First management LAN CiscoWorks LMS or Cisco? Help

Similar Questions

• CiscoWorks LMS 4.0.1 and 3850 switch support

  HI, I want to know if the 3850 switch is supported in ciscoworks LMS 4.0.1 I added devices, successful inventory collections but peripheral icon is blue with question mark '? ' and config sync always fails.

  I tried to download the packages to install it, but I couldn't find it.

  Thanks help fo

  3850 is supported on LMS 4.2.3. Check the list supported here:

  http://www.Cisco.com/en/us/docs/net_mgmt/ciscoworks_lan_management_solution/4.2.3/device_support/table/lms423sdt.html

  You must upgrade to 4.2.3 LMS or 1.3 FT go.

  -Thank you

  Vinod

  *Side encourages contributors and it's really free. **

• My Fire Fox download video in support not detected on you tube. It is always shows only the first video that i was downloaded.pls help

  My Fire Fox download video in support not detected on you tube. It is always shows only the first video that i was downloaded.pls help

  I don't think there is much you can do about it outside the use of workaround to reload the page until this problem is corrected.

  There is this bug on this problem:

  • http://Bugzilla.DownloadHelper.NET:8080 / show_bug.cgi? id = 642

  I don't know if other extensions download suffer from this issue, as well, so you can try a little more try the website of the add-on and if possible use a different format like WebM, if they are available.

  Also note that not all videos are downloaded and registered correctly. Some may have a size of 0 bytes and fail to download, so, best is to check in downloads of the toolbar Manager in the drop-down list to make sure that the file size is correct (i.e. neither 0 bytes, but a more likely size).

  YouTube streaming makes changes to the code and the way its web pages work, so extensions can fail at any time.

• CiscoWorks LMS 4.1 monitor temperature

  Hello everyone!

  I am creating a poller to monitor the trap of the temperature of my cisco catalyst 2960 Ciscoworks LMS 4.1.

  I created a snmp trap on my device:

  Switch(conf-t) # snmp-server <@IP_server_LMS>SNMPv2c host -I use SNMPv2c

  Switch(conf-t) # Server enable snmp traps envmon temperature

  I created a MIB model Envmon with these variables:

  -ciscoEnvMonTemperatureThreshold

  -ciscoEnvMonTemperatureStatusValue

  -ciscoEnvMonTemperatureState

  -ciscoEnvMonTemperatureLastShutdown

  I created a poller associated with my model, I add my device and when I click on 'Next', I have this error message:

  ###

  No instance are in the devices. This could be because the device is inaccessible, the device does not have the case for selected models or the timeout value is low.

  ###

  Could someone explain to me why I can't monitor MIB?

  Thanks for your consideration and Merry Christmas to all!

  It seems that most of the 2960 have a temperature sensor implemented in hardware and therefore, it shows no values.

  If a device does not show anything on CLI, it is almost impossible that it will display something via SNMP.

  -Thank you

• Management Center of firepower of Cisco on the stand-alone server

  You can install a management center of firepower of Cisco on a stand-alone server and not a virtual machine?  Here is a guide for the virtual machine:

  http://www.Cisco.com/c/en/us/TD/docs/security/firepower/60/Quick_Start/m...

  but I couldn't find one for a stand-alone server. Or what I can use this procedure for a stand-alone server.

  Looks like the only option of will not not with a virtual machine is to get the device itself.

  Thank you

  To install on a server bare metal, you could first put ESXi (free version) on it and then run FMC as the virtual machine only on that. I've had clients do this and it works fine.

• Remote control stop scrolling left and right while he needed video first put in pause and scroll any help?

  Remote control stop scrolling left and right while he needed video first put in pause and scroll any help?

  It was an update designed by tvOS 9.2 to the user of the address which have been accidentally scouring...

  http://www.CultofMac.com/420160/scrub-through-video-on-Apple-TV-in-TVos-9-2/

• URGENT::opening multiple files - i have 3 files in my directory... When I run the code I can open a file and read it... but the while loop get blocked after the first iteration... can someone me help or give some indications

  bbmChatDB of public database;

  public static FileConnection fconnRead = null;
  public static String fileReadData = "";
  public static InputStream is = null;
  data Byte [] = null;
  DataInputStream is = null;

  Here is my code...

