Fan of D4T - 1500 HP continuous switching speed between hi and lo

Similar Questions

• Satellite P10 switch randomly between battery and AC

  I have a satellite P10 who had some problems of strange power for about a year now.

  My laptop switch to the power of the battery even when it is plugged. I will then either use the computer until the battery runs out and turned it off or Hibernate in until the battery may charge.

  I thought that I had fixed by downloading and installing a new Bios from the toshiba site, which seemed to work for a while, but now it the problem seems to have returned.

  I also bought a new battery and the bar of power, thinking that was the problem... but it does not solve the problem.

  Someone else out there with similar problems, or a method to solve this?
  any thoughts would be great.

  Hi man,

  I had similar problems with my machine, so you can check some things:

  -When the CA is connected, then move him soft in all directions, there are maybe a few micro cracks on the AC connector.
  -try to boot your machine without the battery, your motherboard charging system is may be defective
  -Discover an another AC adapter, maybe the CA is defective

  If you encounter some strange phenomena as power cuts or no charge while you perform this action above, then you have definitely a hardware problem and you will need to contact your local dealer or the service partner for the other instance.

  So I had to do, and it's a faulty motherboard.

  Hope I could give you some ideas.

  Welcome them

• ESXi 5: speed between VM and host seems capped at 100Mbit

  Hello

  We are stumbling on a strange problem we have in our data center.

  Recently migrated all our guests to Esxi5 (HS22 blade in Bladecenter chassis IBM and DS3400 FC data store)

  All switches and ports on switches (virtual and physical) are synchronized at 1 Gbit/s duplex full.

  Internal driver E1000 driver fot the VM is.

  When we do a performance test, copy files or large network traffic associated action we get not over +/-10% of the capacity of port 1 Gbps.

  It seems that there is a component that traffic in 100 Mbps at max in mind.

  We have this behavior between hosts, but also on the single host between the virtual machine. (only traffic vSwitch)

  Is someone can give us a clue where to start?

  Thanks in advance!

  first thing to do is to go down the E1000 network driver.  It is the default NETWORK interface driver and not a right to use.  In most circumstances, you should use the VMXnet 3 driver, the performance is much better.  and is installed with vmware tools that you install in each VM

• Satellite A500-19N - Wlan switch between on and OFF in battery mode

  Hallo,

  I bought a new A500-19N Satellite three days ago and one have the problem,
  When I used the laptop battery, the wlan switch mode between connect and disconnect.
  With powersupplier, I have no problem.

  All energy wlan settings I adjusted to full performance and now I have now idea how can I solve the problem.
  Do you have any ideas or advice?

  Thank you very much
  Nico

  Hello

  You must verify power WLan settings in Win 7 power management and need to disable the power save for WLan in battery mode

  I found a great HowTo but for Vista OS.
  But the settings are not really different.

  Check this box:
  http://forums.computers.Toshiba-Europe.com/forums/Ann.jspa?annID=41

  Welcome them

• Shortcut to switch between Normal and preview

  What is the shortcut to switch easily between normal and forecast views?

  Thank you

  Luca

  « w ». By making sure, of course, that you do not have the text tool is active.

• Why the fan on my macbook pro continue to run at a fast pace for long periods?

  The MacBook Pro mid-2010

  OS X El Capitan, 10.11.3 version

  Processor: 2.4 GHz Intel Core 2 duo

  Memory: 4 GB 1067 MHz DDR3

  Graphics card: NVIDIA GeForce 320 M 256 MB

  163 GB available

  iWorks ' 09 has been upgraded to the latest versions

  No new upgrade is available for the system.

  My Question: Why the fan on my macbook pro continues to run at a fast pace for long periods?

  I guess that the fan runs constantly, because the CPU is working at a high rate. I rebooted several times but without any resolution systems. At the bottom of the computer is very hot at times so place the laptop on an object that allows good air circulation. This problem occurs intermittently every few weeks or more. I wonder if it is downloading an important upgrade, do a scan of viruses, or by working as a bot. Lights for hours. Currently, I estimate that it has worked rapidly to possible 6 hours. Thank you.

