First shot at the site to site VPN fails
This is my first attempt at establishing a VPN site-to site on ASA 5505 s. Fortunately, I'm able to do on the bench and not on the real sites. As soon as I can verify connectivity, I'll move them to the physical sites.
The two ASAs are running 8.3 (1). I tried with ASDM and I tried via CLI. I don't seem to be able to do anyway.
An ASA is configured with the address of WAN 10.1.52.1/24, address LAN 192.168.52.1. Another ASA is set up 10.1.200.1/24 WAN, LAN 192.168.200.1. Because they are on the bench (lab / whatever) there is a single cable connects the two WAN ports. I have a single workstation on each LAN to test connectivity. I CAN'T successfully ping the WAN ASA (10.1.52.1) from the workstation on 192.168.200.1 and vice versa. I'm NOT able to ping the workstation on 192.168.200.1 or of the ASA 10.1.200.1 (192.168.52.1) LAN and vice versa.
Here are the configs for the two and some recording of debug output:
ASA Version 8.3 (1)
!
MAIN host name
activate 8Ry2YjIyt7RRXU24 encrypted password
2KFQnbNIdI.2KYOU encrypted passwd
names of
!
interface Vlan1
nameif inside
security-level 100
192.168.200.1 IP address 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP 10.1.200.1 255.255.255.0
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
passive FTP mode
clock timezone CST - 6
network of the object inside
192.168.200.0 subnet 255.255.255.0
the CISC subject network
192.168.52.0 subnet 255.255.255.0
ICMP-type of object-group ICMP_ALLOWED
Description allow pings
echo ICMP-object
response to echo ICMP-object
ICMP-object has exceeded the time
Object-ICMP traceroute
ICMP-unreachable object
all permitted extended INCOMING icmp access list any object-group ICMP_ALLOWED Journal d
ebugging
VPN-2-CISC scope ip 192.168.52.0 access list allow 255.255.255.0 192.168.200
.0 255.255.255.0 debug log
VPN-2-CISC extended access list allow icmp 192.168.52.0 255.255.255.0 192.168.2
00,0% 255.255.255.0
outside_cryptomap_1 list extended access allowed object CISC object INSIDE Journal ip
debugging
pager lines 24
Enable logging
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
no failover
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
NAT (inside, outside) static source inside inside static destination CATC-CATC
!
network of the object inside
NAT dynamic interface (indoor, outdoor)
Access-group ENTERING into the interface outside
Route outside 0.0.0.0 0.0.0.0 10.1.52.1 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
Enable http server
http 192.168.1.0 255.255.255.0 inside
http 192.168.200.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
VPN-2-CATC 1 crypto card matches the address outside_cryptomap_1
card crypto VPN-2-CATC 1 set pfs
card crypto VPN-2-CATC 1 set peer 10.1.52.1
card crypto VPN-2-CATC 1 set transform-set ESP-3DES-MD5
crypto VPN-2-CISC outdoors card interface
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
md5 hash
Group 2
life 86400
Telnet 0.0.0.0 0.0.0.0 inside
Telnet timeout 10
SSH timeout 5
Console timeout 0
dhcpd outside auto_config
!
dhcpd address 192.168.200.5 - 192.168.200.99 inside
dhcpd allow inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
attributes of Group Policy DfltGrpPolicy
value of filter-VPN VPN-2-CISC
tunnel-group 10.1.52.1 type ipsec-l2l
IPSec-attributes tunnel-group 10.1.52.1
pre-shared-key VPN2VPN
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname
Cryptochecksum:53060156da27a8404adc45a01ff7324a
: end
==================
ASA Version 8.3 (1)
!
CISC hostname
activate 8Ry2YjIyt7RRXU24 encrypted password
2KFQnbNIdI.2KYOU encrypted passwd
names of
!
interface Vlan1
nameif inside
security-level 100
192.168.52.1 IP address 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP 10.1.52.1 255.255.255.0
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
passive FTP mode
network of the object inside
192.168.52.0 subnet 255.255.255.0
network of the PRINCIPAL object
192.168.200.0 subnet 255.255.255.0
ICMP-type of object-group ICMP_ALLOWED
pings Allow Description of the tests
echo ICMP-object
ICMP-object has exceeded the time
Object-ICMP traceroute
ICMP-unreachable object
response to echo ICMP-object
extended permitted INBOUND icmp access list any any ICMP_ALLOWED object-group
VPN_TO_MAIN to access extended list ip 192.168.200.0 allow 255.255.255.0 192.168.52.0 255.255.255.0
VPN_TO_MAIN list extended access allow icmp 192.168.200.0 255.255.255.0 192.168.52.0 255.255.255.0
outside_cryptomap_1 list of allowed ip extended access PRINCIPAL inside object
pager lines 24
Enable logging
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
no failover
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
NAT (inside, outside) static source inside MAIN destination inside static
!
network of the object inside
NAT dynamic interface (indoor, outdoor)
Access-group ENTERING into the interface outside
Route outside 0.0.0.0 0.0.0.0 10.1.200.1 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
Enable http server
http 192.168.52.0 255.255.255.0 inside
http 192.168.200.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
card crypto VPN_TO_MAIN 1 corresponds to the address outside_cryptomap_1
card crypto VPN_TO_MAIN 1 set pfs
card crypto VPN_TO_MAIN 1 set peer 10.1.200.1
VPN_TO_MAIN 1 transform-set ESP-3DES-MD5 crypto card game
VPN_TO_MAIN interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
md5 hash
Group 2
life 86400
Telnet 0.0.0.0 0.0.0.0 inside
Telnet timeout 10
SSH timeout 5
Console timeout 0
dhcpd outside auto_config
!
dhcpd address 192.168.52.5 - 192.168.52.99 inside
dhcpd allow inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
attributes of Group Policy DfltGrpPolicy
value of VPN-filter VPN_TO_MAIN
tunnel-group 10.1.200.1 type ipsec-l2l
IPSec-attributes tunnel-group 10.1.200.1
pre-shared-key VPN2VPN
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname
Cryptochecksum:fb0bfb4b67a8bfb2360a0d4499ce7f3d
: end
don't allow no asdm history
===================
When I try to ping from the internal network of CATC, 192.168.52.0/24 to the interface internal ASA HAND 192.168.200.1, I get...
