F3507g cannot reconnect

Similar Questions

• Cannot reconnect the external hard drive

  Cannot reconnect the external hard drive after moving the computer. I have a WD external hard drive and after moving computer cant use. It is used to mount drive f and now in the g drive. He keeps asking me to format the disk before it can be used, but cannot do so. I am desperate to back up my files but can; "t.Any help would be much appreciated

  Hello meatindustries,

  What operating system do we use?

  The answer to this question, we can pursue various troubleshooting methods.

  There are many third-party data recovery utilities available for free online.  You can search for these using your favorite search engine to find one that you like.

  Let us know the operating system you are using and we can go forward from there.

  Best regards

  Matthew_Ha

• Want 7640: HP Envy 7640 dropped off the grid and cannot reconnect

  Envy 7640 dropped off the grid and cannot reconnect. I followed the instructions on the previous thread without result - restoring network, cycling settings, router, modem, etc... printer indicates "failure" for the "no filtering". All other wireless devices work fine. Please notify

  Please provide the following information if anyone can help including:

  The printer model - done

  Operating system on the computer (including service pack revision) - done

  Detailed - description of problem including all devices network (extensor, switches)

  Connection method - Direct wireless, wireless, wired LAN, USB? -

  Number of brand and model of router and modem? -

  Error messages - on the screen of the printer or computer, no matter what flashing light patterns? -

  Do you think the printer is going to sleep and can't wake up? -

  If wireless, in the event of problem, what is the status of the blue wireless light on the printer, active, disabled or flashing? –

  Power off the printer and the router.  Power on the router and wait 3 minutes, power on the printer.  It connects to the router now?  What is the IP address of printers?

• TOSHIBA f3507g cannot connect to mobile broadband from 3G (error code 0)

  It's really a strange situation. Yesterday I installed the latest 3GRF POWER UTILITY and driver F3507g 3 G then inserted the SIM 3G, my laptop can connect to the internet (HSPA) normally, but today when I download and install the latest software WIRELESS MANAGER in others to check data and texting, but now my laptop cannot connect to the 3 G network but that laptop still the 3 G signal. I also tested for texting on my phone and it works but connect to the 3 G internet is impossible. I tried to uninstall all the drivers of 3G and reinstall it again, but it does not work. When I cheking troubleshooting, he said that "the operation of network connection mobile broadband failed with error 0". I use win7 and download the driver 3G [http://aps2.toshiba-tro.de/wlan/]. Please help me, thank you very much!

  Hello

  What operator and SIM are you using? It works if you connect through the Win7 built-in connection manager? That is to say through her view available networks?

  Since you are able to receive text Messages, you can register properly to the network. This should be a profile/network problem. It works if you create a manual Profile Manager wireless with the correct settings for your carrier?

  It works if you use square DUN? See Howto on http://aps2.toshiba-tro.de/kb0/HTD9802OF0000R01.htm

• Disconnected ESXi host cannot reconnect to VCenter

  ESXi 4.0.0 Releasebuild-261974

  VCenter 4.0.0 build 162856

  VSphere 4.0.0 build 162856

  I have a host on the 16 who became disconnected from VCenter recently. I spent some time online means to join new host in VCenter, but each has failed so far. I'm not avoiding perform a reboot of the host due to production VMS are residing thereon. Also, I can't access the Web page for the host, which works very well for the other guests, we have running: https://

  I am able to ping both the IP address and the name of FQDN of the host successfully.

  I did the following things in the hope of resolving, who all have failed:

  1 restart the Management Agents on ESXi host from the windows of the customization of the system.

  2. test the management successfully and rebooted network management network

  3A tried to reconnect to the host via VSphere

  4 registered and the Mode of Support Tech executed the following command: /sbin/services.sh restart when I run this command, I notice that the vmware-aam service does not start.

  Error messages:

  1. (in an attempt restore the link) cannot communicate with the specified host. The host may not be available on the network, may have a network configuration problem, or that the management on this host services may not respond.

  2 (of the newspaper of the Management Agent) panic HttpNfcSvc another process is listning IDE oucederomsurlesecondport 12001; Please ensure that another instantiation of pass run; Cannot initialize the service of httpnfc.

