Find the latest Firmware updates for your HP printer

Similar Questions

• Cannot find the latest firmware for the Toshiba 40TL838G

  Hello

  I am trying to download the latest firmware for the 40TL838G model, but I'm not.

  Where can I find it?

  Thank you.

  The same has been asked in this thread
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=73914

  We can receive the update only via a network update
  In which case you will not receive updates via the network, your firmware is up to date.

• Can not find the latest Firmware for QX10

  I got an automatic notification that there is an update of firmware for my QX! 0 a couple of days. I did not take in the details then. However when I search the site Support of Sony, it only refers to an update in dated date in 2014.

  Does anyone know the exact URL to get the lates firmware?

  Thanks in advance.

  The latest version of the firmware for the DSC-QX10 is 3.00 released 04 14, 2014.

  You can find the new firmware at: http://esupport.sony.com/US/p/model-home.pl?mdl=DSCQX10&LOC=3#/downloadTab

  Select the operating system of your computer (the update of the firmware is available to run on Mac OS x and any version of Windows XP 8.1.) and click on the Firmware.

• WRT160N v2: the latest firmware update went wrong!

  Hello

  I just bought this new thing, it is not connected to the internet (wrt160n-> cable modem-> internet)

  so I tried the last thing: upgrade to the latest firmware 2.0.02
  The upgrade - trial went fast enough at 98%, but remained there for about 3-5 minutes.

  Then finally: successful update.

  It has rebooted, my computer got an IP address again, but still no internet.
  So I went to the page of configuration of the wrt160n, entered ID + password and then...

  ... a screen almost empty! No menu, page actually kind of corrupt.
  I unplugged the router from the power, waited for 60 seconds, retried: same question.

  Any thoughts?

  Thank you!

  Did you try a hard reset, use a pen that I think just next to the power plug to the back of the router there is a reset button with the router connected to the power hold it down until you see the flashing front light put your factory after that

  1. set up your router using the cd that came with it

  2. After setting up is done and you are able to go online try the update again

  that should do the job

• Toshiba 37BV701G - where to find the latest firmware

  Hi, I would like to update my TV firmware. Current is 0.3.5.a. I can't find the file to download.

  Thank you

  For customers who live, in Europe and all TV sets purchased in Europe firmware is downloadable from this portal
  http://www.Toshiba-OM.NET/firmware.php

  In case your TV device is not listed, the update of the firmware is not available

• I can't find the latest driver ATI for Tecra A7

  Hello
  I have a problem and I hope someone could help.

  I have an ATI Radeon X 1600 in my book and I need the latest driver for it, but the driver which is located on the site of ATI don't like my computer, and he indicated that he could not install on my computer. I think that there is not supported computers laptop toshiba. And I could just found a driver what version number is 8,292 and his since 2007.
  Can someone tell me a site or something where I can find a newer driver for my computer? Or other options...

  Thank you
  Andrew

  Hello

  As you say the Tecra A7 was equipped with ATI M56P(256MB) ATI Radeon X 1600 graphics card.
  I discovered that the Satellite A100 PSAA9E and Satellite Pro A100 PSAACE were equipped with the same driver

  To verify the version of the driver that is designed for both series of books above.

  Good bye

• a window said "flight simulator does not work with your video card. Make sure you have the latest drivers installed for your video card.

  Flight Simulator X not would allow me to get it because it says I need to update the video card. I think the problem was that I finally erase all memory of the computer using a special cd, because once I have done this and downloaded the software again, it stop working

  Hello el 24, welcome.
   
  There are a few possibilities as to why you see this message. There is a chance that you do not have your drivers graphics/display installed or configured correctly.
   
  We will need to know the brand and model of your computer to properly route you to the right path.
   
  Once we have this information, we can see if we can provide you a link to the Web site of the manufacturer of your PC to download the driver.
   
  Let us know,
   
  Thank you!

• How can I find the right patch / update for Photoshop CS 6 and bridge can read my raw files from Canon 5 d MKIII.

  I reinstalled Photoshop and now I can't read my raw files...

  If the menu help > updates does not work. Try to download and install the update of ACR to Photoshop CC 8.6 if done or work try by downloading and installing the ACR with the DNG Converter 8.6.  If you install that does not install in CS6 and bridge common ACR plugin folder copy ACR 8.6 in this folder after renamed it existing ACR here.

  2014 all updates of Adobe CC: Direct for Windows download links | ProDesignTools

• How to set the Destination of scanning for your Hp Printer in window - 7

  How to set the scanning for your printer Destination is a common question is asked.  I am including a useful video that will guide you in the process.

  I hope this video helps.

• How do I find the product version updates for a particular family pack.

  Hi all
  
  Let's apply 11i.HR_PF. K.Delta.4 (7666111), how can we find this all products of his going to update and what are these versions.
  
  Ex: We are in 11i. PAY. Mr. so is applied 11i.HR_PF. K.Delta.4, what version we will go in.
  
  Can you please advice on where I can get these details.
  
  Thank you
  Rakesh

  Hello

  You can find these details in the document Family Pack - see (Note: 828973.1 - on Oracle HRMS Family Pack cumulative hotfix K 4 (7666111 11i.HR_PF.) K.DELTA.4)).

