failed to start - read/write failure\rstrui.exe

Similar Questions

• Help... I can't get passed the screen that reads... Memory read/write failure at 39460F84, read A9468946 waiting for A946A946 to fix this problem, try reinstalling the memory. Decrease in available memory

  I have just completed the removal of the entire contents of my computer and was happily back in line when this screen popped up and now I am unable to go beyond this. To make it worse, I have a game disc in and he's not out there either, I'm at a total loss as to how to proceed.

  Hello

  The question could be linked to the material, so I suggest you contact the manufacturer of the computer for better assistance.

• [ERROR] ISO [DAAPI] =-1: [I2C] failed to start the write operation: errno = 11

  As this bug is pretty boring, I expect the GA 8 final Java ME will be corrected this. Are there plans when it will be available to the public?

  Hi Markus,.

  This bug has been fixed in drops later.

  / Sergey

• failed to read/write memory

  I would'nt be the smartest on the laptop, and rather than take it to get repaired, once again, I would be grateful if someone could help me. I have a dell inspiron XPpro.when I turn on that I get the error codes memory read/write failure@1FFF1DC8,read FF12FF10 expecting10FF10.memory line failure@1FFF0000,read F10FF10, expecting00000000.memory read/write failure10000000, read00ED00EF, expecting00EF00EF running. Have tried the system restore, but it goes up to the start-up of the fault. I get into windows by pressing F1. It took forever to make that the system is slow and freezes. I read the forum and would have tried to reinstall windows but can not find the disc, I did not have the registration number of the sticker. I would be grateful for any help, even if just to tell me to take it to an expert.

  Hello

  When exactly do you get this error? When you start the computer or after you start?

  Check out the link and follow the steps.
  How to perform disk error checking in Windows XP
  http://support.Microsoft.com/kb/315265
  Important: Running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data may be lost
  If the problem persists, then you can contact the manufacturer of the computer

• Vista Ultimate does not start: c:\windows\system32\ntkrnlpa.exe is corrupt failed error code = 0 x 2

  All of a sudden I started my laptop and Windows does not load.  I received a message "failed to nobulate".  I searched in the help forums and found that I could create a boot CD (because the OS came preinstalled on Dell INspiron 1720 laptop computer).  I tried to perform a Startup Repair 11 times.  The repair details show:

  Boot critical file c:\windows\system32\ntkrnlpa.exe is corrupt failed error code = 0 x 2

  I also tried to visit the advanced repair and selecting to restore from an earlier point in time, but I relieve error that no previous points are detected.

  Help, please!  I '; ve been against a week and need back up and going.  Thank you!

  Sue

  Dell recovery options:

  http://supportapj.Dell.com/support/topics/global.aspx/support/DSN/en/document?journalid=67E9C215C4BABD6CE040AE0AB5E14F05&docid=339949

  Above is Dell to reinstall Vista from the DVD on your computer.

  http://supportapj.Dell.com/support/topics/global.aspx/support/DSN/en/document?journalid=67E9C215C4BABD6CE040AE0AB5E14F05&docid=336966

  And that way if you have a recovery partition on your hard drive.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Data recovery:

  1. slave of your hard drive in another computer and read/save your data out there.

  2. put your Hard drive in a USB hard drive case, plug it into another computer and read/save from there.

  3 Alternatively, use Knoppix Live CD to recover data:

  http://www.Knopper.NET/Knoppix/index-en.html

  Download/save the file Knoppix Live CD ISO above.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://isorecorder.alexfeinman.com/isorecorder.htm

  Download the Vista software from the link above.

  After installing above ISO burning software, right click on the Knoppix ISO file > copy the Image to a CD.

  Knoppix is not installed on your PC; use only the resources of your PC, RAM, graphics etc.

  Change the boot order in YOUR computer/laptop to the CD/DVD Drive 1^st in the boot order.

  Plug a Flash Drive/Memory Stick, BOOT with the Live CD, and you should be able to read the hard drive.

  When the desktop loads, you will see at least two drive hard icons on the desktop (one for your hard drive) and one for the USB key.

  Click on the icons of hard drive to open and to understand which drive is which.

  Click the icon for the USB drive and click on "Actions > Change the read/write mode" so you can write to disk (it is read-only by default for security reasons).

  Now to find the files you want to back up, just drag and drop them on the USB. When you're done, shut down the system and remove the USB key.

