First Firmware update

Similar Questions

• HP first Firmware Update Failed (104)

  I heard that there is a new firmware for the HP award.

  I connected the calculator for the HP connectivity Kit.   It is an update for both the Connectivity Kit itself and for the calclator.   He managed to update the connection kit, but I can't update the firmware of the calculator.

  I'm on Windows 7 64 bit.

  My current firmware revision is: 2013 8 13 (5106)

  According to the new firware is version_20131125.

  I tried to restart the PC, using a different cable and another USB port.

  The connectivity kit seems to have a solid with the Calculator link because I can view/change settings, etc.

  After a failure the firmare update, I for trombone reset the calculator.

  Any help would be appreciated.

  Sorry in advance if this has already reported and resolved.  I did a search of the forum and have not seen everything about this new version.

  -TIA

  Hi!, gablinger:

  (1) charge the battery to 100%.

  Please, check this link... http://www.educalc.NET/2336439.page

• first firmware update went wrong...

  Hi all

  I have a wrt54g (8.1) who has acted a bit funny so done some searching on Google and followed the instructions to install a new firmware.  First of all, the installation failed, double checked to make sure I downloaded the correct file (FW_WRT54G_8.1.09.02_US_20071227.bin), made a reset and power cycle.  Checked the data again and everything on the configuration of the router has completely disappeared.  Each entry has NA next to him...

  > help!

  You can't put the same settings as you have before at least that you could not save the configuration. However, you can reconfigure the settings and still get online again. The following link can help.

  Different ways to set up your Linksys wireless router

• Wan interrupts the connection after the firmware update

  Looks like the latest firmware upgrade is the source of the problems.

  I've just updated my timecapsule 1 TB of first generation version 7.6.7 and my 3 TB timecapsule new version 7.7.7

  Both are connected to the router of the provider of Internet services and extend the network even in my house.

  WiFi is stable until the upgrade, but now the connection is lost every few minutes or seconds.

  Both versions are later to the respective timecapsules.

  I end up having to downgrade if no solution is found.

  I powered the two market still nothing does not. Redefine the network and tried both hidden and not hidden, yet once nothing doesn't.

  Any ideas on what is causing the problem?

  Well, since nobody seems to have an explanation, and Apple are not out with firmware update after 7.7.7 and 7.6.7 I decided to downgrade the firmware to the previous version. I now run version 7.7.3 on the new 3 Tb Time Capsule and 7.6.3 on the 1st Gen Time Capsule. So far, the network is stable. Using WiFi Explorer Ii see that they use channel 6 and 8 respectively. Signal is strong and no dropouts have taken place so far. Hope the issue is resolved in the next firmware update.

  As I read in another post: firmware update does not solve a problem, you didn't. However, it can create a problem that you didn't.

• TimeCapsule downgrades WiFi 2.4 GHz after applying the firmware update v7.6.7

  After applying the firmware update v7.6.7 free WiFi to TimeCapsule is now 2.4 Ghz instead of 5 Ghz.

  It was the update of the firmware with certainty that has made this... no doubt about it:

  • My mouse bluetooth interference notice when my MacBook is connected to WiFi 2.4 Ghz;
  • Before the update, everything is OK
  • After updating, my mouse mouse start jittering
  • < alt-click > WiFi icon in the menu bar confirms: the connection is now 2.4 Ghz

  Restart to e TM Mo doesn't change anything.

  In the TC WiFI options tried to put another name to the network successfully, but only 5 GHz can not connect to it: timeout error every time.

  Tried the hard reset of TC and reconfigure the WiFi... the same result, but with a difference:

  • Setting an SSID separated for 5 GHz connection (in the WiFi options) has now created a network I can access.
  • However, this is not the best solution... I don't want 2 SSID.

  It is not the first time Apple breaks things with updates... and I see people move away from Apple to this kind of situations.

  I also had bad experiences with OS updates lately and postpone the as much as possible.

