Failed to start remote access service

Hello

I get a vps and I install ca and iis and the remote access service

I allow it as a vpn server

When I try to run the remote access service there gives me an error

The Routing and remote access is dependent on the Remote Access Connection Manager service, which could not start due to the following error:

The dependency service or group was able to start.

I reslove this problem to run these commands:

netcfg u ms_sstp

netcfg - c p-i ms_sstp.

net start sstpsvc

net start rasman

now when I am tempted to throw there gives me this error:

The Remote Access Connection Manager service terminated with the following error:

The system cannot find the specified device.

So what is the problem?

Thank you.

Hello

Your question of Windows is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the Microsoft TechNet forum. You can follow the link to your question:

http://social.technet.Microsoft.com/forums/en-us/categories

Tags: Windows

Similar Questions

  • Failed to start Remote Access Connection Manager Service. Get the 20 error: the system cannot find the specified device.

    This seems to have started with the last batch of updates of Windows 7 (including SP1).
    I can't connect using dial-up.  Get the message:
    Cannot load the Remote Access Connection Manager service
    Error 711: The operation could not complete because it could not start the remote access connection manager service
    in time.  Please try the operation again.

    When I try to start the Remote Access Connection Manager service manually, I get the message:
    Windows could not start the service on Local computer remote access connection manager.
    20 error: the system cannot find the specified device.

    My phone displays the modem works properly, and telephony and the Secure Socket Tunneling Protocol service started.

    I don't know what else might have changed.

    Hello Vince_867,

    Thanks for your post.  Take a look at this thread for a possible solution to your problem.

    See you soon

  • Where can I get a download for Windows XP Service Pack 3 disc? I remote access service and cannot download it online.

    PeoplePC disconnected until the download is complete; Therefore, it loses data downloading and Service Pack 3 does not boot to Windows. Computer must be retrieved from partition-all installed programs must be re-installed or downloaded again. It takes some days with the remote access service.

    You can order a CD from Microsoft or download online.

    "How to obtain the latest Service Pack for Windows XP"
    HTH,
    JW
  • Failed to start remote service of hyperion

    In the same area, I can ping the server, and I use sc \\servername start hypservicename to start a remote server service and get the error saying: the specified service does not exist. but I know that there is not, what's wrong with me?

    You enter just the name of the server or using \\servername, she will be like: -.
    SC \\hypserver start HyS9SharedServices

    See you soon

    John
    http://John-Goodwin.blogspot.com/

  • Can not get to start remote access connection manager and the connections don't work Internet

    Original title: wired & wireless connections does not.

    I can not get the remote access connection manager to start and so no internet connection is not working, also I can't open the system restore to go back on this machine. What is this?

    I am running a Dell Studio 1735 PP31L w model number / Edition Vista Home premium.

    Hi Rick,

    1. what happens when you try to start the remote access connection manager? You receive messages or error codes?

    2. you receive error codes or restore messages when you perform the system?

    You can check the status of the following services and make sure that the services are started.

    a. Click Start and type Services in start search and press ENTER.

    b. in the services with the right button on the phone and then click Properties.

    c. under the general tab, select automatic next to startup type.

    d. under the general tab, click Start under the service status and then click apply and then click OK.

    e. Repeat steps c & d to the remote access connection manager and Remote Access Auto Connection Manager service.

    Hope this information is useful.

  • Why can't I start Remote Access Connection Manager

    I am not able to connect to internet using my 3G Broadband. I try to resolve the status of the remote access connection manager to "on the road", but the error message invites up to said "Windows could not start the service on local computer remote access connection manager. Error 1068: the dependency service or group could start. "I find the dependencies are Remote Access Auto Connection Manager, routing and remote access, Sharing (ICS) to connect Internet. I tried to put those 3 to "started", but was able to start also.

    Hello
     
    You must make sure that the underside of services are started and restart your computer and check if the problem is resolved.
     
    To start the services.
     
    1. click on start.
    2. type Services.msc in the search box and click on enter.
     
    Note: the common addiction for "Remote Access Connection Manager" and 'Remote Access Auto Connection Manager' is 'Secure Socket Tunneling Protocol Service'.
     
