Faster CPU for a T400?

Similar Questions

• faster CPU for dc7600

  Hi-

  Want to update my motherboard with faster cpu, I searched on intel and this site and there are so many chips... does anyone have an answer would like to go with the intel 950 but not sure on that. I thought I saw a similar question and answer here but cannot find. Motherboard is PN 381028-001

  Thank you

  Hello:

  The fastest CPU you can install it in the DC 7600 is the Pentium D 945 or 950.

  They are both the same speed, but the 950 a VT (virtualization technology). They also cost more.

  I went with the cheapest sSpec SL9QQ 945.  If you have need of VT, continue with the 950.

  See this post below and you'll have all the info you should update. You will need to have the latest version of the BIOS and the firmware installed.

  http://h30434.www3.HP.com/T5/desktop-hardware/dc7600-CPU-upgrade/TD-p/578827

  Paul

• Faster CPU for Satellite A200-1AB

  Hello

  No one knows what would be the fastest possible processor I could put in an A200-1AB or where I might be able to find the information.

  It comes with a c2d T5300 which is 1.7 ghz/533bus... I hope that it can take 667bus chips speed but for the life of me can not find information on the mother or this card that it accepts.

  Any info appreciated :)

  Tom

  Sorry, but I don't really understand you. You buy laptop latest, and after a few days you think CPU upgrade. For me, it's very strange. Why?

  Usually before purchasing laptop or laptop even, it is useful to take some info on the hardware. You know very well what you want to do with your laptop and it is logical that you should buy the right equipment for your needs.

  I will say that there are many models A200 with much better equipment and performance graphs than yours. Why you didn t pay 300 Euros more for best laptop?

  Just to be clear: the CPU upgrade is not taken in charge and everything you do is at your own risk. If you open the notebook the warranty will be cancelled definitively. If you need more performance upgrade of RAM to the maximum level. It will be much cheaper and without any risk.

  Sorry because I didn t give you info on compatible CPU, but I just wanted to write my comment on upgrade CPU on the new laptops.

• Faster CPU for TS200?

  Hello

  I think about upgrading the processor in my TS200.

  What is the fastest processor that will work in it? All LGA1156 CPUs should work?

  Thank you very much

  T

  the fastest processor supported in the TS200 is a 2.93 GHz Xeon X 3470.

  http://www-307.IBM.com/PC/support/site.WSS/MIGR-75521.html

• Why the fan on my macbook pro continue to run at a fast pace for long periods?

  The MacBook Pro mid-2010

  OS X El Capitan, 10.11.3 version

  Processor: 2.4 GHz Intel Core 2 duo

  Memory: 4 GB 1067 MHz DDR3

  Graphics card: NVIDIA GeForce 320 M 256 MB

  163 GB available

  iWorks ' 09 has been upgraded to the latest versions

  No new upgrade is available for the system.

  My Question: Why the fan on my macbook pro continues to run at a fast pace for long periods?

  I guess that the fan runs constantly, because the CPU is working at a high rate. I rebooted several times but without any resolution systems. At the bottom of the computer is very hot at times so place the laptop on an object that allows good air circulation. This problem occurs intermittently every few weeks or more. I wonder if it is downloading an important upgrade, do a scan of viruses, or by working as a bot. Lights for hours. Currently, I estimate that it has worked rapidly to possible 6 hours. Thank you.

  It will usually be to dissipate internal heat from running resource intensive applications.

  Download and install a temperature/speed control application.

  Open the activity monitor all THE PROCESSES and CPU to display values between high and low.

  When the fan speeds up, post pictures of both for review.

  Also run Apple Hardware Test:

  https://support.Apple.com/en-us/HT201257

  Note that an error free AHT is inconclusive.

  Ciao.

• Need a fast computer for PTC software.

  Hi all.
  I need a fast computer for PTC software, OS isn't a problem is long is he'll run PTC with add on no hick-ups.
  System will be used for the calculation and drafting/design.
  This is a not a gaming computer...
  Thought was a motherboard with a front Quad, but I was told that this will not work:(parce que la limitation de la cpu et cela mettrai mon bureau sur un territoire de serveur.)
  My question what OS what is the best OS for several CPUS and multiple core CPU for the desktop?  Can some one give me the breakdown of that OS supports the amount of CPU and what OS supports the amount of carrots? Which is more economical two quad CPU or separate before the processor on the motherboard.
  Thank you.

  Think catch.  The chip in the socket is called a physical processor.

  Vista Home Basic and Premium can use a.  Any number of cores is OK.  Carrots

  are called logical processors.

  Vista Business, Enterprise and Ultimate can use two jacks.  Number any of

  cores of each is OK.