  I have 3 files in my directory... When I run the code I can open a file and read it... but the while loop get blocked after the first iteration... can someone me help or give some indications

  try {}

  FileConnection fc = Connector.open("file:///store/home/user/documents/BSM/") (FileConnection); "

  If (fc.exists ()) {}

  Enumeration e = fc.list ();

  While (e.hasMoreElements ()) {}

  System.out.println ("files are:" + (String) e.nextElement ());

  play this file
  StringBuffer stringBuff = new StringBuffer();
  try {}
  System.out.println ("opening file")-;
  System.out.println ("file name is:" + (String) e.nextElement ());
  fconnRead = Connector.open("file:///store/home/user/documents/BSM/(String)e.nextElement(),Connector.READ_WRITE) (FileConnection);
  System.out.println ("data length")-;
  If (fconnRead.exists ()) {}
  is = fconnRead.openDataInputStream ();
  data = IOUtilities.streamToBytes (is);
  Ddd = new String string (data);
  fileReadData = ddd.toString ();
  System.out.println ("length of data:" + fileReadData.length ());
  System.out.println ("read data :" + fileReadData);

  }

  } catch (IOException ee) {}
  ee.printStackTrace ();
  System.out.println ("Exception in the read data :")
  + ee.getMessage ());
  }

  }
  }

  } catch (IOException e) {}

  e.printStackTrace ();
  }

  {Finally

  try {}
  If (is! = null) {}
  is. Close();
  }
  System.out.println ("is closed...");
  } catch (IOException e1) {}

  E1. PrintStackTrace();
  }

  If (fconnRead! = null) {}
  try {}
  fconnRead.close ();
  } catch (Exception e) {}
  System.out.println (try ());
  }

  }

  }

  You can recode this treatment so that it uses only:

  e.nextElement ())

  Once a loop iteration.

  Directly at the start saying something like:

  String fileName = e.nextElement ());

  and use fileName everywhere in your loop.

  Also be aware that printStackTrace() will do nothing in your situation, it only works if you catch Throwable.  So make sure you something output all your catches exception and also have a catch (Throwable t) to catch the things you miss, as follows:

  {} catch (Throwable t)

  t.printStackTrace ();

  System.out.println ("Eception exception:" + t.toString ());

  }

  I think your code is thrown an exception and you don't see it.

• CiscoWorks LMS 3.2 exporting bulk Configuration

  Hello

  Does anyone know an easy way to bulk export configurations off Ciscoworks LMS 3.2?  The only thing I found is the cli command export config u cwcli.exe - p-unit %, but it exports in XML format which is not very readable.  Prefer a text file format.  Someone at - it suggestions?

  Thank you

  Brian

  Hi Brian,.

  CLI, it is the only option, but what you can do to get the files in TEXT format is, you can connect to the server and

  go to this site: NMSROOT\CSCOpx\files\rme\dcma\shadow

  and

  NMSROOT\CSCOpx\files\rme\dcma\devfiles

  Thank you-

  Alya

  * Sides encourage contributors *.

• My video card does not appear in Device Manager... it's a HELP of PNY (GeForce FX5700 VEDDR 256MBAGP GF5700VA8D25D)! DRIVER NEEDED?

  My video card does not appear in Device Manager... it's a HELP of PNY (GeForce FX5700 VEDDR 256MBAGP GF5700VA8D25D)! DRIVER NEEDED?

  -The 'legacy' drivers are not technically a restore because there was
  never a movement forward to Win7.
  They are only a newer version and probably the last, the pilot who was provided for
  Some older cards on older (legacy) systems.

• Hello, I can not download first time cs6 remove too early. Help, please

  Hello, I can not download first time cs6 remove too early. Help, please

  Hi Leon92,

  Pleaase follow the steps mentioned in the KB: http://helpx.adobe.com/creative-cloud/kb/aam-lists-removed-apps-date.html and try to install again.

  You can also only the direct link: http://prodesigntools.com/adobe-cs6-direct-download-links.html .

  Please follow the very important instructions before downloading.

  Kind regards

  Romit Sinha

• Instalation Cisco's first Manager of licenses

  Hello

  What is the difference to install first Cisco Manager of licenses as standalone or living with one of the UC Applications.