    Make sure that you check the properties of service no matter what you try to start, then click the dependency tab and make sure that you select the dependency registered under this service services.
     
    The dependency of 'Remote access connection manager' services include:
     
    a. secure Socket Tunneling Protocol Service
    b. phone
    c. Plug-and-Play
    d. remote Procedure Call (RPC)
    e. DCOM Server process Launcher
    f. RPC end point mapper
     
    Make sure that you try to start the Connection Manager Service dependency services automatic remote access as well.
     
    Method 2:
     
    I recommend you to update the drivers and see if it makes a difference. You must be logged on as administrator to perform these steps.
     
    1. open Device Manager by clicking the Start button, click on the Control Panel, clicking system and Maintenance, and then clicking Device Manager. If you are prompted for an administrator password or a confirmation, type the assword or provide confirmation.
    2. in Device Manager, locate the device, and then double-click the device name.
    3. click Driver tab, then click on set to update driver and follow the instructions.
     
    Try to follow the link provided to update a hardware driver that is not working properly and check the question below.
    http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

    Thank you, and in what concerns:
    I. Suuresh Kumar - Microsoft technical support.

    Visit our Microsoft answers feedback Forum and let us know what you think.

  • Get the error 'windows' failed to start the spooler service on local computer, error 1075 printing when you try to install a printer.

    Hi, printer "spooler".

    IM using widows vista, I had a problem installing my printer, can not install because that the problem with 'spooler service', followed the advice of microsoft and went to services, a window apears, "windows could not start the spooler service on local computer, error 1075 printing;"the dependency service does not exist or has been marked for deletion"can help you please?

    Hello pedro,

    We will remove and reinstall the printer:

    1. remove the printer from the PC.

    2 uninstall the printer from the PC driver.

    3 reinstall the printer driver.

    4 reinstall the printer.

    Also, here are some links about printing reference:

    Open the printer Troubleshooter

    http://Windows.Microsoft.com/en-us/Windows7/open-the-printer-Troubleshooter

    Why can I not print?

    http://Windows.Microsoft.com/en-us/Windows7/why-cant-I-print

    Find and install printer drivers

    http://Windows.Microsoft.com/en-us/Windows7/find-and-install-printer-drivers

  • Failed to start the Schedule Service

    We were able to install and configure the space of work/Shared Financial Services, Essbase, Planning, Reporting, health and SAFETY in our new 11.1.2.5 environment, all running on Red Hat Linux 5.8.  However, when we try to start the schedule service, it gets stuck in a State of "Admin" and we cannot connect to it.  Troubleshooting tips are greatly appreciated.

    Thank you in advance.

    The admin State is most of the time related to the issue of the database. Please paste the logs and see if you can connect directly to the planning scheme.

  • "Failed to start the sharing service connection of Windows Firewall/Internet (ICS) on local computer. Error 5: access is denied. »

    I had a problem with a virus earlier. I had the problem for most supported but now my firewall is disabled, and whenever I try to turn it on I get this error message. I don't know what to do, I have tried everything I can think of exscept a complete re - format. In addition to that my audio drivers keep uninstall themselves every hour or so sometimes he finally a little more. I tried everything I could to remedy these problems, but nothing has worked.

    Hello purple squirrel.

    You can try to do a upgrade in Place or repair your operating system to Windows XP.
    Click the number of the KB article to bring up instructions to complete an upgrade in Place.

    KB Article ID: 978788 -how to perform an upgrade on the spot (reinstallation) of Windows XP
    You will need to have a Windows XP CD and your product ID to reinstall. It is a long process. You won't have to reinstall programs, but you will
    you need to reinstall the Service Packs and Windows updates.
    Be sure and print the item for you reference, and be sure you understand what is needed before starting the repair.
    Please let us know if we can help with any questions.
    Thank you

    Marilyn
    Microsoft Answers Support Engineer
    Visit our Microsoft answers feedback Forum and let us know what you think

  • Remote Access Service Console

    Is there a way to access the VMware host service console remotely?

    Try to run the command "dcui" in an SSH session...

    Direct Console User Interface (DCUI) since a SSH session access (2039638). VMware KB

    / Rubeck

  • Failed to start Security Center service

    The four security essentials are disabled.  When I try to put it on, it gives a notification saying that the security service center can not be started.