  3. (journal of the VirtualCenter Agent) 0x1499bb90 error 'App' could not discover the ofr is authenticating with host agent version. ; could not resolve version ofr is authenticating with host agent. ; Temporary creation connect spec: localhost:443.

  4. (of the newspaper of the VirtualCenter Agent) 0x1499bb90 error 'App' SSLStreamImp::BIORead (0x2e408bb0) has expired; SSL connection failed with error BIO

  [5 (journal of the VirtualCenter Agent) HttpUtil::ExecuteRequest] error in sending request - SSL Exception: transfer the SSL expired local: 127.0.01:63355 peer: 127.0.0.1:443

  Any suggestions would be greatly appreciated! Let me know if you need to work as well with more information.

  Thank you!

  BOE

  It is an ugly one. At least a restart if not re-install. To minimize downtime, you can close out of virtual machines to the inventory and put them on another host/cluster.

  ___________________

  A +, EASD, MCP, MCSA, MCSE, MCTS, MCITP, MCDBA, NCDA, VCP4

  If you find this or any other answer useful please consider giving points by checking the correct or helpful answer.

• Cannot reconnect 'missing' photos

  After you have imported all my photos of PS Elements 8, taking the default values, I was presented in the grids of the cell library to the icon broken in the corner upper rh. When running "find her lack of Photos", I got a report saying there are a few 13 678 'missing' photos. I then followed the procedure in a help file to locate missing photos, who described their last visit. However, there is no reconnection done once I've completed this process. Then, I went in PS Elements 8 and searched for one of the names of files that went 'missing '. The result showed two different pictures, in two different locations, but with the same. JPG name. I recognized the two photos as being valid, but you're wondering how to proceed with what seems to be a reason why the rating 'missing', I say that the software cannot deal with dupicate names. I certainly did not expect this 'missing' statement, so a lot of images seems there are a lot of recovery to do, perhaps in the area of renaming one of the images duplicated; for example. filename_1.jpg.

  Did you see this problem, and what would you recommend to fix?

  Thank you very much.

  Fred

  Regarding the upgrade a catalog of items to Lightroom, follow these instructions

  http://TV.Adobe.com/watch/going-from-Photoshop-elements-to-Lightroom/importing-an-elements - catalog in lightroom.

  Please note: If you have imported all the pictures, as you say, then this is not the right way to create a Lightroom Catalog from a catalog of items. The correct method is shown in the video.

  Regarding the missing files, I really don't know what caused them, but I'm 100% sure that they were not caused by duplicate files names, that should not be a problem in organizer or Lightroom. When you say "I then followed the procedure in a help file to locate missing photos, who described their last passage", might be more accurate, exactly what is the procedure, what commands and what did the steps you use?

• Printe all-in-one Deskjet 3520: cannot reconnect my printer all-in-one Deskjet 3520 wireless network

  Hello!

  I'm having a problem to reconnect my printer on the wireless network. I unplugged for a few days and now it won't connect to the wireless network. I get the following message on the small screen on the IP of the printer: not connected SSID:N / A. I hope you can help me solve this problem.

  Best regards

  Mina

  Hi @Mina85 and welcome to the Forums of HP!

  I see that you are having connectivity problems.  I would try to help!

  I recommend you to perform a power reset.   Unplug the power cord from the printer and the power outlet, then wait 60 seconds. After 60 seconds, plug back in the printer. Make sure that you connect the printer directly to a wall outlet. Make sure to bypass any surge protector or power bar.

  I also suggest this document on Center of troubleshooting wireless printing.

  Good luck and please let me know the results of your troubleshooting operations. Thanks for posting on the HP Forums!

• Cannot reconnect my Smartphone using Bluetooth

  Hello world

  I have connected my Samsung Galaxy android for my Toshiba Satellite (windows 7) via Bluetooth to receive GPS data to use on my graphics path program.

  Easy to do, BUT if I disconnect the device and then try to connect again, BT Stack will not reconnect. While trying to reconnect, there is no request to for passkey and I guess that's maybe part of the problem.

  I installed the last BT V 8 stack, but this does not resolve the issue. Please help before I go crazy.

  Sincere greetings
  Michael Barrett

  Hello

  Have you tried to use the secret key Fn + F8 to disable and then enable the BT after the smartphone has been disconnected?
  Please check this!

