faild - replace hard disk 1 (security id - error code 10008)

When I open up my laptop so they gives error - faild - replace hard disk 1 (security id - error code 10008)

can u tell me what I can do... but my hard drive works fine, but gives this error... you can tell me... .what I can drive u, can replace hard drive or not... and also my laptop warranty is expired... u can tell me one thing when I replace it my hard drive... .then they give me some conssesion or not... .and when my laptop gives error so can u tell me one more thing my hardisk recover or not... Please tell me...

Hello

You can run a test on your hard drive to make sure if its in a State of operation or do not use the link below

http://support.HP.com/us-en/document/c00439024

If the above test fails, you will need to replace the hard drive. You can buy the hard drive by going to the HP service center or any place where you want. To reinstall the operating system, you will need to buy the recovery disk set by calling HP techinical support.

Tags: Notebooks

Similar Questions

  • Pavilion a1230n w XP: Replace hard disk & recovery disks don't work

    Replace hard disk & recovery disks do not work. Create the new partition & Microsft Recovery Console ONLY the options available on the disk recovery TOOLS. Recovery of Microsoft stops at the page "Preparing the system to install Windows XP".  Pressing enter at this stage of the results in "cannot find EULA" message & turns off the computer... already old version of XP (media center) via another set of discs, but want software HP original back!

    If it starts from the cd Recovery Tools but not the recovery DVDs, then you can have a bad set. Of course, it could be laser dvd in your CD/DVD drive too. The dvd function works before reinstallation?

    Don't see them not listed in HP longer, but are available HERE for $27

  • Have installed Photoshop CS4. Replaced the drive hard and now I get error code 150:30. What should I do to get it working again

    Have installed Photoshop CS4. Replaced the drive hard and now I get error code 150:30. What should I do to get it working again

    Migration of CS4 breaks the license. That's what 150:30 means. Assuming you are using a Mac.

    You can use the Terminal method to repair the license... but I stress that carefully read you and understand the instructions here before you run it. beginning

    # 11. https://forums.Adobe.com/thread/1714695

    If this isn't what you want to do, you have to reinstall.

    Gene

  • Security #KB974571 error code 0 x 80070008 cannot install

    I tried to install this over and over again with a bit of luck. All other updates to the low load and install no proublem but it down loads but does not install!

    (#KB974571 security update error code 0 x 80070008)

    Hello

    1. Did you the latest changes on the computer?
    2. You have security software installed on the computer?
    3. You are able to install some other updates on the computer?

    Method 1

    Error 0 x 80070008 means ERROR_NOT_ENOUGH_MEMORY.

    Check and make sure that you have enough free space available on the drive on the computer, I would say that run you disk cleanup and if it helps.

    Description of the tool in Windows XP disk cleanup

    http://support.Microsoft.com/kb/310312

    Method 2

    If fails it above step can refer to the article below and try the steps mentioned, check if it helps.

    You may encounter temporary connection related errors when you use Windows Update or Microsoft Update to install updates

    http://support.Microsoft.com/kb/836941

    Also, try to install the update manually and check if it helps.

    Update security for Windows XP (KB974571)

    http://www.Microsoft.com/download/en/details.aspx?displaylang=en&ID=21486

  • Error on verification of messages against security policy Error code: 3603

    Hello

    We are migrating our WL10.3 WebServices to WL12.1.2 and we have not been able to rely on them as we have done on 10.3. On their WSDL is indicated like this ws security policy:

    < wsp

    ' xmlns:wsp = ' http://schemas.xmlsoap.org/ws/2004/09/policy "

    ' xmlns:sp = ' http://docs.oasis-open.org/WS-SX/WS-SecurityPolicy/200702 ">

    < sp:SymmetricBinding >

    < wsp >

    " < = sp:IncludeToken sp:UsernameToken ' http://docs.oasis-open.org/WS-SX/WS-SecurityPolicy/200702/IncludeToken/AlwaysToRecipient ">

    < wsp >

    < sp:HashPassword / >

    < sp:WssUsernameToken10 / >

    < / wsp >

    < / sp:UsernameToken >

    < / wsp >

    < / sp:SymmetricBinding >

    < sp:SignedSupportingTokens >

    < wsp >

    " < = sp:IncludeToken sp:UsernameToken ' http://docs.oasis-open.org/WS-SX/WS-SecurityPolicy/200702/IncludeToken/AlwaysToRecipient ">

    < wsp >

    < sp:HashPassword / >

    < sp:WssUsernameToken10 / >

    < / wsp >

    < / sp:UsernameToken >

    < / wsp >

    < / sp:SignedSupportingTokens >

    < / wsp >


    When we try to use this webservice of the new WebLogic 12.1.2 domain we receive following SoapFault

    " < = xmlns:wsse env:Fault ' http://docs.oasis-open.org/wss/2004/01/oasis-200401-wss-wssecurity-secext-1.0.xsd ">

    WSSE:InvalidSecurity < faultcode > < / faultcode >

    < faultstring > message error on the check against security policy Error code: 3603 < / faultstring >

    < / env:Fault >

    Can someone help with this problem? We do not know what is missing or if there are additional required configuration or incompatibility.

