FC Port-Channel does not

Similar Questions

• Why do write can not be performed because the number of data channels does not match number of channels in the task.

  Possible reasons:

  Scripture cannot be performed because the number of data channels does not match number of channels in the task.

  When writing, provide data for all channels in the task. You can also change the task so that it contains the same number of channels as the written data.

  Number of job channels: 8
  Number of data channels: 1

  Lama says:

  The DAQmx vi writing gives me the error. If I run a single channel, isn't a problem. Multichannel gives me error.

  You are funny! Why tie yourself to work VI (single channel) instead of one that gives you errors (multichannel)?

  (If your car does not work, you bring car your wives to the mechanic, right!)

  What is the exact text in the multichannel 'physical channels' when you do the AO control?

  Lama says:

  I did a sequence to ensure that each function has been run in the correct order. Wouldn't a race condition.

  All you have to do is wire the 'start of task' error at the entrance of error of the DAQ assistant and then back to 'stop task' and things will run in order. Guaranteed! Think the stream! Everything else can run in parallel or the order is irrelevant.

  First convert the sequence stacked to a sequence of plate, remove the flat sequence and add the mentioned son. Now, do a "cleaning pattern.

  A when stacked with the inhabitants of the sequence is one of the worst construction you can possibly do. It makes the code difficult to follow, impossible to maintain, difficult to debug.

• the R channel does not record on ION U RECORD.

  the R channel does not record on ION U RECORD.

  original title: ION U RECORD.

  Hi Patrice,

  Please select your language from the drop-down menu above to post your question in the language of your choice. The forum in which you've posted is for English only. If you can't find your language above, support for additional international sites options are by following the link below:

  http://support.Microsoft.com/common/international.aspx

  Thank you

• Port forwarding does not work on EA6900

  Please help me to know what is the reason for this port forwarding does not work on my Linksys router:

  Model: EA6900 v1.1
  Firmware version: 1.1.42.161129

  I've set up two ports: TCP 22 and 8070 TCP to 192.168.1.10. (192.168.1.10 is up and running, I can reach the LAN ports).

  Yesterday, I had a live chat with Linksys support we tried to re - download the firmware even, but that did not help. Then factory reset and reconfigure the router did not help either.

  Unchecking "Filter anonymous Internet requests" and disable uPNP didn't help either (they have been suggested in similar topics).

  However, the IP displayed tab troubleshooting/Diagnostics reflect my external IP address (the IP displayed by http://whatismyip.com), which is weird, because I never have IP from my ISP from 100, that is displayed on the Diagnostics tab. So I guess it's a fake display or it relates to access to my router via www.linksyssamrtwifi.com ?

  Anyway I tried the two IPs from the outside, but the transfer simply doesn't work. (It works fine when I use my old router TP-Link).

  Please advise!

  Sorry guys, it seems indeed a double NAT problem. My ISP can detected MAC address change when I started using EA6900 (thinking that I couldn't not need public IP?) and since then he sends me IPs for NAT - ed. It is strange that the same day, he was working with my old router, but now it is even not working with my old router and not even working when I connect directly to my windows PC to my ISP (via PPPoE). I called their support line and they said that they will solve this problem within 72 hours. In any case, thanks for your help!

• Port 139 does not not on Windows 7 after deployment.

  Hello

  I created some images of new installations of Windows 7. But the pack of GPO that is applied in MDT 2012 changes settings in windows 7 so that port 139 does not correctly work with gap analysis network SMB.
  recently we bought workstations that already have a Windows 7 image on them. But because computers OS was deployed hollow some imaging modalities 139 port does not work properly. Is there such a tool from Microsoft to restore the port 139 on a charge CD Windows 7 feature?
  Or any Microsoft employee who has done any research into this problem and tested and found a solution to this problem?
  Thank you.

  You can take this on the Technet forums because I don't know where the sizes are fixed. One thing to remember when the GPO is that in many cases, changes may "tattoo" the registry and must be explicitly changed back instead of be reset to the default value.

  http://social.technet.Microsoft.com/forums/en-us/category/w7itpro

  I hope this helps.

