File system error, cannot be deleted

Hey,.

I had to rebuild a RAID array on a customer Server (in fact I redid it completely). While at it, I upgraded ESXi 4.1 to 5.0 u1. After that, I can't add the RAID array storage. I think a lot, it is the previous file system which is f - ed, but it seems that no matter what I I can not erase completely everything on it. Here are the commands I tried:

vmkfstools - ch. /vmfs/devices/disks/eui.22570001555c70ed vmfs3


It gives me:

Could not check for existing on the device file system "/ vmfs/devices/disks/eui.22570001555c70ed".

Usage: vmkfstools - C [vmfs3 | vmfs5] / vmfs/devices/disks/vml... or,

vmkfstools - C [vmfs3 | vmfs5] / vmfs/devices/disks/naa... or,

vmkfstools - C [vmfs3 | vmfs5] /vmfs/devices/disks/mpx.vmhbaA:T:L:P

Error: Cannot access devices, please check your connection to the device.


fdisk-l /vmfs/devices/disks/eui.22570001555c70ed

Makes me:

***
The fdisk command is deprecated: fdisk does not support GPT partitions.  Thank you for using partedUtil
***

Note: the sector size is 4096 (not 512)

Disk /vmfs/devices/disks/eui.22570001555c70ed: 1999,9 GB, 1999999336448 bytes
255 heads, 63 sectors/track, 30394 cylinders
Units = cylinders of 16065 * 4096 = 65802240 bytes

/Vmfs/devices/disks/EUI.22570001555c70ed disk does not contain a valid partition table

partedUtil mklabel msdos /dev/disks/eui.22570001555c70ed

Makes me:

WARNING: Device /dev/disks/eui.22570001555c70ed has a size of logical sector of 4096.  Not all parts of GNU Parted support at the present time, and the labor code is VERY EXPERIMENTAL.

glibc detected * < unknown >: double free or corruption (! prev): 0x0804f200 *.
glibc detected * < unknown >: malloc(): memory corruption: 0x0804f408 *.

"JJ so of="/vmfs/devices/disks/eui.22570001555c70ed = / dev/zero "bs = 4096 count = 34 = notrunc conv

"JJ so of="/vmfs/devices/disks/eui.22570001555c70ed = / dev/zero "bs = 4096 count = 34 seek = conv 488281054 = notrunc


It seems to work, I get results back, but run the above commands again gives the same results if. Can someone help me with this please?

OK, so I tried to look for other combinations of error messages and others and found some info on that. Seems he is kind of a common problem and it is generally due to two reasons.

(1) the logic unit number is too big (more than 2 TB). However, mine was 1.82 TB.

(2) if there is previous data on the VMWare drives may have problems reading it. I reset (both quick and full), the RAID repeatedly, which is supposed to make the blank disc, but it did not help.

But see the ' Note: sector size is 4096 (not 512) "message made me think. Maybe I chose the size of sector 'wrong' when I recreated the RAID array... I went into the RAID bios and deleted the berries, recreate them again with the sector size 512. In addition, to be absolutely sure, I created two logical drives instead of one; 1 @ 1 TB and 1 @ 820GB.

Booted up and went well add guide to storage again and this time it worked fine.

I remember no adjustment of the sector size to anything other than the default value is 512. And even with a size of 4 KB allocation. So, really, I'm leaning towards the size of the logical disk. Odd how VMWare is supposed to manage up to 2048 GB, but still.

Tags: VMware

Similar Questions

  • BlackBerry Smartphones got a virus on my Bold 9700 Windows, can't delete it, file system error 3

    I used the SD card in my BlackBerry as a way to print some documents. Of course, internet cafes are full of virus of children all this porn downloaded.

    Then, I got a file autorun.inf with all its contents. My problem now is that I can not remove the file from the main virus. Whenever I try to remove it, an error occurs.

    This is the file system error 3, from net.rim.device.api.io.file.FileIOException

    Can I do to remove this thing? I tried the native and Rock File Manager, FileScout Lite file manager, but nothing works

    Raestloz wrote:
    The problem is, it's a Windows virus. Connection to a PC could very well spell trouble. This is the reason why I try to remove the em with my BlackBerry.

