Foot control

I am very new to Labview. I'm trying to simulate a footswitchcontrol for pulsed laser where pulse is defined by the user. I have amhaving wrong with the 2 functions of time. T1 is the switch closure(100-250mS) and t2 is the switch of the cycle time (500-1000 mS). I started with loop aa which I think is better in this case. I use usb Daq - Mx OR 6008. IHAVE tried to look for examples of similar code but have not found any. Anyhelp will be greatly appreciated.

Hi Jay,.

I'm not sure I understand your application.  What do you do for t1 and t2?  You control a switch with the 6008?  What it sounds like, you want a pulse with a great time T1 = 100-250 ms and a weak moment of t2 - t1, i.e. t1 + low time = t2 (total time).  Is this correct?  You use the digital lines or analog output?  This Post on the Discussion Forum will show you a good example for the creation of a digital pulse train programmed software.  This should work for your application, because you spend relatively slowly.

Tags: NI Hardware

Similar Questions

  • Event Structure/foot control

    All,

    I have a project I'm trying to acquire a reading of a Magna Mike. While I can do this successfully via a button on the user interface, my users want to use the supplied pedal that sends the data via RS-232 port. The pedal is connected the Magna Mike.

    My problem is that I can not understand how to tell Labview that the foot switch has been pressed and say that data are sent to the Structure of the event. Any ideas?

    do not use a structure of the event to the polling stations.

    in a vacuum vi put open visa initialize the serial port, you need, start a while loop and in this wile, use a shipment of t with endcharacters possible visa,.

    followed by a reading of x characters (the answer) visa and show that answer on the façade.

    user error in and sequencing error and check the error to stop the ored with a stop button loop read you also inside the loop.

    After the loop, you close the serial port of visa and display the content of the error e.

    Good luck

  • When you use USB foot control for transcription intermittently continues to play even when released. Tried the new foot controller.

    Recently, I upgraded my wife to a new pc with Windows 7 Home Premium on it.  The package of trancription she uses is WinScribe.  For knowledge, we kept his old Office XP with Word 2002.  After the IT person to society that it contracts for all their software set up and install a spell checker medical all seems to work well.  Well now, we just have a question.  She uses and uses an Infinity IN-USB-2 foot controller.  The question is when it plays its reports, intermittently when it leaves upward on the pedal to play that the report continues to play.  We have installed a new pedal, always with the same problem.  These controllers do not come with a dedicated driver, but are recognized by Windows.  Don't know if it's a problem of Windows 7 or not, but before, it was to use Windows XP with the same transcription software, the same product office and same foot controller without problem.  As a side note, my reason to replace his old computer was XP got to where she acted as if she had alzhiemers.  Has raced in many analyses of virus and malware scans with various products.  No permit.  Has happened to another pc, I have too.  Anyone who deals with this?

    Hello Larry,.

    Thanks for posting of query in Microsoft Community.

     
    I suggest you to contact Infinity IN-USB-2 feet and check with them.
    Support by email
     
    Hope the helps of information.
     
    Thank you
  • FS-85USB pedal for Digital Voice Editor

    I have a FS-85USB foot control unit and the CD is not compatible with Windows 8. You have a CD to update I can get if I can use the pedal on my computer to transcribe reports?

    Even if the software was not intended at window 8, this does not mean that it will not work. It is possible that you can install the software, and if it does not work you can try to run the program in compatibility mode. There is unfortunately no new software available for Windows 8.

  • FC50 with Mainstage problem

    Hello

    New to this! I generally find the answers given by the position of others, research but in this case, I have to ask because I've tried everything (I think):

    My hardware configuration

    • I have a CF-50 MIDI pedal boss that I'm trying to connect with Mainstage 3.
    • I want to use it as a trigger of foot controlled for different actions.
    • I am running Mainstage 3 using a M-Audio Pro fire 610 as my interface.
    • FC50 goes out to M - Audio Profire 610 interface MIDI IN

    My problem

    Although the buttons of the MIDI activity that I have in my page layout window light up when I press one of the CF-50 pedals (indicating that Mainstage indeed receives impulses from the pedal MIDI) I can not actually affect the FC50 pedal to the pedals or buttons in the window of available mainstage. In other words, the page layout buttons and pedals do not respond when I give one of them the pedal (nothing happens, they don't light upward, it not link set between the two). the pedal seems useless to me now.

    My setup of Mainstage

    In the control inspector (sidebar) layout mode screen, my configuration of input material is this, although I have tried many different combinations without success. Also the window MIDI at the top of the screen, each press on the foot control does not show a note (as B #, C D # etc.) just in the numbers.

    Any help on how to make Mainstage speak to the Boss FC - 50 would be appreciated!

    1 million thanks!