  The problem is that I can't go back... or can I?

  Any help is welcome.

  THX

  The problem is that I can't go back... or can I?

  Of course, you can, but it may or may not help.

  Open AirPort Utility

  Click on the image of the AirPort base station

  Hold down the option key on your Mac while you click on the version number of the firmware

  A drop down menu appears

  Choose the version of the firmware you want to use

• Unable to launch SSD Q300 HDTS748EZSTA firmware update

  This player has a fresh install of Win7.

  Currently on SAFM11.1 and want to update to 11.2

  No other programs are running by the utility of the list firmware update "before you begin".

  The following message is received after the warning on the reboot of the pc:

  Impossible to prepare the system to update the native mode. Try again or contact technical support.

  What should I do to get past this error? I have to start this process all in safe mode?

  You must run the update of the firmware in safe mode. (Even if the system is loading press F8 and use mode safe mode with LAN). But there is a problem after update the firmaware.
  If you use TOSHIBA Storage Utilities v3.10 there is a possibility that your system crashes (you should first uninstall it).

  There is no possibility of connection to Windows after restart. I did an experiment and after formatting SSD, I installed a new copy of Windows 7 Pro SP1. The result was the same, it worked until the installation of the utilities of storage TOSHIBA v3.10.

  There is clearly a software problem, but I have not found another solution (do not to install the utilities of storage TOSHIBA v3.10)

• Portege R400 - Firmware update fails for 3G card

  During the Firmwareupgrade of the G 3 embedded (expedite EU870D) in my protégé R400 card, I have a power fail. The next time you start, I can't countinue with the upgrade. The card no longer works.

  The Modem and the COM Ports, I don't see in Device Manager. Is there a solution for this error? Thanks for the help!

  Pumbkin

  Why do the update of the firmware?
  You should do this only if the Vodafone SIM card does not work properly!

  I found this info that pop ups before performing a firmware update!

  + Atten-tion of the FW update: +.

  + Please do not forget to read carefully before place the FW. +

  + 1. FW update is not necessary when the Vodafone SIM card works fine in the customer environment s. run the FW update only when the Vodafone SIM card is not detected. Please note that the FW is more reversible to the previous state once updated. +

  + 2. This upgrade tool will apply to the following models with built-in 3G module: +.

  + Portege R400 +.
  + Portege R500 +.
  + Tecra M9 +.

  + 3. Please leave 3G communication and close the connection utility before running the FW update. +

  + 4. Close all applications before you run the FW update. Please DO NOT launch any application during the upgrade process. +

  + 5. Please ensure that you use an AC adapter to power the computer during the process of FW update. Power failure during the upgrade process can lead to failures of 3 G modem. +

  + 6. Please DO NOT sleep/standby extended/Shut Down the computer during the process of FW update. This can lead in mode 3G +.

  So please first these points before you is trying to update the firmware!

• Satellite M30X-122: UJ-820 s Firmware update?

  Sorry to post here, but Toshibar don't offer no matter what contact email address
  I use a Satellite M30X 122 with an optical drive UJ-820 s.

  Nero does not Duke my blank verbatim 16 x DVD discs. When I put a disk empty in to burn a backup, there is no Duke them.

  Word for Word recommends an update firmware for the optical drive. But I can't find anything on the toshiba support pages.

  Any idea?

  See you soon
  Rudi

  Hello

  First of all, you should try different CD/DVD. It is possible that the drive doesn't recognize several media. About the firmware, well I found a firmware update in the download area of driver for Satellite M30x laptop.

  Check this box:
  http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp?service=EU

• HP zBook Studio G3: zBook Studio G3 - DEATH BY INTEL ME FIRMWARE UPDATE

  WARNING!

  DO NOT INSTALL THE UPDATE OF THE COMPONENT OF THE (COMPANY) INTEL MANAGEMENT ENGINE FIRMWARE!

  http://h20566.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=8934841 & swItemId = ob_159465_1 & swEnvOid = 419...