    There is no setting in the BB OS change on a file write protection. Therefore, you cannot do it with the BB... If you are not ready to connect it to any PC (maybe even the Internet infected PC coffee it?), then format the card with the BB command is your next step. Maybe you can remove the BB and using a card reader on a PC instead of mass storage Mode?

    Raestloz wrote:

    In any case, can someone tell me what exactly the error means? It seems pretty obvious with FileScout Lite error message, but it would be nice if I can get a confirmation

    The error is indeed explicit... somehow, this received file write protection on it the BB OS recognizes exactly as he said. How it happened? It would be a totally different matter of course... as well, since everyone here is volunteer 'out there', the other user nothing here you receive can be considered as authoritative beyond your level of confidence what information you receive.

    • KB23398 How to remove files from a BlackBerry smartphone

    Good luck!

  • Images of Smartphones blackBerry will not appear on the BB + file system error

    So, I have two problems:

    (1) I went in my 'images' on my Blackberry and there is no picture pictures says * no. *, but when I plugged my BB to my PC and clicked on the pictures folder, I can see all my photos. How is it?

    (2) I can't save a photo on my BB. When I choose 'Save', nothing happens, keeps saying "File system error", sometimes it is said that there is already a file with the same name and when I try to change and choose Save nothing happens.

    Another problem, I just discovered: when I take a picture, I can't delete it later, I get "picture cannot be deleted.

    * I don't have a MicroSD card in my BB.

    Hi and welcome to the Forums!

    Each time a random strange behavior or slow creeps, the first thing to do is a battery pop reboot. With power ON, remove the hood back and remove the battery. Wait a minute, then replace the battery and cover. Power on and wait patiently through the long reboot - about 5 minutes. See if things return to functioning. Like all computing devices, BB suffers from memory leaks and others... with a hard reboot is the best remedy.

    Best!

  • Error message - file system error 1073741502? How can I fix this please?

    I am running Windows 7 Home premium 32-bit on a laptop purchased.

    I used my laptop normally and shut it down last night. This morning, I can not load in Internet Explorer or Microsoft Outlook and when I click on what anyone on the desktop to open it, it does not open. I also notice when you try to shut the computer down that it will not close unless I press the power button. It does not restart either.

    I get the file system error 1073741502 and I would like to know how to fix it please?

    I tried to do a system restore and the message is that the system restore cannot start.

    I wanted to also know if running two different registery boosters and the other has a tweek system is the right thing to do? Should OT I remove the original that always works with the computer.  I was wondering if they would be in conflict? also

    I have a disk of Home Basic windows 7 here at home. He will be allowed to use rather than the windows 7 Home premium which is loaded on the computer please? as I don't have the original disc already loaded.

    Thank you!

    Hi Shaelene,

    ·         Did you do changes on the computer before the show?

    Follow these methods.

    Method 1: Follow these steps:

    Step 1: Start the computer in safe mode and check if the problem persists.

    Start your computer in safe mode

    http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode

    Step 2: If the problem does not still in safe mode, perform a clean boot to see if there is a software conflict as the clean boot helps eliminate software conflicts.

    Note: After the boot minimum troubleshooting steps, follow step 7 in the link to return the computer to a Normal startupmode.

    Method 2: Scan the file system (CFS) auditor to repair corrupted files.

    How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

    http://support.Microsoft.com/kb/929833

    Method 3: Performs a search using the Microsoft safety scanner.

    http://www.Microsoft.com/security/scanner/en-us/default.aspx

    For reference:

    Difficulty of broken desktop shortcuts and common system maintenance tasks

    http://support.Microsoft.com/mats/system_maintenance_for_windows/en-us

  • Get the message when running Norton - OS file system error (C :), advised stopping and restarting,)

    Original title: what is system problem Partition OS operating system error (C :) file)

    get the message when Norton - OS file system error (C :), recommended stop and restart running, did not help)

    Hi catherinegood,

    1. When did you start to question?

    2. you remember to make changes to the computer before this problem? Hope this information is useful.