  Only the editions of Windows Server can use 4 processors and up to.

  See you soon.

  Mick Murphy - Microsoft partner

• a faster way for PDM-to-Excel conversion?

  I connect my packets received using blocks PDM, since it is suggested that IO low is the fastest. Since I need data in formal Excel, after my experience, I run a small code that uses 'Reading file of measure' and 'Write in the file of the measure' blocks to convert TDMS to Excel.

  This conversion takes too long, for example 15 minutes from port of 1 million bits of PDM for Excel (I connect packets in their binary form, of 1 and 0). I have attached the VI conversion.

  I have 2 questions:

  1. does anyone know any faster way for the conversion of PDM in Excel?

  2. I need the block 'Reading files measure' in my conversion code since the packets received are saved in TDMS in the form of a single vector, and I need to convert this very long vector in a matrix where each line corresponds to a received packet. Is it possible to make connecting TDMS in the form of a matrix, instead of one vector? This can be slow down my code much.

  Thank you!

  Hi filipfilip,

  Have you considered using the TDM Excel add-in? You can then save the resulting Excel workbook and get the desired file format.

  More information can be found here:

  http://www.NI.com/white-paper/4906/en/

  There is a solution on this post on the forum too which can allow you to do this automatically. I don't know how much faster it would be than your current method but I think it would be interesting to give it a go.

  http://forums.NI.com/T5/LabVIEW/convert-import-TDMS-to-Excel/m-p/1088746

  I hope this helps, please let me know if you have any questions.

  Thank you

  Charlotte N.

• Upgrading CPU for HP Pavilion P7 1534

  Hi, I'm looking to upgrade my CPU for my pavilion p7 1534. The motherboard has a socket FM2 and comes with A8-5500. Maybe upgrade the CPU to an A10 - 6800 k the best upgrade AMD or the A10 - 5700 k. I wonder because the 5700 k is a Trinity, while the A10 is a Richland.

  Nate, welcome to the forum.

  Here are the processors supported by HP and the motherboard:

  • Socket type: FM2

• driver realtek RT8139/810 x Fast ethernet for HP CQ58-d57SR adapter

  Take the new HP compaq CQ58-d57SR. Search help driver realtek RT8139/810 x Fast ethernet for Win7 32 adapter?

  After installation position rezult pilot will be negativ. Run Auto search on internet, win7 see adapter ok

• Use of trend CPU for a service

  Hey everybody,

  Hoping you can help.  I would lke to display graphically, use of CPUS to a virtual machine or VMs contained within a service over a period of 6 months. I want also to average usage to demonstrate that usage has increased or decreased during this period of recovery.

  Easy enough to do the first part, but you know how I could also show the average use over this period?  The overlay only as 'average', I can think of will show an average apartment during the entire period.  I really want to show if the average was up or down.

  See you soon

  It is a matter of good use for a derived measure.

  A derived measure is calculated according to one or more other measures.

  In this case, you can define a time - or schedule-driven derived metric whose scope corresponds to a Service.

  The calculation for average usage of the CPU for all guests of the service could look like:

  AVG (#utilization of $scope.hosts.cpus for 30 minutes #)

  Once you have created this metric, you will be able to track this value over time and it monitor changes.

  There is an example of how create a metric derived in How to create a Derived metric (to count the VMS under tension).

  Kind regards

  Brian Wheeldon

• Wonder average CPU for virtual machines

  I have a supermetric that gives me the average demand of CPU for virtual machines.

  It works as set below:

  avgN($R40:A2055,3) / avg($R40:A2030)

  R40 is the data center - A2055 is the attribute of MHz CPU demand.

  A2030 is powered on virtual machines in the data center.

  Is it possible for me to write this formula without having to divide it by the total number of virtual machines in the data center?

  Is 'average' looks should do.

  

  Fix.

• How to interpret the Montior CPU for the merger activity data?

  I had an interesting thing happen today:

  • I noticed that my Macbook Pro was a very high coverage of time CPU.

  • I checked the activity monitor to see what might happen - Firefox (as usual) was consuming more processor said cycles (30-50) - Fusion was well down the list (nevers merger seems to signal something more than 2-3).

  • I spent a lot of time trying to understand what could be the problem - juggling makes Firefox only a modest improvement.

  • Finally noticed that suspend the virtual machine (that worked only 1 app in XP) caused the CPU usage (as shown on the /graph/ in the activity monitor, not as shown in the numerical value of the VMWare Fusion line) to fall and the time quickly dropped by 20 + C.

  • Restared the VM - time go way up, but VMWare Fusion still report it is not using any CPU tasks stored in the virtual machine, and it was VMWareUser.exe (this, as I understand it, is a well known problem with drag-and-drop in a virtual machine), consuming 99% of the "VM - processor" I killed this process, the cpu of the VM goes to 99% idle and the falling time cpu for the ranges of normal temperatures.