  Component Firmware Intel management engine (ME) (American International)

  11.0.0.1194 Rev.A
  December 1, 2015

  We bought 5 of these laptops for our Engineering Department and I was against a tight schedule to get them deployed (the next day). I started working on obtaining a set of installation with the necessary software and then I just want to clone one for the other 5.

  I did a clean install of Windows 10 and installed all the drivers from the HP site. Then I ran Windows updates until everything is up-to-date. I disabled Windows Defender. Now all that remained was update the firmware BIOS, Intel ME and Thunderbolt using the downloaded utilities since the page drivers. The BIOS installed fine, but it's a really weird update process. Due to the beeps and lights blink during his work. There is no progress bar to let you know if she is doing anything. At some point, as the beeping stop but it's still really work. Then he starts and updates another part of the system and so on. Anyway, that everything worked fine. No problem with the update and Windows 10.

  So I ran the update of the Firmware of Thunderbolt and open up a command window saying that it couldn't find the controller. It looks like not there nothing after that point and just closed.

  Finally, I ran the Intel Management Engine firmware update utility. He opens a command window and says that it is loading the file and check and so on. Then he wrote the Flash file and takes a minute or two, doing so. Once it's done, the firm order window and back to business as usual... until you restart. Once you do this, the system is toast. It does not start. Black screen, fans run at high speed and the CapsLock and NumLock bulbs only 5 slow flashes indicating that there is something wrong with the motherboard. I'm starting a supported by HP chat session.

  I am told to disconnect the battery. To access the battery, you need a bit T - 8 Torx and you unscrew 11 screws to remove the grill cover and low fan (pedestal). I did that and disconnected from the battery. Reconnect after a few minutes and tried to start. Nothing, same thing. The support agent told me that a technician on site should be sent to replace the motherboard.

  While the lower lid has been opened, I noticed that there are two small LED lights near the SSD. There are supposed to be the diagnostic lights and I found an article in the service manual indicates if one of the LEDs is lit, the motherboard should be replaced. This lights a few seconds after the connection of the power supply for the laptop or by pressing the power button.

  I asked the support agent if they knew why it happened, but they did not know.

  So, I got 4 portable more to work with. I took off the dead laptop SSD and put a charge in a brand new out of the box. Started by and on the desktop Windows 10. This laptop had BIOS v1.03 on this subject so I ran the BIOS updated and rebooted. All right. At this stage I myself asked to perform other upgrades of the firmware or not. I thought that I had a 50/50 chance and I'm the kind of person that simply be whether it was a fluke or if there really was something seriously wrong with the update of the Intel ME firmware. He ran while first instead of love at first sight to date. Update Intel did ME the same thing before, opened a window to order, checked and then flashed... and after a reboot I got another laptop dead.

  At this point, I shook my head and frowned, looking at the HP logo.

  I tried calling support, but their laptop zbook/computer service has been closed from 10 is no support by phone or chat support. I have to wait until the morning to make a call in warranty for this second laptop dead.

  The Intel ME firmware update released on download of HP ZBook Studio G3 section was not compatible with these laptops and caused the laptop no longer starts. Only an exchange of motherboard could solve the problem. HP since then changed the link to the Intel ME firmware update for the appropriate softpaq.
  
  Those who had run the update of the bad firmware and their laptop brick had to call the HP technical support to schedule a replacement motherboard on the spot.

• FS728TP attention firmware update!