    Jon

    The internal buttons on the FC 50 Boss only sends MIDI program changes. To display the control buttons, you communicate us Mainstage MIDI control changes. In your configuration, you will need to use the FC50 with an external pedal control ports.

  • Problem of Lookout 6.0.2 modbus rtu?

    One of our clients has Lookout 6.0.2 communicates with several Packs of Scada CMI on wireless modems using the Modbus RTU Protocol. All of a sudden Friday night he got comm fail alarm pages on site all but one. The Modbus statistics window revealed that Lookout had stopped voting for all sites, except a single site that remained in communications. The only activity is a single site.

    He saw it queries this way for 2 hours, never to regain the normal polling cycle.

    I had him quit and relaunch Lookout and mark returned to normal and has been like this since late Friday night.

    This system has been in use for several years with very close 100% good communications sice we have deployed so far.

    It was obviously a Lookout failure, since the only approach was to quit and relaunch Lookout.

    Is there a timer for this kind of mistake?

    Is this a failure of the cbx Modbus object? (We use the plain vanilla Modbus driver)

    Roger Foote

    Foote control systems


  • Quirk of width of body on that I need possible Suggestions

    Hello

    I hope I can explain this clearly if someone can help me.  I am very familiar with the controls page and footer in Muse.  I did a quick and dirty site model:

    http://hissign.com/newdevelopment/footertest

    The model above is just something I threw together to show how if you use the width of the body of Muse and pull these header and footer controls, you will have a homogeneous fluid of the site that develops as a result.

    So, I'm now working on the re - create a Web site for a client in Muse.  The idea is to make all future changes to it in-House rather than go to the web design company and request changes, charging an arm and a leg.  Muse will obviously allow to happen for the client, who is excited by this ability.  I suggested a major redesign (I don't like the orange color scheme that currently exists), but was shot down.  Perhaps, which will take place on the road.

    In any case, so far my re-design will although it sounds about as close as I can do to the original.  But there is a quirk in the design.  Here is the link to my redesign.  If you want to see the comparison site, and developed by the company of the customer design, just delete everything in front of the root of the URL:

    http://hissign.com/newdevelopment

    Here is my whim.  Opinion on the two sites (mine and the original), this orange body where the white text is going on there.  In order for me to do my version looks exactly like the original, I had to draw a rectangle orange so it matches with the top of the header.  The header contains the logo, this Burgundy bar upstairs, and there is also the upper part of the background box orange "body".  I then called the second box orange and he joined with the upper part of the graph of the header of the orange box.

    The reason why I'm doing it this way is that to make my version looks like the original - and this background orange in the original being inside the header, I can't enjoy the width of the body in Muse - just make the width, the color orange and let it cascade down as the page develops vertically.

    Fact on the master pages that I keep having different masters and stretching from the orange box vertically either shorter or longer, depending on the content of the page.  It seems to work, but it is becoming a pain in the @ because you can imagine how I might have to continue to make various masters of different vertical diameter to contain the content of the page.

    So I'm tender hand to the community for just see if there is an easier way to do this - or maybe something that I know to get there.

    Again, I know that this sounds like something strange and weird to do.  In a perfect world, and if I was designing from scratch, I would certainly use the width of the Muse body like it should be used (and as I did when I threw together quick and dirty mock-up to the first link above).  But for this one, the only way I could get to is as described above.

    Thank you

    Deaf guy

    Here is my version of your master page. I did most of the things 75% transparent so you can see through them, I hope to better see where things are. The bright green line is located on the page.

  • How to control the footer to the NOSE section?

    Hello

    I have a problem with the release of the RTF on preprinted layout.

    The situation is the following:
    I have a RTF who send invoices. Each bill has certain number of lines and the RTF deadline 6 lines per page for each invoice.

    Some lines of the invoice contain values of media objects (line attachments) to JDE and they are very long in size.

    When I preview the output, for invoices with normal lines, they appear well and the footer will appear at the end (there is a dissociation if it's breaking 6 rows on each page until you find the footer)

    When the Bills have the multimedia objects (<?) Generic_Text_ID22? (> in the xml file), the footer is not printed at the bottom of the page, but somwhere in the middle.

    Please note that I do not use the foot of Page in MS Word to this effect, but a table at the bottom of the page.

    My questions are:
    1. by not using not to foot of Page in MS Word, how can I control the page footer section so that it appears in a fixed position at the bottom of the page? (Regardless of the attachment lines)
    2. using MS Word footer, how can I control the page footer section so that it is printed only on the last page of the invoice (if there is more than one page) instead of repeat on each page?

    Thank you.

    Move the total to the total and use logical Report footer section.

  • Weird problem with control of the ring and foot

    So I have some sort of weird issue with a control of the ring and a chart. I'm with LabWindows/CVI on a Windows 7 computer. The part of the program I'm looking at is basically to navigate through data - there are several "transition" (rehearsals experience), and you can choose the one that you want to watch in the list.