Built of outbound ICMP connection for faddr gaddr laddr 192.168.52.7/1 192.168.52.7/1 192.168.200.1/0
Connection of disassembly for faddr gaddr laddr 192.168.52.7/1 192.168.52.7/1 192.168.200.1/0 ICMP
Built of incoming UDP connection, 6669 for inside:192.168.52.7/68 (192.168.52.7/68) at identity:255.255.255.255/67 (255.255.255.255/67)
---
I also try to hit a web server address: 192.168.200.5
Built of outgoing TCP connection 6674 for outside:192.168.200.5/80 (192.168.200.5/80) at inside:192.168.52.7/50956 (192.168.52.7/50956)
TCP connection of disassembly 6674 for outside:192.168.200.5/80 to inside:192.168.52.7/50956 duration 0:00:30 bytes 0 SYN Timeout
Deny tcp src outside:192.168.200.5/1632 dst inside:192.168.52.7/80 by access-group "IN" [0 x 0 0 x 0]
I don't get denied due to the INBOUND access-group. I thought with a VPN, the traffic bypasses standard access rules.
No show session upwards in the ASDM followed of > window VPN.
View ipsec his AND show isakmp its also well translate by "there are no ipsec/isakmp sas.
In addition,
In the constituencies of P2: 1997
In P2 invalid Exchange: 0
In P2 Exchange rejects: 1997
Requests for removal in his P2: 0
Exchanges of P2: 360
The Invalides Exchange P2: 0
Exchange of P2 rejects: 0
Requests to remove on P2 Sa: 360
=========================
I would like to eventually run the occasional http via this VPN traffic, but it will primarily serve to connect our two IP phone systems
Thank you all,
Laner
Hi Laner,
I created a configuration depending on your configuration: Please see the newsletter:
SITE 1
crypto ISAKMP policy 10
preshared authentication
3des encryption
md5 hash
Group 2
life 86400
tunnel-group 10.1.52.1 type ipsec-l2l
IPSec-attributes tunnel-group 10.1.52.1
pre-shared-key VPN2VPN
network of the object inside
192.168.200.0 subnet 255.255.255.0
the CISC subject network
192.168.52.0 subnet 255.255.255.0
outside_cryptomap_1 extended access list permit ip object INSIDE object CISC
NAT (inside, outside) static source inside static destination CATC-CATC No.-PROXY-ARP ROUTE-LOOK inside
VPN-2-CATC 1 crypto card matches the address outside_cryptomap_1
card crypto VPN-2-CATC 1 set pfs
card crypto VPN-2-CATC 1 set peer 10.1.52.1
card crypto VPN-2-CATC 1 set transform-set ESP-3DES-MD5
This configuration is not necessary because you specify IP as the Protocol and it will allow all through the tunnel
VPN-2-CISC scope ip 192.168.52.0 access list allow 255.255.255.0 192.168.200.0 255.255.255.0
attributes of Group Policy DfltGrpPolicy
value of filter-VPN VPN-2-CISC
//
SITE 2
crypto ISAKMP policy 10
preshared authentication
3des encryption
md5 hash
Group 2
life 86400
tunnel-group 10.1.200.1 type ipsec-l2l
IPSec-attributes tunnel-group 10.1.200.1
pre-shared-key VPN2VPN
network of the object inside
192.168.52.0 subnet 255.255.255.0
network of the PRINCIPAL object
192.168.200.0 subnet 255.255.255.0
outside_cryptomap_1 list extended access permitted ip object INSIDE PRINCIPAL object
NAT (inside, outside) static source inside MAIN destination inside static route no-proxy-arp-search
card crypto VPN_TO_MAIN 1 corresponds to the address outside_cryptomap_1
card crypto VPN_TO_MAIN 1 set pfs
card crypto VPN_TO_MAIN 1 set peer 10.1.200.1
VPN_TO_MAIN 1 transform-set ESP-3DES-MD5 crypto card game
This configuration is not necessary because you specify IP as the Protocol and it will allow all through the tunnel
VPN_TO_MAIN to access extended list ip 192.168.200.0 allow 255.255.255.0 192.168.52.0 255.255.255.0
VPN_TO_MAIN list extended access allow icmp 192.168.200.0 255.255.255.0 192.168.52.0 255.255.255.0
attributes of Group Policy DfltGrpPolicy
value of VPN-filter VPN_TO_MAIN
//
Match your configuration with my setup and make changes. Filters VPN are not allowed because you are not filtering anything. Remove the filter VPN at both ends, and then try to ping through the VPN. Also if you ping forms inside the interface inside the interface of the other device, and then make sure that access management is enabled on both interfaces, it will not respond to ping requests.
How to check if access to administration are enabled or not is by running the command:
See the human race
If you get anything enter command 'inside man' and then run ping.
Let me know if it helps.
Vishnu
Tags: Cisco Security
Similar Questions
-
Help the Site VPN Site PIX 501
Hello
I'm pretty new to PIX firewall, so I hope someone here can help me.
I have two PIX and try to create a private network virtual between the two PIX. I posted the configs below.
The problem is that I can ping PIX on a PIX two, but I can't ping the servers behind TWO PIX. On two PIX, I cannot ping PIX ONE or all the servers behind it.
Any advice would be appreciated.