  It will usually be to dissipate internal heat from running resource intensive applications.

  Download and install a temperature/speed control application.

  Open the activity monitor all THE PROCESSES and CPU to display values between high and low.

  When the fan speeds up, post pictures of both for review.

  Also run Apple Hardware Test:

  https://support.Apple.com/en-us/HT201257

  Note that an error free AHT is inconclusive.

  Ciao.

• Issue between Cisco and ESX switch

  It is a small deployment with an ESX Server running a Windows Small Business SERVER 2003.

  ESX server has 2 network cards, previously a NIC was connected to a small FastEthernet Switch netgear and all workstations have been working on it.

  I replaced the netgear with a Cisco WS-C2960S-24TS-S and the field still works fine, the problem is that I can't connect to the service console or the VI client from a computer connected to the switch.

  I can't ping the IP switch ESX service console and also can not ping the switch since the service console.

  Switch and ESX console can ping the Windows Virtual Machine and the virtual machine can ping both of them. Therefore, I can get to the VI client via Wirtual Machine (not the best scenario to manage one of its right VMS ESX host?)

  I don't know what the problem is, but it sounds a lot there is a problem with the configuration of port / vlan on the cisco switch.

  Can a Cisco expert help out me here?

  Here are some details of the configuration.

  Port group service Console and the port Vm group do not use no matter what config VLAN on the ESX Server.

  CONFIG NETWORK ESX

  # esxcfg - NICS - l

  Name PCI Driver link speed Duplex MAC address MTU Description

  vmnic0 0b: 00.00 bnx2 up to 1000Mbps Full 00: 1a: 64:b6:06:92 1500 Broadcom Broadcom NetXtreme II BCM5709 1000Base-T Corporation

  vmnic1 0b: 00.01 bnx2 up to 100 Mbit/s Full 00: 1a: 64:b6:06:94 1500 Broadcom Broadcom NetXtreme II BCM5709 1000Base-T Corporation

  vusb0 nickname cdc_ether Up 0Mbps 02: 1a: 64:b6:06:99 half 1500 unknown unknown

  # esxcfg - vswitch - l

  Switch name Num used Ports configured Ports MTU rising ports

  64 6 64 1500 vmnic0 vSwitch0

  Name PortGroup VLAN ID used rising Ports

  PORTS 0 1 vmnic0 VM GROUP

  0 1 vmnic0 Console service

  Switch name Num used Ports configured Ports MTU rising ports

  64 3 64 1500 vmnic1 vSwitch1

  Name PortGroup VLAN ID used rising Ports

  BIG POND ADSL 0 1 vmnic1

  # esxcfg - vswif - l

  Port Group/DVPort IP IP family name address Netmask Broadcast Enabled TYPE

  vswif0 Service Console IPv4 192.168.0.100 255.255.255.0 192.168.0.255 true STATIC

  # ifconfig

  Lo encap:Local Loopback link

  INET addr:127.0.0.1 mask: 255.0.0.0

  RACE of LOOPING 16436 Metric: 1

  Dropped packets: 1310258 RX errors: 0:0 overruns: 0 frame: 0

  Dropped packets: 1310258 TX errors: 0:0 overruns: 0 carrier: 0

  collisions: 0 txqueuelen:0

  RX bytes: 4531037961 (4.2 GiB) TX bytes: 4531037961 (4.2 GiB)

  vmnic0 Link encap HWaddr 00: 1a: 64:B6:06:92

  RUNNING BROADCAST MULTICAST MTU:1500 metric: 1

  Dropped packets: 94579247 RX errors: 0:0 overruns: 0 frame: 0

  Dropped packets: 99834049 TX errors: 0:0 overruns: 0 carrier: 0

  collisions: 0 txqueuelen:1000

  RX bytes: 127899970453 (119.1 GiB) TX bytes: 19056702095 (17.7 GiB)