  Too bad, you can ruin a good switch poe by a stupid firmware update. Tried to update my FS728TPv1 to the latest 5.0.0.8 3.0.0.22. Downloaded the zip file, you start the procedure to update with discovery of the smart wizard, message received "updated successfully"... but after reboot the switch is bricked. Did some reading, found I'm not the first guy with this case, should be updated first, startup code from 1.0.0.2 to 1.0.0.5. But it was not a code starting update file in the zip! I found somewhere on the netgear firmware french site the oldest 5.0.0.6, which contains ng_fs728tp - V5006.ros and ng_fs728tp_boot - 1005.rfb. I feel so stupid, I'm?... to open the switch box, found 88E6218-LG01 Marvel, used on some routers 10 years ago chip. anyone find a procedure to revive the switch, a tftp, a series or something connection session. I know netgear offer guaranteed for life and replace the switch, but not my case... just feel sorry a switch of the brick work

  There is a solution, in case you brick the switch to update the firmware, do not update the boot code appropriate. The boot code is some program low level similar to the bios on the card. Did some deep research on Marvel 88E6218-LG01 Chipset, I found somehow that pin 52 and 53 are Rx and Tx respectively to integrated serial UART. The two signals are 12 (Rx) and IC U27 PIN 11 (Tx). The IC and passive components around him are not soldered because the switch is not a serial console. Near U27 is the serial J8, not used. The U27 is a similar to max232 chip. The idea is to make a connection with the switch using p52 series = Rx, p53 = Tx and, of course, GND, I soldered the wires to p11 and 12 of the U27. Then do a session in Hyperterminal using baudrate = 38400, data bits = 8, parity = none, stop bits = 1, flow control = none. Power on the switch, you will see power on self-tests, boot network device based on 88E6218 software version with ARM946E-S then: autoboot in 2 seconds, press return or ESC to interrupt and enter the dance. In those 2 seconds interval if you press the INPUT switch goes to the start with 6 options menu: 1 = software download 2 = flash file Erase 3 = 4 = diagnostic mode password recovery procedure entry 5 = Set baudrate terminal 6 = back. Choose option 1) then the switch is waiting for the firmware file "code using XMODEM download, $$$ writing and waiting...". Now go to hyperterminal transfer, send file > Browse for firmware 3.0.0.22 .ros (before update wrong firmware), choose the XMODEM Protocol, and then click Send. File transfer begins, will take about 25 minutes. After that the switch restarts correctly, and discovery of the smart wizard he found. Update the firmware on 5.0.0.6 family must 1.0.0.5 to update the BOOT CODE. The boot - 1005.rfb can be found on this website: http://www.netgear-forum.com/forum/index.php?s=7d23113dd1660e3c9d613aa739513390&showforum=704 , in 5.0.0.6 zip of the firmware. Have fun...

• SOLVED: Slow wireless internet passthrough after firmware update

  If I first bought a Nighthawk in July 2014 and it was great for a while. Then in the notice happened a few months my streaming services are jumping and more than usual buffering (which was almost never with the Nighthawk).

  I have a connection of 110Mbps (Comcast and through a SB6141 modem), but all of a sudden was only getting 10 Mbps (or less) passthrough on 5 G wireless band (at the beginning of the speed test would sometimes up to 50 Mbit/s, but on a few seconds would fall to nothing..)

  Cable speeds were very good. Always 110Mbps +. Tried several different channels and factory reset the router, wireless speed was still slow. Connected to the Netgear website and submitted a support ticket within 2 hours they sent me with an RMA number and the next day a new unit has been FedEx would be for me. Support rep Tech says it's a problem of material known in some units... I was super impressed with the customer service, it was seriously a no replacement of hassles that took every 15 minutes of my time.

  EXCEPT when I got the replacement router in the next few days, he had the SAME PROBLEM. As soon as the new router is on and I'm connected, I've upgraded to the latest version of the firmware, done a factory reset and down Speedtest. And I had the same problem: speed internet passthrough on all my wireless devices has been terrible. Less than 10 Mbps when I have a connection 110 + Mbps. (Wired speeds were great, it was not a problem of modem or provider).

  Again contacted support and they asked me to download the latest firmware on laptop and upgrade the router manually, do a factory reset before and after the upgrade. They also told me to try to disable WMM (made no difference speed passthrough, but lower my laptop connection between 433Mbps to 54Mbps speed!).