Thank you
PIX 1
6.2 (2) version PIX
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
hostname TMAXWALES
domain ciscopix.com
fixup protocol ftp 21
fixup protocol http 80
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol they 389
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol sip 5060
fixup protocol 2000 skinny
names of
inside_outbound_nat0_acl ip 192.168.254.0 access list allow 255.255.255.0 192.1
68.1.0 255.255.255.0
outside_cryptomap_20 ip 192.168.254.0 access list allow 255.255.255.0 192.168.1
.0 255.255.255.0
pager lines 24
interface ethernet0 10baset
interface ethernet1 10full
Outside 1500 MTU
Within 1500 MTU
IP address outside of *. *.198.139 255.255.255.248
IP address inside 192.168.254.1 255.255.255.0
alarm action IP verification of information
alarm action attack IP audit
location of PDM 192.168.254.10 255.255.255.255 inside
location of PDM 192.168.1.0 255.255.255.0 outside
history of PDM activate
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_outbound_nat0_acl
NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
Route outside 0.0.0.0 0.0.0.0 *. * 1.198.137
Timeout xlate 03:00
Timeout conn 0 half-closed 01:00:10: 00 udp 0:02:00 CPP 0: h323 from 10:00 0:05:00 TR
p 0:30:00 sip_media 0:02:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
RADIUS Protocol RADIUS AAA server
AAA-server local LOCAL Protocol
Enable http server
http 192.168.254.10 255.255.255.255 inside
No snmp server location
No snmp Server contact
SNMP-Server Community public
No trap to activate snmp Server
enable floodguard
Permitted connection ipsec sysopt
No sysopt route dnat
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
outside_map 20 ipsec-isakmp crypto map
card crypto outside_map 20 match address outside_cryptomap_20
card crypto outside_map 20 peers set *. *.198.138
outside_map crypto 20 card value transform-set ESP-3DES-SHA
outside_map interface card crypto outside
ISAKMP allows outside
ISAKMP key * address *. *.198.138 netmask 255.255.255.255 No.-xauth non - co
Nfig-mode
part of pre authentication ISAKMP policy 20
ISAKMP policy 20 3des encryption
ISAKMP policy 20 chopping sha
20 2 ISAKMP policy group
ISAKMP duration strategy of life 20 86400
Telnet timeout 5
SSH timeout 5
Terminal width 80
PIX 2
6.2 (2) version PIX
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
hostname tmaxbangor
domain ciscopix.com
fixup protocol ftp 21
fixup protocol http 80
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol they 389
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol sip 5060
fixup protocol 2000 skinny
names of
permit 192.168.1.0 ip access list inside_outbound_nat0_acl 255.255.255.0 192.168
. 254.0 255.255.255.0
permit 192.168.1.0 ip access list outside_cryptomap_20 255.255.255.0 192.168.254
.0 255.255.255.0
pager lines 24
opening of session
debug logging in buffered memory
interface ethernet0 10baset
interface ethernet1 10full
Outside 1500 MTU
Within 1500 MTU
IP address outside of *. *.198.138 255.255.255.248
IP address inside 192.168.1.1 255.255.255.0
IP verify reverse path to the outside interface
IP verify reverse path inside interface
the IP audit info action alarm reset drop
reset the IP audit attack alarm drop action
location of PDM 192.168.1.0 255.255.255.0 inside
PDM logging 100 information
history of PDM activate
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_outbound_nat0_acl
NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
Route outside 0.0.0.0 0.0.0.0 *. * 1.198.137
Timeout xlate 03:00
Timeout conn 0 half-closed 01:00:10: 00 udp 0:02:00 CPP 0: h323 from 10:00 0:05:00 TR
p 0:30:00 sip_media 0:02:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
RADIUS Protocol RADIUS AAA server
AAA-server local LOCAL Protocol
Enable http server
http 192.168.1.0 255.255.255.0 inside
http 192.84.7.111 255.255.255.255 inside
http 192.168.1.10 255.255.255.255 inside
No snmp server location
No snmp Server contact
SNMP-Server Community public
No trap to activate snmp Server
enable floodguard
Permitted connection ipsec sysopt
No sysopt route dnat
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
outside_map 20 ipsec-isakmp crypto map
card crypto outside_map 20 match address outside_cryptomap_20
card crypto outside_map 20 peers set *. *.198.139
outside_map crypto 20 card value transform-set ESP-3DES-SHA
outside_map interface card crypto outside
ISAKMP allows outside
ISAKMP key * address *. *.198.139 netmask 255.255.255.255 No.-xauth non - co
Nfig-mode
part of pre authentication ISAKMP policy 20
ISAKMP policy 20 3des encryption
ISAKMP policy 20 chopping sha
20 2 ISAKMP policy group
ISAKMP duration strategy of life 20 86400
Telnet 192.168.1.0 255.255.255.0 inside
Telnet timeout 50
SSH timeout 5
Terminal width 80
Can't see anything obviously wrong with the configs. You have these connected back to back on the same subnet, it looks that it even if you have xxx out IP addresses? If so it's maybe a routing problem, in what they send everything to the default gateway of xxx.x.198.137 rather than to the other.
Try to add a static route to the remote subnet to each PIX that points directly to the peer, so on PIX1 you should have:
Route outside 192.168.1.0 255.255.255.0 xxx.x.198.138
and on PIX2 do:
Route outside 192.168.254.0 255.255.255.0 xxx.x.198.139
and see if that makes a difference. Note that you wouldn't encounter this problem when these two PIX is on separate networks and uses the default gateway for all routing decisions.
If this still fails, run 'debug cryp isa' and ' debug cry ipsec "on the two PIX are trying to build a tunnel again, and then and send us the output.
Also, make sure your tests that you're rattling to a host behind a PIX to a host behind the other PIX, ping PIX to PIX or host because of PIX that won't test your VPN connection.
-
Due to a series of problems with my computer old (now), I uninstalled Adobe Photoshop and Premiere Elements, after carefully printed on the profile and serial numbers. Now, after buying a Windows 10 HP desktop, I tried to install a very valuable software. From the beginning of the installation, I entered the serial number - as - my print-out. He refused and I was asked to enter again! Checked and re-checked-exactly as I had entered it. But the refusal of those same numbers have persisted.