  So - my question is why the line in the report of Activity Monitor such a small numerical value for the processor utilization associated with VMWare Fusion when (at least in this example) it seems that the CPU was being seriously imposed by the leak inside the virtual machine process? How should I interpret it?

  Thank you

  Doug

  As noted in the frequently asked Questions on VMware Fusion, Fusion uses a frontend/backend architecture. The merge process that appears in the default settings of the activity monitor is the user interface process, which manages receives them, drawing on the screen and so on. Work heavy is done by a process vmware-vmx belonging to root (one per VM) - view all processes to see / them.

  With respect to the use of the CPU, see frequently asked Questions about VMware Fusion: high CPU utilization.

• doc2text process using 100% cpu for a long

  I have encountered this problem before and never received a satisfactory solution.
  
  When we publish some PDF documents via collab in KD, doc2text process on our servers portals (also our API) turn at 100% of the CPU for about 90 seconds. This causes the publication of collab to fail, so we resort to directly download the file to the KD via downloading content.
  
  (1) why doc2text works on our servers of portal in the first place? Is this a result of the service portal server or api? If I move the API service off the coast to another machine, which will remove that pig of our front end servers CPU?
  
  (2) has anyone seen this before, or found a way around it? Y at - it a newer version of doc2text in gR 10, 3 that is not so terrible?
  
  I'm about to move to 1 - cpu virtual in our new environment, so any process that takes up 100% of the CPU will kill performance.

  Joel,

  Collab makes an IDK call to publish the document, so it does not hit the API service. For this reason, I propose the wide API service to another server so that the portal is not affected.

  HTH,
  -Verhee

• G61 - 320CA: upgrade CPU for laptop PC HP G61 - 320CA

  Hello.

  I bought this laptop in 2005 (new)

  Product name: HP G61 - 320CA (laptop, laptop)

  Product number: VM345UA #ABC

  Microprocessor: of GHz AMD Athlon II Dual-Core processor for notebook PC M300 2.00

  Cache of the microprocessor;         1 MB L2 Cache

  Motherboard:, DAOOP8MB6DO REV: D (cannot distinguish if they are zeros or letters after DA and P8MB)

  also written near the edge 16 "OP8

  After a good cleaning, I realized that I have the opportunity to upgrade the processor. The processor is removable.

  The installed processor is an AMD Athlon II

  Is there by chance, a way to find an upgrade to this processor that would be compatible with the laptop?

  Technical support told me that Intel were not capatible to stick with AMD but it coulndn can't tell me which one I could install.

  This laptop is no longer under warranty, but it is in perfect condition. I would like to find a faster processor compatible.

  Even if abandoned, I know I can find an upgrade on eBay (as any one of my office PCs.)

  Thx a lot

  Here is the Manual:

  Manual

  Top of page compatible processor:

  M600 AMD Turion™ X 2 Ultra Dual-Core Mobile Processor:, Processor 2. 4 GHz, 2 MB L2 cache, 3.6 GT/s HyperTransport speed

  http://www.eBay.com/ITM/tested-TMM600DB023GQ-AMD-Turion-II-Ultra-M600-2-4GHz-socket-S1-CPU-procesor-/191892890482?hash=item2cadb52372:g:JC0AAOSwtJZXWho-

  They are practically giving these AMD processors because there is simply no demand away. It might be a fun project and if you have already opened it upwards and I saw how to remove and replace the processor at this price, you might as well. There will be an improvement, but don't expect miracles. Let us know if you need help most.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• Upgrading CPU for HP Pavilion dv9730nr notebook Entertainment

  I'm looking for the best/most fast Intel processor to upgrade a HP Pavilion dv9730 Entertainment notebook. The motherboard is a Quanta 30CB. Aware of the processor is an Intel Core 2 Duo T5450 1.66 GHz. I am trying to upgrade this laptop for my grandson to play some of the new games of intense action. I looked at different forums, but most of them is at least two years. I also watched the service for laptops manual series dv9700. The top page in their list processor is the Intel Core 2 Duo T7700 2.4 GHz. Since most of these lists are old, I want to know if there are faster processors that are compatible with the laptop and a motherboard safely.

  Only, you are sure to install a processor originally proposed by HP on this range of laptops. As noted above, it is not really a mother Quanta is a motherboard HP, full owner. There is also no way to improve the system without radical changes in case of cooling and engineering tips; the only CPU cooler is the original factory unit unless you do another and even in this case, the tight fit limits what you can really do. The fsb and the power must remain the same, as well.