  In addition to this document, please consider revising (Note: 849747.1 - known issues on top of Patch 7666111 - 11i.HR_PF.) K.Delta.4 (11i HRMS RUP4)).

  You can also search My Oracle Support "7666111", there are a few bugs reported on top of 11i.HR_PF. K.DELTA.4

  Thank you
  Hussein

• Windows XP svchost.exe problems. Cannot find the latest updates for windows xp.

  Hello, this is my first time on the Microsoft Community page.

  I have a very strange problem with automatic updates svchost.exe and windows. I know that automatic update of windows, has been known to cause problems on XP and there is thus CPU utilization of memory leaks. Last night, I tried to install the latest windows XP updates, with automatic tool. The tool hanged during the process. Not sure why exactly. I never had a problem with it. I've been running Xp SP 3 for more than five years. In any case, I rebooted my system and checked to see if the updates actually treatment. They do not have. Then I went to the windowsupdate.microsoft site. I was trying to these updates. The scan never completed, he just constantly checked, for about 45 minutes. I decided to do some research. I found the C:\Windows\SoftwareDistribution folder "fix" online. He kicked, I renamed the file. And then disabled auto updates and restarted my computer. After windows starts, I re-activated automatic updates and waited. Nothing happened, so I did some research more. I noticed that svchost.exe uses about 25% the use of the processor. Normally my treated systemidle is 99%. I used Process explore and isolated the wuauclt.exe under the svchost.exe file. When I disable automatic updates executable, it is up to a full 99%.

  I'm not sure why it uses 25%, when I look at the actual use of the memory for the wuauclt.exe, it is only using about 17 k of memory. Which is quite low. I have not turned on microsoft update, starting in the configurations of parameters at windowsupdate. I know that in the past, that has been a problem and swallowed up system resources.

  Any advice would be helpful. Thank you in advance.

  There are a lot of threads on this forum - and many others - this problem - just try to do a Google search for UPDATES of XP SVCHOST - hits now more than 8 million.

  But to save you the trouble of tracking down the fix OK here is the short version

  1. disable automatic updates using Control Panel icon

  2. restart the computer - SVCHOST is now not going crazy

  3. check which version of Internet Explorer you have installed IE8, IE7 or IE6

  4. download and install - the links below - the good update for Internet Explorer.

  Assuming you have Windows XP 32 bits here are the direct download links:

  IE8: IE8-WindowsXP-KB2898785 - x 86 - ENU.exe
  http://www.Microsoft.com/en-US/Download/details.aspx?ID=41404

  IE7: IE7-WindowsXP-KB2898785 - x 86 - ENU.exe
  http://www.Microsoft.com/en-US/Download/details.aspx?ID=41442

  IE6: WindowsXP-KB2898785 - x 86 - ENU.exe
  http://www.Microsoft.com/en-US/Download/details.aspx?ID=41458

  5. Once installed, you can reactivate the automatic updates and using Windows Update.

  Note: The bug also affects access via Windows/Microsoft Update Web site.

  KB2898785 is the "Cumulative Security Update for Internet Explorer" (December 10, 2013)

  There is a bug in the function of automatic update under XP running the SVCHOST process at full CPU load (100% or 50% or 25% depending on the number of CPU cores you have). If you have a Quad core CPU the bug works the CPU at 25% (a carrot out of four) and eventually battles through a conclusion - but if your computer is a single old Celeron or Pentium bug works the CPU chip at 100% load for many, many h/solid.

  Faster your processor and RAM than you seem to make a radical difference to the actual times are waiting for you maybe search for updates complete. Most of the old core systems were never designed to deal with this kind of situation and can easily overheat. This is especially true of laptops and desktop systems older where the radiator can be partially blocked with fluff and hairs of animals - which could cause blockages or stops!

  Microsoft said last month that the updates of Internet Explorer are treated differently from all the other updates - which is originally the XP update engine run so slowly as to appear frozen. If the update service finds that you don't have the latest version of IE that is currently available, it starts to search the entire tree of updates of IE to see what it takes - rather than offering just the cumulative current update for your system.

  But if you manually install the update yourself update Internet Explorer service is fully updated and is not search for updates of IE. But until Ms. fix it will still occur whenever a new update is published.

  MS said that intend to prune the IE updates database so that only the main cumulative updates have been offered when a search has been launched - it did not in time for the update as it should of November and obviously has not arrived or worked either in time for the December Update!

  MS say they hope to have a fix before the January updates are released (Patch Tuesday) - that the problem will be activated once the next update Cumulative of IE is released.

• Where can I get the latest Firmware UJ - 822S for Portege S100?

  I'm looking for the latest firmware for this drive. The drive came with the Portege, and I know that they are specific OEM. There are later versions of the firmware available on other sites of manufacturers, but these will be simply screwed to the drive. I'M NOT AFTER RPC-1 firmware, just the last available if possible.

  Thanks in advance,

  PoB0782

  Hello

  Is there a special reason why you want to install new firmware, maybe some problems burning?