Logging into my account - after the link printed for the serial number of the product (https://www.adobe.com/go/acctmgmtserialnum) has failed to implement a destination in my browser - I see that there is mention of maintenance — although the denial of my serial number was not this as a problem, rather simply accepting the number. Under my products, I drew the caveat that the information could not be provided.
I learned that a forum - an area in which I never dared before - is my ONLY option. Even though I remember receiving a lot of emails about CC - I was very happy with my existing Photoshop and still haven't use iCloud.
As a 'beginner' complete in this way to get an answer, please help.
Photoshop has been replaced and now to keep my software being installed as redundant? Is it simply the maintenance being undertaken - and the rejection of serial number simply a warning "generic"? -Thank you in advance - for any help you can afford me.
I was not yet looking for Adobe Premiere Elements - waiting for the same print to attract the same rejection of the number.
You MAY have just run into a case of an old program that will not properly install on a new operating system
Windows 10 is not really compatible with your version 9
An idea that MAY work to install or run some programs in Windows 10 old... works for some, not for others
-The icon of the program or EXE file RIGHT click and select a compatibility mode in the pop-up option
- or run as Administrator http://forums.adobe.com/thread/969395 to assign permissions Windows COMPLETE can help... said yet, but sometimes it is necessary for all Adobe programs (this is same as using an administrator account)
-
Hello, thanks for any help in advance, my last page of the site (webmaster) load everything first.
The site map is in order, can't find any info on how to change this?
Help, please!
If you want to see what it is located in the: http://cedargrovestable.businesscatalyst.com/contact.html
Thank you.
Hello
The site load very well home page: http://cedargrovestable.businesscatalyst.com/
If you will see the url of the page then will come, contact page: http://cedargrovestable.businesscatalyst.com/contact.html
Thank you
Sanjit
-
T410 - UltraNav 15.1.19 - Alt + Tab hook the first shot.
I notice that just after I use Alt - Tab to switch to windows, usually my first shot on the touchpad does not work.
It's frustrating, because I do Alt - Tab all the time.
Any fix for that?
change the topic that corresponds to the discussion.
Hi James,
I started to write a response and he would say that, after my keyboard had been replaced (twice was the charm) and all the parameters check Smart unchecked, it's the outstanding issue.
So I was wondering if I indeed uncheck all smart control parameters. It's when I fiddled with the only, I can not turn off... PalmCheck.
Voila! If I put PalmCheck at the minimum or near minimum, I do not experience this problem. However, I believe that the setting is near the maximum.
I tested a lot for Lenovo, I should be on its payroll :-) I think that Lenovo really needs to do a lot more testing before deployment of its products. Especially with all these questions of input device, as I thought (before I got my ThinkPad) was supposed to be the highlight of the ThinkPad. It turns out, due to various problems (defective material, bad drivers, bad settings), I have never had a worse experience with input devices in all my years of owning computers. It is a fact, not an exaggeration...
At least I got finally including this one :-)
-
You try to run a Site to site VPN and remote VPN from the same IP remotely
We currently have a site to site VPN configuration between our offices call center and a 3rd party that allows them to access our training to their employees to use environment while being trained on our systems. This tunnel is running between our ASA and their ASA without problem; However, when we have managers come out to the call center, they are unable to use remote VPN to access our office.
Apparently the same IP peer remote that we use for our site to the other tunnel is the same IP that our managers use to access the internet when they are on-site with the customer. When I look at the logs it shows the VPN attempt and then I get treatment Information Exchange has failed. So from what I can understand when our managers are trying to connect to our firewall from the same IP address as the counterpart of site to site it automatically tries to create a tunnel, according to the information of the site to the other tunnel. If our managers are anywhere else, they can connect through remote VPN with no problems.
My question is if anyone knows of a way to make the firewall allow VPN site to site and remote connections with the same remote IP address.
Hi John,.
Basically, in older versions, when you hit a static encryption card and you does not match this static encryption completely map the connection continues until the dynamic encryption card. For this reason, you can connect your IPSec clients before. A bug has been opened on this vulnerability.
CSCuc75090 Details of bug
The crypto IPSec Security Association are created by dynamic crypto map to static peers
Symptom:
When a static VPN peer adds all traffic to the ACL crypto, a surveillance society is based even if the pair IP is not allowed in the acl to the main façade encryption. Are these SA finally put in correspondence and commissioning the dynamic crypto map instance.
Conditions:
It was a planned design since the first day that allowed customers to fall through in the case of static crypto map did not provide a necessary cryptographic services.
The SA must be made from a peer configured statically and a dynamic crypto map instance must be configured on the receiving end.
Workaround solution:
N/A
Some possible workarounds are:
Configure a static nat device when you try to use the remote VPN if the firewall remotely will be hit with a different public IP address. It would be a good solution, but it will depend on how many ip addresses public you have available, if you really want one of these ip addresses for that access.
Also, I thought you could use AnyConnect instead of the IPSec VPN client. I don't know how many users need to connect from your PC to the remote site, but the ASA has 2 licenses SSL available that you could use. Because Anyconnect uses the SSL protocol, it won't have a problem on your environment.
Below some information:
Hope this helps,
Luis.
-
Site to Site VPN, endpoint of the traffic on the loopback and ping down alternative packages
Hi team,
This is my first discussion. Today, I came across a new senario where in I was able to establish the tunnel vpn site-to-site between two sites. To my amazement, I am able to successfully ping to the router (Site A) to the server without drops keeping source as fa 0/1 (172.25.170.1) However, LAN segment (host) alternate packages are declining while reaching the server. Please find the picture below:
R2 - is ISP
We are required to use private segment WAN ip addresses so we have no choice other than to keep the public ip address on the loopback. To create the site to site, I asked the card encryption on the fa outside interface 0/0 with ip 1.1.1.1. Then I used the command cypto card loopback 1 mount the tunnel and work address local VPN. I then set a route on the Site1 for fa of government local traffic 0/0 to insert the interesting traffice enter the map encryption.
Now everything works well to router server however I get replacement ping drops (50% success). I am not able to solve this problem. The result above is both real and gns.