  Interruption: 209 memory: 92000000-92012100

  vmnic1 Link encap HWaddr 00: 1a: 64:B6:06:94

  RUNNING BROADCAST MULTICAST MTU:1500 metric: 1

  Dropped packets: 3585973 RX errors: 0:0 overruns: 0 frame: 0

  Dropped packets: 3018690 TX errors: 0:0 overruns: 0 carrier: 0

  collisions: 0 txqueuelen:1000

  RX bytes: 2304776001 (2.1 GiB) TX bytes: 1021855293 (974,5 MiB)

  Interruption: 217 memory: 94000000-94012100

  vswif0 Link encap HWaddr 00:50:56:45:43:6 C

  INET addr:192.168.0.100 Bcast:192.168.0.255 mask: 255.255.255.0

  RUNNING BROADCAST MULTICAST MTU:1500 metric: 1

  Dropped packets: 367248 RX errors: 0:0 overruns: 0 frame: 0

  Dropped packets: 126300 TX errors: 0:0 overruns: 0 carrier: 0

  collisions: 0 txqueuelen:1000

  RX bytes: 33905320 (32.3 MiB) TX bytes: 154760077 (147,5 MiB)

  vusb0 Link encap HWaddr 02: 1a: 64:B6:06:99

  RUNNING BROADCAST MULTICAST MTU:1500 metric: 1

  Fall of RX packets: 341442 errors: 0:0 overruns: 0 frame: 0

  Dropped TX packets: 0 errors: 0:0 overruns: 0 carrier: 0

  collisions: 0 txqueuelen:1000

  RX bytes: 26973918 (25.7 MiB) TX bytes: 0 (0.0 b)

  CISCO SWITCH CONFIGURATION

  Port on which the ESX nic is connected to:

  interface GigabitEthernet0/1

  switchport mode trunk

  switchport nonegotiate

  switchport port-security

  aging of the switchport port security 2

  security violation restrict port switchport

  inactivity of aging switchport port-security type

  macro description cisco-computer desk

  spanning tree portfast

  spanning tree enable bpduguard

  !

  ******************************************

  CONFIGURATION OF VLAN

  !

  interface Vlan1

  IP 192.168.0.253 255.255.255.0

  !

  interface Vlan2

  Description management Vlan

  no ip address

  !

  interface Vlan10

  Test description Vlan

  IP 192.168.121.253 255.255.255.0

  !

  Default IP gateway 192.168.0.1

  Any help would be appreciated.

  Thank you

  I think I've seen this before. I'm not super familiar with this switch, but I think that the problem is with cisco-computer office macro.

  Try using the macro switch cisco instead since you are addressing a vSwitch on the other end. You can always check the mac address table and see if your Mac to the vswif (service console) make their appearance. If they are not then appear this is an inconsistency in the port between the Cisco Switch and vSwitch.

  Louis

• Equium L10-273 kept switching between battery and power

  Hello

  I saw a similar post here and I was wondering if anyone could tell me if they have had this problem sorted? My Equium L10-273 kept switching between battery and power all others second, which made it impossible to type, it's got worse and worse. I thought it was a problem with the power supply, but when I removed the battery from the laptop is ok running of the adapter.

  He kept also make a noise of hissing/crackling growing fan region, which stopped when I removed the AC adapter. The adapter was unusually hot, and the fan area became too hot to the touch. This stopped now, I removed the battery, so I want to know is what someone has solved this problem by replacing the battery or it should be returned?

  This laptop is less than 2 years old, but apart from his one year warranty.

  Hello

  According to the description of your problem, I think there is a problem of electronic power supply. Sorry but there is not a universal solution, and I recommend you contact the service authorized in your country. Explain the situation and see what they say.