  Concerning

  Leonardo Santana

  The difference of the ELM is impossible to install the application of the ISO CUCM, you must run ISO separate for the PLM and the rest is the same.

  Chris

• File ISO Bootable Cisco first Manager licenses 10.5

  Guys,

  I tried found Installation ISO for premium Cisco License Manager, deployed in a brand new installation of 10.x responsible for Cisco's Communication. The virtual machine will be independent PLM, I read the installation guide, downloaded the EGG file to deploy on the vCenter, but I couldn't find where is the file ISO of downloadable Installation of PLM, maybe I'm not looking for the correct download page site.

  Any help on this is appreciated.

  Thank you

  The ISO non-bootanle is here:

  https://software.Cisco.com/download/release.html?mdfid=286265616&flowid=... (2) & relind = & rellifecycle = & reltype = last

  You can convert not bootable to bootable with some searching in google.

  The ISO bootable must be requested through the tool SET.

• Cisco Collaboration first, Manager - fault reports

  Hi all

  Managed to install CEP 1.2 - change the layout is much better than previous versions.

  I added our MSE supervisor blade and I get the error below.

  

  Fault Board supervisor Power.

  However, when I go to the direct supervisor blade I see this.

  

  Don't you think CEP straightens this place incorrectly as the MSE is not followed by the plateau of power?

  If it's not it looks like I'll have to get a box connected with Cisco.

  See you soon

  Hi Dean

  What exact model of the MSE is and what version of the software you running on this subject?

  Thank you

  Rafal

• Problems with the closure, by opening the Task Manager and Norton Internet Security. Help, please!

  Hello

  I have a HP Pavilion dv7 with Windows Vista Home Premium (64-bit). Until Monday, there is no problem whatsoever with my computer at all. I have not installed or uninstalled, whatever it be, changed settings, done anything differently with my computer. Suddenly it now "hangs" on the screen of closing down. I'll try to reboot or stop using the menu start, and it will stay on this screen indefinitely. Now, I have to manually turn off the computer. I spent on the Support page and studied the Performance issues, and all I get is I have Visual settings that interfere with closing... except my Visual settings have not changed in any way. In addition, I can not properly update my computer or do a system restore because the computer will shut down.

  In addition, the Task Manager will appear no more. I'll press ctrl alt del and nothing appears, just the green icon in the corner of the screen. If I try to right click, no response.

  I tried to do a full system scan in Norton Internet Security but she "leaves" scanning. It will scan correctly when I'm in safe mode, but it comes with no virus, trojan or other problem.

  So in essence, I tried everything I can think of to fix my computer nothing works. It was working perfectly before this week. I have no idea where to go. Any thoughts?

  Thanks in advance,

  G

  Hello

   

   

  Method 1.
  First check to see if there are external devices attached to the computer, if so remove and check.

   

  Method 2.

  Step A.

  Start your computer in safe mode and check if it starts.

  Troubleshooting in safe mode
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshooting-problems-while-in-safe-mode

   

  Step B.

  If it starts on the desktop in safe mode and then set your computer to the clean boot and check if it starts successfully. If it starts successfully can be a third-party application or service is causing the problem. We can use the approach 50 / 50 to narrow down the root cause of the problem.

  
  See the article below for instructions on how to start your computer in a clean boot state.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135
  Note: When the diagnosis is complete, don't forget to reset your computer to normal startup. Follow step 7 in the above article.

   

   

  Method 3.
  I recommend to run the restore of the system in safe mode and check if it works very well.
  Reference:
  System Restore: frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows-Vista/system-restore-frequently-asked-questions
  Note: If you use system restore when the computer is in safe mode, you can not undo the restore operation. However, you can run System Restore again and choose a different restore point if any.

   

   

  I hope this helps.

   

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• How to reset the password on a Windows-based CiscoWorks LMS 3.2?

  I have problems with the procedure for recovery of password on a 3.2 CiscoWorks installation. The problem is that I have no idea what versions of software are running (track never cared).

  I tried following the steps here: http://www.cisco.com/en/US/products/sw/cscowork/ps2073/products_password_recovery09186a0080107dee.shtml (twice) and I was impossible to reset the password.

  Is there something that I am missing? Something extremely obvious I forgot?

  Thanks for any help!

  Use the resetpasswd utility:

  NMSROOT/bin/resetpasswd admin