Help, please
Think it's a bug in IOS, disable IP CEF, hen now this works, but it is only a workaround to make it work for real IOS update.
-
Hello
I'm trying to solve a problem with the VPN, and I hope that someone could give me a helping hand.
We have 3 offices, each with an ASA 5505 like the router/firewall, connected to a cable modem
(NC Office) <----IPSEC----->(office of PA) <----IPSEC----->(TC Office)
Internally, we have a full mesh VPN, so all offices can talk to each other directly.
I have people at home, by using remote access VPN into the Office of PA, and I need them to be able to connect to two other offices there.
I was able to run for the Office of CT, but I can't seem to work for the Office of the NC. (I want to say is, users can remote access VPN in the PA Office and access resources in the offices of the PA and CT, but they can't get the Office of NC).
Someone could take a look at these 2 configs and let me know if I'm missing something? I am newer to this, so some of these configs do not have better naming conventions, but I'm getting there
PA OFFICE
Output of the command: "show run".
: Saved
:
ASA Version 8.2 (5)
!
hostname WayneASAnames of
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.1.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP 70.91.18.205 255.255.255.252
!
passive FTP mode
clock timezone IS - 5
clock to summer time EDT recurring
DNS lookup field inside
DNS domain-lookup outside
DNS server-group DefaultDNS
75.75.75.75 server name
75.75.76.76 server name
domain 3gtms.com
permit same-security-traffic intra-interface
object-group Protocol TCPUDP
object-protocol udp
object-tcp protocol
inside_access_in of access allowed any ip an extended list
IPSec_Access to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.2.0 255.255.255.0
IPSec_Access to access extended list ip 192.168.10.0 allow 255.255.255.224 192.168.2.0 255.255.255.0
IPSec_Access to access extended list ip 192.168.10.0 allow 255.255.255.224 192.168.5.0 255.255.255.0
inside_nat0 to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.10.0 255.255.255.224
inside_nat0 to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.2.0 255.255.255.0
inside_nat0 to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.5.0 255.255.255.0
TunnelSplit1 list standard access allowed 192.168.10.0 255.255.255.224
TunnelSplit1 list standard access allowed 192.168.1.0 255.255.255.0
outside_1_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.2.0 255.255.255.0
outside_2_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.5.0 255.255.255.0
outside_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.5.0 255.255.255.0
RemoteTunnel_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0
RemoteTunnel_splitTunnelAcl_1 list standard access allowed 192.168.1.0 255.255.255.0
RemoteTunnel_splitTunnelAcl_1 list standard access allowed 192.168.2.0 255.255.255.0
RemoteTunnel_splitTunnelAcl_1 list standard access allowed 192.168.5.0 255.255.255.0
out_access_in list extended access udp allowed any SIP host 70.91.18.205 EQ
out_access_in list extended access permit tcp any host 70.91.18.205 eq 5000
out_access_in list extended access permits any udp host 70.91.18.205 range 9000-9049
out_access_in list extended access permit tcp any host 70.91.18.205 EQ SIP
out_access_in list extended access allowed object-group TCPUDP any host 70.91.18.205 eq 5090
out_access_in list extended access permit udp any host 70.91.18.205 eq 5000
Note to outside-nat0 access-list NAT0 for VPNPool to Remote Sites
outside-nat0 extended ip 192.168.10.0 access list allow 255.255.255.224 192.168.2.0 255.255.255.0
outside-nat0 extended ip 192.168.10.0 access list allow 255.255.255.224 192.168.5.0 255.255.255.0
pager lines 24
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU----IPSEC----->----IPSEC----->
IP mask 255.255.255.224 local pool VPNPool 192.168.10.1 - 192.168.10.30
no failover
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0
NAT (inside) 1 0.0.0.0 0.0.0.0
NAT (outside) 0-list of access outside-nat0
inside_access_in access to the interface inside group
Access-group out_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 70.91.18.206 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
the ssh LOCAL console AAA authentication
Enable http server
http 0.0.0.0 0.0.0.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set esp-3des esp-md5-hmac VPNTransformSet
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
card crypto IPSec_map 1 corresponds to the address IPSec_Access
card crypto IPSec_map 1 set peer 50.199.234.229
card crypto IPSec_map 1 the transform-set VPNTransformSet value
card crypto IPSec_map 2 corresponds to the address outside_2_cryptomap
card crypto IPSec_map 2 set pfs Group1
card crypto IPSec_map 2 set peer 98.101.139.210
card crypto IPSec_map 2 the transform-set VPNTransformSet value
card crypto IPSec_map 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
IPSec_map interface card crypto outside
card crypto outside_map 1 match address outside_1_cryptomap
peer set card crypto outside_map 1 50.199.234.229
crypto ISAKMP allow outside
crypto ISAKMP policy 1
preshared authentication
3des encryption
sha hash
Group 2
life 43200
Telnet 192.168.1.0 255.255.255.0 inside
Telnet timeout 5
SSH 0.0.0.0 0.0.0.0 inside
SSH timeout 60
Console timeout 0
management-access inside
dhcpd outside auto_config
!
dhcpd address 192.168.1.100 - 192.168.1.199 inside
dhcpd dns 75.75.75.75 75.75.76.76 interface inside
dhcpd allow inside
!a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal RemoteTunnel group strategy
attributes of Group Policy RemoteTunnel
value of server DNS 75.75.75.75 75.75.76.76
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list RemoteTunnel_splitTunnelAcl_1
dfavier vUA99P1dT3fvnDZy encrypted password username
username dfavier attributes
type of remote access service
rduske vu0Zdx0n3oZWFSaX encrypted password username
username rduske attributes
type of remote access service
eric 0vcSd5J/TLsFy7nU password user name encrypted privilege 15
lestofts URsSXKLozQMSeCBk username encrypted password
username lestofts attributes
type of remote access service
jpwiggins 3WyoRxmI6LZjGHZE encrypted password username
username jpwiggins attributes
type of remote access service
tomleonard cQXk0RJCBtxyzZ4K encrypted password username
username tomleonard attributes
type of remote access service
algobel 4AjIefFXCbu7.T9v encrypted password username
username algobel attributes
type of remote access service
type tunnel-group RemoteTunnel remote access
attributes global-tunnel-group RemoteTunnel
address pool VPNPool
Group Policy - by default-RemoteTunnel
IPSec-attributes tunnel-group RemoteTunnel
pre-shared key *.
tunnel-group 50.199.234.229 type ipsec-l2l
IPSec-attributes tunnel-group 50.199.234.229
pre-shared key *.
tunnel-group 98.101.139.210 type ipsec-l2l
IPSec-attributes tunnel-group 98.101.139.210
pre-shared key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect the icmp
inspect the pptp
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:6d1ffe8d570d467e1ea6fd60e9457ba1
: endCT OFFICE
Output of the command: "show run".