• The event viewer displays continuously errors with ID 7000 and 7009

  I use Acronis Disk Monitor, which shows the disk health 82% due to a bad block on disk. Observer events poster continually errors on ID 7000 and 7009, but I can't find a solution to these errors or what they mean exactly.

  11/14/2010 08:31 am, Catkin333 wrote:

  I use Acronis Disk Monitor, which shows 82% because of the bad health disk
  block on the disk. Event Viewer displays continuously errors on ID 7000 and
  7009, but I can't find a solution to these errors or that they
  mean exactly.

  If Acronis reports bad blocks on the disk, then you should replace the disk as soon as possible.  Blocks of bad sectors/bad is not repairable, and once they begin to appear that they tend to behave like a snowball rolling downhill, you will get several of them with increasing speed.  You may lose your data if you keep using this drive.

  Regarding the events 7009 & 7000, you will need to copy & paste the events here for give us to you more information.  Double-click on the event to see its properties, and then click the icon of the Clipboard (which looks like 2 pages of paper) to copy the event, you can then paste it in your next post.  These Service Controller errors may be caused by a multitude of different things.

  John

• Unable to disable UAC errors: to continue, type an administrator password, and then click Yes, but he is nowhere to type a password and Yes is disabled.

  Original title: to continue, type an administrator password, and then click Yes, but he is nowhere to type a password and Yes is disabled.

  Yesterday I just reinstalled Windows 8, replacing the preview of the version and the official version.

  I would like to disable UAC and various other things, but I can't.
  Do you want the following program to make changes to this computer?
  Control parameters of account user (or almost anything from the control panel)
  To continue to type the administrator password, and then click Yes.
  There is no area password to type in. He 'bumps' when I type. I can only click on the No button or display unnecessary details.
  I will not restore the system on a new installation. Apparently, it's an old bug that has never been fixed because you can just tell people to do a system restore and close the book on the complaint. If please post a proper fix and stop wasting users time.
  Hi, I know I'm a little late to the party, but I found this post faced a similar problem and thought that post my findings.
  I found a work around for this problem, which does not require a reinstall of Windows, but you may lose your user account.
  Summary:
  The problem is that in Windows 8, the administrator is inactive by default, you will have to find a way to activate it. You can enable the admin account as an administrator,.
  However. Fortunately, (on my machine anyway) it seems that you can access your hidden from the Safemode administrator account. If your first set of objectives will be as follows:
  -starting in safe mode
  -Log in as an administrator
  -l' administrator, enable the account administrator similarly.
  -Restart your machine and you as an administrator outside of safe mode (normal mode).
  From here, you should be free to do what you want. Now that the admin account is active, you are allowed to type a password when prompted (by default that the password is empty). For me, however, when I tried to promote my previous user administrator account (among other things) I noticed symptoms that seem to indicate that the account ceased to exist. I went through measures to set up a new account and get it synced with my microsoft email account.
  -Create a new user account
  -give administrator rights
  -remove my old (for some reason, hidden) account
  -Sync to the top of my new user account with microsoft e-mail account.
  Directions for use:
  How to get admin access:
  (1.) start in safe mode. You can make it easier by opening a command prompt (Start menu-> type "cmd"). And type "shutdown/r/o".
  2.), your computer begins to restart, but give you a set of troubleshooting options. Choose troubleshooting->-> start of the Advanced Options settings.
  3.) after reboot and enter safe mode, users of contactor by going to the start menu-> click on your user name-> and choose administrator.
  4.) Windows will begin the first initialization for this account.
  5.) once connected, open the command prompt, this time as a Director. (Make a right click-> Run as administrator).
  6.) type "net user administrator / Active: Yes" to set the admin account as 'active'. It will now be shown outside of safe mode.
  7.) restart your computer and log in as administrator again. You can now add users and to play with the permissions etc. (metro options are not available in safe mode, where the reset).
  How to remove your old account of 'lost' and synchronize your new account with the microsoft account.
  1.) create a new account via the control panel users. Don't forget to give you administrator rights.
  (2.) to remove your lost old account by typing "net use /del" in an administrator command prompt. You need to know your old account name, good luck with this one.
  3.) go into the settings of your pc: open the context menu on the right-> settings-> "change PC settings."
  (4.) to go to the users-> Select 'switch to a Microsoft account» tab
  I hope this helps!