• When I plug my portable hard drive to the usb port it does not read and display the contents...

  When I plug my portable hard drive to the usb port it does not read and display the contents...

  Hi deaza,.

  Ø Have you connected the USB hard drive to the computer directly or you have used an external USB hub to connect?

  O trying to connect to another USB port to check if it works?

  O the hardrive shows in windows of the computer when you connect it?

  Method 1:
  If you have installed security software, I suggest you to temporarily disable the security software and connect the USB and check to see if the same problem happens. Make sure that you enable the security software after checking.

  Alternatively, you can try to plug the USB key into a different USB port and check if it helps.

  Method 2:
  I suggest trying to launch hardware and troubleshooting of devices and check to see if it helps, here is the link:http://windows.microsoft.com/en-US/windows7/What-to-do-when-a-device-isn ' t-installed-correctly

  Method 3:
  If this does not help, then follow these steps:

  (a) remove all your USB devices. Use the safely remove the feature to turn them off.

  (b) open Device Manager and navigate to the section for USB. Uninstall all USB drives. There should be one for each USB port, and then restart.

  To open Device Manager, go to the link below and follow the steps:

  http://Windows.Microsoft.com/en-us/Windows7/open-Device-Manager

  (c) Windows should re - find all of the devices. If it is not the case, note the error message and let us know.

  You can also navigate to the link below and follow the steps to install the USB device.

  http://Windows.Microsoft.com/en-us/Windows7/install-a-USB-device

  I hope this helps. Let us know the results.

  Thank you and best regards,

  Srinivas R

  Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Standard vSwitch_Custom VM (Vlan200_VM network) port group does not.

  Hi guys...

  Scnerio:

  ESXi 5.0

  VCenter 5.0

  2 connected local network cards to vswitich 0 Active\Active configuration.

  The virtual computer name: FSAPP_1

  Note: good VLANS are created externally NETWORK

  I created another group of ports VM network VLAN 200_VMnetwork.

  I have attached TWO maps LAN to VM. A LAN card is connected to the port default VM network group and another is connected to network VLAN200_VM.

  A LAN card is connected to the local network (Private IP) and another is connected to the Wan (public IP)... IF I CONNECT the TWO VMNIC "DEFAULT virtual machine network" I am able to ping both subnets.

  
  

  But any vNIC which is connected to the VLAN200_VM network is NOT working...

  
  

  
  

  Please see the attached snapsshots...

  Thank you

  I did not ask you to do what I asked you to test is the separate two VM on the host even be configured to use the VLAN 200 portgroup and verify that these two people are able to talk to each other.

  Once you've found that the books above. Go back to your network team and make the request to configure the switch in the trunk output ports (which does not remove the tag VLAN on the package on the output of the switch) as opposed to be defined as access (that strips the tag VLAN).

  It is my firm belief that the port group does not work because your switch is misconfigured based on my above statement.

• RGB channel does not show the imported images...

  RGB channel does not show the images imported... I can see it in blue, red and green circuit, but not in RGB... Please help...

  (I use Photoshop CS6)

  Well, that clarifies.

  Open Photoshop > edit > Preferences > Performance > the GPU settings > advanced settings > Drawing Mode > change to base - from now on, it is in "Advanced". See if that helps.

  If so, your video card doesn't support acceleration entirely for CS6.

  Looks like the driver of your video card is old about 3 years and more than 4 main versions:

  Driver date: 20090208190620.000000 - 000

  Driver version: 7.01.01.849

  Visit the AMD Web site to search for the latest drivers.

  The current version is 12.6, released July 23, 2012. This will certainly help you with your question.

  Also, go to help > update and download / install all the updates that are available for Photoshop. The current version is 13.0.1. You run 13.0 which is a compilation of March 2012.

  Let us know how it goes.

  -ST

• New for iPhone charging Port 6 does not

  Recently, I had the charging port on my iPhone replaced 6, because the original had stopped working properly. With the original, I had to shake the charger autour so he could load, but it was so bad that I could only load if I it held in place. I went to a store local tech to g

  With the new port, I am able to load it with a standard charger Apple iPhone or iPad. However, it does not charge to something else - in the car, with a cell phone charger, when it is connected to my Mac - nothing. When it is connected to these other devices, the phone doesn't even it is plugged.

