For ASA IPS modules

Hello

I would ask you to help learn p/n for the IPS/IDS modules in:

-ASA 5510

-ASA 5515 X

I would like to buy our dealer, but he asks that no part numbers, that he can't find them...

I know that for ASA5510 was AIP-SSM-10, but it currently is EOS. ASA 5515 X has software module, but I can't find this p/n.

Concerning

Hi Michal,

IPS-ASA5515-SSP

SSP ASA IPS 5515-X license

SF-ASAIPS64 - 7.1 - K9

ASA software IPS 5500-X 7.1 for IPS SSP

You can always check through "https://apps.cisco.com/Commerce/home".

It may be useful

G1

Tags: Cisco Security

Similar Questions

  • Logging in on a 5525 ASA IPS module

    Hi all

    Quick question here. I have a new ASA 5525 - X with IPS module.

    The PPE must be configured as an ID and told me that without fire view management controller, we can apply a license.

    I have also told me that with the 5525, we cannot install log in module to install the licenses. Please can someone confirm if I can install the licenses for the module? If so, how can I connect to the IDS to implement? Is this possible at all?

    Kind regards

    Riou

    That you listed is the legacy model, which is the end of the sale April 26, 2015. See this notice.

    They have their own Start Guide quick here.

    For these former IPS modules, you do not have licenses. Instead, your Smartnet must be the right kind of contract that includes coverage of subscription for the IPS signature updates.

    Legacy devices management IPS is via ASDM/IDM or, for slightly better visibility, through IPS Manager Express (IME). (There is also the option of Cisco Security Manager for the largest deployments).

    Signature update and software updates for older IPS modules can be done manually or automatically (assuming that you have a valid support contract, which includes the right of the subscription). Instructions for that are here.

  • Where can I get the license for the IPS module file?

    We just bought an ASA 5515 X with internal IPS module.

    I registed the IPS with Cisco and got a license key

    However, the module IPS needs a license file (, lic)

    I see nothing in the documentation or the instructions that came with the device to get this file. I don't see anything on the cisco Web page of license.

    can someone help me?

    Try this

    https://Tools.Cisco.com/swift/LicensingUI/ipsCryptoPage

  • In ASA IPS module allows you to scan 2 interfaces?

    I'm trying to figure if/how configure the ASA-SSM-20 for scan management/monitor interface and backplane (try to save money and buy not dedicated IPS/IDS for internal network). I'm under IPS v7.0 (8) E4 with v6.4 ASDM. I would use the management port to send traffic split of my Nexus 5548.

    Thank you!

    This feature is not supported at this time.

    Rafael

  • Update to the IPS Module

    I am trying to push an update via tftp for my IPS module, but am not sure how this cable.

    ASA internal Int: 10.1.3.1

    ASA IPS Mod: 10.1.9.201

    ASA IPS GW: 10.1.9.1

    What I owe my TFTP server directly to cable IPS module, or does it go in the interface internal? I tried both and my TFTP server is not displayed all traffic.

    The AIP - SSM module has its own management interface (it is the only ethernet on the face of the module). This must be connected to your TFTP server. Either directly (through a rollover cable) or through a switch or router.

  • Filtering in Cisco ASA using module sfr Web

    Hello

    I have Cisco ASA 5515-x version 9.2 (2) and I use ASDM version 7.2 (2). I module 5.3.1 LICO of ASA. I want to activate the ASA web filtering feature. Previously, I used the method of expression regex in the SAA to perform url filtering, but it was not effective. Since then, I have the license for the management of firesight I want to use it.

    But I am confused as some cisco docs say to set the firesight management in vmware while others offer to run the boot image in the SAA itself. What is the right way to do it?

    The show module command, I see that my module of sfr is in place so that means the sfr module is pre-installed, and I can't do a lot of configurations?

    It would be better for me to run ASA itself, but if it does not work like that then I will configure in VM. So please me clearify that concerns my options and my best chance.

    If it should be installed on a virtual machine or ASA itself, then please give me the link to download the boot images and other files on cisco.com. I have the user name and password, but did not find the correct software.

    Thank you in advance.

    Your ASA 5515-x performs the minimum version required to support the fire power module (sfr). The module also runs the initial version of the software of the firepower for ASA-based module firepower.

    With this combination of Software ASA and firepower on your device, you will need to use an external administrator of firepower to manage module (create strategies, apply licenses, monitor events etc.).

    From ASA 9.5 (1) and firepower 6.0, you have the opportunity to make the most of the same functions via ASDM. You must upgrade the ASA (both ASDM) and firepower to achieve module.

    In both cases, you should Protect licenses and URL filtering for the module of firepower.

    The Quick Start Guide is here: http://www.cisco.com/c/en/us/td/docs/security/asa/quick_start/sfr/firepo...

    See also the excellent vidoe Lab Minutes guides for firepower: http://labminutes.com/video/sec/ASA%20FirePower

    The ASA and ASDM software is here:

    https://software.Cisco.com/download/type.html?mdfid=284143128&flowid=31442

    Software module of firepower is here:

    https://software.Cisco.com/download/release.html?mdfid=286271171&flowid=...