  I tried this... still slow passthough wireless speed.

  The only thing that has changed since I first got a Nighthawk in July 2014 (and I've run speedtests then and had a speed 110 wireless + Mbit/s at the time), is that the firmware has updated several times... makes me think...

  I downloaded the Netgear support the past 5 versions of the firmware for the Nighthawk. http://downloadcenter.netgear.com/en/product/R7000#sear...

  I then manually downgraded the Nighthawk to each previous version (do a factory reset before and after each installation) and ran Speedtest every time. Once I have got down to the R7000 Version - V1.0.3.24_1.1.20 (released 12/02/14) and ran a Speedtest, the PROBLEM has BEEN RESOLVED. Speed wireless devices (laptop, HTC a M7 and iPad Air 2) were all back up to 110Mbps or more!

  Hope this experience helps someone else... If your are affected by the passthrough slow internet speeds and it is not your connection speed (i.e. radio parasites) that is the question, there seems to be a serious problem with the latest latest versions of couple... Try downgrading to the R7000 firmware version - V1.0.3.24_1.1.20

  UPDATE: Yes, I actually tested the speed with several different devices (a laptop HP HTC a M7 and Nexus 9) each on 5G band, all compatible with the latest updates ac. I also used a few test sites of different speed (speedtest.net, comcast speedtest, cnet speed test), not had the same result all devices and hosts.

  However, I actually got in touch with Netgear L2 support for the last month... beta test a few different versions of the firmware of the Nighthawk and even spend more than an hour on the phone one night with a nice guy who told me he was on an island in Southeast Asia, part of the Philippines... This is where Netgear technical support is to halfway between China where they build them and Taiwan where engineers are. After trying all tweak he could think for an hour and not get better speeds wireless, he finally dropped out and wished me a Merry Christmas lol. Not one of these beta firmware made a bit of difference, and I hate the hours that they made me screwing around with them!

  BUT today, they released vR7000 - V1.0.4.14_1.1.50 http://support.netgear.com/product/r7000

  And to my surprise it actually worked! Not only my high speed wireless is returned (120 + Mbps)

  http://www.Speedtest.NET/my-result/4078979293 (laptop)
  http://www.Speedtest.NET/my-result/a/1131321713 (nexus 9)
  http://www.Speedtest.NET/my-result/a/1131332778 (htc a m7)

  but also my Seagate SRD0SD0 previously incompatible (3 TB) USB 3.0 external hard drive works now, too. What a bonus! The reason I bought the Nighthawk was to use as Server DLNA and the monster external HD I picked up 6 months ago only was on the long list of those incompatible with this capricious router.

  But now everything works (at least for now).

  P.S. Maybe it's in my head, but I swear to you that since the last firmware update when running speedtest now or file transfer (while heavy streaming) I can hear the router doing a greater slope electric buzzing/hissing noise is a little disconcerting... I'm not sure my brain fried by overclocked wifi will be worth a high speed in the end...: eek:

• DVRW firmware update killed

  I have acquired a used model m7790y Pavilion Media PC with some problems.

  The original owner had not created the recovery disks. I was initially unable to succeed in their creation, so I ran to the recovery of the recovery partition, using the start option. That's happened. I could eventually create the recovery (on 2 discs DVD + R) media. If the drive worked there at that time.

  After that, I have treated all updates Vista SP1 til. Then, I have treated several updates HP found in the x 32 area of Vista software and driver download for the system, including an updated firmware for the optical drive from TSST. Then, I treated all other Vista updates thru SP2 and beyond. I thought that everything was fine but then I tried to open the optical drive and it did not. Then I noticed that a light shone from the reader. Windows does not currently show a DVD player device, but because of BIOS. It shows in the BIOS as the 3rd drive: TSSTcorpCD/DVD. The update of the firmware, I treated is sp35094.exe and has been marked as TSST TS-H653L DVD-R/RW Drive Firmware Update Version 0714.