  I put t know where you can find the latest firmware for this phone, but if you Google a bit you will find many forums, such as http://forum.rpc1.org/.

  You will find useful information and comments about the firmware and the results. I just want to say that you should be careful about this. I put t know how old your unit and if the warranty is still valid, but please note that, after the installation of the firmware non-Toshiba, warranty for ODD will be lost. In the case of the STRANGE is defective it is not replaced.

• R7000, problems with wireless connection after the last firmware update 1.0.6

  I recently updated to the latest firmware available for the R7000...

  The upgrade went well and my Wired PC all connected without any problem, but several of my wireless devices were unable to connect to the WiFi. I have my cell phone Wifi (Android phone) kept gives me an error of authentication, but was able to connect to the network comments... weird...

  I started firmware 1.0.4 and everything worked well again... it seems that the new firmware is buggy.

  The Firmware versions listed above are only for the first three issues, to save typing, but you get the version that I use...

  Nick

  Hello

  I would like to let you know, I've improved in 1.0.6 last night and everything worked. The difference is this time I had to reset my router to the factory settings using the reset hidden at the back button and hold the button for about 7-10 seconds. This resets the router to the factory settings. I then had to re-enter all my IP address reservations and the word block list, but all my wireless devices were able to connect. The last time I did the upgrade, I just restarted the router, and I had read that I had to do a factory reset to operate correctly.

  It would have been nice for Netgear arrive at a way to extract Information form my version last-place back... it would have saved me a lot of time...

  Good luck

• How to find the level of update rollup

  Hello
  
  I would like to know the current level of update rollup applied for all SCM modules and finance, listed below.
  
  We are in * 12.1.3 with 11.2.0.3 database on Linux 5 *.
  
  Supply chain
  1 oracle I have procurement (ICX)
  2 buy a (IN.)
  3 sourcing (PON)
  4. the inventory (NAV) (Note: WMS not installed)
  5 order Management (Ontario)
  6 Shipment Execution (WSH)
  7. cost Management (CST)
  
  Finance
  1. Accounts Payable (SQLAP)
  2. receivables (AR)
  3. cash Management (CE)
  4 Assets (OFA)
  5 general Ledger (SQLGL)
  6 subledger Accounting (XLA)
  
  
  Please help me how can I find the required information, waiting for your answer.
  
  
  Thank you

  user11969666 wrote:
  Hello

  I would like to know the current level of update rollup applied for all SCM modules and finance, listed below.

  We are in * 12.1.3 with 11.2.0.3 database on Linux 5 *.

  Supply chain
  1 oracle I have procurement (ICX)

  9249326 R12. ICX. B.3 ICX

  2 buy a (IN.)

  9249328 R12. In. in. B.3

  3 sourcing (PON)

  9249327 R12. PON. B.3 SOP

  4. the inventory (NAV) (Note: WMS not installed)

  9242191 R12. B.3 INV INV.

  5 order Management (Ontario)

  9244129 R12. B.3 ONTARIO HAVE

  6 Shipment Execution (WSH)

  9244435 R12. WSH. B.3 wsh

  7. cost Management (CST)

  If his oracle landed cost management
  9244459 R12. INL. B.3
  Please confirm its INL or CSE?

  >

  Finance
  1. Accounts Payable (SQLAP)

  9244867 R12. BPM B.3

  2. receivables (AR)

  AR ar 14689993 B R12.ar.B.3

  3. cash Management (CE)

  13024047 what this R12.ce.B.3 B

  4 Assets (OFA)

  9244841 R12.FA. B.3 fa

  5 general Ledger (SQLGL)

  9244874 R12.GL. B.3 gl

  6 subledger Accounting (XLA)

  9244854 R12. XLA. B.3 xla

  Please confirm each of them by running the following query
  Select patch_level in the fnd_product_installations where patch_level like '% ICX % ';

  like wise

  ;) AppsMAsti ;)
  sharing is caring

• OfficeJet Pro X451dw (CN463A): updated the Firmware says X451dw "EC Firmware Updater does not contain updates for your device."

  I'm trying to update the firmware on my HP Officejet Pro X451dw (CN463A), but the firmware update fails with the error "This Firmware Updater does not contain updates for your device." More precisely:

  1. With the help of EWS, I confirmed that my current firmware is very old (it lists the firmware version of BWP1CN1315FR, which means 1315FR, right?, dating almost the time I bought the printer about 3 years ago).
  2. I downloaded the firmware ("OJP_X451dw_R1640A_updated.dmg") was last updated, copied 'HP Firmware Updater' in /Applications and then he ran.
  3. It shows my printer in the Device Discovery list. I selected and clicked on continue.
  4. He thinks for a while, displaying "recovery information...". »
  5. After a wait of 30 seconds (approx.), it displays "EC Firmware Updater does not contain updates for your device."

  Any suggestions?

  You're welcome @justkwin.

  Here is the utility of a Mac computer:

  FTP://g4u0180.Houston.HP.com/FTP4/pub/softlib/software13/printers/pentane/OJP_X451dw_R1548A.dmg

  Kind regards

  Shlomi