  See you soon

  Mick Murphy - Microsoft partner

• ORA-27070: async read/write failed

  Hello
  10 g R2 on Win server 2008 my faile overlap RMAN backups when:

  run
  10> {
  11>      allocate channel t3 type disk;
  12>      backup as compressed backupset format '\\ASERVER\SAV-DAT\RMAN\INCR\MYDB\df_%d_%T_%s_%p' INCREMENTAL LEVEL 1 database;
  13>      sql 'alter system switch logfile';
  14>      backup as compressed backupset format '\\ASERVER\SAV-DAT\RMAN\INCR\MYDB\al_%d_%T_%s_%p' archivelog all delete input;
  15>      backup as compressed backupset format '\\ASERVER\SAV-DAT\RMAN\INCR\MYDB\ctl_%d_%T_%s_%p' current controlfile;
  16> }
  17> host "DIR \\ASERVER\SAV-DAT\RMAN\FULL\MYDB\DF_MYDB*";
  18> crosscheck backup;
  19> delete obsolete;
  20> delete expired backup of database;
  21> 
  22>   
  Finished backup at 01-SEP-10
  
  Starting backup at 01-SEP-10
  channel t3: starting compressed full datafile backupset
  channel t3: specifying datafile(s) in backupset
  including current control file in backupset
  channel t3: starting piece 1 at 01-SEP-10
  channel t3: finished piece 1 at 01-SEP-10
  piece handle=\\ASERVER\SAV-DAT\RMAN\INCR\MYDB\CTL_MYDB_20100901_98_1 tag=TAG20100901T205836 comment=NONE
  channel t3: backup set complete, elapsed time: 00:00:03
  Finished backup at 01-SEP-10
  released channel: t3
  
  host command complete
  
  allocated channel: ORA_DISK_1
  channel ORA_DISK_1: sid=103 devtype=DISK
  RMAN-00571: ===========================================================
  RMAN-00569: =============== ERROR MESSAGE STACK FOLLOWS ===============
  RMAN-00571: ===========================================================
  RMAN-03009: failure of crosscheck command on ORA_DISK_1 channel at 09/01/2010 20:59:58
  ORA-19501: read error on file "\\ASERVER\SAV-DAT\RMAN\FULL\MYDB\DF_MYDB_20100825_22_1", blockno 1 (blocksize=8192)
  ORA-27070: async read/write failed
  OSD-04016: Error queuing an asynchronous I/O request.
  O/S-Error: (OS 64) Net Work name unavailaible
  ORA-19501: read error on file "\\ASERVER\SAV-DAT\RMAN\FULL\MYDB\DF_MYDB_20100825_22_1", blockno 256 (blocksize=8192)
  ORA-27070: async read/write failed
  OSD-04016: Error queuing an asynchronous I/O request.
  
  Recovery Manager complete.

  As yo see RMAN backup finishes but defective during overlap. The file is available and can be connected to the CARRYING by RMAN to write the file. Why can't it overlaps?
  
  Thank you.

  Why can't it overlaps?

  S/O-error: name of Net work (OS 64) unavailaible

• Lsass.exe - Unable to locate component. This application has failed to start because the oleaut32.dll file not found

  Original title: oleaut32.dll xp

  My system XP pro/sp3 does not start normally, without danger or with the original sys disk. I get a message
  Isass.exe - Unable to locate component. This application has failed to start because the oleaut32.dll file not found. reinstalling the application may fix this problem.
  However, I can't in the operating system to do a re-install.
  Any suggestions?

  If c:\windows\system32\oleaut32.dll is missing, you will see messages like this:

  Lsass.exe - Unable to locate component
  This application has failed to start because the OLEAUT32.dll file not found.  Reinstalling the application may fix this problem.

  If the missing file is the only problem, you might have to do a reinstall to fix.

  There should be a copy of Oleaut32.dll in the c:\windows\system32\dllcache folder, so if you can get in the XP Recovery Console, you can just replace it - then you are going to have to start on something to do.

  Once started in the XP Recovery Console, you must enter this command at the prompt:

  Copy c:\windows\system32\dllcache\oleaut32.dll c:\windows\system32

  If the file is not in the dllcache folder (it should really be), depending on your installation, this command can work:

  Copy c:\windows\servicepackfiles\i386\oleaut32.dll c:\windows\system32

  Answered in the affirmative if invited to replace any existing file.

  I don't know what the Microsoft Support Engineer think that KB307545 or KB922371 will help you.  I think that the MSE is just throw a few things to try and some links.  You don't describe symptoms consistent with the need to use one of these methods.   I would say the MSE has never seen this problem before, made no attempt to reproduce the problem, and has no idea how to fix this.

  If your CD does not start in the Recovery Console, or if you don't know what kind of CD do you have to do a CD of XP Recovery Console and boot on it (no media XP required).

  Here's how:

  Boot into the Recovery Console Windows using an XP bootable installation CD.

  If you have no XP bootable media (or aren't sure you have) create a bootable XP Recovery CD of Console and do not forget.

  This is not the same as recovery disks that might have come with the acquisition of the system store.

  You can make a bootable Recovery Console CD by downloading an ISO file and burn it to a CD.