    This is error occurs when Norton scan, then you can check with Norton and check:

    Check the link for the support of Norton:

    http://securityresponse.Symantec.com/Norton/support/contact/contact.jsp

    http://www.Symantec.com/support/index.jsp

    If you try to run a scan, you can check out the following link and try to download the Microsoft Safety Scanner and analysis complete on your computer and check.

    Note: When you perform the analysis, there are risks of data loss you can take a backup of important data before performing analysis.

    Check out the link:

    http://www.Microsoft.com/security/scanner/en-us/default.aspx

    Hope this information is useful.

  • File system error (1003) on any attempt to access files

    First of all - I have blackberry.io.file in the config.xml file.

    Anytime, I try to read the file, extract of its existence or save it - I get the same exact message each time.

    File system error (1003).

    Handheld is a Torch 9800

    AT & T

    6.0.0.246.

    Funny, that's exactly the same code works fine on a 5 9700 version handset.

    Any ideas would be appreciated.

    TIA

    It work?

    var fileLocation   = "file:///store/home/user/documents/MCMClient.dat";
    

    or do this?

    var fileLocation   = "file:///SDCard/MCMClient.dat";
    

    I was under the impression that only the file:///SDCard and the file:///store/home/user/... are writable.  Maybe wrong however.

  • net.rim.device.api.io.file.FileIOException: file system error

    I get this error message "net.rim.device.api.io.file.FileIOException: file system error.

    FileConnection fc = null;
    try {}
    FC = (FileConnection), Connector.open (path);
    } catch (Exception ex) {}
    System.out.println (ex.getMessage ());
    ex.printStackTrace ();
    }

    The one you suggest why its kind. Thanks in advance

    "Its not allowing me" - unusual, what it actually does?

    I recommend that debug you this code initially on the Simulator.  Add a simulated SD card and try it.  You should find it easier than debugging on the device.

    Once you have your code works on the Simulator, so try on the device.

  • File system error (12)

    Hey guys. I hope that all is well!

    You have a pretty annoying problem on my current project. I use a SQLite database for the storage of telephone numbers, and these data are subsequently used to help the user to make a phone call. In the main application, these phone numbers are saved in the sqlite database. Later, when the user wants to make a phone call (IE a menu item, that I placed in the phone app), they select my menu item, which loads a popup asking what number to call. The numbers are loaded from the SQLite database to populate a list box and from there, the user can select and call this number.

    The problem is when the application is in the background when the user does this. If the application is closed, then the numbers are correctly loaded, but if the application is in the background there are some exceptions thrown, at the opening of the SQLite database, both during the access to the file for my custom log file system.

    Assistance to get to the heart of this problem would be greatly appreciated. I will surround some code below to give you a better idea of what is happening. Personally, I think it's a problem with the files already accessible by the main application, but I don't know a way to stop that without bringing all kneeling, as access still requires the main application.

    Code:

    public MyDatabase(String APP_NAME, String DATABASE_NAME)   {     String root = null;       Enumeration e = FileSystemRegistry.listRoots();       while (e.hasMoreElements())       {         root = (String)e.nextElement();           if (root.equalsIgnoreCase("sdcard/"))         {             MyLog.LogInfo("The Device has an SD Card inserted");          }     }                 // we now know that the SD card exists        path = "file:///SDCard/BlackBerry/" + APP_NAME + "/Database/" + DATABASE_NAME + ".db";        try       {
    
              myURI = URI.create(path);         FileConnection fileConnection =              (FileConnection)Connector.open(path);            if (!fileConnection.exists()) // create the file          {
    
                  d = DatabaseFactory.create(myURI);                createTables(d);//This creates the tables         }// if            else              d = DatabaseFactory.open(myURI); // [1]           staticDB = this; //[2]        }// try       catch (Exception ex)      {             staticDB = null;          MyLog.LogError("Database Creation error: " + ex.getMessage()); // [3]     }// catch }// Database
    

    [1]

    *THIS IS WHERE THE CRASH HAPPENS* we get a file system error (12) here. Is the connection already open?
    

    [2]

    not called - an exception is thrown before we can do this, but this is used to create a static accessor
    

    [3]

    "file system error (12)"
    

    The static accessor:

    public static MyDatabase getCurrentDatabase()
        {
            if (staticDB == null)
            {
                new MyDatabase(appName, databaseName);
            }
            return staticDB;
        }// getCurrentDatabase
    

    It is being used by the app and also surely staticDB must not be null? But nevertheless, it is null, and a new database is 'created '.