    For more information, these guidelines was considered:

    Thank you in advance and best regards,

    Ruben

    Finally, I discovered what was going on.

    This error is produced by a NullPointerException on the line of weblogic.wsee.security.wss.plan.SecurityMessageInspector class 535 when you call the getDigestMethod () .getAlgorithm)

    REF = this.svalidator.getReference (st, this.blueprint.getXmlSignatureFactory () .newDigestMethod (signingPolicy.getDigestMethod (.getAlgorithm ()), (DigestMethodParameterSpec) null), new ArrayList(), token.isIncludeInMessage ());

    Which differs from the version 10.3, where a default collection method is provided

    localObject1 = this.svalidator.getReference (localSecurityToken, this.blueprint.getXmlSignatureFactory (.newDigestMethod)("http://www.w3.org/2000/09/xmldsig#sha1", (DigestMethodParameterSpec) null "), new ArrayList(), paramSecurityToken.isIncludeInMessage ());

    Trying to understand the policy of the WS file, I decided that if we use a SignedSupportingTokens must also configure how tokens must be signed, otherwise use the SupportingTokens instead, which is what I did.

    So eventually, if the policy was not set properly, I do not understand why in this new version a NPE is triggered (wrapped in an error code 3603). Maybe it's a bug?

    See you soon,.

    Ruben

  • Error - 10008 # replace hard disk 1

    I'm sure that my hard drive has become bad, other messages that I read.

    I don't have any data out of this device.  In fact, I was about to start deleting old data so I could give this device to a family in need.  Went to start the computer to start this process.  However, when I went to do this, he went to BSOD.  Messed with it a bit, then I got BSOD.  I have fillany calculate to run the test and got the 10008 # replace 1 hard disk error.

    As always, I want to give to this family that laptop, my question is: where I could buy a cheap replacement hard drive.  Is it difficult to do? And I don't think I have a back up / but on the operating system installation disk.  I have to do to get us to open and it would be affordable.

    I'm totally willing to put in the work to get to the top and go, but was woundering if anyone would be willing to give me some instructions on how to do it.

    Thank you 1 million for all advice and assistance.

    Hello

    Regarding the reinstallation of the operating system on the new drive HARD, here are two options.

    1. you can order a set of replacement recovery disks using the link below - it will reinstall the operating system, all the drivers, and almost all of the original software (the exception being often tests of MS Office).  They will also recreate all of the original scores, including the recovery Partition.

    Order HP recovery disks.

    2 another option that you might consider is to create your own Windows 7 installation disc.

    Before you try the following, make sure that you can always read the character product activation key 25 on your label Windows COA (5 blocks of 5 alphanumeric games).

    An example of a COA label can be seen here.

    You can create a Windows 7 installation disc yourself using another PC - just download the Disk Image correct ( this must be the same version that originally came with your laptop - it is listed as Windows 7 Home Premium 64 - bit ) from the link below and use an app like ImgBurn ( Note: you can deselect additional software during installation of ImgBurn offerings) to burn the ISO correctly on a blank DVD - a guide on the use of ImgBurn to write that an ISO on a disc is here.  The source of the Windows Image is Digital River.

    Windows 7 Home Premium 64 bit SP1.

    Use the disk to perform the installation, enter the activation key of Windows on the label of the COA at the request and once the installation is complete, use ' 'phone Method' described in detail in the link below to activate the operating system -this made method supported by Microsoft and is popular with people who want to just have a new installation of Windows 7 without additional software load normally comes with OEM installations.

    http://www.kodyaz.com/articles/how-to-activate-Windows-7-by-phone.aspx

    You may need, additional drivers and software are here.

    Best regards

    DP - K

  • SMART Hard Disk Error - replace hard disk?

    A couple of days, I got an error when I start my computer (HP Pavilion dv6-6071eo), saying "SMART hard disk error" followed by a message telling me that SMART disk check has detected and imminent failure. He told me to my backup files, and then press F2 and do a hard drive test. On the last row, it displays "Hard Disk 1 (301).