  I have redownloaded update and tried to re - run. It fails, saying that the system does not have the minimum requirements for the update. As the drive is not listed in the Device Manager, maybe it's to be expected. I don't think that it produced an error the first time. Both times I ran from within Windows Explorer.

  Is it possible to fix this drive or is it now a brick?

  The device is seven years old. It's a brick.

  Replace the DVD burner with a new DVD of SATA burner. They are pretty cheap these days and about $20.00.

• Seagate Hard Drive Firmware Update for the drive model: ST1000LM024

  I have (HP Pavilion dv6-7180se Entertainment Notebook PC). All the drivers for this model installed correctly except the drivers Frimware (Seagate hard drive Firmware Update) and (PLDS Optical Drive Firmware Update). the first one says "this hard drive model is not supported. Model = ST1000LM024"but my hard drive came from the factory, so what is the practice solution to install this driver? images .view of problems:

  This is to seagate:

  and for PLDS:

  Need help. Thank you.

  What mean of these messages, is that these "Firmware updates" do not apply to material in your specific computer. The two "Seagate Firmware Updates" are respectively for the hard drives of 250 GB / 320 GB and 500/750 GB hard drives. Your computer comes with a 1 TB hard drive, which is not subject to updates of the firmware. The "PLDS Optical Drive Update" is for another drive to CD/DVD only installed in your computer and also does not apply. There is no further action to take... Do not attempt to install these updates of firmware, because they do not apply to the hardware in your computer.

  If you have any other questions, feel free to ask.

  Please click the 'Thumbs Up' white LAURELS to show your appreciation

• E260 keeps restarting, firmware update does not help

  Hey everybody

  So I'm trying to fix my Sansa e260 friends and I'll get in trouble. When you turn it on, it just continuously restarts itself, I've included a video of what he does. http://Tinypic.com/r/2wq78jp/6

  I have already searched through this forum and tried the firmware update, after the update exactly the same thing just keep to themselves. I don't know where to go from here, any help would be appreciated. Thank you!

  Formatting the device using the Recovery Mode.  This erases all the materials for the device, but it's locked up in any case.

  For this procedure, first of all we have this word from our sponsor:

  In Recovery Mode, do not USE NOT THE COMMAND FORMAT WINDOWS ON THE PARTITION RESERVED.  Use the trick of ONLY sansa.fmt folder!

  Well, here are the steps (features of version 1 only):

  • Start with your OFF e200.
  • Slide the HOLD switch to the right (orange list).
  • Open a Windows Explorer on your PC.  Use my computer or [Windows key] + E.
  • Press and hold the REC button on your e200 while plugging in the USB cable.
  • The Sansa will specify "Welcome to Recovery Mode, type MSD."
  • On the PC, you will see a new device labeled 16 MB FORMAT.
  • Double-click this icon to open the reserved partition.  Yet once, DO NOT format using the available Windows command!
  • Right-click in this partition and select new folder.
  • Rename it sansa.fmt folder and you're ready!
  • With the help of remove it safely function (icon at the bottom of your screen in the taskbar), eject the Sansa.
  • Slide the HOLD switch to the left.
  • Try turning your restored e200 once she gets in shape automatically.

  Let us know how it goes!

  Bob

• Firmware Updater problems :(

  I just download the Sansa firmware update, and when I go to run it, an error message appears saying "the Installation failed. Please try again later. "I started again and received the same error message. Then I waited about 30 min. and sure enough, same error message. What I'm doing wrong!

  OK, the fact is that 90% of us who have been here very long you will simply ignore the update. On the "rocket", go to settings > system settings > Info and watch the number of Firmware if it starts V01 access the Thread called Fuze Firmware Updater, in the first post to find the update of the firmware that starts V01 and then follow the instructions on this post. If your Firmware number starts V02 find this firmware and follow the instructions.