• Aspire one "cannot reconnect network card.

  OK, so I have an Acer Aspire One AOD260 net book I've had for a few years.

  Internet connection no longer works, WiFi is not my thing, so I ran the troubleshooting and it comes up saying there are problems with the network adapter. I get the message "unable to reconnect to the network card.

  I get this message no matter where I am, so I think that the problem is with the Netbook not a router or a Modem.

  MS Windows 7 Home Premium 64-bit
  Intel Atom CPU M550 @ 1.50 GHz 2.0 GB RAM
  Graphics controller Intel GMA 3150

  Device Manager says:
  Atheros AR8152 PCI - E Ethernet controller
  Broadcom 802.11n network adapter
  Microsoft Virtual WiFi Miniport adapt

  Under network connections, it will list 2 with a red X, Broadcom 802.11n does not, but it says unidentified network, no internet connection.

  What did I try?
  I have tried to plug the Ethernet cable from the computer - no change, still get the message of the adapter
  I tried to plug in an adapter N900 Wireless dual band USB - no change
  I disabled the firewall and AV - no change software

  I've uninstalled and reinstalled all the drivers - no change

  Yes my router works on everything except this Acer

  As I said that WiFi is not my thing, so I really need help how to solve this problem. Please Suzie

  Download this 2 packages and install them:

  Atheros LAN driver

  http://global-download.Acer.com/GDFiles/driver/LAN/Lan_Atheros_1.0.0.35_W7x64_A.zip?acerid=634558012...

  Broadcom wireless LAN:

  http://global-download.Acer.com/GDFiles/driver/wireless%20LAN/wireless%20LAN_Broadcom_5.100.249.2_W7...

• Windows XP Home cannot reconnect my player card after each session of re - start, quick to key in the username and password still.

  I recently installed a network storage drive to my network environments with desktop computer running windows 7, windows xp professional and windows xp home.

  Have this problems that even when the drive has been mapped with identification information entered and save selection 'auto re - connect on each session' in windows xp home. Computers running windows xp professional, and windows 7 allows me to create and record identification information that allows the reader to reconnect each time the system starts up, but not on xp family.

  Tried several methods of control over the update of the firmware, upgrade of service pack, part 3 card utilities and windows drive mapping manual, but it does not help.

  Hope someone could give advice what could be done to solve this problem because it seems very likely that it due to windows problems.

  Under user account, manage stored password options, I could create credentials in XP Pro, but not at home.

  Thanks for your reply.

  Correction of syntax: there is an oblique lack between "servername" and "share name".  The slash in front of 'USER' is also the polarity.  It should be rather than the oblique as in:

  NET use Z: \\servername\sharename / USER: username password

  -JW

• Cannot reconnect to the drive mapped with the offline files

  We have Vista Business SP2.  We written that makes some of their files on a network share available offline.  They close their machines and take them away and use not connected to the network and then to arrest them.  Back at his office, startup and reconnecting to the network, their network drives appear offline.  Clicking on returning their online status unless they have offline files, then no amount of clicking, fiddling, disconnection and reconnection, or anything else we might think will persuade the reader to come online.  How force us the computer to notice of the network to share?

  Hello

  Thank you for using the Microsoft Windows Vista Forums.

  I will need some additional information to help you best.

  • The computers are connected to the domain?
  • How many computers are connected to the computer problem?

  In the meantime, try the following steps.

  1. Right click on computer and then click map network drive.
  2. In the folder field, specify the location of the sharing Web.
  3. Click to select the check box to reconnect at logon .
  4. Click Finish.

  Please post back and let us know if it helped to solve your problem.

  Kind regards

  KarthiK TP

• 3055a HP Office Jet: cannot reconnect printer WiFi after change of password and name

  Hello

  Past changed SSID and WiFi.

  I have restored the default settings on printer. No option on the control panel wireless Assistant Configuration.

  On my ipad, I connected to the wifi-HP-setup-3F-etc and loaded in Safari. Typed in 192.168.223.1 and got the HP Desk jet page. Tried to run the Setup Wizard from here but in step 1 wireless, he just said: treatment and is not further?

  Assistance required. This should be an easy task, I feel but been this frustrated for hours now.