    Normally, you would select transitional in the list, it plots the data, then it is done, basically. However, all of a sudden (don't know how long it spent for), when I select anything except 'Average', he made all the tracing and such, then it changes control of the ring to 'Average' (it is not plot the average data or generate all the reminders that I can tell).

    Now the thing the more bizarre as you can see below, it seems that the switch happens just when I draw something on the chart:

     

    So, it's just weird. The code in this section is here:

       if(uidc.polyon) {
                polynomial_subtraction(curr_data, np, uidc.polyord, 0); // 0 Skip for now
            }
    
            // Scale the curr_data for gains, then pre-scale the FFT data
            // to have no change in the power spectrum (multiply by (2/np)
            for(j = 0; j < np; j++) {
                fft_data[j] = curr_data[j]*2/np;
                curr_data[j] = curr_data[j]*uidc.fgain[i] + uidc.foff[i];
            }
    
            uidc.fplotids[i] = PlotY(dc.fid, dc.fgraph, curr_data, np, VAL_DOUBLE, VAL_THIN_LINE, VAL_NO_POINT, VAL_SOLID, 1, uidc.fchans[i]?uidc.fcol[i]:VAL_TRANSPARENT);
    
            // Prepare the data.
            FFTEx(fft_data, np, npfft, NULL, FALSE, curr_fft);  // Do the fourier transform
    

    DC is a structure that I use to better organize some UI controls and uidc is for display RAM variables, then dc.fid is the Panel that is embedded in the tab "FID", dc.fgraph = FID_Graph and corresponds to the chart control. Control of the ring is actually in a child Panel, dc.cloc [0]. FID_Graph has a point, it can produce, but the reminder is empty (no not coded something there yet).

    I have also considered that perhaps something in another thread (I don't think there is, but whatever) I see is the cause, however, this behavior still happens on that line. I tried to break in different locations, on hold, then continues, as well by adding a loop containing Delay (0.01), a loop of 100 times. Always happens after the conspiracy.

    Does anyone have any idea why this might be happening?

    Hi Paul,.

    I don't have a solution, but I wanted to point out that, even if you see the ring to change its value only when you call the function of tracing, that doesn't say what this function call that really changes the value of the ring. In CVI, some drawing operations are batched, for performance reasons, and the Panel updates only visually at certain times. One of those moments when you draw a chart data. Yes, the ring changes visually at this time there, but it is probably just 'catch up' a change earlier.

    As you are looking through the code, when the value of the ring, you can use the term > command update UI to force the update panel, so that you don't have to wait for the tracing function and see if all goes well this change happening earlier.

    Luis

  • Google maps of more than footer, how to control?

    I've added the google map widget and dragged to the bottom of my head to the side of the page and finally to the top of my footer. When I post even if it grows and extends into the bottom of my Web page, is there a way to make sure that it is not in the footer?

    Seems odd, you pinned the map page or add the map in any new layer?

    Please try to publish the site as a place to test on BC and then check if its still the same behavior.

    Thank you

    Sanjit

  • I want to print a full URL in the footer of a printed page. How can I do this?

    I want the full Web page to print URL in the footer of the printed section. When I have the URL printed in the footer left section he gets cut by the Central footer section that is cut off by the footer to the right section.

    Firefox cut the URL in your print, if it's really long, and you also on the same line (header or footer), Date and Pages

    What I have summarized below are based on this page... http://www.watchingthenet.com/how-to-change-or-customize-Firefox-printing-defaults.html

    I have two questions:

    - - - - - - - - - - - - - - - - - - - - - - - - - - - -

    To fix, do a custom configuration for the header and footer as follows:

    Print / Page Setup / margins & header/footer / 'Customize' the 'left' as follows (leave the centre and right all white)

    & T
    D & U...... PT

    & D shows the short date: dd/mm/yyyy - and then the time

    To change the format of the short date in Win 8.1, go to:

    Control Panel / Date and time / Date and time tab / change the date and time / change the settings of the calendar.
    Date / date short... change of j/yyyy...... MM/DD/YY

    QUESTIONS RELATING TO THE:

    1.) how can you get rid of the time, who appears after the date? In Internet Explorer, you use a tiny "d" character - but that doesn't work here.

    2.) is it possible to change the right font for the header and the footer, to something like 10 of Microsoft Sans Serif?