: Saved
:
ASA Version 8.2 (5)
!
hostname RaleighASA
activate the encrypted password of Ml95GJgphVRqpdJ7
2KFQnbNIdI.2KYOU encrypted passwd
names of
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
192.168.5.1 IP address 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP 98.101.139.210 255.0.0.0
!
passive FTP mode
clock timezone IS - 5
clock to summer time EDT recurring
DNS lookup field inside
DNS server-group DefaultDNS
Server name 24.25.5.60
Server name 24.25.5.61
permit same-security-traffic intra-interface
object-group Protocol TCPUDP
object-protocol udp
object-tcp protocol
Wayne_Access to access extended list ip 192.168.5.0 allow 255.255.255.0 192.168.1.0 255.255.255.0
Wayne_Access to access extended list ip 192.168.5.0 allow 255.255.255.0 192.168.10.0 255.255.255.0
Shelton_Access to access extended list ip 192.168.5.0 allow 255.255.255.0 192.168.2.0 255.255.255.0
out_access_in list extended access permit tcp any host 98.101.139.210 eq www
out_access_in list extended access permit tcp any host 98.101.139.210 eq ftp
out_access_in list extended access permit udp any host 98.101.139.210 eq tftp
out_access_in list extended access udp allowed any SIP host 98.101.139.210 EQ
out_access_in list extended access permit tcp any host 98.101.139.210 eq 5090
out_access_in list extended access permit tcp any host 98.101.139.210 eq 2001
out_access_in list extended access permit tcp any host 98.101.139.210 eq 5080
out_access_in list extended access permit tcp any host 98.101.139.210 eq ssh
out_access_in list extended access permit tcp any host 98.101.139.210 eq 81
out_access_in list extended access permit tcp any host 98.101.139.210 eq 56774
out_access_in list extended access permit tcp any host 98.101.139.210 eq 5000
out_access_in list extended access permit tcp any host 98.101.139.210 eq 902
out_access_in list extended access permit tcp any host 98.101.139.210 eq netbios-ssn
out_access_in list extended access permit tcp any host 98.101.139.210 eq 445
out_access_in list extended access permit tcp any host 98.101.139.210 eq https
out_access_in list extended access allowed object-group TCPUDP any host 98.101.139.210 eq 3389
out_access_in list extended access allowed object-group TCPUDP range guest 98.101.139.210 5480 5487
out_access_in list extended access permits any udp host 98.101.139.210 range 9000-9050
inside_nat0 to access extended list ip 192.168.5.0 allow 255.255.255.0 192.168.1.0 255.255.255.0
inside_nat0 to access extended list ip 192.168.5.0 allow 255.255.255.0 192.168.2.0 255.255.255.0
inside_nat0 to access extended list ip 192.168.5.0 allow 255.255.255.0 192.168.10.0 255.255.255.0
pager lines 24
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0
NAT (inside) 1 0.0.0.0 0.0.0.0Access-group out_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 98.101.139.209 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
the ssh LOCAL console AAA authentication
Enable http server
http 0.0.0.0 0.0.0.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-3des esp-md5-hmac WayneTransform
Crypto ipsec transform-set esp-3des esp-md5-hmac SheltonTransform
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
card crypto IPSec_map 1 corresponds to the address Wayne_Access
card crypto IPSec_map 1 set pfs Group1
card crypto IPSec_map 1 set peer 70.91.18.205
card crypto IPSec_map 1 the transform-set WayneTransform value
card crypto IPSec_map 2 corresponds to the address Shelton_Access
card crypto IPSec_map 2 set pfs Group1
card crypto IPSec_map 2 set peer 50.199.234.229
card crypto IPSec_map 2 the transform-set SheltonTransform value
IPSec_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 1
preshared authentication
3des encryption
sha hash
Group 2
life 43200
Telnet timeout 5
SSH 0.0.0.0 0.0.0.0 inside
SSH timeout 5
Console timeout 0
management-access inside
dhcpd outside auto_config
!
dhcpd address 192.168.5.100 - 192.168.5.199 inside
dhcpd dns 24.25.5.60 24.25.5.61 interface inside
dhcpd allow inside
!a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
eric 0vcSd5J/TLsFy7nU password user name encrypted privilege 15
tunnel-group 50.199.234.229 type ipsec-l2l
IPSec-attributes tunnel-group 50.199.234.229
pre-shared key *.
tunnel-group 70.91.18.205 type ipsec-l2l
IPSec-attributes tunnel-group 70.91.18.205
pre-shared key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect the icmp
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:3d770ba9647ffdc22b3637e1e5b9a955
: endHello
I might have found the problem.
To be honest, I'm a little tired and concentration is difficult, especially when access between multiple device configurations. So second pair of eyes is perhaps in order.
At the moment it seems to me that this configuration is the problem on the SITE of PA
IPSec_Access to access extended list ip 192.168.10.0 allow 255.255.255.224 192.168.5.0 255.255.255.0
This is an ACL that defines networks the and remote for a connection VPN L2L.