  Hi helpanewbie,

  You are welcome! No worries on the issues, it's why I'm here!

  Have you tried rebooting the iPad and Mobile phone? Sometimes, after having reconnected to the network, a reboot is required.

  In addition, this guide, A connected network printer access printing applications, Web Services, or ePrint impossible, could help as well!

  If this, or one of the posts on this thread, helped you to solve the problem, please click on accept as Solution on the message. To show you 'like', or that they are grateful for my post, please click the thumbs upwards below. If there is anything else I can do to help, please don't forget to let me know!

  I hope this will solve your problem!

• P1102w - cannot reconnect to the network

  I can't reconnect my printer laser p1102w to the network, or my system.  When I connect the USB port on my laptop, it attempts to save the connection, but does not a drive letter or anything like that.  I downloaded the latest installer.  When I try to add the printer and set it up for wireless access, nothing happens.  When I try to add and configure to access usb, installation product until he asks for the usb connection, how does not "meet" the printer when I plugged it.  (Yes, I tried several ports)  I tried the 'doctor' and he seems to be satisfied with it as a usb connection.  However, I don't know how to get connected to the net.  Is it possible to do this simply?

  Salvation for the end user.

  I see that you are having a problem with put the printer on the network again.

  I'll be happy to help you.

  I would like to reset the printer first to clear the previous network settings.
  Turn the printer off, press and hold the wireless button and cancel (x button) while turning the printer on and do not release both buttons until the printer stops making the noise.

  Print a configuration report and check the SSID address and IP are disabled.
  (hold down the x key and when the printer makes a noise to let go of taken)

  After the reset, unplug the router power cable, wait 10 seconds, then reconnect the power cable.

  Wait, it's ready.

  Because the USB connection does not work now, unplug the USB cable.

  Run uninstall from the CD or the program files.

  Here are the steps to run the uninstall of the computer or the CD.

  To uninstall program files:

  Go to start and select a computer.

  Select the C drive.

  Select the program files or program files x 86.

  Open the HP name and printer folder.

  Select uninstall.

  Uninstall from the CD:

  Go to start, computer,

  Make a left click Open in a new window, right click on the printer CD, double click on uninstall.

  Run the Setup again and do not connect the USB cable until you are prompted to configure the wireless again.

  Test the printer.

  I would setup an IP address from the printer so that it does not happen in the future.

  Printer keeps not WiFi. Proceed to Solution 4: assign your printer a static IP address.

  What operating system do you use? How to find the Windows Edition and the Version on your computer.

  Please let me know if you need additional assistance.

  Thanks for posting on the HP Forums.
  Good day.

• OfficeJet J6410: Cannot reconnect to wifi printer

  I changed my wifi router, and since then my printer will not connect to wifi.  I tried to restart the printer and the computer.  I tried turningh on the printer, the wifi button.  When I run the diagnostic check tells me that there is an error.

  So, how to reconnect?

  Replacement/change your wireless router try here.

  http://www.HP.com/global/au/en/wireless/reconfiguring-system-Help3.html

• Cannot reconnect my LUN shared with no format.

  Hi all

  I need your help, because I have a big problem, I expose it to you:

  I have two ESX 3.5U3 and a SAN with 3 Mon.

  Lun0 is the main, it's with all my virtual machines logic unit number this LUN has been shared between ESX 1 and ESX2.

  Today, I stopped in my vm and stop ESX1 and ESX2 guest. When I rebooted, the LUN mapping has been removed.

  On the san, a cautionary note my that the host mapping has been killed.

  I've recreated the mapping on the SAN, rescan on the ESX, ok, they see my LUN0, but when I want to add the existing LUN, my ESX want the format of the logical unit number.

  How to add the LUN0 without format the LUNs, or a solution to extract my vms?

  Thanks a lot for your help

  David

  Extend your LUN?  Did you change the LUN after extension on the LUN?  As long as you don't try to go and change settings on the expanded LUN, your data should be in tact.  However, given that the disc has "changed", it is perceived as a different LUN, allowing adjustment that I spoke with.  Also, you cannot extend a VMFS in the method you tried.  What will happen is that there will be a blank space after the end of your existing VMFS.  The VMFS itself not may be extended, even if the LUN can be extended.

  -KjB

  VMware vExpert