    Yet once again, thanks in advance if you are indeed able to help me with this problem!

    Have solved this myself. Locked the solution below in case anyone ever has such a problem themselves:

     public void deactivate()
        {
            MyLog.LogInfo("Deactivated");
            try
            {
                MyDatabase.getCurrentDatabase();
                MyDatabase.closeDB();
            }
            catch (Exception e)
            {
                MyLog.LogError("Could not deactivate");
            }
        }
    

    This goes in the database closed and main Application class when lose us focus (i.e. when the application calls turn off). Here's the closeDB method:

     public static void closeDB()
        {
            try
            {
                staticDB.d.close();
                staticDB = null;
            }
            catch (DatabaseIOException e)
            {
                MyLog.LogError("Error closing DB " + e.toString());
            }
        }
    

    I have spent ages working through this without a solution, then posted here for help and worked the answer myself in an hour. Typical!

    Hope this helps everyone out in the future

  • File system error (1000)

    Hello

    I try to write to a file on the Blackberry, by using OutputStream.write(byte[]), but I get FileIOException - ' file system error (1000).

    Where can I find information about error codes and see what means this error?

    Thank you.

    1000 means file is not open.  These are defined and explained in FileIOException

  • DatabaseIOException - file system error (12)

    Hello

    I get the error "DatabaseIOException - file system error (12) when I try to open my database.

    I recently added an alternate Entry Point at my request, in the form of an icon of the application for download. When you click on this new icon of the application, it will load up a screen that displays the value of a string variable. Initially, I thought I could just access it as 'MyClass.MyString' and get the value that the background service had put here, but it seems that they are different cases (can someone confirm this?) so the string will always be '0', since it is what its initialized to class and he will not have "access" to the value of variables in other cases (this value is then inserted into a DB).

    So, since I can't access the string, I decided I want to get the right value out of the DB. Here's the error occurs.

    I have 2 data base with 1 table of each. The database I want to access has 2 fields in the DB, an int and the string. I want the string. When I try to open the DB, I get error 12.

    I want to emphasize, the background process can use this DB in its thread, but I can't be sure, but I would have thought that I can still have read access, even if the database is already open! It will write only to the DB at the start, and will be made at the point where you click on this icon of the application.

    Can someone shed some light on this for me? My code is pretty standard:

                            URI theURI = URI.create("file:///SDCard/Databases/MyApp/MyDB");
                Database db = DatabaseFactory.open(theURI);    <--- ERROR 12 HERE
                Statement st = db.createStatement("SELECT * FROM regDB");
                st.prepare();
                Cursor cursor = st.getCursor();
                cursor.first();
                Row row = cursor.getRow();
                String theValue = row.getString(1);
                st.close();
                cursor.close();
                db.close();
    

    Thanks for any help!

    I changed the time to sleep on the other process has a higher value, and that SEEMS to have solved this problem. However, additional tests are necessary, but I hope its fixed!

    I also went back on all my calls database open and made sure I closed all the and made db = null as well. I had missed some sort if it wasn't time to sleep, so I'm confident that this is what fixed it!

  • openDataOutputStream() file system error (12)

    the code online "outstream = fileconn.openDataOutputStream (); (complete code below) throws an exception with the message "file system (12) error? the funny thing is that the exception is not thrown the first time the WriteXml(); is called that is convened first in each lifetime of the application, the write file completes successfully, but all subsequent calls after the first failure and throw this file system error? our application works on first reading an XML and then writing a (WriteXml()) if the user presses Save (which works first time), but if the user presses record once again, writing doesn't work anymore. When I close the application and then restart it, the first re-record works very well, but not the following? any ideas how to solve this problem? Cheers.