Now, when we look at what connection VPN L2L this belong we see the following
card crypto IPSec_map 1 corresponds to the address IPSec_Access
card crypto IPSec_map 1 set peer 50.199.234.229
card crypto IPSec_map 1 the transform-set VPNTransformSet value
Now, we see that the peer IP address is 50.199.234.229. Is what site this? The IP address of the CT Site that works correctly?
Now what that said the ACL line I mentioned more early basically is that when the 192.168.10.0 network 255.255.255.224 wants to connect to the network 192.168.5.0/24 should be sent to the CT Site. And of course, this should not be the case as we want traffic to go on the NC Site
Also worth noting is that on the SITE of the above connection is configured with the '1' priority so it gets first compared a connection. If the VPN L2L configurations were in different order then the VPN Client connection can actually work. But it's just something that I wanted to point out. The actual resolution of the problem, of course, is to detach the configuration which is the cause of the real problem in which ASA attempts to route traffic to a completely wrong place.
So can you remove this line ACL of the ASA of PA
No IPSec_Access access list extended ip 192.168.10.0 allow 255.255.255.224 192.168.5.0 255.255.255.0
Then, test the VPN Client connection NC SITE again.
Hope that this will finally be the solution
-Jouni
-
Unable to connect to the site Web SSL VPN with firewall zone configured
I recently updated my 2911 company and set up a firewall area. This is my first experience with this and I used Cisco Configuration Professional to build the configuration of the firewall first and then edited the names to make it readable by humans. The only problem I can't solve is to learn site Web SSL VPN from outside. I can navigate the website and connect without problem from the inside, and even if it was useful to verify that the Routing and the site work properly it is really not what I. I don't get anything on the syslog for drops because of the firewall server, or for any other reason but packet capture show that no response is received when you try to navigate to the outside Web site. I am currently using a customer VPN IPSEC solution until I can get this to work and have no problem with it. I have attached a sanitized with the included relevant lines configuration (deleted ~ 400 lines including logging, many inspections on the movement of the area to the area and the ipsec vpn, which I already mentioned). I searched anything about this problem and no one has no problem connecting to their Web site, just to get other features to work correctly. All thoughts are welcome.
See the security box
area to area
Members of Interfaces:
GigabitEthernet0/0.15
GigabitEthernet0/0.30
GigabitEthernet0/0.35
GigabitEthernet0/0.45
area outside zone
Members of Interfaces:
GigabitEthernet0/1
sslvpn area area
Members of Interfaces:
Virtual-Template1
SSLVPN-VIF0
I tried to change the composition of the area on the interface virtual-Template1 to the outside the area nothing helps.
See the pair area security
Name of the pair area SSLVPN - AUX-in
Source-Zone sslvpn-area-zone of Destination in the area
Service-SSLVPN-AUX-IN-POLICY
Name of the pair area IN SSLVPN
Source-Zone in the Destination zone sslvpn-zone
service-policy IN SSLVPN-POLICY
Name of the pair area SELF SSLVPN
Source-Zone sslvpn-area free-zone Destination schedule
Service-SELF-to-SSLVPN-POLICY
Zone-pair name IN-> AUTO
Source-Zone in the Destination zone auto
Service-IN-to-SELF-POLICY policy
Name of the pair IN-> IN box
In the Destination area source-Zone in the area
service-policy IN IN-POLICY
Zone-pair name SELF-> OUT
Source-Zone auto zone of Destination outside the area
Service-SELF-AUX-OUT-POLICY
Name of the pair OUT zone-> AUTO
Source-Zone out-area Destination-area auto
Service-OUT-to-SELF-POLICY
Zone-pair name IN-> OUT
Source-Zone in the Destination area outside zone
service-strategy ALLOW-ALL
The pair OUT zone name-> IN
Source-out-zone-time zone time Zone of Destination in the area
Service-OUT-to-IN-POLICY
Name of the pair area SSLVPN-to-SELF
Source-Zone-Zone of sslvpn-area auto
Service-SSLVPN-FOR-SELF-POLICY
I also tried to add a pair of area for the outside zone sslvpn-zone passing all traffic and it doesn't change anything.
The area of networks
G0/0.15
172.16.0.1 26
G0/0.30
172.16.0.65/26
G0/0.35
172.16.0.129/25
G0/0.45
172.18.0.1 28
Pool of SSL VPN
172.20.0.1 - 172.20.0.14
Latest Version of IOS:
Cisco IOS software, software C2900 (C2900-UNIVERSALK9-M), Version 15.0 (1) M10, RELEASE SOFTWARE (fc1)
Glad works now. Weird question, no doubt.
I guess that on the deployment guide said that the firewall will not support inspection of TCP to the free zone, however, class nested maps are used to accomplish this, to be completely honest, I think it's a mess and the best thing to do is action past to auto for the protocols that you want and then drop the rest.
Let us know if you have any other problems.
Mike
-
Cannot access the internal resources for VPN site-to-site
We have two ASA. We set up just VPN site-to-site. For some reason, we are not able to access internal resources at the main office of the remote office. Do you have any suggestions? Thank you.
as wu suggested, please first confirm that the tunnel is mounted correctly
"sh cry isa his '-> will tell u if the phase 1 is in place
"sh cry ips its '-> say if phase 2 is in place
now once they r upward, when you ping from site to site b
program in the site, you should see one and decaps site b for traffic from a to b and vice versa for return transportation
Now we have to see where it is a failure
could be tht package is coming up to the asa but not getting is not encrypted or that the package does not come to the asa itself
You can run tracer package to see if it's getting wrapped, or in other words hits vpn tunnel
It might be a nat problem, and sometimes if it is a new configuration probably ISP may have blocked the esp traffic in one direction or in the other direction
the best approach, that it is turn on "management of access to the inside" on the firewall and make a ping of source of asa
inside ping
-
As I said, from now on, every single site I will for the first time today, he says that he is not a trusted site and cannot be verified, should I move forward. Yes. This is a site with it. Then when I'm on the site, some sites like some fb games not be loading not completely. It gives me just written information on the left side and the game just never came up. Also Amazon charges, but when I go to my account, I get the same type of information on the left side page, as I do with the fb games. I tried to reinstall firefox and tried to reset but nothing. Given to zero has worked in the past. Oh, a game says fb I had t install flash, but when I try to make I get an error message saying: it cannot install it. Everything was fine until about 2 hours ago.