    I tried to run the hard drive test, which does not instantly. I also ran the BIOS hard drive test. It meets the short test without problem and then stopped quite some time after the long trial began with the error "Disk Hard 1 full 305. My computer has also been slow over the last week.

    From what I've read so far, it seems that I need to replace my hard drive. Is this correct? If so, it would be a suitable replacement (functional): http://www.dustinhome.se/product/5010151237/western-digital-black-2-5-320gb-7200rpm-sata-300-16mb/#i.... Also, would it not interesting (and possible) upgrade to an SSD for reduction of noise and heat, which is a problem with this laptop (and several other portable simular at HP) compared to other laptops.

    In addition, it might be good to mention that my warranty has expired.

    Have you checked to see if there is a free space left on the hard drive? A complete hard drive will make the system work very slowly and it may also keep the system working properly if it is fairly comprehensive. The fact that you take the short test means that there is nothing major to mechanically wrong with the drive. Just right-click on the icon for the main C:\ drive likely "computer: and select 'Properties'.» If the disc is not actually full, then I suggest to replace. If you can afford a SSD, Yes, there is no doubt that is the way to go. There is nothing wrong on one ssd, other than an occasional fight to install it. I have been using SSD for awhile and I had installation problems we often see reported here, but do not be discouraged, we are here to help.

  • HP dv6500 - replace hard disk?

    I have HP dv6500 for over 2 years now and I am outside the warranty period.

    -VISTA Home basic

    Recently, ny computer started freezing after every 15-20 minutes and it was not usable, I had to reboot always out...

    I ran the BIOS disk HARD diagnose - it says "Replace hard drive".

    I called HP support - but they were not willing to help with hardware issues, without any mandate that costs ~ $ 350 +.

    That's why I thought to replace the HARD drive with a new one.

    Old SATA HDD: WD160GB

    New SATA HARD drive: Seagate 250 GB

    After replacing the HARD drive, I tried to restore the system using original HP recovery disks. It runs through the process of recovery - restart the computer several times - finally throws an error:

    "Unable to start Windows. Recent hardware or software change might be the cause. »

    "file:/Windows/system32/Boot/winload.exe status: 0xc000000f" info: the selected entry could not be loaded because the application is missing or currept

    I would appreciate any help/advice/pointers for this problem...

    Thank you

    Guy - FYI

    The problem is resolved.

    It was a prob with the std HP recovery disk such that it comes with the default display driver. But my laptop had NVIDIA GeForce 8400 M GS and the drivers where missing in the original disc. I ordered the HP disk drivers. After that the installation was smooth though it took almost seven hours for a recovery complete.

  • Satellite M40X-189 - replace HARD disk - what size should I go to?

    Hi, I have a SATELLITE M40X-189, I would like to replace the hard drive and would like if possible some recommendations!
    I know I need an ide/pata and I currently have a hard disk of 40 GB hitachi 5400 rpm installed. The memory is just what came installed originally, (512 MB, no upgrade).

    So what size I can up to?
    I have a lot of music/photos and video to change so must also size decent 80 GB would be enough?
    I really don't use it for anything other than that, and also the navigation on the internet. Although I often have a few programs running at the same time which causes problems... freeze, (in particular I tunes) and generally slow running.

    I'm confident on the physical replacement, and I know how to clone my old drive hard etc, but just need some info about the size and speed and if possible
    a recommendation of the manufacturer. Just worried about incompatibility really issues.

    Also, if you think I should install more memory, which size and make and model may recommend.

    Thank you in advance!

    Denise.

    Hi mate

    First he must know that this question have been posted a lot of time in the forum.
    If you want to use the search option, then you will find this thread for example:
    http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?MessageID=68287

    Is the M40X series supports the IDE controller and I think that you need a 2.5 IDE HDD.
    The old ide controllers are limited to 128 GB with 28-bit LBA
    However, you can take an 80 GB or 120 GB HARD drive and it should work fine

    Welcome them

  • hard disk crash (intelligent control error 0303) cannot use the recovery

    I have a hp pavilion dv6-6050 and it crashed suddenly I can't use recovery option, because it cannot read hard drive

    I tried to connect the hard drive to another pc via sata-usb cable and the other pc has detected hard disk read errors

    How do I return the recovery partion so I can use it on a new hard drive

    Hello:

    You will not be able to.  When the disc is dead, it took the recovery with her partition.

    You will need to order a set of recovery discs, and they can only be used if you buy a hard drive of the same size or more large storage capacity than the one who died on you.