    Hello

    If you want the best possible support here, you have to tell us what operating system you are using and the events that led to what happens to the problem.

    Download, install, update and scan your system with the free version of Malwarebytes AntiMalware:

    http://www.Malwarebytes.org/products/malwarebytes_free

    See you soon...

  • The Routing and remote access could not start, error 214500037 (0x80004005)

    My windows server 2003 r2, failed to start the Routing and remote access services. And in the event an observer log, it has error code
    Event ID: 7024, with service specific error 2147500037 (0x80004005)
    I tried to reset tcp/ip and replace ias.mdb and dnary.mdb by a new, but it did not work.

    Thank you

    Hi budhihartono,

    Since you are facing problems with windows server 2003 r2, it would be better suited in the Technet Windows forum. Please post your question in the following TechNet Windows server forum to improve assistance:

    http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

  • ASA 5505 - remote access VPN to access various internal networks

    Hi all

    A customer has an ASA 5505 with a remote access vpn. They are moving their internal network to a new regime and that you would be the users who come on the vpn to access the existing and new networks. Currently can only access the existing. When users connect to access remote vpn, the asa gave them the address 192.168.199.x. The current internal network is 200.190.1.x and that they would reach their new network of 10.120.110.x.

    Here is the config:

    :

    ASA Version 8.2 (5)

    !

    ciscoasa hostname

    enable encrypted password xxx

    XXX encrypted passwd

    names of

    !

    interface Ethernet0/0

    switchport access vlan 2

    !

    interface Ethernet0/1

    !

    interface Ethernet0/2

    !

    interface Ethernet0/3

    !

    interface Ethernet0/4

    !

    interface Ethernet0/5

    !

    interface Ethernet0/6

    !

    interface Ethernet0/7

    !

    interface Vlan1

    nameif inside

    security-level 100

    IP 200.190.1.15 255.255.255.0

    !

    interface Vlan2

    nameif outside

    security-level 0

    IP address 255.255.255.0 xxxxxxx

    !

    exec banner the ACCESS NOT AUTHORIZED IS STRICTLY PROHIBITED

    connection of the banner the ACCESS NOT AUTHORIZED IS STRICTLY PROHIBITED

    banner asdm the ACCESS NOT AUTHORIZED IS STRICTLY PROHIBITED

    passive FTP mode

    access extensive list ip 200.190.1.0 inside_access_in allow 255.255.255.0 any

    outside_access_in list extended access permit icmp any external interface

    access extensive list ip 192.168.199.0 outside_access_in allow 255.255.255.192 host 10.120.110.0

    Standard access list MD_IPSEC_Tun_Gp_splitTunnelAcl allow 200.190.1.0 255.255.255.0

    MD_IPSEC_Tun_Gp_splitTunnelAcl list standard access allowed host 10.120.110.0

    access extensive list ip 200.190.1.0 inside_nat0_outbound allow 255.255.255.0 192.168.199.0 255.255.255.192

    inside_nat0_outbound list extended access allowed host ip 10.120.110.0 192.168.199.0 255.255.255.192

    pager lines 24

    Enable logging

    asdm of logging of information

    Within 1500 MTU

    Outside 1500 MTU

    mask 192.168.199.10 - 192.168.199.50 255.255.255.0 IP local pool Remote_IPSEC_VPN_Pool

    IP verify reverse path to the outside interface

    ICMP unreachable rate-limit 1 burst-size 1

    ICMP allow any inside

    ICMP allow all outside

    don't allow no asdm history

    ARP timeout 14400

    Global 1 interface (outside)