  The ISO bootable image file you need to download is called:

  xp_rec_con. ISO

  Download the ISO from here:

  http://www.mediafire.com/?ueyyzfymmig

  Use a new CD and this simple and free program to burn your ISO file and create your bootable CD:

  http://www.ImgBurn.com/

  When you install ImgBurn, DO NOT install the Ask toolbar.

  Here are some instructions for ImgBurn:

  http://Forum.ImgBurn.com/index.php?showtopic=61

  It would be a good idea to test your bootable CD on a computer running.

  You may need to adjust the computer BIOS settings to use the CD-ROM drive as the first device to boot instead of the hard drive.  These adjustments are made before Windows tries to load.  If you miss it, you will need to restart the system again.

  When you start on the CD, follow the instructions:

  Press any key to boot from CD...

  Installing Windows... going to pronounce.

  Press 'R' to enter the Recovery Console.

  Select the installation that you want to access (usually 1: C:\WINDOWS)

  You may be asked to enter the password (usually empty).

  You should be in the folder C:\WINDOWS.  It's the same as the

  C:\Windows folder that you see in Solution Explorer.

  The Recovery Console allows base as file commands: copy, rename, replace, delete, chkdsk, fixboot, fixmbr, cd, etc.

  For a list of the commands in the Recovery Console, type help at the prompt of commands or read on here XP Recovery Console:

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/recovery_console_cmds.mspx?mfr=true

  After replacing the file, remove the CD and type 'exit' to leave the RC and restart the computer.

  You have not to set the BIOS to boot the disk HARD since the CD won't be.

• WINDOWS 7 error the application failed to start because the side by side configuration is incorrect, please see the application event log or use the command-line sxstrace.exe for more details.

  «WINDOWS 7 error the application failed to start because the side by side configuration is incorrect, please see the application event log or use the command-line sxstrace.exe for more details.»

  This cams almost for all the applications that I try to open. I read all kinds of things to solve problems, but I can't install anything because it is constantly on the screen.

  I think it's like that because my computer shuts off when I was doing the system restore, because he has not started.

  I don't know what to do.

  Hello

   
  You can view the event log by using Event Viewer. See the link below for more information about how to use Event Viewer to check the error message or information,
  http://Windows.Microsoft.com/en-us/Windows7/what-information-appears-in-event-logs-Event-Viewer
   
  Please check the information in Event Viewer and let us know the problem more briefly for a better solution.
   
  
  Method 1:
  However, try the SFC (System File Checker) scan on the computer. Check out the following link to do the same thing:
  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7
  http://support.Microsoft.com/kb/929833
   
  Method 2:
  You try to run the fixit given in the following link and check if it works:
  http://support.Microsoft.com/mats/Program_Install_and_Uninstall/

   

  Method 3:

  You have recently updated with Microsoft Visual C++?

  http://social.technet.Microsoft.com/forums/en/itprovistaact/thread/5491a46a-57f4-444D-a1fd-2600fa6d587e

  I hope this helps!

• Error 'nmapp.exe.unable to locate the component. This application has failed to start because MSVCP 70 .dll is not found"when you connect to the computer.

  Original title:

  Problem: I use DeLL Desktop.When I connect, these messages appear on my screen: nmapp.exe.unable to locate the component. This application has failed to start because MSVCP 70 .dll not found. Re-installing the application may fix the problem. Pls help. Thank you.

  Hello
  1. what version of Windows is installed on the computer?
  2. are you aware of any changes made to the computer, before the show?
  Assuming you have Windows Vista or Windows 7, follow the steps mentioned below.

  Method 1:
  

  Step 1: Perform a boot minimum troubleshooting and check which application reports this error
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135
  Note: once you have determined the problem by using a clean boot procedure, follow step 7 in the article to restore your computer to normal startup.

  Step 2: reinstall the application.
  Uninstall or change a program
  http://Windows.Microsoft.com/en-us/Windows7/uninstall-or-change-a-program

  Method 2:
  Run an analysis of auditor of system files on your computer and check for the issue.
  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7
  http://support.Microsoft.com/kb/929833

  I hope this helps.

• Error: mmc.exe - Unable to locate component. This application has failed to start because apphelp.dll was not found.

  Original title: this application has failed to start because apphelp.dll was not found.

  A window titled "mmc.exe - Unable to locate component" in the title bar, which includes the message:

  "This application has failed to start because apphelp.dll was not found.  Reinstalling the application may fix this problem. »

  that appears when you access many of the 'administration tools' in the start menu.  e.g. component, computer, event viewer Management Services, etc.

  I'm afraid I accidentally deleted apphelp.dll when cleaning on other files.  I found copies of apphelp.dll in following two tracks.