I hope this helps. I don't know how it happened as I didn't do but check the date on your calendar. Mine has been updated with 2001, for some reason any. Once I changed it to the correct date, it works now. I saw a message that said something had expired. The contract or something like that and then I remembered that, something with the date, once caused something like that.
So just put the wrong date in the fixed. Go figure.
-
Before that I only had to type "IMDb" and press enter and put me to the site immediately, but now all these links come first.
Or I used to type 'youtube' and after knocking entered, I was took directly to the homepage of youtube.
What can I do to make it like it was before, so it takes me directly to the site? Second, my Norton passwords and user names for all sites that have been stored in my 'Norton safe"does not appear in the browser. This will be available soon?
Try to define your topic: config entries for:
- Keyword.Enabled - > true
- Browser.Fixup.Alternate.Enabled-> true
- Browser.Fixup.Alternate.prefix-> www.
- Browser.Fixup.Alternate.suffix-> .com
and then restart your browser and try again supernatural imdb.
You must use 'supernatural imdb' rather than "supernatural imdb" because you want the domain before the page for research work best.
-
Site to site VPN, I need all internet traffic to exit the site.
I have 2 sites connected via a pair of SRX5308
A = 192.168.1.0/24
IP WAN = 1.1.1.1
B = 192.168.2.0/24
IP WAN = 2.2.2.2
Now what I need to do, is to have all traffic from B to go to the site one even traffic destined to the internet. That is, I need internet traffic out of our network with the IP 1.1.1.1, even if it is from the network B.
On my I have set up a route 1.1.1.1 of the ISP, then a value by default 0/0 to 192.168.1.1 it ASA knows how to get to the peer VPN is a more specific route, but sends everything above the tunnel, at the remote end which then hairpin of ASA routes internet outside its own WAN port traffic.
I can understand though not how to so the same thing on the pair of SRX5308 they either don't raise the tunnel or internet route to the local site address B.
Anyone have any ideas?
I need to do this because we are logging and monitoring of internet traffic to A site via tapping from upstream to various IDS solutions and will not (cannot) reproduce this to all our remote sites.
Thank you
Dave.
After some more thought and testing I came up with a workable solution to my own problem. I'll share it here in case it can help others.
(1) use the wizard at both ends to implement a normal VPN that connects the two segments of network 192.168.1.0 and 192.168.2.0
(2) go to site VPN - VPN policy remote router192.168.2.1 and click Edit
(a) disable Netbios
(b) select "None" from the drop-down list the remote IP address.
(c) to apply the change
3) go to the VPN-> VPN policy on the head end site (192.168.1.1) and click Edit
(a) disable Netbios
(b) select "None" from the drop-down list the local IP address
(c) to apply the change
Now all the traffic wil go down the VPN tunnel and exit to the internet on the site of head end. Hope this helps others with the same question.
-
Use the remote website via VPN site-to-site
Hi all
We have two sites, the site has and B. At site A, we have a Web site we want to share with all of site B. Currently, site B can access the site via the VPN site-to site on X 0, which is their LAN. Nothing outside X 0 cannot access or ping to the address.
We added access rules to allow access from the DMZ to this interface, but again, no ping and no communication at all. The other strange thing is that we see that no trip package for these access rules either.
Any help is appreciated. Thank you.
It seems that the demilitarized zone is not part of the VPN tunnel.
Can you confirm that the DMZ subnet is part of local destinations on the site B and a part of the local destinations on site?
Kevin
-
Cisco 3640 to the PIX 501 site 2 site VPN performance specifications.
I intend on creating a site-2-site VPN in Star configuration with a Cisco 3640 as the hub and PIX 501 at the remote sites. My question is around the plug that I read.
.
The specifications for a PIX-501-BUN-K9 tell PIX 501 3DES Bundle (chassis, SW, 10 users, 3DES).
.
A question is what really "10 users. Which is the limit of the number of concurrent sessions, I have on the VPN at a given time, or that it means something else?
.
I also read the specs say that the Maximum number of VPN tunnels that can support a PIX 501 is 5. Because I'm not going to make a tunnel between the PIX 501 at the remote site and the 3640 on the central site, I think I would be OK. Is that correct or is the max value talk the maximum number of concurrent sessions on the tunnel tunnels?
.
Thank you.
UDP traffic always creates a session in the PIX so that the return traffic will be allowed in. The UDP timeout is 2 minutes but IIRC. If you go around NAT with a statement of "nat 0" should not create an xlate I think.
The real time is hard to say really, probably around 2 minutes for a UDP-only user, you would probably make a few 'local sho' orders on the PIX to really see for sure however.
Maybe you are looking for
-
Hey guys,. My iPod (4th gen classic monochrome, 20 GB) and iPod the same a friend both have the same problem - no start. Once connected, it only ever turn hard drive and display the logo of Apple for about 10 seconds and then off for a second, and re
-
Help, please I lost my installer for epson stylus sx515w drive, I have sent for a new disk but received an engineer reset disk, are they the same thing? and if so, how to install my printer?
-
Hello I use my first as a WAN Port LAN port. The IP address I get from my isp provider is a public IP address. I have a number of features, including a printer that connect via wifi. All of these devices also seem to get a public IP... How can I c
-
About two years ago, that this computer was so messed up with virus, we, had to reinstall windows. He's been through hp on the phone and they guided him thru or however they did. But now, for example, yesterday I downloaded CoreCad and they wanted th
-
Set up a wireless printer to a wireless network and to a computer with windows 7
My question is this; I would like to set up my HP 4500 wireless printer to a wireless network and on my laptop windows 7 at the same time. Does make a difference if I put it to the computer first, or the first wireless network?