    To run the power of fire management center VM, the software is here:

    https://software.Cisco.com/download/release.html?mdfid=286259687&flowid=...

    All the links above require a username cisco.com entitled (support agreement) to download the software.

  • Recover password of the IPS module (ASA)

    Dear experts,
     
    I have an ASA 5500 series with AIP SSM (IPS module), the username and password are lost.
     
    According to cisco portal, there are two approaches to recover the password:
    1 using the CLI command: hw-module module reset slot_number password;
    2. with the help of ASDM--> tools--> 'IPS password reset.
     
    Not sure whether the two commands to achieve the same result (retrieve password) or they may have different results (i.e. need to reset the module).
     
    The device is online, reset module is not privileged.
     
    After checking the information from the internet, it offers to reset the IPS module. Any problem will be produced if the IPS module is not reset?

    RDG
     
    Anita

    Hi Anita,.

    You can try using:

    HW-module module slot_number password reset

    Who will reset just the IPS to its default username/password:

    Cisco and cisco

    You can access the ASA CLI IPS:

    session 1

    Then type cisco and cisco (username/password)

    For example, you could add a new password.

    Don't forget to evaluate and select the right answer.

  • ASA ips feature

    I want to ask you what the works of IPS on ASAs functionality.

    There all the signatures, or it is limited?

    Perfect me if Iam wrong if I say that I needed module AIM for ips work on the asa. If Iam right, so why AIM has only 1 ethernet interface. This means that I am not follow 1 vlan?

    Thank you very much.

    The ASA-SSM-AIP-10 or ASA-SSM-AIP-20 according to the ASA modules is required for full monitoring of IPS features. The IPS on the MSS software is the same as for devices and other modules IPS. It uses the same software and signature updates. (Except for the image of the main system which has a few extra things to allow installation on the SSM)

    Without the ASA-SSM-AIP, the Software ASA itself has a set of very limited signatures that can be monitored. The signatures set is the same as in the previous version of the Pix Firewall.

    As for the single port on the ASA - SSM. This port is not a monitoring port. The port is the port command and control and has an IP address so that you can telnet, ssh or web browse to the sensor, so you can manage. The real follow-up is done on an internal interface connected inside firewall basket. The ASA can be configured through its policy to send packets through the SSM for the analysis of the IPS. Politics on the SAA can be configured for the IPS to monitor packets histocompatibility or inline.

    The SAA can be configured to send all or part of the packets through the firewall to monitor by the IPS of code that runs on the MSS.

    Since the external port is not a monitoring port that DFS may not be configured to control packets that do not go through the ASA. Packets must pass through the ASA ASA copy these packages through internal backplane to the SSM for analysis.

  • IPS module does not

    Hi, I'm currently running active / standby and my sometimes (twice a year) IPS module goes on which triggering a failover. The current status is:

    This host: secondary: enabled

    Another host: primary - failed

    and on the primary host-: slot 1: ASA-SSM-10 rev hw/sw (status 1.0/6.1(1)E3) (does not/high)

    I know that I have to go in the module and hw-module module reset. But I opened a file and got a replacement Module ID. Do I need to power down my ASA primary, it is in mode of failover in any case... If I turn off, it would result in any question of production since I am currently on secondary. Also, I read that the module will not keep or config between synchronization devices. How can I access the configuration of the IPS module so that I can put it in the new module?

    Thanks for the reply.

    FYI, these issues must be addressed with the CSE assigned to your request for Service of TAC where RAM was arranged. I'll take a shot at answering them, but when you use a query from Active Service of the TAC, you must act together with the CSE assigned to issues related to the issue.

    Do I need to power down my primary ASA

    Yes, sensor AIP - SSM modules are not able to SEE (Insertion/withdrawal online). ASA in which the sensor module is replaced must be powered down before removing the faulty sensor module and before installing the replacement.

    if I do power down, would it cause any issue to production since I am on secondary right now.

    If the other Member of the ASA of the failover pair is currently active and its sensor module is in Place, then power the unit standby off ASA should not affect traffic.

    I have read that the module won't retain or synch config between devices. how do i access the configuration of the IPS module so that I can put it into the new module?

    Correct, the sensor modules do inheritly not synchronize or replicate their configuration (such as units of the ASA of the failover pair). If you are able to access the defective sensor module long enough to get a copy of the "show config" command, you can integrate this same output in the replacement sensor module.

    Finally, note that the Unresponsive State can be caused by hardware problems. IPS 1.0000 E3 (which is what you seem to be running) is very old and is more directly supported. You need to upgrade to a modern version, supported (E4 7.0 (6) or 6.2 (4) E4), which contain a lot of bugs, which some correct problems that might otherwise cause the module become Unresponsive.

  • What traffic is copied to the IPS Module?

    We have an ASA5585-X with installed PSS-10 module that we test. External interface of the firewall is connected to the internet and has a public address. We have installed 4.2 CSM and send IPS events to it.

    After that we have configured the IPS module, we expected to get a lot of alerts for attacks from the internet, but we see almost nothing.