  AppHelp.dll C:\WINDOWS\$NtServicePackUninstall$ 124KO Extension Application 09/08/2004

  AppHelp.dll C:\WINDOWS\ServicePackFiles\i386 123KO Application Extension 04/13/2008

  I tried Recuva, but he could not find the file.

  How to re - install a such apphelp.dll suggested by the pop - up error message window?

  Thank you

  I thought it would be something that began with "A".

  For low overhead and free, think of Microsoft Security Essentials (MSE).

  MSE and a regularly good scan with the definitions updates using MBAM and SAS (from post above) should keep you in good shape according to your Internet habits.

• logon error: Hphmon06.exe could not be located. the application has failed to start because hpzjrd01.dll is not found.

  Original title : I get... suite msg on logon: Hphmon06.exe not found in windows xp.  the application has failed to start because hpzjrd01.dll be found.

  Someone else already has this nagging and ongoing problem?  How to solve this?

  glenkelly,

  If you are just wanting to get rid of the annoying popup, try the following steps:

  -Click on the Start button
  -Click on run...
  -In the "Run" dialog box... ", type: msconfig
  -It will jump to the top of the window "System Configuration"
  -In the window "System Configuration", select the tab "start".
  -In the first column (startup item), Ahmed to the bottom of the list and search for "Hphmon06.exe."
  -(Ex: «Startup Item»---«Hphmon06»)
  -If you are unable to locate this name, expand the column "order."
  -In respect of the 'Command' column, scroll down and look for the path 'Hphmon06.exe '.
  -(Ex: «Command»---«C:\Program Files\Fichiers Files\HP\hphmon06.exe»)
  -Uncheck the question to the left of the box, and then click 'OK '.
  -More than likely, a box will appear asking if you want to "Reboot now" or "restart later".
  -Click "Restart now" and see if the popup box boring will disappear when you connect!

  -Riley

• "SiSUSBrg.exe.exe - Unable to locate component" appears at startup. "This application has failed to start because SIS_Lib.dll is not found."

  Original title: SiSUSBrg.exe

  "SiSUSBrg.exe.exe - Unable to locate component" appears at startup. "This application has failed to start because SIS_Lib.dll is not found."

  Hope that this is not a virus!  Help?

  Hello

  I suggest you to follow these steps and check if that helps:

  Method 1:
  Start the computer in safe mode and check if the same problem occurs:
  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/boot_failsafe.mspx?mfr=true

  Method 2:
  Try to perform the clean boot and check if it helps:
  http://support.Microsoft.com/kb/310353
  NOTE: When you are finished troubleshooting, make sure that you reset the computer in start mode normal such as suggested in step 7 of the above article.

  It will be useful.

• Error: ApopleSyncNotifier.exe. Application has failed to start because Core Foundation.dll not found in the system startup

  Original title: AppleSyncNotifier.exe and RUNDLL

  When I boot I get 2 drop down boxes 1 to ApopleSyncNotifier.exe.  Application has failed to start because Core Foundation.dll not found.  Re-Setup, the application may resolve the problem.

  RUNDLL error loading C:\WINDOWS\nulogry.dll.  The specified module could not be found.

  How can I fix them?

  Hi saintaugie,

  1. have you installed any Apple Sync program on the computer?

  We found that this happens if MobileMe on the computer is defective. To resolve this problem, we recommend that you uninstall MobileMe and check if the problem persists.
  a. to see How to change or remove a program in Windows XP
  b. in the list select MobileMe and uninstall it.
  c. restart the computer once the program is uninstalled.

  We found the same problem on the Apple Forums.
  See Impossible to locate the CoreFoundation.dll AppleSyncNotifier.exe error
  

  Note: You might consider to reinstall the program if you need. However, we do not recommend to install non-Microsoft programs as Microsoft has not tested the feature.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• The application has failed to start because Qtcore4.dll not found. So Daemonprocess.exe has a stop

  I use a vista laptop (32-bit OS) window when I log in, these messages, "the application has failed to start because Qtcore4.dll not found."  And so Daemonprocess.exe has a stop. Hope u could help me solve this problem. Thank you.

  Gary Goh

  Goh Hey! I had the same problem.  It is caused by moboengine software.  This has happened with me after you have uninstalled it.

  Navigate to C:\program files (x 86) \moboengine and remove this directory, make sure that you have killed the daemonprocess.exe execution program in your first task manager ;)

• C:/ProgramFiles/Windows Live/Messenger/msnmsgr.exe the application has failed to start

  I would like to be able to open Windows Live Messenger.

  C:/ProgramFiles/Windows Live/Messenger/msnmsgr.exe

  The application has failed to start because its side-by-side configuration is incorrect.
  Check the log of events applications for more details.

  How can I fix it?

  This forum is for the installation and the upgrade of Windows itself.  Please ask in the forums of Messenger to

  http://windowslivehelp.com/product.aspx?ProductID=2&version=15.3.2804.0607