    - - - - - - - - - - - - - - - - - - - - - - - - - - - -

    Firefox leaves no room around the text in the header and footer to the edge. To fix:

    Address Bar / about: config
    Enter the keyword "edge."
    Change then the four values of the printer that you use to:

    Print.printer_Foxit_PhantomPDF_Printer.print_edge_bottom... 5
    Print.printer_Foxit_PhantomPDF_Printer.print_edge_left... 10
    Print.printer_Foxit_PhantomPDF_Printer.print_edge_right... 10
    Print.printer_Foxit_PhantomPDF_Printer.print_edge_top... 5

  • With a point of foot to cut support it?

    I am running Native Instruments 'Battery' in MainStage, control everything with a keyboard and a Drumkat percussion controller. I want to be able to cut a note support (choke note) with a foot switch, similar to a function of starter of Charleston. Anyone know how I can get what is happening?

    Thank you!!!

    Maybe someone more on the forums of Native Instruments could help.

    https://www.native-instruments.com/Forum/forums/battery.35/

    TT2

  • HP Officejet Pro 8600: HP Officejet Pro 8600 cut header/footer when printing duplex

    Hey guys, frustrating problem slowing of my work, appreciate anyone who takes the time to volunteer expertise.

    Print single sided, my Word template prints very well. Select "print on both sides", "flip long edge ' and the footer no longer appears in the preview before printing (or printing) more the header is visible only half (and half printed).  Microsoft have no idea (when did ever right?).

    0.75 from the top header

    0.35 bottom footer

    (NB. the two characters 100% on single-sided and about two weeks, both printed fine on double-sided also). Date: July 15, 2015

    Hello again @Matt_Roberts,

    Thanks for getting back to me!

    If you have been able to print double-sided with no problems before using the same printer and the computer, it is unlikely that the machine itself has suddenly become incapable.

    What I think, is that it has something to do with the driver on your computer. Windows 8 has an annoying habit to install multiple instances of the driver for your printer. For example, even if you have installed the printer with the complete HP software, because the operating system can see the wireless printer, it can automatically install a driver from Windows update as well.

    So here's what I suggest we try. Check your printer for several "HP Officejet 8600" icons file.

    1. From your desktop, right of slide to unlock bar charms, or press Win key + C on your keyboard.
    2. Select settings in the bar on the right.
    3. Select Control Panel
    4. Under hardware and sound, select devices and printers.

    We will remove all software and start over. Right-click on each icon that you see for your 8600 (even if there is only one) and select the device you want to delete or remove.

    Once the printer has been deleted. Restart your computer. Then, download and run the HP printer installation wizard. It will automatically detect your product and install the latest driver available from HP package.

    Hope this helps! Fingers crossed.

  • How can I find and restore volume control that has disappeared from my system icons?

    The icon for the volume control in the toolbar at the foot of the screen disappeared.  How can I find it and restore?

    Hi Fran,

    Please see the following article for instructions that should help solve this problem: http://support.microsoft.com/kb/945011.

    Good luck!

    Kosh

  • I can't control my playlist on my clip +.

    I love my new sansa clip +, its small, convenient and very good. I use it for my foot in a Koss Sportapro liaison. But I have just a little problem. When I copy my songs in the repository of the MUSIC from my PC to my Clip +, I classify my music in my choice of preference. And when I listen to my music on my clip + all the songs are in a random order. And I can't impose my order! If anyone can help me. Note: The random function is disabled (sorry for my bad English, I'm french).

    HY, thank you for your response. I'm confused, but I found a solution. Time to fisrt I used my clip +, I used the menu "read everything" and then all the songs are played in a specific order imposed by the clip +. But when I used the 'list of reader', I can control and organize the order of the songs.

    I used this list this morning and it's ok. Thank you again for your help

    Kind regards.

Maybe you are looking for

  • Wireless stereo headset

    Installation goes well without any probs, but ist there is no sound! As I bought the helmet, there is no booklet or manual. For more than a week I m looking for the link to download the brochure! This home page is terrible confused! Help!

  • WPS WNDR3400v3 flashing on its own

    I looked but could not find something similar. I woke up two days and my wps light was flashing green on its own. It is above all the high wall so I cam see in my room and she flickered not standby or sign anything. I woke up and it was flashing gree

  • Missed calls log

    So, after all this time, I finally have a little question. All of a sudden my phone will not register my missed calls. No problems with ongoing calls. Right at the entrance. Anyone has any ideas. Thanks for any input.

  • 24V switch signal detection

    Hi all I have a PXI-1052 chassis with (among others) the following modules: PXI-6289 with a block of connection SCB-68. -Switch SCXI-1161 module. What do I want? I want to be able to spend the solenoid valves that operate on the 24 VDC. With the SCXI

  • R720: SWC0700: iDRAC is not ready [CF]

    Dopo a riavvio UN R720 mi ha dato he message in oggetto, che non riesce appunto indicating a way risposta dall'iDRAC. Ventole girano al massimo e quindi ho diversi malfunzionamenti has di operating system level, XenServer, che non riesce a completare