• Today, we are locked into sitting and staring at the stupid hourglass or spinning cirlces infinite so that your OS continues to steal the memory and performance

  I just want you know I hate using this operating system. WIN 7 and WIN 8 on different computers. Years ago the opportunity to correct a bit your * but today we are locked in to sit and watch the fool or spinning cirlces infinite hourglass while your OS continues to steal the memory and performance of any type of material that is using your operating system. I can't wait to own a computer that runs an operating system that doesn't degrade not just because I use it for work and play. There is a special place in * for windows programmers and engineers.

  Original title: why windows suck so bad!

  Hello

  These should help:

  Ways to improve the performance of your PC
  http://Windows.Microsoft.com/en-us/Windows-8/improve-PC-performance

  Maintenance & performance
  http://Windows.Microsoft.com/en-us/Windows/performance-maintenance-help#performance-maintenance-help=Windows-8&V2H=win7tab1&V3H=winvistatab1

  Crashes Windows or freezes
  http://support.Microsoft.com/kb/2681286

  How to speed up your PC
  http://support.Microsoft.com/kb/2746761/en-us

  =======================================================

  You use a 3rd party antivirus/antispyware/security program? If so many people
  can cause slow start from the bottom.

  Check with the support of the system Maker (manufacturer of motherboard for customized systems), their
  online resources and the drivers and ask questions in the forums about known problems.
  Updating the BIOS , drivers of low level chipset and embedded and separate major
  device drivers (anyone who can have an impact on the speed of startup and performance).

  Note the use of Win Key + X and Win Key + W (to go on the Control Panel, Run and parameters
  According to needs). Win + D key calls the office and using Win Key active / disable the office and
  Splash screen.

  Check startup programs.

  Right-click in the left lower corner - Manager of tasks
  Or Windows key + X - Manager of tasks
  Or right click on the taskbar - task manager

  Check the Startup tab.

  More troubleshooting:

  How to perform a clean boot for a problem in Windows Vista, Windows 7,
  or Windows 8
  http://support.Microsoft.com/kb/929135

  Other programs to help:

  Autoruns - free - see what programs are configured to start automatically
  When your system boots and you connect. Autoruns also shows you the complete list
  Registry and file locations where applications can configure auto-démarrer parameters.
  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx
  Process Explorer - free - find out what files, registry keys, and other objects
  processes have open, which DLLs they have loaded and more. This unique
  powerful utility will show you even owned by each process.
  http://TechNet.Microsoft.com/en-us/Sysinternals/bb896653.aspx

  =======================================================

  If necessary:

  Try to do a "Refresh your PC without affecting your files" (or modification of your personal data
  settings) or even a restore. Be prepared to re - install the programs, applications will remain.
  And having redundant backups of your files on the disk main hard is always a
  good idea.

  Windows 8 includes special discount methods (keep files and settings) or a reset
  (new installation remove all).

  How to restore, refresh or reset your PC
  http://Windows.Microsoft.com/en-us/Windows-8/restore-refresh-reset-PC

  How to create a system image to refresh your PC in Windows 8
  http://support.Microsoft.com/kb/2748351

  How to update Windows 8
  http://www.eightforums.com/tutorials/2293-refresh-Windows-8-a.html

  How to reset Windows 8
  http://www.eightforums.com/tutorials/2302-reset-Windows-8-a.html

  If you need a repair disc:

  Create a system repair disc
  http://Windows.Microsoft.com/en-us/Windows7/create-a-system-repair-disc