  • Replacement hard disk for Satellite A30 921

    I have a satellite A30 921, which is a model and I need a replacement hard drive, could someone please recommend that it would be better for me. The model also comes with a 40 GB hard drive is possible to update with this model. Thank you

    I agree with Akuma. You can try using the drive HARD IDE 2.5 up to 100-120 GB.
    I think that by using a 100 GB shouldn't t be a problem

  • Outlook Express could not be started. The application was unable to initialize the store directory. Your computer may be out of memory or your disk is full. Error code: 0 x 80007114

    Operating system Windows XP, at startup, I get the message: "Outlook Express could not be started. The application was unable to initialize the store directory. Your computer may be out of memory or your disk is full"and displays the error code: 0 x 80007114.  (I have a new drive hard with enough space) Outlook Express always open well and functioning normally.  The message mentions and how to fix the problem?  Thank you, Rick

    Jump here (nothing Bruce suggested is false), I did a search and found this old article (http://support.microsoft.com/kb/245419), which indicates that there is a bad entry under the identity key in the registry (see www.oehelp.com/backup.aspx for background).  So if it's a big problem, you can do the steps suggested in this article and that will fix it.  Or if you have just one account, then backup your settings and the identity key and then delete the identity key and then start OE and it will establish a new, and you can then set up your account again, and then import the messages from the older directory.  But it does not indicate the major corruption, so you can just ignore it.

    Steve

  • Essential Microsoft Security Update error code

    Whenever I try to update my antivirus (Microsoft Security Essential) an error comes

    Error code: 0 * 80070422

    Error Description: Microsoft Security essential can not start the update service because it has been disabled by the local administrator or as a result of problem in the registry data.

    Please give me the solution or another site to download updates.

    Quote your full version of Windows (for example, WinXP SP3;) Windows XP 64 - bit SP2; Vista SP1; Vista 64 - bit SP2; Win7; Win7 64 bit) when you post in a forum or a newsgroup. Please do it in your next reply.

    Windows Update error 80070422:
    http://Windows.Microsoft.com/en-us/Windows7/Windows-Update-error-80070422

    How to reset the Windows Update components?
    [Skip the section to APPLY to; run Fix It in default and aggressive mode]
    http://support.Microsoft.com/kb/971058

    When (date about) don't you install Microsoft Security Essentials (MSE)?

    What antivirus application was installed before you installed MSE, was your subscription always news, and did you uninstall it before installing MSE?

    A (another) Norton or McAfee application ever been installed on the computer (for example, a free trial version which is preinstalled when you bought it)?

    =================

    I can't install Microsoft Security Essentials to clean my already infected computer?
    http://social.answers.Microsoft.com/forums/en-us/msescan/thread/87058857-D181-4019-a723-efd9a49d9275

    Support Microsoft Security Essentials forums
    http://social.answers.Microsoft.com/forums/en-us/category/MSE

    ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

  • Important updates for Vista SP2 Security Installation failure: update MSXML 4.0 SP2 (KB927978) AND (KB954430) security, citing error Code 652, Windows Update encountered an unknown error!

    Has no significant updates for VISTA SP2 security installation: MSXML 4.0 SP2 (KB927978) security AND (KB954430), citing error Code 652, Windows Update encountered an unknown error! How is it Windows Update does not recognize it's own mistakes? I tried several times to install both of these important updates without success. Please help me so that I can install these two updates & get back on the right track. Thank you!

    See the section "How to get help", for example, http://support.microsoft.com/kb/927978

    Visit the Microsoft Solution Center and antivirus security for resources and tools to keep your PC safe and healthy. If you have problems with the installation of the update itself, visit the Microsoft Update Support for resources and tools to keep your PC updated with the latest updates.

    For enterprise customers, support for security updates is available through your usual support contacts.

    ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

  • Failure to install Windows security update, error code 800706BA and 800706BE

    Several updates failed to install last week Windows security.  800706BE and error code 800706BA were cited as the problem.

    How can I fix it?

    Hi Libra1949,

    ·         Did you do changes on the computer before the show?

    ·         (Numbers KB) updates you install?

    ·         You are able to install other updates successfully?

    Follow these methods.

    Method 1: Temporarily disable the security software .

    Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks.

    Method 2: Put the computer in a clean boot State to see if there is a software conflict as the clean boot helps eliminate software conflicts.

    Note: After completing the steps in the clean boot troubleshooting, follow the link step 7 to return the computer to a Normal startupmode.

    Method 3: You can also manually install updates (KB number) by downloading from the Microsoft Download Center.

    http://www.Microsoft.com/downloads/en/default.aspx

    Method 4: Follow the steps in the article.

    How to reset the Windows Update components?

    You cannot install some programs or updates

Maybe you are looking for