    NAT (inside) 0-list of access inside_nat0_outbound

    NAT (inside) 1 200.190.1.0 255.255.255.0

    inside_access_in access to the interface inside group

    Access-group outside_access_in in interface outside

    Route outside 0.0.0.0 0.0.0.0 190.213.43.1 1

    Route inside 10.120.110.0 255.255.255.0 200.190.1.50 1

    Route inside 192.168.50.0 255.255.255.0 200.190.1.56 1

    Route inside 192.168.60.0 255.255.255.0 200.190.1.56 1

    Timeout xlate 03:00

    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

    timeout tcp-proxy-reassembly 0:01:00

    Floating conn timeout 0:00:00

    dynamic-access-policy-registration DfltAccessPolicy

    http server enable 10443

    http server idle-timeout 5

    Server of http session-timeout 30

    HTTP 200.190.1.0 255.255.255.0 inside

    No snmp server location

    No snmp Server contact

    Server enable SNMP traps snmp authentication linkup, linkdown cold start

    Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

    Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

    Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

    Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

    Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

    Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

    life crypto ipsec security association seconds 28800

    Crypto ipsec kilobytes of life - safety 4608000 association

    Dynamic crypto map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs

    Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

    outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

    outside_map interface card crypto outside

    Crypto ca trustpoint _SmartCallHome_ServerCA

    Configure CRL

    Crypto ca certificate chain _SmartCallHome_ServerCA

    certificate ca 6ecc7aa5a7032009b8cebcf4e952d491

    (omitted)

    quit smoking

    crypto ISAKMP allow outside

    crypto ISAKMP policy 10

    preshared authentication

    3des encryption

    sha hash

    Group 2

    life 86400

    Crypto isakmp nat-traversal 3600

    Telnet timeout 5

    SSH 200.190.1.0 255.255.255.0 inside

    SSH timeout 5

    SSH version 2

    Console timeout 5

    dhcpd outside auto_config

    !

    a basic threat threat detection

    scanning-threat shun threat detection

    Statistics-list of access threat detection

    no statistical threat detection tcp-interception

    WebVPN

    allow outside

    internal MD_SSL_Gp_Pol group strategy

    attributes of Group Policy MD_SSL_Gp_Pol

    VPN-tunnel-Protocol webvpn

    WebVPN

    list of URLS no

    disable the port forward

    hidden actions no

    disable file entry

    exploration of the disable files

    disable the input URL

    internal MD_IPSEC_Tun_Gp group strategy

    attributes of Group Policy MD_IPSEC_Tun_Gp

    value of banner welcome to remote VPN

    VPN - connections 1

    VPN-idle-timeout 5

    Protocol-tunnel-VPN IPSec webvpn

    Split-tunnel-policy tunnelspecified

    value of Split-tunnel-network-list MD_IPSEC_Tun_Gp_splitTunnelAcl

    the address value Remote_IPSEC_VPN_Pool pools

    WebVPN

    value of the RDP URL-list

    attributes of username (omitted)

    VPN-group-policy MD_IPSEC_Tun_Gp

    type of remote access service

    type tunnel-group MD_SSL_Profile remote access

    attributes global-tunnel-group MD_SSL_Profile

    Group Policy - by default-MD_SSL_Gp_Pol

    type tunnel-group MD_IPSEC_Tun_Gp remote access

    attributes global-tunnel-group MD_IPSEC_Tun_Gp

    address pool Remote_IPSEC_VPN_Pool

    Group Policy - by default-MD_IPSEC_Tun_Gp

    IPSec-attributes tunnel-group MD_IPSEC_Tun_Gp

    pre-shared key *.

    !

    !

    context of prompt hostname

    : end

    The following ACL and NAT exemption ACL split tunnel is incorrect:

    MD_IPSEC_Tun_Gp_splitTunnelAcl list standard access allowed host 10.120.110.0

    inside_nat0_outbound list extended access allowed host ip 10.120.110.0 192.168.199.0 255.255.255.192

    It should have been:

    Standard access list MD_IPSEC_Tun_Gp_splitTunnelAcl allow 10.120.110.0 255.255.255.0

    access extensive list ip 10.120.110.0 inside_nat0_outbound allow 255.255.255.0 192.168.199.0 255.255.255.192

    Then 'clear xlate' and reconnect with the VPN Client.

    Hope that helps.

  • On a 1100sa Pavilion DM4 how prevents one error message: unable to start Bluetooth stack service?