    The ACL on the external interface does actually not much, just a few SMTP, DNS, HTTP, SSH.

    My question is this - the IPS would all see the attacks/traffic from the internet or JUST packages that have passed the external ACL?

    I suspect that's why we rarely see alerts - can anyone confirm this?

    Thank you

    //\/\\\

    If traffic was abandoned by the ASA, then IPS will have no visibility to it.

    Kind regards

    Sawan Gupta

  • High utiization cpu IPS module

    I have two firewalls Cisco ASA5540X with IPS modules configured in a failover pair.

    Behind this pair Firewall (inside) is about 140 guests who use various web applications, minimal Internet, e-mail (host maybe 10) and a few small sharing/file access

    My IPS is configured for online analysis, but I noticed that the processor works 100% all the time (6 cores). Given that I don't want any circumvention traffic IPS, my firewall configuration looks like this

    ips_traffic of access allowed any ip an extended list

    ips_traffic list extended access udp allowed a whole

    class-map ips_class

    corresponds to the ips_traffic access list

    Policy-map global_policy

    class ips_class

    IPS inline help

    Why is such high usage on the IPS? What can I do here?

    Hello

    Although not an expert in this particular field, I installed a handful of them and each of them took one load CPU 100%, I was told by our support load of the CPU on an IPS is very inaccurate way to determine the load, it is preferable to use the inspection processing load.

    After more digging, I found this - the issue is addressed in this bug - CSCtl74475

    HTH

    Mike

  • License FireSIGHT - ASA IPS

    Hello

    I currently installs a virtual appliance of FireSIGHT to manage installed with fire services ASA 2.

    My Defense Center is an appropriate license, using the key PAK I got.

    I bought 2 IPS for two of the ASA subscription licenses.

    I have configured the Manager on both devices of sourcefire and added to the centre of defence.

    Now, my problem is: I can't attribute any IPS policy because there seems to be no licenses installed on the domain controller to be applied to devices...

    My question is: what I have to buy additional licenses for the domain controller for the IPS features (Protection) or do I missed something here? :-)

    Thank you very much

    Kind regards

    Hello

    As Marvin commented, you will have a license CTRL "ASA5525-CTRL-ICA" accompanying the device through a certificate of claim. On the certificate, you should see a number PAK and steps to save to get the license. Please follow these.

    If you have purchased a = L - ASA5525 - TA - LIC, then that gives you the right to obtain updates to signature for CONTROL-PROTECT features. There is no PAK or license for this PID.

    -DD

  • ASA IPS Signature unsuccessfully URL

    I want to update the signatures of ASA IPS by proxy. What are the destination URL I need to allow my proxy?

    I think www.cisco.com and dl.cisco.com should cover. The first has the metadata and the second is the source of the real signature files.

    Those are the two sites whose certificates in Cisco Security Manager, you must accept during the installation for the IPS signature updates.

  • IPS Signature DataBase - ASA IPS/IOS IPS/IPS 42xx/AIP-SSM

    Hello

    Can someone briefly tell me the details of database signature (number of Signature) among the following devices

    --> ASA IPS/IOS IPS/IPS 42xx/AIP-SSM.

    Thank you

    IPS on ASA/PIX = signatures only 50 or so common

    Module AIP - SSM is same signatures as the Cisco 4200 series sensors. Few minor differences exist (such as signature support IPv6 etc.)

    Please rate if useful.

    Concerning

    Farrukh

  • The ASA CX Module failover

    Hello

    I didn't send a CX module before. We are about to deploy firewalls 2xASA5585-X with CX (for STROKE and WSE) modules.

    I'm sure I know the answer to this (I've deployed a lot of old OLD ASA with CSC modules in them, and I'm guessing that the CX module has the same).

    1 will be the failure of the module CX trigger a failover event (fail-over active standby)? My guess is not?

    2. If it is not and policy service is set to 'closed' this means that the client should perform a manual failover to the secondary/sleep to restore access, web - this correct?

    Pete

    www.petenetlive.com

    Hi Pete,.

    1 will be the failure of the module CX trigger a failover event (fail-over active standby)? My guess is not.?

    Yes he custom of tipping your ASA, depends on configuration either will be allowed or close the traffic

    In the area if ASA CX card fails, click permit traffic or close traffic. The narrow traffic option defines the ASA to block all traffic if the ASA CX module is not available. Permits for movement option sets the ASA to allow all traffic through, if not inspected, the ASA CX module is not available.

    2 if it is not and the service policy is set to 'closed' this means that the client should perform a manual failover to the secondary/sleep to restore access, web - this correct? .When set to allow traffic CX failure, there is no need to manually failover your ASA firewall between HA

    Step 8 check the ASA CX check this box traffic flow.

    http://www.Cisco.com/c/en/us/TD/docs/security/ASA/Quick_Start/CX/cx_qsg.html#wp49530

    http://www.Cisco.com/c/en/us/TD/docs/security/ASA/asa84/configuration/guide/asa_84_cli_config/modules_cx.PDF

Maybe you are looking for