  Thoughts?

  Means, "went to a store local tech to fix.

  Looking for advice!

• Pavilion 23-b320: Port SD does not

  When I insert one of my SD cards in the SD port, the computer does not meet the presence of the SD card.  When I open file Explorer, the SD card does not appear.

  All USB ports work.

  How to solve this problem.

  Note: this computer is my wife, and he sat on his desk for 2 years unused.  We got married recently and am now trying to get to the top and running.  I have done all the necessary updates for all programs.

  I don't have a recovery disk.

  Interesting...

  See if this driver works instead.

  The W8 driver for your model page shows it has a Realtek card reader.

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?swItemId=ob_155234_1

• Writing to the nodes property DAQmx channel does not refresh the channel values

  Hi all

  I have a riddle.  I created a task programmatically in LabVIEW and programmatically added several analog input channels to the task.  It's easy.

  I wish that my user must be able to modify the individual channels within the task.  To this end, I created a set of screws that allow it to change the settings appropriate to the channel (for example, if it is a channel of thermocouple, it can change the type of thermocouple, CRC value, etc... If it is a strain gauge channel, it can change the coefficient of fish and so on).  These screws all works beautifully, like the VI where they live.

  The specific question that I have is that writing to the channel property nodes refreshes not communication channels.  See the images below.  The first image is the code that needs to define new channels of communication:

  

  Note that immediately after setting the property nodes, I read their values back, just to see what comes out back.

  The second image is an image of the public Service immediately after the execution of this VI.  Note that the values read from the channel property nodes did not updated to match to the set of values, but instead kept their initial configuration values:

  

  What I am doing wrong?  I fought this for a few days now and I'm stumped.

  Thanks for your time!

  Diane

  Hi, Diane.  A week ago, I also had a problem changing the channel properties (not sure that our situtions are exactly comparable, but...).  My 'solution' to want to change the appearance of the task was to just throw the original task and recreate all the elements of the task from scratch.

  I've not done enough 'experiments' to work when you can and cannot change, but am now much more cautious...

  Bob Schor

• N2048 port security does not

  Hi Experts,

  Only, we have deployed a new site that uses the Dell N2048 switches in a stack.

  Now we would add port security to the switch, Port-MAC locking to lockdown one port if another computer.

  According to the manual, to put in place we only need of to the port to locked under the MISTLETOE under switching, network security, port security.

  This does not activate it.

  We tried to add via the command line, in the ports of test, it now shows:

  switchport security of dynamic ports 1

  Still, port security is not enabled. There is another thing that must be enabled in the world to do this job or other commands?

  Thank you

  The output of port security-# show is as follows:

  Port Security Administration Mode: enabled

  It is possible that the tests were not done fast enough. I spent the time-out and ask them to test again.

  Thank you

• PowerConnect 2824 Ports SFP does not

  We bought a new switch 2824 with a corresponding to SFP module replace old 2724 PowerConnect and SFP module.

  After the configuration of the switch and installing it, we were able to get a connection on our uplinked to fiber.
  SFP light illuminates and flashes from time to time, and the switch detects correctly module SFP is inserted and that the fiber is connected.  We can see the insertion of the SFP is detected and the switch for change of fiber mode by looking at the output of the console, and the web administration port status page lists the port as "ComboF" when the SFP is inserted and the fiber is connected.

  However, the switch always indicates that the port State is down.  (The port is not administratively disabled.)

  The old switch works very well with the old SFP module.  The new switch does not work with the old or the new module SFP.  We tried two combo SFP ports.  We also checked that the fiber itself is fine. We cannot get the new switch to display the drop-down list port status that up when you use the SFP. We tried to completely reset the new switch by removing the configuration file via the boot over the serial connection menu and re-run the initial configuration wizard, but the port still won't go up.

  Any ideas?