  How to create a "system repair disc" (CD/DVD) in Windows 8
  http://www.eightforums.com/tutorials/2855-system-repair-disc-create-Windows-8-a.html

  How to create a recovery USB in Windows 8
  http://www.eightforums.com/tutorials/5132-recovery-drive-create-USB-flash-drive-Windows-8-a.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• I am user of Lightroom 5. Consider purchase version 6. Not happy with the subscription option, bcs, it looks like a year of use I will not be able to continue to use this version and you want me to pay more to continue to use LightRoom 6. Is this good? If

  I am user of Lightroom 5. Consider purchase version 6. Not happy with the subscription option, bcs, it looks like a year of use I will not be able to continue to use this version and you want me to pay more to continue to use LightRoom 6. Is this good? If so - I'll stay with Lightroom 5.

  You have two options to switch to Lightroom 6:

  1. Subscribe (including Photoshop CC 2014), or
  2. Buy the traditional way CS6 upgrade:

  Products

  Click buy

  I want to buy: menu, choose Update (instead of the default is Full)

  I own: Photoshop Lightroom 5.x

  Make your purchase.

• Firefox does not switch not between tabs if clicked 33.1.1 worm?

  Since I've upgraded to 33.1.1 I can't switch between tabs and now I have a tab ghost between the current tab and the sign + to open a new tab. Even if I open the new tab, I can't switch to him.

  Help!

  Update: remove the Restorer of the classic theme add-on seems to have been the culprit. Hope that helps someone else running this problem.

• Is it possible to switch languages between paragraphs in 5 Pages?

  I just upgraded to a new Macbook running the Mavericks and using iWork with 5 Pages. I am writing a thesis that is to regularly switch between English and French. On my old Mac running an archaic version of the word for Mac, I was able to switch between languages by going in "Language."... "and then setting the language for the individual paragraphs. I was even able to create body styles in the document template for each language, so that I can switch between languages quickly, just keyboard shortcuts.

  On Pages you seem to not even be able to change the language for the individual paragraphs at all? As far as I know, you can only change the language for the entire document using the grammar and spelling... Display spelling and grammar-> language - or not at all. The only way I seem to be able to get around this is simply by disabling all spelling and grammar correction settings, so that at least I can type in French without finding it's autocorrected it all back to English.

  This thread - pages 5 change the languages of the various paragraphs? suggests that the feature has existed in the last Pages, but is now auto - however, based on my own experience, it certainly isn't!

  Is there a work around for this maybe using Styles? Otherwise, it will be without a doubt the thing that sends me to Microsoft Word...

  Thank you

  ktamb wrote:

  the feature existed in the last Pages, but is now automatic

  5 pages has been removed and the ability to text of language tag.  For this and other similar reasons, many users have slept with or is returned to 4 Pages, which is superior in several ways, or moved to Word or LibreOffice since 5 Pages was released 3 years ago.   I recommend do you the same thing.

• Display satellite C50-A546 cards how to switch between NVIDIA and INTEL?

  Hello

  How can I switch between NVIDIA and INTEL graphics cards?

  PS
  I have already installed all the drivers, but I can see that INTEL the card used chart!

  * OS: Windows 8.1 x 64
  * NVIDIA driver: 340, 52-portable
  * DirectX: 11

  Hello

  The Intel graphics chip, which is part of the central unit should be used for low performance applications, because it allows you to save energy and reduce the internal temperature.

  For best performance while game, it s advisable to use the external GPU (nVidia or AMD)
  This setting can be changed in the nVidia control panel s

  Here, you should choose manage them 3D settings (can be found on the left in the nVidia control panel)

  Now in the main window, you will find two global settings and program parameters tabs
  In the program settings tab, select the (game) program that needs to use the nVIdia GPU

  If it is not listed, click the Add button
  Then choose the graphic processor preferred for this program (generally must be nVidia processor high performance)

  Last but no less, in this program-specific settings, you can assign additional features to improve performance.