    import javax.microedition.io.Connector;
    import javax.microedition.io.file.FileConnection;
    import java.io.DataInputStream;
    import java.io.DataOutputStream;
    import net.rim.device.api.ui.component.Dialog;
    import org.kxml2.io.KXmlParser;
    import org.kxml2.io.KXmlSerializer;
    import org.kxml2.kdom.Document;
    import org.kxml2.kdom.Element;
    import org.kxml2.kdom.Node;
    
    public class Filer {
    
    private String filepath = "file:///SDCard/Blackberry/TelliT.xml";
        private String ip = "192.168.1.1";
        private String port = "80";
    
    public void WriteXml() {
    
    try {
                FileConnection fileconn = (FileConnection) Connector.open(filepath,
                        Connector.READ_WRITE);
                if (!fileconn.exists()) {
                    fileconn.create();
                }
    
                Document doc = new Document();
                Element root = doc.createElement("", "TelliT");
                Element server = doc.createElement("", "server");
    
                Element ipelem = doc.createElement("", "ip");
                ipelem.addChild(Node.TEXT, ip);
    
                Element portelem = doc.createElement("", "port");
                portelem.addChild(Node.TEXT, port);
    
                server.addChild(Node.ELEMENT, ipelem);
                server.addChild(Node.ELEMENT, portelem);
    
                root.addChild(Node.ELEMENT, server);
                doc.addChild(Node.ELEMENT, root);
    
                DataOutputStream outstream;
    
                outstream = fileconn.openDataOutputStream();
                KXmlSerializer serializer = new KXmlSerializer();
                serializer.setOutput(outstream, "UTF-8");
                doc.write(serializer);
                fileconn.close();
    
            } catch (Exception e) {
                Dialog.alert("Data could not be saved: " + e.getMessage());
            }
    
    }
    
    }
    

    You must close the stream of output as well as the connection of files.

    Note a minor - there is no reason to use a DataOutputStream instead of simply an OutputStream. Outstream-an OutputStream to change and change the call to fileconn.openOutputStream (); It will save a little bit of overhead.

  • File system error.

    Hi all

    I want to create new directory (i.e. myapplicationname) in the SD card from the Blackberry to my application starts.

    What I've done-

    FileConnection file = (FileConnection) Connector.open)

    "file:///SDCard/BlackBerry/pictures/myapplicationname", Connector.READ_WRITE);

    If (! file.exists ()) {}

    file.mkdir ();

    System.out.println ("created directory");

    }else { }

    System.out.println ("already created directory");

    }

    I get the FileIOException-

    net.rim.device.api.io.file.FileIOException: file system error

    with only 1002 error code.

    Please, help me understand the problem.

    Thank you

    Mary

    http://supportforums.BlackBerry.com/T5/Java-development/create-a-folder-in-file-system/m-p/19640

    This link might help u?

    give Kudos if you find the solution.

  • Partition to opt on fabric interconnect an includes file system errors

    After a downgrade from painful recovery (failed upgrade from 2.2.3d to 2.2.6d) everything works again, but I see

    Partition to opt on fabric interconnect an includes file system errors (see attachment)

    To remedy this unpleasant error advice are appreciated.

    Hello Walter.

    The bug that you run is;

    https://Tools.Cisco.com/bugsearch/bug/CSCus79160/?reffering_site=dumpcr

    I stumbled upon this problem in the past, the TAC will load the debugging plugin and just check a few blocks. Anika, a system launch is another fix but it is a longer process, if you open a TAC case don't forget to mention the bug above and they can try this work around first.

    I would like to know if you have any other questions or need help.

    Qiese Sa'di

  • A file system error prevents Flash catalyst to launch with adobe creative suite CS5

    Hi all

    I am using Windows 7 64 bit operating system. I installed Adobe creative suite CS5, which is 32-bit. The application is installed in C:\Program files (x 86).

    When I try to run Adobe flash catalyst, he throws an error "file system error prevents Flash catalyst to launch."

    Someone meets the same kind of mistake. No idea why is it being caused. How to solve this error.

    Kind regards

    charch

    Solution: -.

    (1) right-click on the shortcut file "Adobe Flash Catalyst CS5.lnk"

    2) click on the shortcut tab

    (3) add the following setting -data "catalyst %APPDATA%\Adobe\Flash" (after "C:\program file (x 86) \Adobe\Adobe Flash Catalyst.exe ')

    This step will redirect files and folders created when running the user profile.