  After a few tests yesterday, we determined that part of auto-negotiation must be disabled for switch work with our copper and fiber Media converters.

  The 2724 works very well with our media converters, with auto-negotiation enabled.

  The 2824 works very well with auto-negotiation enabled when it is connected to an another SFP transceiver in building switch.

  But when we introduce the Media Converter in the path, the 2824 will bring only the link up if you disable auto-negotiation.

  So far, everything looks good.

• Junction UCS ports worksheet does not, no integration of WWW.

  Hello!

  Key:

  VLAN 200 - all the 20.1.1.0/24

  VLAN 201 - 20.1.2.0

  VLAN 202 - 20.1.3.0

  VLAN 203 - 20.1.4.0

  VLAN 204 - 20.1.5.0

  Just migrated some UCS, HCI SuperMicro and physical servers above 5ks/fex again 9 k column spinal/leafs Cisco ACI running.  Worked well on the 5ks, access ports if necessary, logs allowing VLAN 200 to 204 will stuff UCS and SuperMicro.

  Before I continue, note I am NOT currently any VMM integration, just try to get the same trunk ports to the beach above of VLAN on ports leafs. ***

  Thus, servers physical and other access ports work perfectly.  The links of the trunk of the UCS and SuperMicro don't seem to work right.  By focusing on just the UCS, I can see the entry ARP for the UCS himself, but no resolved IP address.  In addition, I don't see any MAC/IP addresses the Server Blade, or anything else.

  For static bindings EPG, I tried marked (assuming that the law) and not signposted.  ENCAP different VLAN (current vlan-203) but nothing seems to work.  Side of a LLDP and CDP UCS active as I was.

  Speaking of VLAN, I built 5 EPG to do this, each corresponding to a function from one of the 5 VLAN above.  However, the UCS trunk links should allow all VLAN 200-204.  I have a jump on 20.1.2.5 server that cannot call the 20.1.2.x IPs who also live in the UCS, because there are certain types of disconnect to the where the ACPI cannot see in the links of the trunk at all.  I don't know if it's related or fabric EPG associated config.

  I would be very happy to provide additional information, because I'm dead in the water.  Thank you very much.

  Josh

  It depends on if the non - UCS hosts are on the same sheet or not.  You can map an EPG on different ports with some tag and others do not.  There are the limitations when you want to have multiple ports on the same sheet as however no marked.  A single VLAN ID cannot be the tag & unidentified on the same sheet. Even when we put a static as path "unidentified, or 802.1 p ', still need to assign a VLAN unique traffic (can not also be VLAN 201).  It's really a VLAN arbitrariness to the fabric only.  Any evacuation traffic or infiltration of the connected device would send/receive traffic without a tag VLAN.

  Example let's say you have a UCS connected on port 1 and a re-usable on port 2 (same sheet).  You can set EPG - A 'tag vlan 201' for the UCS, and "untagged vlan-205" ports for re-usable connected ports.  Even if the program is different, it does not matter.  The two ports will land in the EPG even at the end of the day and be able to communicate.

  Make sense?

  Robert

  Here's what the config would look like. * Note that my pool VLAN ranges from 200-205, since ACI must allocate a VLAN of the pool especially for unmarked ports (System requirements).  As your hosts are directly connected to the canvas, the VLAN is arbitrary.  We just want that they arise in the EPG even.

  Capture1.jpg

  

  capture2.jpg

  

  capture3.jpg

  

  capture4.jpg

  

• sprite channel does not turn off

  Should be simple; I have a sprie I turn off so it does not play on the stage (works well here), but when I saw in a browser, it is not off. I'm on OSX; MX2004.

  Sprite channels that you turn it off by clicking the button in the
  partition is not saved between sessions. Therefore, if you close Director
  then open it again, this sprite channel likely will be visible again.
  Same goes for the preview in a browser (or publish on projector).
  Start all channels of sprite always visible.

  If you want to force an invisible first channel, you can do
  in a movie script:

  on startMovie
  Sprite (1) .visible = 0
  end

  Who will make channel sprite 1 invisible until you whether visible
  Once again, like this

  Sprite (1) .visible = 1