimizedMultiSampleReadAsyncResult.WorkItem (System.Object)

    at System.Threading.QueueUserWorkItemCallback.WaitCallback_Context (System.Object)

    at System.Threading.ExecutionContext.RunInternal (System.Threading.ExecutionContext, System.Threading.ContextCallback, System.Object, Boolean)

    at System.Threading.ExecutionContext.Run (System.Threading.ExecutionContext, System.Threading.ContextCallback, System.Object, Boolean)

    at System.Threading.QueueUserWorkItemCallback.System.Threading.IThreadPoolWorkItem.ExecuteWorkItem)

    at System.Threading.ThreadPoolWorkQueue.Dispatch)

    at System.Threading._ThreadPoolWaitCallback.PerformWaitCallback)

    Keeping the sampling rate 100, but his definition of samples per channel at 1000 seems to solve this problem.

    Can someone explain to me what is the cause of this exception?

    Thank you

    Hadas


  • How to store a DAQmx task properties effectively?

    Hello everyone and happy new year!

    I would like to be able to keep track of all the DAQmx task settings (and canals) in a file, regardless of the content of the DAQmx task / channel is. So far, the only way I've found is to use a task DAQmx / channel property nodes and treat every property possible. However, since they are so many properties, each being is not valid for any material or task / channel type, it's a really big job and I'm rather lazy

    So I ask here if someone has already dealt with THIS or have any idea?

    Hi Hillman,

    Thank you very much for the link. Related documents Silly me had neglected tdm... Your link is indeed very useful, as I do right now exactly the same way it's done the:

    • DAQmxTaskInfoQuery.vi
    • General info.VI DAQmx TEDS

    As part of the download in the link you gave.

    Exepted this code is much more readable than mine, so I guess I don't need to view my ugly code incomplete. Many things interresting, thank you very much. I'll be back if I have something better to give as a reference.

  • HP Pavilion Slimline S5 - 1050d: Upgrade of RAM - single channel memory


    Hey, I want to just update. I installed another 4 GB of RAM with the same features (I decided to buy online).

    It works and BIOS shows two-channel after 2 slots taken.

    So, I guess he showed single channel because only simple slot taken.

  • Get the Max values and average of the different cycles in the single channel

    Hello

    I'm trying to get the Max values and average of the single channel that has different cycles it contains. I tried to use commands such as Chnclasspeak3 and chnpeakfind, but they were not useful for me. What I need is the Max values and average of the different cycles numbers saved in the data channel.

    Exampld if the string contains 5 numbers of repetitive cycles, then we must find the maximum values and the average of these 5 cycles in the single channel. Attached reference data. This is the .raw file and I have the plugin for it to use in diadem 11.1.

    Kind regards

    X. Ignatius

    Hello, Ignatius,.

    Sorry, it took some time to provide a replacement based on the script for the function. Please take a look at the attached script. I changed the script to use my function if the tiara-version is less than 12. My script function is not as fast and more stable than the implementation of tiara, but for now, it does the job

    Andreas

  • How to add DaqMX task to an existing project

    I use Measurment Studio 2010 with Visual Basic. I created a NI Daq Windows application with an element of task Daq to analog input.

    Now, I have to add additional DaqMX tasks (tasks in digital and Digital Out) to the existing Visual Basiic project.

    How can I do this?

    Thank you

    Mike

    Hello

    Here is a link that shows how to add a task to a .NET project

    http://digital.NI.com/public.nsf/allkb/290D84D10809D4C086256FF20076F8B8

    Curt

  • Convert DAQmx task IDS in a string

    I'm using LabVIEW to perform a generation analog DAQmx and I call my LabVIEW of CVI code via a dll.  I want to make two separate calls, one to start a task DAQmx and one to stop the task, so I need to either:

    (1) move a task ID DAQmx CVI and then again to LV

    or

    (2) convert a string of the ID for the task, pass it to CVI and then back to LV and then convert back to a task ID in LabVIEW.

    I'm sure that option 2 is the easiest option, but I don't know how to convert back and forth between a string and a task ID DAQmx.  Can anyone help with this?

    Thank you

    Joe

    Nathand is correct, it's pretty easy convert from/to the task DAQMX and String.  The two below

    Hmmmm is note expected or a bug?

    Feedback probably need an expert of DAQmx to answer that - I think it might be related to level DAQmx tasks

  • ini to physical channel DAQMX channel

    I would like to save all my physical channels DAQMX as strings in an ini file.  My program reads information in string and convert to the physical channel DAQMX.  Is a kind ride the only way to convert a string to a type of DAQMX channel?  I wanted to tell all of my information communications in an ini in case something change.  Thank you!

    Not cataloged. You can wire a string directly to the entrance of the channel.

  • DAQmx task: MAX or lvproj?

    Experts,

    What are the benefits to declare tasks DAQmx either in the lvproj or Max?

    My question because I'm calling a VI of TestStand test, and when the DAQmx task constant is declared in the project (lvproj) which holds the criterion VI, it does not perform properly, saying can't find the reference or something.

    If I change the DAQmx task to be a global task in MAX everything works as expected.

    What is the best practice to do this kind of things?

    Thank you very much

    LR2

    TestStand does currently not support execution of VIs a project. So unfortunately, we expect the behavior that you see where to call a VI that uses a DAQmx task defined in a project does not work. For now, if you do want to keep your configuration of the task outside the source code and you want to use these task for TestStand, you must store the Max.

    We are looking for by adding support for the performance of screw a project in a future version of TestStand.

    David Rohacek

    National Instruments

  • HP 21-2024 all-in-one desktop: Single Channel Architecture

    Just bought an all in one PC for my family and it comes standard with 4 GB of RAM running Windows 8.1.  I would like to upgrade the RAM, 16 GB of RAM to help with the slow performance that we see.  The documentation says that the motherboard has a single channel architecture.  I can't find any ddr3 memory that are not dual channel kits.  Can I put into sticks dual channel and everything still work?

    Thanks in advance for your help.

    Hello

    See the bottom of specifications of memory for your PC.  HP has the DIMMs of memory you need.  The memory will run in single channel mode verses the typical dual channel, but unless you have some intensive memory access applications I doubt you will see much of a disorder of the performance.

Maybe you are looking for

  • How to add the Firefox search bar

    I would like to add the search bar Firefox 35.0.1 for me to change search engines. How can I do this? Thank you

  • iPad pro 9.7 inches

    Can someone give me the dimensions of the cover silicone for iPad pro 9.7 inches; for example, how to bulk it adds to the iPad? Seems silly, I know.  just trying to determine if my pro will still be compatible with a keyboard that I have if I use thi

  • "Could not connect to the server Game Center"

    OK, so here's the deal: Im trying to connect to Game Center on my old phone to synchronize the progress of game. When I try to log in, it tells me that it could not connect to the server. I tried just about everything I could find on the Internet wit

  • program Rbase 32 bit on 64 bit, Win 7?

    How can I run program Rbase 32 bit on 64 bit, Win 7?

  • Why blackBerry Smartphones is not anyone I know, know my phone; 9790 bold?

    When I got my new 9790 Blackberry "BOLD" just the other week, I was very happy to show. Except anyone I said had never heard of this model and thought that maybe it's too new? Even now, I tried to get help on this site, it is required for the model o