    Kind regards

    Kumar Baillet

  • boot problems after "disk error-checking/control - automatically fix file system errors.

    I ran the two options 'check disk' after deleting some old programs and was prompted to restart. When it restarts it was all white screen, then I stop after waiting a few minutes using the power button. now it won't start at all - I have white screen and cannot even get into safe mode by pressing F8. white screen and the fan runs. I is not original boot CD, so tried a CD recovery Norton but would not start from that. I checked the monitor cables.

    It's a 2002 eveshamvale:
    Windows XP Home Edition Service Pack 3 (build 2600)
    Board: Gigabyte Technology Co., Ltd. 8ID533 1.x
    The bus clock: 100 MHz
    BIOS: Award Software International, Inc. 6.00 PG 11/11/2002

    would be grateful for any ideas.
    Thank you

    If you used the power switch, you can inadvertently damage your file system, so before wasting time to try a bunch of things, I could do this (or you may be wasting a lot of time to try things too):

    The question was preceded by a loss of power, aborted reboot or abnormal termination? (This includes the plug pulling, buttons power and removing the battery).

    These can cause corruption in the file system that must be fixed before you do anything else.

    If none of these events occurred (or even if they have not taken place), you must verify the integrity of your file system before anything else (especially "try" things).

    There is zero logic to begin to try to begin to try to modify or copy files to a hard drive that has a corrupted file system, so this must first be fixed using the XP chkdsk program and run chkdsk on your hard drives may solve your problem completely.

    Use the XP Recovery Console to check the file system on your HARD drive and fix the problems and then try to start your system - this may be all you need to do.  Or, you are welcome to just start trying things that might work.

    Boot into the Recovery Console Windows using an XP bootable installation CD.

    If you have no XP bootable media (or aren't sure you have) create a bootable XP Recovery CD of Console and do not forget.

    This is not the same as recovery disks that may have come to a store to purchase the system.

    You can make a bootable Recovery Console CD by downloading an ISO file and burn it to a CD.

    The ISO bootable image file you need to download is called:

    xp_rec_con. ISO

    Download the ISO from here:

    http://www.mediafire.com/?ueyyzfymmig

    Use a new CD and this simple and free program to burn your ISO file and create your bootable CD:

    http://www.ImgBurn.com/

    Here are some instructions for ImgBurn:

    http://Forum.ImgBurn.com/index.php?showtopic=61

    It would be a good idea to test your bootable CD on a computer running.

    You may need to adjust the computer BIOS settings to use the CD-ROM drive as the first device to boot instead of the hard drive.  These adjustments are made before Windows tries to load.  If you miss it, you will need to restart the system again.

    When you start on the CD, follow the instructions:

    Press any key to boot from CD...

    Installing Windows... going to pronounce.

    Press 'R' to enter the Recovery Console.

    Select the installation that you want to access (usually 1: C:\WINDOWS)

    You may be asked to enter the password (usually empty).

    You should be in the folder C:\WINDOWS.  It's the same as the

    C:\Windows folder that you see in Solution Explorer.

    The Recovery Console allows base as file commands: copy, rename, replace, delete, chkdsk, fixboot, fixmbr, cd, etc.

    For a list of the commands in the Recovery Console, type help at the prompt of commands or read on here XP Recovery Console:

    http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/recovery_console_cmds.mspx?mfr=true

    A good idea before you start things must first verify the integrity of your file system by using the chkdsk command.

    In the command prompt window, run the chkdsk command on the drive where Windows is installed to try to fix any problems on the afflicted player.

    Running chkdsk is fine, even if he finds no problem.  It won't hurt anything to run it.

    Assuming your boot drive is C, run the following command:

    CHKDSK C: /r

    Let chkdsk finish to correct the problems, he could find.

    It may take a long time for chkdsk complete or they seem to be "stuck".  Be patient.  If the HARD drive led blinks always, chkdsk is something.  Keep an eye on the amount of the percentage to be sure that it is still making progress.  It may even seem to go back sometime.

    You must run chkdsk/r again until it finds no error to correct.

    Remove the CD, and then type "exit" to exit the RC and restart the computer.

    You have not to set the BIOS to boot the disk HARD since the CD won't be.

Maybe you are looking for