    I have a HP Pavilion DM4 1100sa, p/n: XE139EAR #ABU, a serial no: CNU1220Z75. I bought it about 2 weeks ago. Shortly after he stopped hibernating when I closed the lid and the fingerprint reader was also very intermittent, also error message unable to start Bluetooth stack service popped up after the computer has been rebooted and after startup of Internet Explorer... My own attempts to remedy that does not so I called your 0844 3690369 number and possibly your man said that the only option was to do a complete restore of the system. For this I made and then reinstalled my commercial software such as M/S Office 2010, Adobe Photoshop elements 9 etc.

    The error (see above) again reappeared and the fingerprint reader was still intermittent, also my Bluetooth mouse is not connected. Yet once, my own attempts to cure these problems have failed, including playback of your pages in the forum, so I phoned again, everything seems to be resolved but the initial problems and the subsequent, reappears.

    So I made an another System Recovery on Thursday, July 26, 2012. I did a full defragmentation and wiped the free space on the hard drive. This time, the only problem that occurs is the error message failed to start Bluetooth stack service. Yet once it appears only after a computer reboot and start Internet Explorer.

    I am very reluctant to spend another hour, or so, on the phone so I want your best and hopefully correct advice on how to avoid this very annoying message from popping up.

    Mike

    We will uninstall the system Broadcom bluetooth driver and that's it.

    We will not install another driver for this device instead.

  • Error 1068: the dependency service or group failed to start and failed to start the remote access connection manager service.

    Original title: Windows could not start the service of connection manager on the local computer remote access

    amplifier

    Windows could not start the service of connection manager on the local computer remote access

    Error 1068: The dependency Service or group could start.

    Hi sunelchandraoli,

    1. when exactly you receive this error?

    2. you remember to make changes to the computer before this problem?

    Step 1:

    "Make sure that all the services of the dependence of the"Remote Access Connection Manager"" are launched in the list of services...

    a. Click Start, type services.msc in the box start the search.

    b. select Services from the list programs. If you are prompted for an administrator password or a confirmation, type your password or click on continue

    c. right click on the Remote Access Connection Manager service and then click Properties.

    d. under the general tab, click Manual next to startup type.

    e. under the general tab, click Start under the service status and then click OK.

    f. also check for long-term services.

    The dependency of 'Remote access connection manager' services include:

    i. secure Socket Tunneling Protocol Service

    II. telephone

    III. Plug-and-Play

    IV. Remote Procedure Call (RPC)

    c. of DCOM Server process Launcher

    VI RPC end point mapper.

    Make sure that the above services are started in the services list. If this is not the case, start all services above and check.

    Step 2:

    You can also try a system restore to a prior restore point you have been affected by the issue.

    Note: When you perform the system restore to restore the computer to a previous state, programs and updates that you have installed are removed.

    To run the system restore, you can consult the following link:

    System restore

    http://Windows.Microsoft.com/en-us/Windows7/what-is-system-restore

    System Restore: frequently asked questions

    http://Windows.Microsoft.com/en-us/Windows7/system-restore-frequently-asked-questions

    Hope this information is useful.

Maybe you are looking for

  • com Apple.MRT

    Hello com Apple.MRT is flooding my log files such that it cannot be terminated. How can I fix? I found some clues on the WEB, but they do not work as I was unable to delete the job MRT Besides it's in for some reason, then removing doesn't seem to be

  • Save the distribution source for the previous version

    Hello I am trying to use the tool run a Labview VI in VBAI. I use LV2013 SP1 and VBAI 2013. The step run a VI Labview gives me an error saying "this step supports LV2012 or earlier. When I record to LV12, this time an error comes up saying "the VI ha

  • Digital output with NOR-9401 in cDAQ-9174

    Hello I have a cDAQ-9174 with an e/s digital NOR-9401 module. Now I want to output Digital signals on line0:3 $line0: Boolean 1 time = 10ms Line1: Boolean variable 1 time = 20ms row2: Boolean variable 1 time = 30ms line 3:20 pulses (period = 250us, d

  • What is a public update?

    Where it is defined? What is - this compared to CU, patch or SP? Thank you...

  • FND_STATTAB

    Hi allThank you in anticipation of your help.I'm trying to make a backup of this table FND_STATTAB, but I get an error: ora-01918; the user 'FND_STATTAB' does not exist.I desc the table and he shows me the description, here is my statement:create the